ENERLITES 51300L User manual

51300L
ENERLITES
Brand
ENERLITES
Model
51300L
Category
Dimmers
Type
User manual

ENERLITES 51300L is a low voltage dimmer designed to control 0-10V LED drivers or fluorescent ballasts. It operates on line voltage and provides a smooth dimming range from minimum to maximum light levels. The device features a simple slide control lever, adjustable high-end and low-end trim-pots for customized dimming range, and constant memory to restore the previous light level after a power failure. It can be used in single-pole or three-way configurations and is suitable for multi-gang installations.

ENERLITES 51300L is a low voltage dimmer designed to control 0-10V LED drivers or fluorescent ballasts. It operates on line voltage and provides a smooth dimming range from minimum to maximum light levels. The device features a simple slide control lever, adjustable high-end and low-end trim-pots for customized dimming range, and constant memory to restore the previous light level after a power failure. It can be used in single-pole or three-way configurations and is suitable for multi-gang installations.

INSTALLATION INSTRUCTIONS
DESCRIPTION/ FEATURES
51300L
0-10V LED Dimmer
Single Pole/Three-Way
SPECIFICATIONS
Voltage ........................................................................................................ 120-277 VAC 60Hz
Load rating.........................................................................................3A~120VAC, 1A~277VAC
0-10 V control link........................................................... ...................................................50mA
Operating Temperature.............................................................................................32°F-104°F
The 51300L is a low voltage 0-10V dimmer. It powered by line voltage to operate each 0-10V
LED driver or Fluorescent ballast. At 0 Volts the device will dim to the minimum light
level allowed by the dimming driver, and at 10 Volts the device will be operating at 100%.
WARNING
DIMMER ADJUSTMENTS
Turn the POWER OFF at the circuit breaker before
installing the Dimmer
Read and understand these instructions before installing. This device is intended for
installation in accordance with the National Electric Code and local regulations. It is
recommended that a qualified electrician performs this installation. Make sure to turn off
the circuit breaker or fuse(s).
Use copper wire only
WARRANTY INFORMATION
This device is warranted to be free of material and workmanship defects for 2 years from the date of purchase.
Original receipt or proof of purchase from an authorized retailer must be presented upon warranty claim. ALL
claims must be verified and approved by Enerlites, Inc. Warranties from other Enerlites products may vary. This
warranty is nontransferable and does not cover normal wear and tear or any malfunction, failure, or defect
resulting from misuse, abuse, neglect, alteration, modification, or improper installation. To the fullest extent
permitted by the applicable state law, Enerlites shall not be liable to the purchaser or end user customer of
Enerlites products for direct, indirect, incidental, or consequential damages even if Enerlites has been advised of
the possibility of such damages. Enerlites’ total liability under this or any other warranty, express or implied, is
limited to repair, replacement or refund. Repair, replacement or refund are the sole and exclusive remedies for
breach of warranty or any other legal theory.
MULTIGANG INSTALLATION
When installing more than one control in the same wall box, it may be necessary to remove the
side tabs before installing (see below). Using pliers, bend each tab back and forth until they
break off. Repeat for each tab to be removed. Removal of tabs WILL NOT effect maximum
load capacity.
Tabs may be Removed
for Mulitgang installation
•
Adjustable high-end and low-end trim-pot for maximum control over dimming range
•
Constant memory returns light to previous level after a power failure
•
Simple slide control lever to fade lighting up and down smoothly
•
Switch 120-277VAC
WIRING DIRECTIONS
Down:
Less bright
Slider: Controls light level Up
increases light level Down
decreases light level
Up:
Brighter
+
Maximum
Light
Level
(High End)
Trimpot
Shaft
UP
Minimum
Light
Level
(Low End)
Trimpot
Wheel
+
UP
Red
Green(Ground)
Gray (-)
Purple (+)0-10 V Ballast/Driver
0-10 V Ballast/Driver
Black
Neutral
Neutral
120 - 277 V~
Hot
Hot
Neutral
Hot
+
UP
0-10 V Ballast/
Driver
0-10 V Ballast/
Driver
Neutral
Hot
Neutral
Hot
Red
Red
Green(Ground)
Green(Ground)
Gray (-)
Purple (+)
Black
Neutral
3-Way
Switch
Hot
+
U
P
Dimming With ON/OFF Control
Dimming With ON/OFF Control for 3-Way
120 -
277 V~
Single-Gang RatingDevice Rating Double-Gang Rating
120V AC, 50-60Hz, 3A
277V AC, 50-60Hz, 1A
CFL/LED/Electronic
self-ballasted
120V AC, 50-60Hz, 3A
277V AC, 50-60Hz, 1A
CFL/LED/Electronic
self-ballasted
120V AC, 50-60Hz, 3A
277V AC, 50-60Hz, 1A
CFL/LED/Electronic
self-ballasted
120V AC, 50-60Hz, 3A
277V AC, 50-60Hz, 1A
CFL/LED/Electronic
self-ballasted
Triple-Gang Rating
Multi-gang Installation Rating:
Warehouse-Lighting.com
2750 South 163rd St
New Berlin, WI 53151
Warehouse-Lighting.com
Phone: 888-454-4480
info@warehouse-lighting.com
  • Page 1 1

ENERLITES 51300L User manual

51300L
ENERLITES
Brand
ENERLITES
Model
51300L
Category
Dimmers
Type
User manual

ENERLITES 51300L is a low voltage dimmer designed to control 0-10V LED drivers or fluorescent ballasts. It operates on line voltage and provides a smooth dimming range from minimum to maximum light levels. The device features a simple slide control lever, adjustable high-end and low-end trim-pots for customized dimming range, and constant memory to restore the previous light level after a power failure. It can be used in single-pole or three-way configurations and is suitable for multi-gang installations.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents