Installation instructions
Oven / CombiSteam oven
Construction type 60-600
J32A.113-0
26.11.11 WIMA
1
These installation instructions apply to the models:
Identification plate
➤ Open the appliance door. The identification plate is located on the left trim panel
(see illustration).
Connection plate
➤ Open the connection box and pivot downwards. The connection plate is located
next to the connection terminal in the connection box (see «Installation»).
➤ Refer to the identification plate for specifications for the required mains voltage, current type and fuses.
➤ Application height of the appliance: up to max. 2000 m above sea level
The appliance should be installed by qualified personnel only. Each step must be carried out and checked in full in the order
specified.
Validity
Oven:
CombiSteam oven:
32A, 34A, 36A, 38A, 40A, 42A, 45A, 48A, 51A, 54A
61A, 63A
General notes
If fitting in flammable material, the guidelines and standards for low voltage installations and for the fire protection must be
strictly observed.
To ensure good ventilation, the niche in which the appliance stands must have a supply air opening of at least 25 cm
2
.
This appliance is considered to be suitable for use in countries having a warm damp equable climate (WDaE). It may also be
used in other countries. If used in warm damp equable climated countries, the appliance is to be supplied through a residual
current device (RCD) having a rated residual operating current not exceeding 30 mA.
Electrical connections
Electrical connections must made by trained electricians in accordance with the guidelines and standards for low voltage
installations and the specifications of the local electricity supply companies.
A plug-in appliance may only be connected to a socket outlet with earthing contact, installed according to specifications. An
all-pole mains isolating device with 3 mm contact opening should be provided in the house wiring system. Switches, plug and
socket devices, circuit breakers and fusible cut-outs which are accessible after installation and which have all-poles switching
are permissible as isolating devices. Effective earthing and separately installed neutral and earth conductors ensure safe and
fault-free operation. After installation, live parts and cables with basic insulation must not be accessible. Old installations should
always be checked.
Installation instructions
Oven / CombiSteam oven
Construction type 60-600
J32A.113-0
26.11.11 WIMA
2
Installation for niche height of 600 mm
1. Slide appliance approx. 19 cm into the niche. Caution: danger of tipping over!
2. Pivot connection box D downwards after loosening screw S1.
3. Draw connection cable H from the point where it leaves the wall and through hole L and press firmly on snap lock clamp E to secure
the strain relief.
4. Connect connection cable to connecting terminal G in accordance with connection plate F.
5. Pivot connection box D upwards and fasten with screws S1.
6. Slide appliance into the niche until flush with the front and fasten the sides from the front with the 4 enclosed screws S2.
Installation variant for a niche height of 635 mm with adapter frame (see J731.050)
Installation
Open snap lock E for the strain relief using screwdriver.
=
=
30
min. 550
600
560–568
594
20
X
548
548
S2
598
S2
~45
(567)
440
D
E
S1
G
L
F
~16˚
~85˚
596
H
594
Niche
598
Appliance
Detail X
D Connection box
E Snap lock
F Connection plate
G Connection terminal
H Connection cable
L Hole for connection cable
S1 Screw for connection box
S2 Fastening screws (4×)
598
596
=
=
30
600
560–568
635
20
(567)
548
596
480
35
560
548
19.5
min. 550
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
V-ZUG 619 Installation guide
-
V-ZUG 58A Installation guide
-
-
-
-
V-ZUG 28A Installation guide
-
Whirlpool MWC-XSL/60 Mirror Installation guide
-
-
-