Grizzly T10501
The Grizzly T10501 Wood Lathe Center Kit is a 9-piece set of centers designed for use with a lathe that has a 1" x 8 TPI (RH) spindle and a tailstock that accepts MT#1 or MT#2 tooling.
The kit includes:
- 1 MT#2 Live Center
- 1 MT#1 Live Center
- 1 5/8" Spur-Drive Center
- 1 1" Spur-Drive Center
- 1 11/2" Spur-Drive Center
- 1 5/8" Multi-Spur Drive Center
- 1 1" Multi-Spur Drive Center
- 1 11/2" Multi-Spur Drive Center
- 2 Wrenches
- 1 Mounting Adapter 1" x 8 TPI
The live centers are used
Grizzly T10501
The Grizzly T10501 Wood Lathe Center Kit is a 9-piece set of centers designed for use with a lathe that has a 1" x 8 TPI (RH) spindle and a tailstock that accepts MT#1 or MT#2 tooling.
The kit includes:
- 1 MT#2 Live Center
- 1 MT#1 Live Center
- 1 5/8" Spur-Drive Center
- 1 1" Spur-Drive Center
- 1 11/2" Spur-Drive Center
- 1 5/8" Multi-Spur Drive Center
- 1 1" Multi-Spur Drive Center
- 1 11/2" Multi-Spur Drive Center
- 2 Wrenches
- 1 Mounting Adapter 1" x 8 TPI
The live centers are used
For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com
MODEL T10501
WOOD LATHE CENTER KIT
INSTRUCTIONS
COPYRIGHT © JULY, 2013 BY GRIZZLY INDUSTRIAL, INC.
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#DM15800 PRINTED IN CHINA
Introduction
The T10501 Wood Lathe Center Kit provides a
variety of centers for the specific weight, size, and
wood type of the workpiece to be turned.
This 9-piece kit is designed for a lathe with a 1"
x 8 TPI (RH) spindle and a tailstock that accepts
MT#1 or MT#2 tooling.
The included mounting adapter accepts the six
accompanying
5
⁄8", 1", and 1
1
⁄2" diameter four-spur
and multi-spur drive centers. The MT#1 and MT#2
live centers offer rigidity while providing ample
tool clearance. Two wrenches are provided for
tightening and loosening the mounting adapter
and drive centers to the spindle.
Description Qty
A. Live Center MT#2 ....................................... 1
B. Live Center MT#1 ....................................... 1
C. Spur-Drive Center
5
⁄8" ................................. 1
D. Spur-Drive Center 1" .................................. 1
E. Spur-Drive Center 1
1
⁄2" ............................... 1
F. Multi-Spur Drive Center
5
⁄8" ........................ 1
G. Multi-Spur Drive Center 1" .......................... 1
H. Multi-Spur Drive Center 1
1
⁄2" ...................... 1
I. Wrenches ................................................... 2
J. Mounting Adapter 1" x 8 TPI ...................... 1
Inventory (see Figure 1)
Assembly
This 9-piece center kit is designed for quick and
easy installation.
Select the spur-drive center according to work-
piece size, wood type, and moisture content. Spur
drive centers are best for soft or wet wood, while
shorter toothed multi-spur drive centers are ideal
for dry or hardwood.
Figure 1. T10501 inventory.
F
I
J
E
B
A
C
D
G
H
-2-
T10501 Lathe Center Kit (Mfg. 06/12)
To install a drive center onto spindle:
1. DISCONNECT LATHE FROM POWER!
2. Make sure threads of spindle and mounting
adapter are free of debris.
3. Thread the 1" female end of the mounting
adapter onto threaded spindle of headstock.
Holding spindle in place, firmly tighten adapt-
er using one of the wrenches provided.
4. Select drive center best suited for workpiece
to be turned. Thread the
5
⁄8" male end of
drive center into female end of the mounting
adapter.
5. Place wrenches in both mounting adapter
and drive center, as shown in Figure 2. While
holding mounting adapter, firmly tighten drive
center.
To remove center and adapter from spindle:
1. DISCONNECT LATHE FROM POWER!
2. Insert wrenches into hole on the mounting
adapter and drive center. While firmly holding
wrench, loosen the drive center by rotating it
counterclockwise.
3. Remove drive center by hand.
4. While holding the spindle in place, use one
of the wrenches to remove mounting adapter
from the spindle.
MT#1 and MT#2 live centers install into tailstock
quill and freely rotate with workpiece.
To install a live center:
1. Move the tailstock to a safe working distance
from the head and tool rest.
2. Loosen quill lock lever, then rotate quill
handwheel clockwise until quill extends out
from tailstock about 1", as shown in Figure 3.
3. Make sure live center and inside of quill are
free of debris and oily substances that could
interfere with proper mating.
4. Insert tapered end of live center into quill with
a quick, firm motion.
5. Make sure center is secure by attempting to
pull it out by hand—a properly installed cen-
ter will not pull out by hand.
6. Rotate quill handwheel to draw quill back into
tailstock as far as possible without forcing
center to release.
Note: For greatest workpiece support, retract
quill as close to tailstock as possible without
disengaging live center.
7. Tighten quill lock lever to hold quill and center
in place.
Figure 3. Installed live center.
Figure 2. Attaching drive center to adapter.
Spur Center Live Center
Mounting
Adapter
Drive
Center
Wrenches
To remove a live center:
1. While holding onto live center, retract quill
into tailstock with handwheel until center
becomes disengaged.
-
1
-
2
Grizzly T10501
The Grizzly T10501 Wood Lathe Center Kit is a 9-piece set of centers designed for use with a lathe that has a 1" x 8 TPI (RH) spindle and a tailstock that accepts MT#1 or MT#2 tooling.
The kit includes:
- 1 MT#2 Live Center
- 1 MT#1 Live Center
- 1 5/8" Spur-Drive Center
- 1 1" Spur-Drive Center
- 1 11/2" Spur-Drive Center
- 1 5/8" Multi-Spur Drive Center
- 1 1" Multi-Spur Drive Center
- 1 11/2" Multi-Spur Drive Center
- 2 Wrenches
- 1 Mounting Adapter 1" x 8 TPI
The live centers are used
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Grizzly W1752 Owner's manual
-
Grizzly Industrial G0462 Owner's manual
-
-
Grizzly Industrial T25926 Owner's manual
-
-
-
-
-
-
