the great outdoors by Minka Lavery 72433-261 Installation guide

Type
Installation guide

The great outdoors by Minka Lavery 72433-261 is a stylish and functional outdoor lighting fixture that is perfect for illuminating your home's exterior. With its durable construction and easy installation, this fixture is a great choice for any homeowner.

The 72433-261 features a circular strap that attaches to the junction box and a support cable that supports the weight of the fixture while wiring. The fixture's wires are easily connected to the house wires, and the included clear silicone sealant helps to prevent moisture from entering the outlet box.

This fixture is compatible with a variety of light bulbs, so you can choose the brightness and color temperature that best suits your needs. The 72433-261 is also backed by a manufacturer's warranty, so you can be sure that it will provide years of reliable service.

The great outdoors by Minka Lavery 72433-261 is a stylish and functional outdoor lighting fixture that is perfect for illuminating your home's exterior. With its durable construction and easy installation, this fixture is a great choice for any homeowner.

The 72433-261 features a circular strap that attaches to the junction box and a support cable that supports the weight of the fixture while wiring. The fixture's wires are easily connected to the house wires, and the included clear silicone sealant helps to prevent moisture from entering the outlet box.

This fixture is compatible with a variety of light bulbs, so you can choose the brightness and color temperature that best suits your needs. The 72433-261 is also backed by a manufacturer's warranty, so you can be sure that it will provide years of reliable service.

Fig. 4
Caulking
Backplate
INSTALLATION INSTRUCTIONS
Item#72433-261
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
Fig. 3
Fig. 2
ASSEMBLING THE FIXTURE (Fig.1)
1.
Insert front glass (K) into door (J), and secure with clips
(L)
2. Insert back glass (M) and side glass (N) into
lamp body
(H) and secure with clips (I).
MOUNTING THE FIXTURE (Fig.2)
3.
Shut off the power at the fuse box or circuit breaker. If
ne
cessary, remove the old fixture, including the mounting
hardware.
4.
Carefully remove the new fixture from the carton and
check that all parts are included as shown in the
illustration.
5. Thread screws (A) into the pre-drilled holes in the
circular
strap (C) spaced the same distance apart as
the holes in
the back plate of the fixture body and s
ecure with hex nut
(B).
6. Attach the circular strap (C) to the junction box using
mounting screws (D) (size: #8-32N*L0.5”).The
side of
circular strap (C) marked “GND” must face out.
7.
The support cable is provided to support the weight of
the fixture while wiring. Align the fixture to circular strap
(C) and attach hook (G) on the end of support cable
into a slot located on circular strap (C)
. Carefully allow
the support ca
ble to support the weight of the fixture
while wiring. (Fig 2)
CONNECTING THE WIRES (Fig. 3)
8.
At this point, connect the electrical wires as shown in
figure3, making sure that all wire connectors are secured.
If your outlet has a ground wire (green or bare c
opper),
connect the ground wire from the fixture to it. Otherwise,
connect the ground wire from the fixture directly to the
circular strap (C) and secure with the green screw
provided. After wires are connected, tuck them carefully
into the outlet box. with cap nuts (F).
FINISHING THE INSTALLATION (Fig.2)
9.
To prevent moisture from entering the outlet box and
causing a short, use clear silicone sealant to outline the
outside of fixture back plate (E) where it meets the wall
leaving a space at bottom to allow
moisture a means to
escape. (Fig. 4)
10.
Install the light bulbs (not included)
in accordance with
the fixture’s specifications.
(DO NOT EXCEED THE
MAXIMUM WATTAGE RATING!). (
NE PAS
DEPASSER LA PUISSANCE NOMINALE
MAXIMALE!)
Your installation is now complete.
Return power and
test the fixture.
Note: Illustration (Fig.1) (Fig.2
) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Green or
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
Set
#
A
-
020
- Circular Strap
- Ground Screw
-
Mounting Screw*2
  • Page 1 1

the great outdoors by Minka Lavery 72433-261 Installation guide

Type
Installation guide

The great outdoors by Minka Lavery 72433-261 is a stylish and functional outdoor lighting fixture that is perfect for illuminating your home's exterior. With its durable construction and easy installation, this fixture is a great choice for any homeowner.

The 72433-261 features a circular strap that attaches to the junction box and a support cable that supports the weight of the fixture while wiring. The fixture's wires are easily connected to the house wires, and the included clear silicone sealant helps to prevent moisture from entering the outlet box.

This fixture is compatible with a variety of light bulbs, so you can choose the brightness and color temperature that best suits your needs. The 72433-261 is also backed by a manufacturer's warranty, so you can be sure that it will provide years of reliable service.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI