Garmin B4 User manual

Instructions for Continued Airworthiness

for the Garmin G500H Installation in Eurocopter EC130

Garmin International, Inc.

1200 E. 151st Street

Olathe, Kansas 66062 USA

Dwg. Number:

190-01527-15 Rev. 1

Rev.

Date

Description of Change

1

04/22/2014

Initial release.

Note: Document was RSG P/N 16E08310001 Rev. E

Confidential

This drawing and the specifications contained herein

are the property of Garmin Ltd. or its subsidiaries and

may not be reproduced or used in whole or in part as

the basis for manufacture or sale of products without

written permission.

Instructions for Continued Airworthiness 190-01527-15 Rev 1

for the Garmin G500H Installation in Eurocopter EC130 Page 2 of 82

Table of Contents

CHAPTER 1 .................................................................................................................................. 4

Section 01-00-00

Introduction ......................................................................................................... 4

CHAPTER 4 .................................................................................................................................. 5

Section 04-00-00

Airworthiness Limitations .................................................................................. 5

CHAPTER 5 .................................................................................................................................. 6

Section 05-00-00

Continued Airworthiness Inspections ................................................................ 6

Section 05-20-10

Continued Airworthiness Scheduled Inspections .............................................. 9

Section 05-20-20

Continued Airworthiness Special Inspections ................................................... 17

CHAPTER 6 .................................................................................................................................. 19

Section 06-00-00

Dimensions and Access ....................................................................................... 19

CHAPTER 8 .................................................................................................................................. 27

Section 8-00-00

Weight and Balance Information ........................................................................ 27

CHAPTER 11 ................................................................................................................................ 28

Section 11-00-00

Placards and Markings ........................................................................................ 28

CHAPTER 12 ................................................................................................................................ 30

Section 12-00-00

Servicing Maintenance Practices ........................................................................ 30

Section 12-10-00

Return-to-Service Practices ................................................................................ 31

Section 12-20-00

Calibration Requirements ................................................................................... 32

CHAPTER 20 ................................................................................................................................ 33

Section 20-00-00

Standard Practices ............................................................................................... 33

Section 20-10-00

Torques Maintenance Practices .......................................................................... 34

Section 20-30-00

Painting Maintenance Practices .......................................................................... 38

Section 20-40-00

Corrosion Control Maintenance Practices .......................................................... 39

Section 20-90-00

Dye Penetrant Inspection Methods ..................................................................... 42

CHAPTER 31 ................................................................................................................................ 43

Section 31-00-00

Instruments ......................................................................................................... 43

CHAPTER 98 ................................................................................................................................ 68

Instructions for Continued Airworthiness 190-01527-15 Rev 1

for the Garmin G500H Installation in Eurocopter EC130 Page 3 of 82

Section 98-00-00

Wiring Diagrams and Pitot-Static System Schematics ....................................... 68

Section 98-10-00

Wiring Diagrams .................................................................................................. 69

Section 98-20-00

Pitot-Static System Schematic ............................................................................. 82

Instructions for Continued Airworthiness 190-01527-15 Rev 1

for the Garmin G500H Installation in Eurocopter EC130 Page 4 of 82

CHAPTER 1

Section 01-00-00 Introduction

These are accepted Instructions for Continued Airworthiness for modifications performed in

accordance with Eurocopter EC130 B4 Garmin G500H Flight Display System Installation STC. All

references to the G500H in this document will refer to the Garmin G500H Flight Display System

Installation and other related components specified in these Instructions for Continued

Airworthiness (ICA). A STC permission letter and Instructions for Continued Airworthiness (ICA)

should be supplied to the owner/operator of the STC at the time of completion. Subsequent

accepted changes to the ICA will be distributed to owners and operators of the STC.

This Instructions for Continued Airworthiness is intended to supplement the Model EC130 B4

rotorcraft maintenance manuals provided by Eurocopter. The information, procedures,

requirements, and limitations contained in this Instructions for Continued Airworthiness for this

type design change supersedes the information, procedures, requirements, and limitations

contained in the rotorcraft’s maintenance manual when the type design change is installed on

the Type Certificate Holder’s rotorcraft.

01-00-00

Instructions for Continued Airworthiness 190-01527-15 Rev 1

for the Garmin G500H Installation in Eurocopter EC130 Page 5 of 82

CHAPTER 4

Section 04-00-00 Airworthiness Limitations

There are no additional Airworthiness Limitations as defined in 14 CFR Part 27, Appendix A.

A27.4 that result from this modification. The Airworthiness Limitations section is FAA approved

and specifies inspections and other maintenance required under 14 CFR §§ 43.16 and 91.403

of the Federal Aviation Regulations unless an alternative program has been FAA approved.

04-00-00

Instructions for Continued Airworthiness 190-01527-15 Rev 1

for the Garmin G500H Installation in Eurocopter EC130 Page 6 of 82

CHAPTER 5

Section 05-00-00 Continued Airworthiness Inspections

1. General

This chapter contains time limit intervals for the Component Overhaul Schedule and Scheduled

Inspections for the G500H Installation. This chapter is to be added to the approved scheduled

inspection for the rotorcraft.

2. Component Overhaul Schedule

The system does not require overhaul at a specific time period. Power on self-test and

continuous BIT will monitor the health of the G500H system. If any LRU indicates an internal

failure, the unit may be removed and replaced.

3. Scheduled Inspections Overview

The G500H Installation requires a 90 Day Inspection that must be performed 90 days after

installation and then afterwards within 90 days of the last G500H Installation 90 day inspection.

The 90 Day Inspection requirements are specified in Table 5-01.

The G500H Installation requires an Annual Inspection that must be performed within 1 year (12

months) of initial installation and then afterwards within 1 year (12 months) of the last G500H

Installation annual inspection. The annual inspection requirements are specified in Table 5-02.

The G500H Installation requires a 5 Year Inspection that must be performed within 60 months

of initial installation and then afterwards within 60 months of the last G500H Installation

inspection. The 5 Year Inspection requirements are specified in Table 5-03.

The G500H Installation requires a 10 Year/2000 Flight Hours Inspection that must be performed

within 120 months or 2000 flight hours, whichever occurs first, of initial installation and then

afterwards within 120 months or 2000 flight hours, whichever occurs first, of the last G500H

Installation 10 year/2000 flight inspections. The 10 Year/2000 Flight Hour Inspection

requirements are specified in Table 5-04.

4. Special Inspection Practices

Conditions may arise from incidents or accidents that may warrant additional inspection

requirements. A Special Inspection is required if the aircraft is involved in a hard landing or is

subjected to total immersion in water. If either of these conditions occurs, the G500H

Installation must be inspected using the same procedures called out in the Annual Inspection

Procedures in Table 5-02.

05-00-00

Instructions for Continued Airworthiness 190-01527-15 Rev 1

for the Garmin G500H Installation in Eurocopter EC130 Page 7 of 82

The G500H Installation has a Post-Lightning Strike Inspection that must be performed in the

event of a suspected or actual lightning strike to the aircraft. The Post-Lightning Strike

Inspection requirements are specified in Table 5-05.

5. Definitions and Acronyms

The following is short descriptions of words and terms used in the procedures for the required

scheduled inspections.

• Examine – Look carefully to find the condition of the component. Find how that condition

is related to a specific standard.

• Condition – The state of an item or component compared to a known standard.

• Standard – A specified rule or measure that is used to find the condition of a component.

• Damage – Physical deterioration of a component.

• Inspection – A procedure that includes checking, inspecting, and examining a system or

component.

• Scheduled Inspection – An inspection procedure that must occur at a specified calendar

interval or at specified operational time intervals. Scheduled Inspections are required to

help ensure the rotorcraft stays airworthy.

• Maintenance – The servicing and / or repair of a rotorcraft, a system, or a component that

keeps it serviceable.

• Security – Term used for inspection of hardware and components to make sure they are

properly attached and tightened.

Acronyms

FOV-

Field of View

ICA-

Instructions for Continued Airworthiness

PFD-

Primary Flight Display

MFD-

Multifunction Display

VOM-

Volt Ohm Meter

GDC-

Garmin Data Computer

GRS-

Garmin Reference System

GMU-

Garmin Magnetometer Unit

GDU-

Garmin Display Unit

05-00-00

Instructions for Continued Airworthiness 190-01527-15 Rev 1

for the Garmin G500H Installation in Eurocopter EC130 Page 8 of 82

OAT-

Outside Air Temperature

GTP-

Garmin Temperature Probe

ADC-

Air Data Computer

STC-

Supplemental Type Certificate

AHRS-

Attitude Heading Reference System

05-00-00

Instructions for Continued Airworthiness 190-01527-15 Rev 1

for the Garmin G500H Installation in Eurocopter EC130 Page 9 of 82

Section 05-20-10 Continued Airworthiness Scheduled Inspections

1. General

This section contains requirements for scheduled inspections. Also included is a list of special

tools required to perform the scheduled inspections. If any part of the installation appears to

be functioning improperly, consult the troubleshooting guide. If a major component is

damaged or continues to malfunction, the component in question should be returned to the

manufacturer for replacement.

2. Scheduled Inspection Program

The G500H Installation requires scheduled inspections in order to maintain continued

airworthiness. Every effort should be made to perform the inspections with the aircraft placed

in a clean well lit environment. There are four different scheduled inspections required for the

G500H Installation.

a) 90 Day Inspection

The 90 day inspection is required to be performed every 90 day period of calendar elapsed

time, regardless of hours of operation. Inspection Table 5-01 the requirements of the 90 day

inspection.

b) 1 Year (Annual) Inspection

The 1 year (annual) inspection is required to be performed every 1 year period of calendar

elapsed time, regardless of hours of operation. Inspection Table 5-02 the requirements of the

1 year (annual) inspection.

c) 5 Year Inspection

The 5 year inspection is required to be performed every 5 year period of calendar elapsed

time, regardless of hours of operation. Inspection Table 5-03 the requirements of the 5 year

inspection

d) 10 Year / 2000 Flight Hours

The 10 year /2000 Flight Hour inspection is required to be performed at a 10 year period of

calendar elapsed time, or at 2000 flight hours of operation, whichever occurs first. Inspection

Table 5-04 specifies the requirements of the 10 year/2000 flight hour inspection.

3. Tools and Special Tools for Scheduled Inspection

Although not necessarily considered special tools, the adjustable ball swivel mirror and bright

flashlight and / or drop light are standard requirements for doing inspections. These items

should be used freely and frequently to enhance inspection quality and help ensure

05-20-10

Instructions for Continued Airworthiness 190-01527-15 Rev 1

for the Garmin G500H Installation in Eurocopter EC130 Page 10 of 82

discrepancies are not missed. It is important to have adequate lighting for all phases of the

inspection

.

The special tools necessary for the G500H inspection are listed as follows:

a) Milliohm meter (for electrical bonding testing).

Table 5-01 -90 Day Inspection

Registration No.

Serial No.

Helicopter Total Hours

90 Day Scheduled Inspection

• The 90 Day Inspection shall be accomplished at least at an interval of once every 90 days of

elapsed calendar time.

• Initial each item after accomplishing the inspection.

• Record all findings and attach a copy of findings to this inspection form.

• After correction of all findings, make maintenance record entry.

90 Day Pre-inspection

Requirement

Initial

1. Review Airworthiness Directives.

90 Day Inspection

Requirement

Initial

GDC 74H ADC

1. Access GDC 74H (reference Section 6-00-00- Dimensions and Access). Drain the pitot-

static system by removing the safety wire, nut and plug.

2. Re-install the plug, nut and safety wire.

3. Reference Section 12-10-00 Return-to-Service Practices for the GDC 74H

05-20-10

Instructions for Continued Airworthiness 190-01527-15 Rev 1

for the Garmin G500H Installation in Eurocopter EC130 Page 11 of 82

Table 5-02 -1 year (Annual) Inspection

Registration No.

Serial No.

Helicopter Total Hours

1 Year (Annual) Scheduled Inspection

• The 1 Year inspection shall be accomplished at least at an interval of once every year of elapsed

calendar time.

• Initial each item after accomplishing the inspection.

• Record all findings and attach a copy of findings to this inspection form.

• After correction of all findings, make maintenance record entry.

1 year (Annual) Pre-inspection

Requirement

Initial

1. Review Airworthiness Directives.

1 year (Annual) Inspection

Requirement

Initial

GDU 620

1. Locate GDU 620 (reference Section 6-00-00 Access and Dimension). Inspect all knobs

and buttons for legibility.

2. Inspect instrument panel for damage, corrosion, and security. If damaged, replace

damaged or cracked Instrument panel. Treat and repair corrosion as required in Section

20-40-00 Corrosion Control Maintenance Practices. Tighten any loose hardware to values

listed in Section 20-10-00.

3. Inspect unit for security of attachment. Replace the damaged or corroded hardware.

Replace any missing hardware. Torque all screws in accordance with Section 20-10-00

Torques Maintenance Practice.

4. Conduct visual inspection of wires, backshells, and connectors looking for signs of wear,

deterioration or damage. Replace as required.

5. Inspect harness connections in back of unit. Secure any loose connections and support

unsecure wiring harness with additional clamping and / or tie rap supports if required.

GRS 77H AHRS

1. Access GRS 77H (reference Section 6-00-00- Dimensions and Access). Inspect AHRS and

mount for physical damage cracks, and corrosion. Treat and repair corrosion as required in

Section 20-40-00 Corrosion Control Maintenance Practices.

05-20-10

Instructions for Continued Airworthiness 190-01527-15 Rev 1

for the Garmin G500H Installation in Eurocopter EC130 Page 12 of 82

2. Conduct visual inspection of wires, backshells, and connectors looking for signs of wear,

deterioration or damage. Replace as required.

3. Inspect harness connections in back of unit. Secure any loose connections and support

unsecure wiring harness with additional clamping and / or tie rap supports if required.

4. Inspect unit for security of attachment. Replace the damaged or corroded hardware.

Replace any missing hardware. Torque all screws in accordance with Section 20-10-00

Torques Maintenance Practice.

GMU 44 Magnetometer Installation

1. Access GMU 44 (reference Section 6-00-00- Dimensions and Access). Inspect GMU 44

and mount for physical damage cracks, and corrosion. Treat and repair corrosion as

required in Section 20-40-00 Corrosion Control Maintenance Practices.

2. Conduct visual inspection of wires, backshells, and connectors looking for signs of wear,

deterioration or damage. Replace as required.

3. Inspect hardware. Replace the damaged or corroded hardware. Replace any missing

hardware. Torque all screws in accordance with Section 20-10-00 Torques Maintenance

Practice.

4. Inspect harness connections in back of unit. Secure any loose connections and support

unsecure wiring harness with additional clamping and / or tie rap supports if required.

Shelf Installation

1. Access Shelf Installation (reference Section 6-00-00- Dimensions and Access). Inspect for

physical damage cracks, and corrosion. Treat and repair corrosion as required in Section 20-

40-00 Corrosion Control Maintenance Practices

2. Inspect hardware. Replace the damaged or corroded hardware. Replace any missing

hardware. Torque all screws in accordance with Section 20-10-00 Torques Maintenance

Practice.

GDC 74H ADC Installation

1. Access GDC 74H (reference Section 6-00-00- Dimensions and Access). Inspect GDC 74H

and mount for physical damage cracks, and corrosion. Treat and repair corrosion as

required in Section 20-40-00 Corrosion Control Maintenance Practices.

2. Inspect unit for security of attachment. Replace the damaged or corroded hardware.

Replace any missing hardware. Torque all screws in accordance with Section 20-10-00

Torques Maintenance Practice.

3. Conduct visual inspection of wires, backshells, and connectors looking for signs of wear,

deterioration or damage. Replace as required.

4. Inspect harness connections in back of unit. Secure any loose connections and support

unsecure wiring harness with additional clamping and / or tie rap supports if required.

5. Inspect Pitot-Static System for damage. Replace parts as needed. Complete the 90 Day

Inspection found in Table 5-01.

05-20-10

Instructions for Continued Airworthiness 190-01527-15 Rev 1

for the Garmin G500H Installation in Eurocopter EC130 Page 13 of 82

GTP 59 OAT Probe Installation

1. Access GTP 59 OAT Probe (reference Section 6-00-00- Dimensions and Access). Inspect

GTP 59 OAT and mount for physical damage cracks, and corrosion. Treat and repair

corrosion as required in Section 20-40-00 Corrosion Control Maintenance Practices.

2. Inspect harness connections in back of unit. Secure any loose connections and support

unsecure wiring harness with additional clamping and / or tie rap supports if required.

3. Inspect unit for security of attachment. Replace the damaged or corroded hardware.

Replace any missing hardware. Torque all screws in accordance with Section 20-10-00

Torques Maintenance Practice.

Terminal Block Installation

1. Access Terminal Block Installation (reference Section 6-00-00- Dimensions and Access).

Inspect installation for physical damage cracks, and corrosion. Treat and repair corrosion as

required in Section 20-40-00 Corrosion Control Maintenance Practices.

2. Inspect unit for security of attachment. Replace the damaged or corroded hardware.

Replace any missing hardware. Torque all screws in accordance with Section 20-10-00

Torques Maintenance Practice.

Cooling Fan Installation (If option is installed)

1. Access Cooling Fan Installation (reference Section 6-00-00 Dimensions and Access).

Inspect installation for physical damage, cracks, and corrosion. Treat and repair corrosion as

required in Section 20-40-00 Corrosion Control Maintenance Practices.

2. Inspect cooling fan hoses for physical damage and security. Repair or replace any

damaged hoses. Replace any damaged or missing Tywraps

3. Inspect unit for security of attachment. Replace the damaged or corroded hardware.

Replace any missing hardware. Torque all screws in accordance with Section 20-10-00

Torques Maintenance Practices.

05-20-10

Instructions for Continued Airworthiness 190-01527-15 Rev 1

for the Garmin G500H Installation in Eurocopter EC130 Page 14 of 82

Table 5-03 -5 Year Inspection

Registration No.

Serial No.

Helicopter Total Hours

5 Year Scheduled Inspection

• The 5 Year Inspection shall be accomplished at least at an interval of once every 5 years of

elapsed calendar time.

• Initial each item after accomplishing the inspection.

• Record all findings and attach a copy of findings to this inspection form.

• After correction of all findings, make maintenance record entry.

5 Year Pre-inspection

Requirement

Initial

1. Review Airworthiness Directives.

5 Year Inspection

Requirement

Initial

GRS 77H AHRS

1. The GRS 77 utilizes an Earth magnetic field model which is updated once every five years

as part of the Aviation Database maintained by the owner/operator. If the magnetic model

is not current, the unit will issue an alert upon startup indicating the model has expired. The

model can be updated by inserting an aviation database card with an updated IGRF model

and powering on the system. A prompt will direct the user to press ENT to update the

model.

05-20-10

Instructions for Continued Airworthiness 190-01527-15 Rev 1

for the Garmin G500H Installation in Eurocopter EC130 Page 15 of 82

Table 5-04 -10 Year/2000 Flight Hour Inspection

Registration No.

Serial No.

Helicopter Total Hours

10 Year/ 2000 Flight Hour Scheduled Inspection

• The 10 Year/ 2000 Flight Hour Inspection shall be accomplished at least at an interval of once

every 10 years of elapsed calendar time or 2000 Flight Hours, whichever occurs first.

• Initial each item after accomplishing the inspection.

• Record all findings and attach a copy of findings to this inspection form.

• After correction of all findings, make maintenance record entry.

10 Year/2000 Flight Hour Pre-inspection

Requirement

Initial

1. Review Airworthiness Directives.

10 Year/2000 Flight Hour Inspection

Requirement

Initial

GRS 77H AHRS

1. Access GRS 77H, (Reference Section 6-00-00 Dimensions and Access) and disconnect all

harness connectors.

2. Measure the resistance between the GRS 77H and a nearby exposed portion of aircraft

metallic structure. Verify that the resistance is less than or equal to 20 milliohms. If greater

must be restored to the value specified in the G500H STC Installation Manual.

3. Reconnect all disconnected harness connectors and ensure they are secure.

GDU 620

4. Access GDU 620, (Reference Section 6-00-00 Dimensions and Access) and disconnect all

harness connectors.

5. Measure the resistance between the GDU 620 and a nearby exposed portion of aircraft

metallic structure. Verify that the resistance is less than or equal to 40 milliohms. If greater

must be restored to the value specified in the G500H STC Installation Manual.

6. Reconnect all disconnected harness connectors and ensure they are secure.

05-20-10

Instructions for Continued Airworthiness 190-01527-15 Rev 1

for the Garmin G500H Installation in Eurocopter EC130 Page 16 of 82

GDC 74H ADC

7. Access GDC 74H, (Reference Section 6-00-00 Dimensions and Access) and disconnect all

harness connectors.

8. Measure the resistance between the GDC 74H and a nearby exposed portion of aircraft

metallic structure. Verify that the resistance is less than or equal to 20 milliohms. If greater

must be restored to the value specified in the G500H STC Installation Manual.

9. Reconnect all disconnected harness connectors and ensure they are secure.

GMU 44

10. Access GMU 44, (Reference Section 6-00-00 Dimensions and Access) and disconnect all

harness connectors.

11. Measure the resistance between the GMU 44 and a nearby exposed portion of aircraft

metallic structure. Verify that the resistance is less than or equal to 20 milliohms. If greater

must be restored to the value specified in the G500H STC Installation Manual.

12. Reconnect all disconnected harness connectors and ensure they are secure.

GTP 59

13. Access GTP 59, (Reference Section 6-00-00 Dimensions and Access) and disconnect all

harness connectors.

14. Measure the resistance between the GTP 59 and a nearby exposed portion of aircraft

metallic structure. Verify that the resistance is less than or equal to 5 milliohms. If greater

must be restored to the value specified in the G500H STC Installation Manual.

15. Reconnect all disconnected harness connectors and ensure they are secure.

4. Post Inspection Maintenance Practices

After completion of the 1 Year (Annual) Inspection, 5 Year Inspection and 10 Year/2000 Flight

Hour Inspection and all discrepancies found have been corrected, the Return-to-Service

Practices (Reference Section 12-00-00 Return-to-Service Practices) should be accomplished in

preparation for returning the rotorcraft to service

05-20-10

Instructions for Continued Airworthiness 190-01527-15 Rev 1

for the Garmin G500H Installation in Eurocopter EC130 Page 17 of 82

Section 05-20-20 Continued Airworthiness Special Inspections

1. General

This section contains requirements for special inspections. Also included is a list of special tools

required to perform the scheduled inspections. If any part of the installation appears to be

functioning improperly, consult the troubleshooting guide. If a major component is damaged or

continues to malfunction, the component in question should be returned to the manufacturer

for replacement.

2. Special Inspection Program

Conditions may arise from incidents or accidents that may warrant additional inspection

requirements. A Special Inspection is required if the aircraft is involved in a hard landing or is

subjected to total immersion in water. If either of these conditions occurs, the G500H

Installation must be inspected using the same procedures called out in the Annual Inspection

Procedures in Table 5-02.

The G500H Installation has a Post-Lightning Strike Inspection that must be performed in the

event of a suspected or actual lightning strike to the aircraft. The Post-Lightning Strike

Inspection requirements are specified in Table 5-05.

3. Tools and Special Tools for Special Inspections

Although not necessarily considered special tools, the adjustable ball swivel mirror and bright

flashlight and / or drop light are standard requirements for doing inspections. These items

should be used freely and frequently to enhance inspection quality and help ensure

discrepancies are not missed. It is important to have adequate lighting for all phases of the

inspection

.

The special tools necessary for the G500H inspection are listed as follows:

a) Milliohm meter (for electrical bonding testing).

05-20-20

Instructions for Continued Airworthiness 190-01527-15 Rev 1

for the Garmin G500H Installation in Eurocopter EC130 Page 18 of 82

Table 5-05 -Post-Lightning Strike Inspection

Registration No.

Serial No.

Helicopter Total Hours

Post-Lightning Strike Inspection

• The Post-Lightning Strike Inspection shall be accomplished in the event of a suspected or actual

lightning strike to the aircraft.

• Initial each item after accomplishing the inspection.

• Record all findings and attach a copy of findings to this inspection form.

• After correction of all findings, make maintenance record entry.

Post-Lightning Strike Pre-inspection

Requirement

Initial

1. Review Airworthiness Directives.

Post-Lightning Strike Inspection

Requirement

Initial

GTP 59 OAT Probe Installation

1. Access the GTP 59 OAT Probe Installation. Reference Section 6-00-00 Dimensions and

Access.

2. Inspect the probe and the doubler (P/N: 115-01812-00) for signs of structural damage. If

there are visible signs of damage, replace the parts as needed.

Post-Lightning Strike Post- Inspection

Requirement

Initial

1. Verify that the OAT is displayed on the GDU 620 PFD normally.

05-20-20

Instructions for Continued Airworthiness 190-01527-15 Rev 1

for the Garmin G500H Installation in Eurocopter EC130 Page 19 of 82

CHAPTER 6

Section 06-00-00 Dimensions and Access

1. Access Methods

For removal and installation of specific components, reference Section 31-00-00 Instruments,

Removal and Replacement

a) GMU 44, Magnetometer

Magnetometer is located in the tail boom between TB 868 and 1578. (Figure 6-01)

Access Methods

i. Removal

1. Un-latch and open the battery door on the left side of the aircraft.

2. If a battery is installed it may be necessary to remove the battery to gain access to

the magnetometer. Consult the manufacturers Installation and removal

instructions for proper removal of unit.

ii. Installation

1. Re-install battery if removed to gain access to the magnetometer. Consult the

manufacturers Installation and Removal instructions for proper installation of unit.

2. Close the battery access door and latch it.

Caution: Use of power tools during removal or installation of

panels and attaching hardware may damage nut plates or

deform holes in composite doors, covers, panels, and fairings.

06-00-00

Figure 6-01

GMU 44

TB

868

REF

TB

1578

REF

Instructions for Continued Airworthiness 190-01527-15 Rev 1

for the Garmin G500H Installation in Eurocopter EC130 Page 20 of 82

b) GDC 74H, Air Data Computer

GDC 74H is located underneath the cabin floor between station 2249 and 2737 on the left

side of the aircraft. (Figure 6-02)

Access Methods

i. Removal

1. Un-latch the Center lower belly access panel.

2. Disconnect the retaining straps that prevent the panel from falling to the floor.

3. If aftermarket items are attached to the Center lower belly panel it may be

necessary to remove or disconnect them in order to remove the lower belly panel.

Consult the manufacturers Installation and Removal instructions for proper

removal of items.

ii. Installation

1. Re-install aftermarket items if removed to gain access to the air data computer.

Consult the manufacturers Installation and Removal instructions for proper

installation of items.

2. Connect the retaining strap that was disconnected to gain access to the air data

computer.

3. Close the Center lower belly access panel and latch it.

Caution: Use of power tools during removal or installation

of panels and attaching hardware may damage nut plates

or deform holes in composite doors, covers, panels, and

fairings.

06-00-00

Figure 6-02

GDC 74H

STA

2249

REF

STA

2737

REF

Page is loading ...

Garmin B4 User manual

This manual is also suitable for

Garmin B4 User manual

Related papers

Other documents