PARMIDA 4ft LED T8 Tybe B Tube 5CCT Installation guide
- Type
- Installation guide
4FT LED T8 TYPE B TUBE - 5CCT
WWW.PARMIDA.COM
INSTALLATION MANUAL
PLED-T8DS18W5CCT-C
PLED-T8DS18W5CCT-F
Table of Contents
4FT LED T8 TYPE B TUBE - 5CCT
03
03
04
04
05
05
06
INSTALLATION MANUAL
WARNING
RETROFIT INSTALLATION (TYPE B)
A. Retrofit luminaire with inductive ballast
B. Retrofit luminaire with electronic ballast
C. Retrofit luminaire with two lamps and one electronic ballast
D. Retrofit luminaire with three lamps and one electronic ballast
E. Retrofit luminaire with four lamps and one electronic ballast
DOUBLE - ENDED CONNECTIONSINGLE - ENDED CONNECTION
DOUBLE - ENDED CONNECTIONSINGLE - ENDED CONNECTION
A. Retrofit luminaire with inductive ballast
S
A
L
N
G
B
AC INPUT
· Disconnect the wires between starter and ballast according
to the figure.
· Connect two wires to branch circuit L and N according to the
figure.
L N
AC INPUT
S
S
L N
AC INPUT
S
OR
OR OR
AC INPUT
AC INPUT
OR
03 04
INSTALLATION MANUAL
Dual Mode Internal Driver For Compatible Tube
Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If not
qualified, do not attempt installation. Contact a qualified electrician.
Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and dimensions
shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input
rating of the luminaire.
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
Installers should not disconnect existing wires from lampholder terminals to make new connections at lampholder
terminals. Instead installers should cut existing lampholder leads away from the lampholder and make new electrical
connections to lampholder lead wires by employing applicable connectors.
For a linear tubular LED lamp conversion, there shall be text or a diagram showing how the supply connections were
made to the lampholders so the correct connections will be made to the lamp when the lamp is installed or replaced.
This retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be deter-
mined by authorities having jurisdiction.
The luminaire, once modified as retrofit fixture will no longer operate fluorescent lamps.
These lamps should be installed by a licensed electrician.
These lamps are to be used indoors (damp or dry locations only). Not suitable for wet location.
This device is not suitable for use with emergency ballasts or dimming ballasts.
RETROFIT INSTALLATION (TYPE B)
SELECTING COLOR TEMPERATURE
Please install your LED tubes according to the Type B Installation Method instructions below.
· Can be installed with either single or double ended connection.
· Double - ended connection can be used with either shunted or non-shunted sockets (tombstones).
· For single - ended connection, use only non-shunted sockets.
· Use either end to make single - ended connection.
To avoid risk of damage, ensure wall switch connected to the light is turned to off position before changing or selecting
desired color temperature (CCT) on the selector switch.
Select the color temperature via the CCT switch located on the LED lamp’s base. Using this switch, select the desired color
temperature (3000K Soft White or 3500K Neutral White, 4000K Cool White, or 5000K Day Light, or 6000K Bright White).
•
•
•
•
•
•
•
•
•
•
•
1. Disconnect power to the light fixture at the breaker panel before installation.
2. Remove the diffuser lens from the light fixture (if applicable).
3. Remove any existing fluorescent tubes by rotating them a one quarter turn and sliding them out.
4. Remove ballast cover (cover may be secured with screws or tabs).
5. Retrofit light fixture according to the diagram applicable to your fixture.
L
L
L
L
N
N
N
N
AC INPUT
AC INPUT
AC INPUT
L
N
AC INPUT
AC INPUT
3000
3500 4000 5000
6000
5 CCT SELECTOR SWITCH
B. Retrofit luminaire with electronic ballast
AB
· Disconnect the wires between tombstone and ballast
according to the figure.
· Connect two wires to branch circuit L and N according to
the figure.
DOUBLE - ENDED CONNECTIONSINGLE - ENDED CONNECTION
C. Retrofit luminaire with two lamps and one electronic ballast
· Disconnect the wires between tombstone and ballast
according to the figure.
· Connect two wires to branch circuit L and N according to
the figure.
OR
OR OR
L
N
AC INPUT ELECTRONIC
BALLAST
L
N
AC INPUT ELECTRONIC
BALLAST
A
B
A
B
ELECTRONIC
BALLAST L N
AC INPUT L N
AC INPUT
ELECTRONIC
BALLAST
L N
AC INPUT
ELECTRONIC
BALLAST
ELECTRONIC
BALLAST
L N
AC INPUT
DOUBLE - ENDED CONNECTIONSINGLE - ENDED CONNECTION OR
OR OR
ELECTRONIC
BALLAST L N
AC INPUT L N
AC INPUT
ELECTRONIC
BALLAST
L N
AC INPUT
ELECTRONIC
BALLAST
ELECTRONIC
BALLAST
L N
AC INPUT
D. Retrofit luminaire with three lamps and one electronic ballast
· Disconnect the wires between tombstone and ballast
according to the figure.
· Connect two wires to branch circuit L and N according to
the figure.
DOUBLE - ENDED CONNECTION
SINGLE - ENDED CONNECTION OR
OR OR
ELECTRONIC
BALLAST LN
AC INPUT
L N
AC INPUT
ELECTRONIC
BALLAST
L N
AC INPUT
ELECTRONIC
BALLAST
ELECTRONIC
BALLAST
L N
AC INPUT
L
N
AC INPUT ELECTRONIC
BALLAST
A
B
A
B
A
B
05 06
OR OR
E. Retrofit luminaire with four lamps and one electronic ballast
· Disconnect the wires between tombstone and ballast
according to the figure.
· Connect two wires to branch circuit L and N according to
the figure.
L
N
AC INPUT ELECTRONIC
BALLAST
A
B
A
B
A
B
A
B
6. Insert the LED tube by sliding pins into sockets and rotating a quarter turn until the LED tube locks in place.
7. Replace the diffuser lens of the light fixture (if applicable). LED lamps are now fully installed.
8. After installation has been completed, attach the Modification Replacement Cautionary Sticker Label to a visible area on
the luminaire and keep it visible after installation. Be sure to mark the type of wiring on the luminaire label (single or
double-ended).
9. Restore power to the circuit/luminaire and test the light. If necessary, adjust position of the LED tube(s)..
DOUBLE - ENDED CONNECTION
SINGLE - ENDED CONNECTION OR
ELECTRONIC
BALLAST L
N
AC INPUT
L N
AC INPUT
ELECTRONIC
BALLAST
L N
AC INPUT
ELECTRONIC
BALLAST
ELECTRONIC
BALLAST
L N
AC INPUT
07
-
1
-
2
-
3
-
4
-
5
PARMIDA 4ft LED T8 Tybe B Tube 5CCT Installation guide
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
SUNCO Type B 3ft LED Tube Light Installation guide
-
RAB T8 Operating instructions
-
RAB Lighting T8-18.5-48G-850-SD-BYP Operating instructions
-
PQL 90408 9040X LED Super Hybrid T8 User manual
-
-
RAB Lighting T8-8-24G-840-SE-BYP Operating instructions
-
-
Commercial Electric T8 Type B Ballast Bypass Single or Double Ended Line Voltage LED Tube User manual
-
-
