Commercial Electric T8 Type B Ballast Bypass Single or Double Ended Line Voltage LED Tube User manual

Brand: Commercial Electric

Model: T8 Type B Ballast Bypass Single or Double Ended Line Voltage LED Tube

Type: User manual

Commercial Electric T8 Type B Ballast Bypass Single or Double Ended Line Voltage LED Tube is a highly versatile and efficient lighting solution for a wide range of applications, providing significant energy savings and long-lasting performance.

This LED tube is designed to operate in temperatures ranging from -20°C to +45°C, making it suitable for both indoor and outdoor use. Its ballast bypass design allows for direct installation into fixtures without the need for a ballast, further simplifying the installation process.

The LED tube is available in various lengths and wattages, providing flexibility in choosing the appropriate illumination level for your specific needs. It emits a bright and evenly distributed light, ensuring optimal visibility and creating a comfortable ambiance.

USE AND CARE GUIDE

T8 Type B Ballast Bypass

Single or Double Ended Line Voltage

LED Tube Installation Instructions

Safety Information

FCC Regulation

THANK YOU

We appreciate the trust and conﬁdence you have placed in Commercial Electric through the purchase of this LED

light. We strive to continually create quality products designed to enhance your home. Visit us online to see our full

line of products available for your home improvement needs. Thank you for choosing Commercial Electric!

Questions, problems, missing parts? Before returning to the store,

call Commercial Electric Customer Service

8 a.m. - 7 p.m., EST, Monday - Friday

9 a.m. - 6 p.m., EST, Saturday

1-877-527-0313

HOMEDEPOT.COM

Item # 1005-179-396

Model # B9LT1800SGA2K20

Warranty

FIVE-YEAR LIMITED WARRANTY

The manufacturer warrants this lighting bulb to be free from defects in materials and workmanship

for a period of ﬁve (5) years from date of purchase. This warranty applies only to the original consumer

purchaser and only to products used in normal use and service. If this product is found to be defective,

the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the

product at the manufacturer’s discretion, provided that the product has not been damaged through

misuse, abuse, accident, modiﬁcations, alterations, neglect, or mishandling.

WHAT IS NOT COVERED

This warranty shall not apply to any product that is found to have been improperly installed, set-up,

or used in any way not in accordance with the instructions supplied with the product. This warranty

shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence,

alteration, faulty installation, or any other failure not relating to faulty material or workmanship.

This warranty shall not apply to the ﬁnish on any portion of the product, such as surface and/or

weathering, as this is considered normal wear and tear. The manufacturer does not warrant and

speciﬁcally disclaims any warranty, whether express or implied, of ﬁtness for a particular purpose,

other than the warranty contained herein. The manufacturer speciﬁcally disclaims any liability and

shall not be liable for any consequential or incidental loss or damage, including but not limited to any

labor / expense costs involved in the replacement or repair of said product.

Contact the Customer Service Team at 1-877-527-0313 or visit www.HomeDepot.com.

Quick Installation Guide

1. Always switch off the power supply before installation.

2. Ballast bypass model. Ballast must be removed before installation.

3. LED tubes operate in temperatures from -20°C to + 45°C.

4. Use in dry or damp locations or in luminaires that provide correct protection.

5. All LED tubes must be installed by a professional electrician.

6. Do not change any components of the LED tubes.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation. This equipment, if

not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. Any changes or modications not expressly approved by the manufacturer could

void the user's authority to operate the equipment.

Supplier’s Declaration of Conformity 47 CFR § 2.1077 Compliance Information

Responsible Party: Leedarson America, Inc. 300 Technology Court SE Suite 100; Smyrna, GA 30082

1-678-293-8382 Unique Identier: B9LT1800SGA2K20 (1005 179 396)

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures: reorient or relocate the receiving antenna; increase the separation between the

equipment and receiver; connect the equipment into an outlet on a circuit different from that to

which the receiver is connected; consult the dealer or an experienced radio/TV technician for help.

For single-ended wiring, do not install product in a xture with shunted lampholders (found in all xtures

using instant start ballasts). If the current lampholders are shunted, remove them and replace them with

non-shunted lampholders. Make new connections directly to terminals as indicated below.

The socket must be changed to non-shunted

socket in this connection.

The socket must be changed to non-shunted

socket in this connection.

Single-Ended Wiring lnstructions

NLEDlamp

Instant Start

Electronic

Ballast

Fluorescent lamp

Program Start or Rapid Start

Instant Start Program Start or Rapid Start

Electronic

Ballast

Fluorescent lamp

Retroﬁt Luminaire with One Lamp

Retrot Luminaire with Two Lamps

Electronic

Ballast

Fluorescentlamp

Electronic

Ballast

Fluorescentlamp

LLEDlamp

NLEDlamp

LEDlamp

LLEDlamp

NLEDlamp

Connect wires directly to these terminals

Typical Non-Shunted Lampholder

Double-Ended Wiring lnstructions

Input

Volts (Vac)

Input

Wattage (W) Base

Light

Output (LM)

120-277V 60 14.5 1,800 G13 Bin-

Pin Base

Input

Frequency (Hz)

The ballast wiring below represents typical conguration. The actual ballast wiring varies according to

ballast model. It is not necessary to change sockets (if in good condition) to operate double ended lamps,

regardless the type of sockets. Please make sure one side of xture is connected to Live (L) and the

other side to Neutral (N).

LEDlamp

Instant Start

Electronic

Ballast

Fluorescentlamp

Program Start or Rapid Start

Instant Start Program Start or Rapid Start

Electronic

Ballast

Fluorescent lamp

LEDlamp

Retroﬁt Luminaire with One Lamp

Retrot Luminaire with Two Lamps

Electronic

Ballast

Fluorescentlamp

Electronic

Ballast

Fluorescent lamp

LED lamp

LEDlamp

Double-Ended Wiring lnstructions (continued)

Instant Start Program Start or Rapid Start

Retrot Luminaire with Three Lamps

LEDlamp

...

Electronic

Ballast

Fluorescentlamp

LEDlamp

Electronic

Ballast

Fluorescentlamp

Instant Start Program Start or Rapid Start

Retrot Luminaire with Four Lamps

Electronic

Ballast

Fluorescent lamp

Electronic

Ballast

Fluorescent lamp

LEDlamp

Warnings

Speciﬁcations

10. This device is not intended for use with emergency exits.

11. This device is not intended for use with dimmable exits.

Lamp Quantity

4 FEET 1,251 mm (L) x 606 mm (W) x 75 mm (H) 4

MINIMUM LAMP COMPARTMENT DIMENSIONS

( LENGTH x WIDTH x HIGHT)

Single-Ended Wiring lnstructions (continued)

Instant Start Program Start or Rapid Start

Retrot Luminaire with Three Lamps

Electronic

Ballast

Fluorescentlamp

Electronic

Ballast

Fluorescentlamp

Instant Start Program Start or Rapid Start

Retrot Luminaire with Four Lamps

Electronic

Ballast

Fluorescent lamp

Electronic

Ballast

Fluorescent lamp

LLED

The socket must be changed to non-shunted

socket in this connection.

The socket must be changed to non-shunted

socket in this connection.

The socket must be changed to non-shunted

socket in this connection.

The socket must be changed to non-shunted

socket in this connection.

lamp

LEDlamp

LLEDlamp

LEDlamp

LLEDlamp

LEDlamp

LLEDlamp

LEDlamp

1. Risk of re or electric shock. LED Retrot Kit installation requires knowledge of luminaires electrical

systems. If not qualied, do not attempt installation. Contact a qualied electrician.

2. Risk of re or electric shock. Install this kit only in luminaires that have the construction features

and dimensions shown in the photographs and/or drawings and where the input rating of the retrot

kit does not exceed the input rating of the luminaire.

3. Do not make or alter any open holes in an enclosure of wiring or electrical components during kit

installation.

4. To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp

objects.

5. This xture must be grounded and installed in accordance with local and national electrical codes,

by a person familiar with the construction and operation of the product and the hazards involved.

6. Installers should not disconnect existing wires from lamp holder terminals to make new connections

at lamp holder terminals. Instead installers should cut existing lamp holder leads away from the lamp

holder and make new electrical connections to lamp holder lead wires by employing applicable

connectors.

7. Please examine all parts that are not intended to be replaced by the retrot kit for damage and replace

any damaged parts prior to installation of the retrot kit.

8. THIS RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE

COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING JURISDICTION. PRODUCT MUST BE

INSTALLED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH THE APPLICABLE AND APPROPRIATE

ELECTRICAL CODES. THE INSTALLATION GUIDE DOES NOT SUPERSEDE LOCAL OR NATIONAL

REGULATIONS FOR ELECTRICAL INSTALLATIONS.

9. The units covered by this report are intended to retrot surface mount, Type IC/Type Non-IC recessed

mount listed uorescent luminaires that use a maximum of 4 straight tubular lamps with or without a

diffuser. The minimum dimension of luminaries are tabulated below:

WARNING:

To avoid potential re or shock hazard, do not use this retrot kit in luminaires

employing shunted bin-pin lampholders.

Note: Shunted lamp holders are found only in uorescent luminaires with Instant-Start ballasts. Instant-

Start ballasts can be identied by the words "Instant Start" or "I.S." marked on the ballast. This

designation may be in the form of a statement pertaining to the ballast itself, or may be combined

with the marking for the lamps with which the ballast is intended to be used, for example F40T12/IS.

For more information, contact the LED luminaire retrot kit manufacturer.

Commercial Electric T8 Type B Ballast Bypass Single or Double Ended Line Voltage LED Tube User manual

Brand: Commercial Electric

Model: T8 Type B Ballast Bypass Single or Double Ended Line Voltage LED Tube

Type: User manual

Download PDF

report

Commercial Electric T8 Type B Ballast Bypass Single or Double Ended Line Voltage LED Tube User manual

Commercial Electric T8 Type B Ballast Bypass Single or Double Ended Line Voltage LED Tube User manual

Other documents