2. Rhino Rack
  3. RSWS
RSWS

Rhino Rack RSWS User manual

  • Hello! I've reviewed the user manual for the Rhino-Rack RSWS Spare Wheel Strap. This document provides instructions for installing the strap on a Rhino Pioneer or Alloy Tray, highlighting key features such as its 150kg lashing capacity and the importance of using non-stretch fasteners. I'm ready to assist with any questions you may have about the installation, safety precautions or any other topic within the scope of this document.
  • What is the lashing capacity of the spare wheel strap?
    Can the strap be used for lifting?
    What should be checked before using the spare wheel strap?
    What are the recommendations for fastening the spare wheel strap?
150kg lashing capacity on the polyester webbing. Must not be used for lifting. Always inspect prior to use. Protect
from friction and abrasion. Do not tie knots in webbing. Do not use strap if it is damaged.
Recommendations:
Use only non-stretch fastening ropes or straps. Do not overload your Rhino-Rack Pioneer/ Alloy Tray and roof bars. Check
your vehicle’s roof carrying capacity. Exercise caution when driving offroad as vehicle roof height has been increased.
Caution:
The handling characteristics of the vehicle change when you transport a load on the roof. For safety reasons, we
recommend exercising extreme care when transporting large wind-resisting loads; special consideration must be taken
into account when negotiating corners and under braking.
Note for Dealers and Fitters: It is your responsibility to ensure instructions are given to the end user or client.
Rhino-Rack
3 Pike Street, Rydalmere,
NSW 2116, Australia. Document No: R154 Fit Time: 10min
(Ph) (02) 9638 4744 Prepared By: Andy Wana Issue No: 04
(Fax) (02) 9638 4822 Authorised By: Chris Murty Issue Date: 16/01/2017
These instructions remain the property of Rhino-Rack Australia Pty. Ltd. and may not be used or changed for any other purpose than intended.
Page 1 of 3
Important Information
RSWS - Rhino Spare Wheel Strap
Important: Please read these instructions carefully prior to installation.
Check the contents of kit before commencing fi tment and report any discrepancies.
Clean the alloy tray prior to installation.
Place these instructions in the vehicle’s glove box after installation is complete.
Layout To suit Rhino Pioneer/ Alloy Tray
RSWS - Rhino Spare Wheel Strap
Page 2 of 3
Item Component Name Qty Part No.
1Spare Wheel Strap 3 Way 1 CA1085
2Strap 1.3m 3
3Fitting Instruction 1 R154
2
Parts List
Instructions
Tools Required: 13mm Spanner, Screwdriver (for leverage)
To be used with the Eye Bolt Kit 43178 (not included)
1
2
43117 (not included in this kit)
M10 Eye Bolt
Shakeproof Washer
OD38 Flat Washer
OD30 Flat Washer
1Assemble Hardware (43178 not included in this kit)
Assemble hardware as shown with the thread of the
eye bolt engaging only 2-3 turns.
Assembled
View M10 Plate Nut
Fit Eye Bolt to Plank
Lower the eye bolt assembly into the slot at the front of the plank as shown, the plate nut should be sitting
within the C channel of the plank. Slide the eye bolt along the plank to the desired position. Secure the eye
bolt in place by sliding a screwdriver through the eye of the bolt and rotate clockwise to tighten.
43178 (not included)
RSWS - Rhino Spare Wheel Strap
Page 3 of 3
3
4Position tyre up against 2 edges
Adjust 2 cam buckles to align the ring in the centre, then tighten via ratchet
TOP VIEW
/