Midmark Stationary Wall Mount Exam Table Installation guide

Type
Installation guide

Midmark Stationary Wall Mount Exam Table

Midmark Stationary Wall Mount Exam Table is a medical device designed for use in healthcare settings. It is a sturdy and stable table that can be mounted to a wall, making it ideal for use in small or crowded spaces. The table is made of durable materials and is easy to clean and maintain. It has a weight capacity of 400 pounds and is adjustable in height, making it suitable for patients of all sizes. The table also comes with a variety of accessories, including a paper roll holder, a sharps container, and a drawer for storage. It also has a comfortable padded surface that makes it comfortable for patients to lie on during examinations or procedures. The table is easy to assemble and can be installed in just a few minutes. It is also easy to disassemble for storage or transport.

Midmark Stationary Wall Mount Exam Table

Midmark Stationary Wall Mount Exam Table is a medical device designed for use in healthcare settings. It is a sturdy and stable table that can be mounted to a wall, making it ideal for use in small or crowded spaces. The table is made of durable materials and is easy to clean and maintain. It has a weight capacity of 400 pounds and is adjustable in height, making it suitable for patients of all sizes. The table also comes with a variety of accessories, including a paper roll holder, a sharps container, and a drawer for storage. It also has a comfortable padded surface that makes it comfortable for patients to lie on during examinations or procedures. The table is easy to assemble and can be installed in just a few minutes. It is also easy to disassemble for storage or transport.

16
"
standard
stud spacing
23 1/2
"
Bottom holes will be
approximately 10 7/8
"
from the floor for 36
"
standard counter top
Reinforce wall studs
with 2
"
x 10
"
board
secured between studs
1/8" diameter starter holes
for lag bolts (4 places)
Wall Mount Exam Table Setup Manual
Rev. AA2 (1/22/19)
Hole placement for the wall mount exam table
measures as shown. Do not pre-drill mounting
holes at this point, but refer to dimensions to insure
that your wall is braced correctly in the location
where you plan to mount the table.
If mounting the table to a masonry wall, appropriate
anchor hardware must be used.
Cross braces need to be installed between studs to minimize exing. Mounting holes for the wall mount exam table
are drilled 16" apart to correspond with standard wall stud placement. If not placing the wall mount table to match up
with existing wall studs, modications to the wall will be necessary.
If the wall mount exam table is to be
mounted such that it does not correspond
with the wall studs, secure 2" x 10" boards
between wall studs as a mounting surface.
Secure table properly. The wall mount table
is only as sturdy as its mounting.
Note
Refer to chase installation manual for mounting hole locations
in chase cabinet. To install table to chase, use hardware
included with chase cabinet. (3/8” bolts, washers and nuts)
Also use required bracket included in 002-10368-00 kit.
002-10368-00 Service Kit Required
1.
2.
3.
4.
Check levelness
Support Bracket
Angle Brace
Drill holes & install bolts
Check levelness
Installing the Wall Mount Exam Table
Midmark Corporation - Carthage Facilities
1000 Civil War Road
Area 5
Carthage, MO 64836
1-800-643-6275
Mount the top support bracket to the wall by drilling
the wall and bolting. Measure from the oor to desired
height. Be sure that the support bracket is mounted
level. (Bracket is shipped loosely bolted to the bottom
of the table top.)
Bolt the angle brace to table bottom with two bolts
included (already threaded into mounting holes). Place
the table top on carpet or something that will protect it
from scratching.
Hold the table against the wall, resting on the
support bracket that you bolted to the wall in
Step 1. Install two bolts to secure the table to
the support bracket.
Raise or lower the front of the table until the
table is level, then mark the wall where bottom
bolt holes need to be drilled into the wall. Drill
holes and install bolts to secure the bottom of
the brace to the wall.
www.midmark.com
  • Page 1 1
  • Page 2 2

Midmark Stationary Wall Mount Exam Table Installation guide

Type
Installation guide

Midmark Stationary Wall Mount Exam Table

Midmark Stationary Wall Mount Exam Table is a medical device designed for use in healthcare settings. It is a sturdy and stable table that can be mounted to a wall, making it ideal for use in small or crowded spaces. The table is made of durable materials and is easy to clean and maintain. It has a weight capacity of 400 pounds and is adjustable in height, making it suitable for patients of all sizes. The table also comes with a variety of accessories, including a paper roll holder, a sharps container, and a drawer for storage. It also has a comfortable padded surface that makes it comfortable for patients to lie on during examinations or procedures. The table is easy to assemble and can be installed in just a few minutes. It is also easy to disassemble for storage or transport.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI