V-ZUG 89A induction glass ceramic hob offers precise and efficient cooking with its advanced induction technology. It features multiple cooking zones that allow you to cook several dishes simultaneously, saving time and energy. The hob's sleek design and easy-to-use controls make it a stylish and functional addition to any modern kitchen.
V-ZUG 89A induction glass ceramic hob offers precise and efficient cooking with its advanced induction technology. It features multiple cooking zones that allow you to cook several dishes simultaneously, saving time and energy. The hob's sleek design and easy-to-use controls make it a stylish and functional addition to any modern kitchen.
Installation instructions
Induction glass ceramic hob
With normal mounting frame
J89A.113-1
1.3.12 WIMA
1
These installation instructions apply to the model: 89A (GK56TIMSC)
Identification plate
The identification plate is located next to the connection plate
➤ Affix the second identification plate (supplied) in an accessible position behind the
front of the fitted cabinet beneath the appliance
➤ Refer to the identification plate for specifications for the required mains voltage, current type and fuses.
➤ Application height of the appliance: up to max. 2000 m above sea level
➤ The appliance is equipped with a mains cable that should be connected to a distribution box by the customer.
The appliance should be installed by qualified personnel only. Each step must be carried out and checked in full in the order
specified.
Validity
General notes
If fitting in flammable material, the guidelines and standards for low voltage installations and for the fire protection must be
strictly observed.
This appliance is considered to be suitable for use in countries having a warm damp equable climate (WDaE). It may also be
used in other countries. If used in warm damp equable climated countries, the appliance is to be supplied through a residual
current device (RCD) having a rated residual operating current not exceeding 30 mA.
Accessories
Designation Art. no.
Ventilation protective plate set
For niche width 550 mm
For niche width 600 mm
For niche width 825 mm
For niche width 900 mm
H6.1082
H6.1083
H6.1084
H6.1085
Electrical connections
Electrical connections must made by trained electricians in accordance with the guidelines and standards for low voltage
installations and the specifications of the local electricity supply companies.
A plug-in appliance may only be connected to a socket outlet with earthing contact, installed according to specifications. An
all-pole mains isolating device with 3 mm contact opening should be provided in the house wiring system. Switches, plug and
socket devices, circuit breakers and fusible cut-outs which are accessible after installation and which have all-poles switching
are permissible as isolating devices. Effective earthing and separately installed neutral and earth conductors ensure safe and
fault-free operation. After installation, live parts and cables with basic insulation must not be accessible. Old installations should
always be checked.
Connection plate
Identification plate
900/825
600/550
Clamp
Installation pipe
Distribution bo
x
230 V~
AUS/NZ
PE/ green/yellow
N blue
L1 brown
L1 brown
L2 black
L3 grey
N blue
PE/
yellow/gree
n
400 V~ 3 N
Installation instructions
Induction glass ceramic hob
With normal mounting frame
J89A.113-1
1.3.12 WIMA
2
Error message U400
Indications
• The work surface has to be flat.
• In order to guarantee good ventilation, there needs to be a space of at least 2 cm height beneath the appliance.
Installing
1. Create an accurate installation cut-out.
2. Carefully place the appliance in the mounting cut-out and press against the work surface with sufficient overlap.
Cool air supply if installed over a drawer or cabinet
In order to guarantee good ventilation, a space of at least 17.5 mm height is necessary beneath the appliance.
Incorrect connection:
A pole conductor was connected to the connecting terminal for neutral conductors.
Quickly disconnect the appliance from the mains!
Installation
The layout of the cooking zones on the integrated hob may differ from the illustrated hob!
A = Necessary space below the work surface for the ventilation of the appliance.
B = Cut-out in side walls for installation, only for niche width 600/550 mm.
514
910
48
900/825
(30)
600
886 ±1
min. 50
490 ±1
min. 50
Z
For symmetrical fitting
it is not necessary to
cut out the side walls.
50.5
Cable length 1.7 m
Aim for
max. R10
min. 5
max. 60
==
min. 15
min. 30
600/550
==
min. 240 min. 245
Drawer Centre of fan
Air gap over the entire cabinet element width
min. 25 cm²
Necessary space for the ventilation
below the worktop required
min. 50.9
min. 65.9
Installation instructions
Induction glass ceramic hob
With normal mounting frame
J89A.113-1
1.3.12 WIMA
3
Installing the protective plate with a 3 mm ventilation gap at the front (see Accessories)
A protective plate is necessary for the adequate ventilation of the hob.
The distance between the underside of the appliance and the protective plate must be at least 17.5 mm.
5.10
55.5
min. 67.5
(30)
min. 3
max. 0.5
(2.5)
56
393
ø4
min. 15
(19.5)
48
Air gap over entire
cabinet width min. 17 cm
2
Well-fitting seal
over cabinet width
Fan
Drawer
According to template
Caution:
Do not put mains cable
near protective plate
-
1
-
2
-
3
V-ZUG 89A induction glass ceramic hob offers precise and efficient cooking with its advanced induction technology. It features multiple cooking zones that allow you to cook several dishes simultaneously, saving time and energy. The hob's sleek design and easy-to-use controls make it a stylish and functional addition to any modern kitchen.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
V-ZUG 89A Installation guide
-
-
V-ZUG 975 Installation guide
-
V-ZUG 31002 Installation guide
-
-
V-ZUG 86A Installation guide
-
-
-
-
V-ZUG 31001 Installation guide