Grizzly Industrial G0694 User manual

Brand: Grizzly Industrial

Model: G0694

Category: Lathes

Type: User manual

MODEL G0694

20" X 43" HEAVY-DUTY

VARIABLE SPEED

WOOD LATHE

OWNER'S MANUAL

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

(FOR MODELS MANUFACTURED SINCE 03/15) #TRCRBLTSJB11817 PRINTED IN TAIWAN

V3.0 6.18

This manual provides critical safety instructions on the proper setup,

operation, maintenance, and service of this machine/tool. Save this

document, refer to it often, and use it to instruct other operators.

Failure to read, understand and follow the instructions in this manual

may result in fire or serious personal injury—including amputation,

electrocution, or death.

The owner of this machine/tool is solely responsible for its safe use.

This responsibility includes but is not limited to proper installation in

a safe environment, personnel training and usage authorization,

proper inspection and maintenance, manual availability and compre-

hension, application of safety devices, cutting/sanding/grinding tool

integrity, and the usage of personal protective equipment.

The manufacturer will not be held liable for injury or property damage

from negligence, improper training, machine modifications or misuse.

Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to the State

of California to cause cancer, birth defects or other reproductive

harm. Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement and other masonry products.

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

Work in a well ventilated area, and work with approved safety equip-

ment, such as those dust masks that are specially designed to filter

out microscopic particles.

Table of Contents

INTRODUCTION ............................................... 2

Machine Description ...................................... 2

Contact Info.................................................... 2

Manual Accuracy ........................................... 2

Identification ................................................... 3

Controls & Components ................................. 4

Machine Data Sheet ...................................... 5

SECTION 1: SAFETY ....................................... 7

Safety Instructions for Machinery .................. 7

Additional Safety for Wood Lathes ................ 9

SECTION 2: POWER SUPPLY ...................... 10

SECTION 3: SETUP ....................................... 12

Needed for Setup ......................................... 12

Unpacking .................................................... 12

Inventory ...................................................... 12

Cleanup ........................................................ 13

Site Considerations ...................................... 14

Moving & Placing Lathe ............................... 15

Anchoring to Floor ....................................... 16

Test Run ...................................................... 17

SECTION 4: OPERATIONS ........................... 19

Operation Overview ..................................... 19

Workpiece Inspection................................... 20

Adjusting Tailstock ....................................... 20

Adjusting Tool Rest ...................................... 21

Outboard Tool Rest ..................................... 22

Installing/Removing Headstock Center ........ 22

Installing/Removing Tailstock Center .......... 23

Installing Faceplate/Handwheel ................... 24

Adjusting Spindle Speeds ............................ 25

Indexing ....................................................... 26

Selecting Turning Tools ............................... 27

Spindle Turning ............................................ 28

Faceplate Turning ........................................ 30

Outboard Turning ......................................... 31

Sanding/Finishing ........................................ 32

SECTION 5: ACCESSORIES ......................... 33

SECTION 6: MAINTENANCE ......................... 35

Schedule ...................................................... 35

Cleaning & Protecting .................................. 35

Spindle Bearing Lubrication ......................... 35

General Lubrication...................................... 37

SECTION 7: SERVICE ................................... 39

Troubleshooting ........................................... 39

Belt Adjustment ............................................ 41

Changing Belt/Bearing Service .................... 42

SECTION 8: WIRING ...................................... 47

Wiring Safety Instructions ............................ 47

Wiring Diagram ............................................ 48

Electrical Components ................................. 49

SECTION 9: PARTS ....................................... 50

Lathe ............................................................ 50

Stand ............................................................ 52

Stand Parts List ........................................... 53

Labels & Cosmetics ..................................... 54

WARRANTY AND RETURNS ........................ 57

-2-

Model G0694 (Mfd. Since 03/15)

INTRODUCTION

The G0694 20" x 43" Heavy-Duty Variable Speed

Wood Lathe is designed to turn wood stock so the

operator can remove material with a hand held

cutting tool called a chisel.

The variable speed control allows for infinite

spindle speed adjustment from 50–3,000 RPM

and the digital readout provides a precise reading

of the current spindle speed.

The outboard tool rest and double-sided spindle

allows for the turning of workpieces with diam-

eters larger than 20" on the outboard side of the

lathe.

Machine Description Manual Accuracy

We are proud to provide a high-quality owner’s

manual with your new machine!

made every effort to be exact with the

instruc-

tions, specifications, drawings, and photographs

in this manual. Sometimes we make mistakes, but

our policy of continuous improvement also means

that

sometimes the machine

you receive is

slightly different than shown in the manual

If you find this to be the case, and the difference

between the manual and machine leaves you

confused or unsure about something

check our

website for an updated version. W

e post

current

manuals and

manual updates for free

on our web-

site at

www.grizzly.com.

Alternatively, you can call our Technical Support

for help. Before calling, make sure you write down

the

Manufacture Date and Serial Number

from

the machine ID label (see below). This information

is required for us to provide proper tech support,

and it helps us determine if updated documenta-

tion is available for your machine.

Manufacture Date

Serial Number

Contact Info

We stand behind our machines! If you have ques-

tions or need help, contact us with the information

below. Before contacting, make sure you get the

serial number

and manufacture date

from the

machine ID label. This will help us help you faster.

Grizzly Technical Support

1815 W. Battlefield

Springfield, MO 65807

Phone: (570) 546-9663

Email: [email protected]

We want your feedback on this manual. What did

you like about it? Where could it be improved?

Please take a few minutes to give us feedback.

Grizzly Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

Email: [email protected]

Model G0694 (Mfd. Since 03/15)

-3-

Identification

Figure 1. Identification.

A. Outboard Tool Rest

B. Outboard Handwheel

C. Headstock

D. Faceplate

E. Spur Center

F. Bed

G. Tool Rest

H. Tool Rest Height Adjustment Lock

I. Tool Rest Holder Lock

J. Tailstock

K. Live Center

L. Quill

M. Quill Lock

N. Quill Adjustment Handwheel

O. Tailstock Base Lock

P. Stand

Q. RPM Digital Readout

R. Speed Dial

S. FWD/REV Switch

T. Emergency STOP Button

U. ON Button

For Your Own Safety Read Instruction Manual Before

Operating Lathe

a) Wear eye protection.

b) Do not wear gloves, necktie, or loose clothing.

c) Tighten all locks before operating.

d) Rotate workpiece by hand before applying power.

e) Rough out workpiece before installing on faceplate.

f) Do not mount split workpiece or one containing knot.

g) Use lowest speed when starting new workpiece.

-4-

Model G0694 (Mfd. Since 03/15)

Controls &

Components

To reduce your risk of

serious injury, read this

entire manual BEFORE

using machine.

A. ON Button: Starts the spindle rotation.

B. EMERGENCY STOP Button: Turns the

spindle rotation OFF.

C. Variable Speed Dial: Adjusts the spindle

speed from low to high within the range gov-

erned by the pulley belt position.

D. FWD/REV Switch: Toggles the spindle

direction between clockwise and counter-

clockwise.

E. RPM Digital Readout: Indicates the spindle

speed in RPM (revelations per minute).

Figure 2. Control panel.

F. Tailstock Base Lock: Secures tailstock in

position along bed.

G. Tailstock Handwheel: Moves quill toward

and away from spindle.

H. Quill Lock: Secures quill in position.

I. Quill: Holds centers or tooling. Can be

moved toward and away from spindle.

Figure 3. Tailstock lock lever.

J. Tool Rest Base (Banjo) Lock Lever:

Secures tool rest base (banjo) in position

along bed.

K. Tool Rest Lock Handle: Secures tool rest in

position.

L. Tool Rest: Provides stable platform for cut-

ting tools.

Figure 4. Location tool rest levers.

Refer to Figures 1–3 and the following descrip-

tions to become familiar with the basic controls of

this machine.

Model G0694 (Mfd. Since 03/15)

-5-

The information contained herein is deemed accurate as of 4/9/2019 and represents our most recent product specifications.

Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.

PAGE 1 OF 2

Model G0694

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901

MODEL G0694 20" X 43" HEAVY‐DUTY VARIABLE‐SPEED

WOOD LATHE

Product Dimensions:

Weight.............................................................................................................................................................. 578 lbs.

Width (side-to-side) x Depth (front-to-back) x Height................................................................... 103 x 25 x 49-1/2 in.

Footprint (Length x Width)..................................................................................................................... 77 x 16-1/2 in.

Shipping Dimensions:

Type.......................................................................................................................................................... Wood Crate

Content........................................................................................................................................................... Machine

Weight.............................................................................................................................................................. 814 lbs.

Length x Width x Height....................................................................................................................... 26 x 84 x 56 in.

Electrical:

Power Requirement........................................................................................................... 220V, Single-Phase, 60 Hz

Prewired Voltage.................................................................................................................................................. 220V

Full-Load Current Rating..................................................................................................................................... 19.6A

Minimum Circuit Size.............................................................................................................................................. 20A

Connection Type....................................................................................................................................... Cord & Plug

Power Cord Included.............................................................................................................................................. Yes

Power Cord Length................................................................................................................................................. 6 ft.

Power Cord Gauge......................................................................................................................................... 14 AWG

Plug Included........................................................................................................................................................... No

Recommended Plug Type..................................................................................................................................... 6-20

Switch Type.................................................................................................................... Push Button ON/OFF Switch

Inverter (VFD) Type.................................................................................................................................. Delta VFD-E

Inverter (VFD) Size............................................................................................................................................... 3 HP

Motors:

Main

Horsepower................................................................................................................................................ 3 HP

Phase.................................................................................................................................................... 3-Phase

Amps.............................................................................................................................................................. 9A

Speed........................................................................................................................................... 50-1725 RPM

Type........................................................................................................................................... TEFC Induction

Bearings........................................................................................................ Sealed & Permanently Lubricated

Centrifugal Switch/Contacts Type................................................................................................................ N/A

Main Specifications:

Operation Information

Swing Over Bed......................................................................................................................................... 20 in.

Swing Over Tool Rest Base................................................................................................................ 16-1/4 in.

Distance Between Centers........................................................................................................................ 43 in.

Swing Over Gap.................................................................................................................................. 24-7/8 in.

Max. Distance Tool Rest to Spindle Center................................................................................................. 8 in.

No of Spindle Speeds............................................................................................................................ Variable

Spindle Speed Range................................................................................................................ 50 – 3000 RPM

Floor to Center Height............................................................................................................................... 45 in.

Machine Data Sheet

-6-

Model G0694 (Mfd. Since 03/15)

The information contained herein is deemed accurate as of 4/9/2019 and represents our most recent product specifications.

Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.

PAGE 2 OF 2

Model G0694

Spindle Information

Spindle Taper............................................................................................................................................ MT#2

Spindle Thread Size..................................................................................................................... 1-1/4" x 8 TPI

Spindle Thread Direction.................................................................................................................. Right Hand

Type of Included Spindle Center................................................................................................................. Spur

Outboard Spindle Thread Direction.................................................................................................. Right Hand

Outboard Spindle Size........................................................................................................................... 1-1/4 in.

Outboard Spindle TPI................................................................................................................................ 8 TPI

Tool Rest Information

Tool Rest Width............................................................................................................................... 13-13/16 in.

Tool Rest Post Diameter....................................................................................................................... 1-1/4 in.

Tool Rest Post Length........................................................................................................................... 5-1/8 in.

Tool Rest Base Height......................................................................................................................... 2-1/16 in.

Tailstock Information

Tailstock Taper.......................................................................................................................................... MT#2

Type of Included Tailstock Center............................................................................................................... Live

Construction

Bed.......................................................................................................................... Precision-Ground Cast Iron

Stand...................................................................................................................................... Pre-Formed Steel

Headstock............................................................................................................................................ Cast Iron

Tailstock............................................................................................................................................... Cast Iron

Paint Type/Finish.................................................................................................................................... Enamel

Features:

Single-Phase Inverter for 3-Phase Variable Speed Motor

Included Spur & Live Centers

13-3/4 in. Wide Outboard Tool Rest

Indexed Spindle Every 15 Degrees

3-Step Pulley System

Reversible Variable Speed Motor Control

Quick Release Belt Tension Lever for Quick Speed Range Changes

Model G0694 (Mfd. Since 03/15)

-7-

ELECTRICAL EQUIPMENT INJURY RISKS.

You can be shocked, burned, or killed by touching

live electrical components or improperly grounded

machinery. To reduce this risk, only allow qualified

service personnel to do electrical installation or

repair work, and always disconnect power before

accessing or exposing electrical equipment.

DISCONNECT POWER FIRST.

Always discon-

nect machine from power supply BEFORE mak-

ing adjustments, changing tooling, or servicing

machine. This prevents an injury risk from unin-

tended startup or contact with live electrical com-

ponents.

EYE PROTECTION. Always wear ANSI-approved

safety glasses or a face shield when operating or

observing machinery to reduce the risk of eye

injury or blindness from flying particles. Everyday

eyeglasses are NOT approved safety glasses.

OWNER’S MANUAL. Read and understand this

owner’s manual BEFORE using machine.

TRAINED OPERATORS ONLY. Untrained oper-

ators have a higher risk of being hurt or killed.

Only allow trained/supervised people to use this

machine. When machine is not being used, dis-

connect power, remove switch keys, or lock-out

machine to prevent unauthorized use—especially

around children. Make your workshop kid proof!

DANGEROUS ENVIRONMENTS. Do not use

machinery in areas that are wet, cluttered, or have

poor lighting. Operating machinery in these areas

greatly increases the risk of accidents and injury.

MENTAL ALERTNESS REQUIRED. Full mental

alertness is required for safe operation of machin-

ery. Never operate under the influence of drugs or

alcohol, when tired, or when distracted.

For Your Own Safety, Read Instruction

Manual Before Operating This Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions.

This manual uses a series of symbols and signal words intended to convey the level of impor-

tance of the safety messages. The progression of symbols is described below. Remember that

safety messages by themselves do not eliminate danger and are not a substitute for proper

accident prevention measures. Always use common sense and good judgment.

Indicates a potentially hazardous situation which, if not avoided,

MAY result in minor or moderate injury. It may also be used to alert

against unsafe practices.

Indicates a potentially hazardous situation which, if not avoided,

COULD result in death or serious injury.

Indicates an imminently hazardous situation which, if not avoided,

WILL result in death or serious injury.

Alerts the user to useful information about proper operation of the

machine to avoid machine damage.

NOTICE

Safety Instructions for Machinery

SECTION 1: SAFETY

-8-

Model G0694 (Mfd. Since 03/15)

WEARING PROPER APPAREL. Do not wear

clothing, apparel or jewelry that can become

entangled in moving parts. Always tie back or

cover long hair. Wear non-slip footwear to reduce

risk of slipping and losing control or accidentally

contacting cutting tool or moving parts.

HAZARDOUS DUST. Dust created by machinery

operations may cause cancer, birth defects, or

long-term respiratory damage. Be aware of dust

hazards associated with each workpiece mate-

rial. Always wear a NIOSH-approved respirator to

reduce your risk.

HEARING PROTECTION. Always wear hear-

ing protection when operating or observing loud

machinery. Extended exposure to this noise

without hearing protection can cause permanent

hearing loss.

REMOVE ADJUSTING TOOLS. Tools left on

machinery can become dangerous projectiles

upon startup. Never leave chuck keys, wrenches,

or any other tools on machine. Always verify

removal before starting!

USE CORRECT TOOL FOR THE JOB. Only use

this tool for its intended purpose—do not force

it or an attachment to do a job for which it was

not designed. Never make unapproved modifica-

tions—modifying tool or using it differently than

intended may result in malfunction or mechanical

failure that can lead to personal injury or death!

AWKWARD POSITIONS. Keep proper footing

and balance at all times when operating machine.

Do not overreach! Avoid awkward hand positions

that make workpiece control difficult or increase

the risk of accidental injury.

CHILDREN & BYSTANDERS. Keep children and

bystanders at a safe distance from the work area.

Stop using machine if they become a distraction.

GUARDS & COVERS. Guards and covers reduce

accidental contact with moving parts or flying

debris. Make sure they are properly installed,

undamaged, and working correctly BEFORE

operating machine.

FORCING MACHINERY. Do not force machine.

It will do the job safer and better at the rate for

which it was designed.

NEVER STAND ON MACHINE. Serious injury

may occur if machine is tipped or if the cutting

tool is unintentionally contacted.

STABLE MACHINE. Unexpected movement dur-

ing operation greatly increases risk of injury or

loss of control. Before starting, verify machine is

stable and mobile base (if used) is locked.

USE RECOMMENDED ACCESSORIES. Consult

this owner’s manual or the manufacturer for rec-

ommended accessories. Using improper acces-

sories will increase the risk of serious injury.

UNATTENDED OPERATION. To reduce the

risk of accidental injury, turn machine OFF and

ensure all moving parts completely stop before

walking away. Never leave machine running

while unattended.

MAINTAIN WITH CARE. Follow all maintenance

instructions and lubrication schedules to keep

machine in good working condition. A machine

that is improperly maintained could malfunction,

leading to serious personal injury or death.

DAMAGED PARTS. Regularly inspect machine

for damaged, loose, or mis-adjusted parts—or

any condition that could affect safe operation.

Immediately repair/replace BEFORE operating

machine. For your own safety, DO NOT operate

machine with damaged parts!

MAINTAIN POWER CORDS. When disconnect-

ing cord-connected machines from power, grab

and pull the plug—NOT the cord. Pulling the cord

may damage the wires inside. Do not handle

cord/plug with wet hands. Avoid cord damage by

keeping it away from heated surfaces, high traffic

areas, harsh chemicals, and wet/damp locations.

EXPERIENCING DIFFICULTIES. If at any time

you experience difficulties performing the intend-

ed operation, stop using the machine! Contact our

Technical Support at (570) 546-9663.

Model G0694 (Mfd. Since 03/15)

-9-

Additional Safety for Wood Lathes

Serious injury or death can occur from getting entangled in, crushed between, or struck

by rotating parts on a lathe! Rotating workpieces can come loose and strike operator or

bystanders with deadly force if they are improperly secured, rotated too fast, or are not strong

enough for the rotational forces required for turning. Improper tool setup or usage can cause

tool kickback or grabbing, resulting in impact injury or entanglement. To reduce the risk of

operator (or bystander) injury or death, anyone operating this machine MUST completely heed

the hazards and warnings below.

WEAR PROPER PPE. Always wear a face shield

and safety glasses when operating lathe. Do not

wear gloves, necktie or loose clothing. Keep long

hair away from rotating spindle.

USE CORRECT SPEEDS. Select correct spindle

speed for workpiece size, type, shape, and

condition. Use low speeds when roughing or when

turning large, long, or non-concentric workpieces.

Allow spindle to reach full speed before turning.

AVOID TOOL KICKBACK. This occurs when

turning tool is grabbed or ejected from workpiece

with great force. Commonly caused by poor

workpiece selection/preparation, improper tool

usage, or improper machine setup or tool rest

adjustment.

SAFELY PERFORM ROUGHING. Use correct

tool. Take light cuts, use low speeds, and firmly

support tool with both hands.

USE SHARP TOOLS. Sharp tools cut with

less resistance than dull tools. Using dull tools

increases the risk of tool kickback or grabbing.

SAFELY STOPPING ROTATION. Always allow

rotating workpiece to stop on its own. Never put

hands or another object on workpiece to stop it.

SAFELY MEASURE WORKPIECE. Only mea-

sure mounted workpiece after it has completely

stopped. Trying to measure a spinning workpiece

increases entanglement risk.

SANDING/POLISHING. To reduce entanglement

risk, remove tool rest before sanding. Never

completely wrap sandpaper around workpiece.

VERIFY WORKPIECE INTEGRITY. Verify each

workpiece is free of knots, splits, nails, or foreign

material to ensure it can safely rotate on spindle

without breaking apart or causing tool kickback.

PROPERLY PREPARE WORKPIECE.

Before mounting, cut off waste portions to

balance workpiece for safe rotation and removal

of large edges that can catch on tooling.

SECURE LOCKS. Verify tool rest, headstock,

and tailstock are secure before turning lathe ON.

SECURE WORKPIECE. Use proven setup tech-

niques and always verify workpiece (and centers/

tooling holding workpiece) are well-secured before

starting lathe. Only use high-quality fasteners with

non-tapered heads for faceplate attachment.

ADJUST TOOL SUPPORT. An improperly sup-

ported tool may be grabbed or ejected. Adjust tool

rest approximately

⁄4" away from workpiece and

⁄8" above workpiece center line to provide proper

support for turning tool. Firmly hold turning tool

with both hands against tool rest.

REMOVE ADJUSTMENT TOOLS. Remove all

chuck keys, wrenches, and adjustment tools

before turning lathe ON. These items can become

deadly projectiles when spindle is started.

CHECK CLEARANCES. Before starting spindle,

verify workpiece has adequate clearance by

hand-rotating it through its entire range of motion.

TEST NEW SETUPS. Test each new setup by

starting spindle rotation at lowest speed and

standing to side of lathe until workpiece reaches

full speed and you can verify safe rotation.

-10-

Model G0694 (Mfd. Since 03/15)

SECTION 2: POWER SUPPLY

Availability

Before installing the machine, consider the avail-

ability and proximity of the required power supply

circuit. If an existing circuit does not meet the

requirements for this machine, a new circuit must

be installed. To minimize the risk of electrocution,

fire, or equipment damage, installation work and

electrical wiring must be done by an electrician or

qualified service personnel in accordance with all

applicable codes and standards.

Electrocution, fire, shock,

or equipment damage

may occur if machine is

not properly grounded

and connected to power

supply.

Full-Load Current Rating

The full-load current rating is the amperage a

machine draws at 100% of the rated output power.

On machines with multiple motors, this is the

amperage drawn by the largest motor or sum of all

motors and electrical devices that might operate

at one time during normal operations.

Full-Load Current Rating at 220V . 19.6 Amps

The full-load current is not the maximum amount

of amps that the machine will draw. If the machine

is overloaded, it will draw additional amps beyond

the full-load rating.

If the machine is overloaded for a sufficient length

of time, damage, overheating, or fire may result—

especially if connected to an undersized circuit.

To reduce the risk of these hazards, avoid over-

loading the machine during operation and make

sure it is connected to a power supply circuit that

meets the specified circuit requirements.

Circuit Requirements for 220V

This machine is prewired to operate on a power

supply circuit that has a verified ground and meets

the following requirements:

Nominal Voltage .............................. 220V/240V

Cycle ..........................................................60 Hz

Phase .................................................... 1-Phase

Power Supply Circuit ......................... 20 Amps

Plug/Receptacle ............................. NEMA 6-20

For your own safety and protection of

property, consult an electrician if you are

unsure about wiring practices or electrical

codes in your area.

Note: Circuit requirements in this manual apply to

a dedicated circuit—where only one machine will

be running on the circuit at a time. If machine will

be connected to a shared circuit where multiple

machines may be running at the same time, con-

sult an electrician or qualified service personnel to

ensure circuit is properly sized for safe operation.

A power supply circuit includes all electrical

equipment between the breaker box or fuse panel

in the building and the machine. The power sup-

ply circuit used for this machine must be sized to

safely handle the full-load current drawn from the

machine for an extended period of time. (If this

machine is connected to a circuit protected by

fuses, use a time delay fuse marked D.)

Model G0694 (Mfd. Since 03/15)

-11-

Extension Cords

We do not recommend using an extension cord

with this machine.

If you must use an extension

cord, only use it if absolutely necessary and only

on a temporary basis.

Extension cords cause voltage drop, which can

damage electrical components and shorten motor

life. Voltage drop increases as the extension cord

size gets longer and the gauge size gets smaller

(higher gauge numbers indicate smaller sizes).

Any extension cord used with this machine must

be in good condition and contain a ground wire

and matching plug/receptacle. Additionally, it must

meet the following size requirements:

Minimum Gauge Size ...........................14 AWG

Maximum Length (Shorter is Better).......50 ft.

Grounding Instructions

This machine MUST be grounded. In the event

of certain malfunctions or breakdowns, grounding

reduces the risk of electric shock by providing a

path of least resistance for electric current.

Improper connection of the equipment-grounding

wire can result in a risk of electric shock. The

wire with green insulation (with or without yellow

stripes) is the equipment-grounding wire. If repair

or replacement of the power cord or plug is nec-

essary, do not connect the equipment-grounding

wire to a live (current carrying) terminal.

Check with a qualified electrician or service per-

sonnel if you do not understand these grounding

requirements, or if you are in doubt about whether

the tool is properly grounded. If you ever notice

that a cord or plug is damaged or worn, discon-

nect it from power, and immediately replace it with

a new one.

Serious injury could occur if you connect

machine to power before completing setup

process. DO NOT connect to power until

instructed later in this manual.

The power cord and plug specified under “Circuit

Requirements for 220V”

on the previous page

has an equipment-grounding wire and a ground-

ing prong. The plug must only be inserted into

a matching receptacle (outlet) that is properly

installed and grounded in accordance with all

local codes and ordinances (see figure below).

No adapter should be used with plug. If

plug does not fit available receptacle, or if

machine must be reconnected for use on a

different type of circuit, reconnection must

be performed by an electrician or qualified

service personnel, and it must comply with

all local codes and ordinances.

Serious injury could occur if you connect

machine to power before completing setup

process. DO NOT connect to power until

instructed later in this manual.

Figure 5. Typical 6-20 plug and receptacle.

Grounding Pin

Current Carrying Prongs

6-20 PLUG

GROUNDED

6-20 RECEPTACLE

-12-

Model G0694 (Mfd. Since 03/15)

SECTION 3: SETUP

The following are needed to complete the setup

process, but are not included with your machine.

Description Qty

• Additional People .........................At Least 1

• Safety Glasses ............... 1 For Each Person

• Cleaner/Degreaser ..................... As Needed

• Disposable Shop Rags ............... As Needed

• Lifting Equipment (At Least 750 lb. Rating):

— Forklift or Hoist ....................................... 1

—Lifting Straps ........................................... 2

• Precision Level ........................................... 1

Needed for Setup Inventory

Inventory: (Figure 6) Qty

A. Knockout Rod ............................................. 1

B. Tool Rests .................................................. 2

C. Spur Center MT#2 ...................................... 1

D. Live Center MT#2 ....................................... 1

E. T-Handle Hex Wrenches 3, 4mm ...... 1 Each

Figure 6. Model G0694 small component

inventory.

The following is a list of items shipped with your

machine. Before beginning setup, lay these items

out and inventory them.

If any non-proprietary parts are missing (e.g. a

nut or a washer), we will gladly replace them; or

for the sake of expediency, replacements can be

obtained at your local hardware store.

NOTICE

If you cannot find an item on this list, care-

fully check around/inside the machine and

packaging materials. Often, these items get

lost in packaging materials while unpack-

ing or they are pre-installed at the factory.

This machine was carefully packaged for safe

transport. When unpacking, separate all enclosed

items from packaging materials and inspect them

for shipping damage.

If items are damaged

please

call us immediately at (570) 546-9663.

IMPORTANT:

Save all packaging materials until

you are completely satisfied with the machine and

have resolved any issues between Grizzly or the

shipping agent. You MUST have the original pack-

aging to file a freight claim. It is also extremely

helpful if you need to return your machine later.

Unpacking

SUFFOCATION HAZARD!

Keep children and pets away

from plastic bags or packing

materials shipped with this

machine.

Model G0694 (Mfd. Since 03/15)

-13-

T23692—Orange Power Degreaser

A great product for removing the waxy ship-

ping grease from the non-painted parts of the

machine during clean up.

The unpainted surfaces of your machine are

coated with a heavy-duty rust preventative that

prevents corrosion during shipment and storage.

This rust preventative works extremely well, but it

will take a little time to clean.

Be patient and do a thorough job cleaning your

machine. The time you spend doing this now will

give you a better appreciation for the proper care

of your machine's unpainted surfaces.

There are many ways to remove this rust preven-

tative, but the following steps work well in a wide

variety of situations. Always follow the manufac-

turer’s instructions with any cleaning product you

use and make sure you work in a well-ventilated

area to minimize exposure to toxic fumes.

Before cleaning, gather the following:

• Disposable rags

• Cleaner/degreaser (WD•40 works well)

• Safety glasses & disposable gloves

• Plastic paint scraper (optional)

Basic steps for removing rust preventative:

Put on safety glasses.

Coat the rust preventative with a liberal

amount of cleaner/degreaser, then let it soak

for 5–10 minutes.

Wipe off the surfaces. If your cleaner/degreas-

er is effective, the rust preventative will wipe

off easily. If you have a plastic paint scraper,

scrape off as much as you can first, then wipe

off the rest with the rag.

Repeat Steps 2–3 as necessary until clean,

then coat all unpainted surfaces with a quality

metal protectant to prevent rust.

Gasoline and petroleum

products have low flash

points and can explode

or cause fire if used to

clean machinery. Avoid

using these products

to clean machinery.

Many cleaning solvents

are toxic if inhaled. Only

work in a well-ventilated

area.

NOTICE

Avoid harsh solvents like acetone or brake

parts cleaner that may damage painted sur-

faces. Always test on a small, inconspicu-

ous location first.

Cleanup

T23692—Orange Power Degreaser

A great product for removing the waxy shipping

grease from your machine during clean up.

Figure 7. T23692 Orange Power Degreaser.

Cleanup

-14-

Model G0694 (Mfd. Since 03/15)

Site Considerations

Weight Load

Refer to the

Machine Data Sheet for the weight

of your machine. Make sure that the surface upon

which the machine is placed will bear the weight

of the machine, additional equipment that may be

installed on the machine, and the heaviest work-

piece that will be used. Additionally, consider the

weight of the operator and any dynamic loading

that may occur when operating the machine.

Space Allocation

Consider the largest size of workpiece that will

be processed through this machine and provide

enough space around the machine for adequate

operator material handling or the installation of

auxiliary equipment. With permanent installations,

leave enough space around the machine to open

or remove doors/covers as required by the main-

tenance and service described in this manual.

See below for required space allocation.

Physical Environment

The physical environment where the machine is

operated is important for safe operation and lon-

gevity of machine components. For best results,

operate this machine in a dry environment that is

free from excessive moisture, hazardous chemi-

cals, airborne abrasives, or extreme conditions.

Extreme conditions for this type of machinery are

generally those where the ambient temperature

range exceeds 41°–104°F; the relative humidity

range exceeds 20%–95% (non-condensing); or

the environment is subject to vibration, shocks,

or bumps.

Electrical Installation

Place this machine near an existing power source.

Make sure all power cords are protected from

traffic, material handling, moisture, chemicals, or

other hazards. Make sure to leave enough space

around machine to disconnect power supply or

apply a lockout/tagout device, if required.

Lighting

Lighting around the machine must be adequate

enough that operations can be performed safely.

Shadows, glare, or strobe effects that may distract

or impede the operator must be eliminated.

Children or untrained people

may be seriously injured by

this machine. Only install in an

access restricted location.

Figure 8. Minimum working clearances.

Wall

220V Single-Phase

Power Source

30"

103"

36"

25"

Min. 30"

for Maintenance

Model G0694 (Mfd. Since 03/15)

-15-

Moving & Placing

Lathe

The Model G0694 is a

heavy machine (approx.

580 lbs.) Serious per-

sonal injury may occur

if safe moving methods

are not used. To be safe,

get assistance and use

power lifting equipment

rated for at least 750 lbs.

to move the shipping

crate and remove the

machine from the crate.

To move and place your lathe:

1. Remove the top crate from the shipping pal-

let.

2. To help balance the load, lock the outboard

tool rest assembly as close as possible to the

lathe body, then move the tailstock and cen-

ter tool rest assembly to the extreme right of

the bedway.

3. Remove the small items from the shipping

pallet, then remove the lag bolts securing the

lathe to the pallet.

Figure 9. Lifting straps positioned to lift the lathe.

4. Feed the lifting straps under the bedway, as

shown in Figure 9, making sure they spread

as wide as possible.

5. With assistance, steady the load and lift the

lathe from the shipping pallet.

— If the load is unbalanced, immediately

lower the lathe and reposition the lifting

straps as necessary. Repeat this step until

you are satisfied that the load is safely bal-

anced.

6. Have an assistant steady the load to keep it

from swaying as you lift the lathe only enough

to clear the shipping pallet and any floor

obstacles, then move it to its working loca-

tion.

-16-

Model G0694 (Mfd. Since 03/15)

Figure 11. Right side mounting flange.

Mounting Flange

Anchoring to Floor

Anchoring machinery to the floor prevents tipping

or shifting and reduces vibration that may occur

during operation, resulting in a machine that runs

slightly quieter and feels more solid.

If the machine will be installed in a commercial or

workplace setting, or if it is permanently connect-

ed (hardwired) to the power supply, local codes

may require that it be anchored to the floor.

If not required by any local codes, fastening the

machine to the floor is an optional step. If you

choose not to do this with your machine, we rec-

ommend placing it on machine mounts, as these

provide an easy method for leveling and they have

vibration-absorbing pads.

Lag shield anchors with lag screws (see below)

are a popular way to anchor machinery to a con-

crete floor, because the anchors sit flush with the

floor surface, making it easy to unbolt and move

the machine later, if needed. However, anytime

local codes apply, you MUST follow the anchoring

methodology specified by the code.

Machine Base

Concrete

Lag Screw

Lag Shield Anchor

Flat Washer

Drilled Hole

Figure 10. Popular method for anchoring

machinery to a concrete floor.

Anchoring to Concrete Floors

Number of Mounting Holes ............................ 8

Diameter of Mounting Hardware .................

⁄8"

Model G0694 (Mfd. Since 03/15)

-17-

Test Run

Once assembly is complete, test run the machine

to ensure it is properly connected to power and

safety components are functioning correctly.

If you find an unusual problem during the test run,

immediately stop the machine, disconnect it from

power, and fix the problem BEFORE operating the

machine again. The

Troubleshooting

table in the

SERVICE section of this manual can help.

DO NOT start machine until all preceding

setup instructions have been performed.

Operating an improperly set up machine

may result in malfunction or unexpect-

ed results that can lead to serious injury,

death, or machine/property damage.

Serious injury or death can result from

using this machine BEFORE understanding

its controls and related safety information.

DO NOT operate, or allow others to operate,

machine until the information is understood.

To test run machine:

1. Clear all setup tools away from machine.

2. Press EMERGENCY STOP button.

3. Connect machine to power by inserting power

cord plug into a matching receptacle.

The Test Run consists of verifying the following:

1) The motor powers up and runs correctly, and 2)

the EMERGENCY STOP button works correctly.

Figure 12. Resetting the EMERGENCY STOP.

5. To unlock the spindle so that it can freely

rotate in the next steps, pull the spindle lock

lever out and rotate it so that it is in the twelve

o'clock position, as shown in Figure 13.

Figure 13. Unlocking the spindle.

Spindle

Lock

Lever

4. Twist EMERGENCY STOP button clockwise

until it springs out (see Figure 11). This

resets the switch so the machine can start.

-18-

Model G0694 (Mfd. Since 03/15)

6. Turn the speed dial counterclockwise to set

the spindle speed at zero.

7. Connect the lathe to power.

8. Verify that the machine is operating cor-

rectly by pushing the ON button, then use the

speed dial to increase the spindle speed.

—When operating correctly, the machine

runs smoothly with little or no vibration or

rubbing noises.

— Investigate and correct strange or unusual

noises or vibrations before operating the

machine further. Always stop the machine

and disconnect it from power before inves-

tigating or correcting potential problems.

9. Press the EMERGENCY STOP button to

stop the machine.

10. WITHOUT resetting the switch, press the ON

button. The machine should not start.

—If the machine does not start, the

EMERGENCY STOP button safety feature

is working correctly.

—If the machine does start (with the

EMERGENCY STOP button pushed in),

immediately disconnect power to the

machine. The STOP button safety feature

is not working correctly. This safety feature

must work properly before proceeding with

regular operations. Call Tech Support for

help.

11. Verify that the power is not connected out of

phase by starting/stopping the machine in the

FWD direction and determining if the spindle

turns in the counterclockwise direction (look-

ing at the spindle from the tailstock side of the

lathe).

— If the spindle does NOT turn counter-

clockwise, it is turning in the wrong direc-

tion. Stop the machine, disconnect it from

power, then swap any two of the three

power wires inside the motor wiring junc-

tion box (refer to the Wiring Diagram on

Page 48 for specific information).

Page is loading ...

Grizzly Industrial G0694 User manual

Brand: Grizzly Industrial

Model: G0694

Category: Lathes

Type: User manual

Download PDF

report

Grizzly Industrial G0694 User manual

Grizzly Industrial G0694 User manual

Related papers

Other documents