Knoll HDP2300 User manual

Category
Projectors
Type
User manual

This manual is also suitable for

HDP2300 High Definition Projector
PROJECTOR
Users Manual
Copyright
This publication, including all photographs, illustrations and software, is protected under international copy-
right laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be
reproduced without written consent of the author.
© Copyright 2010
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no represen-
tations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of
merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publi-
cation and to make changes from time to time in the content hereof without obligation of the manufacturer to
notify any person of such revision or changes.
Trademark Recognition
Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pend-
ing applications in other countries throughout the world.
All other product names used in this manual are the properties of their respective owners and are acknowl-
edged.
i
HDP2300 Users Manual
ii
Important Safety Information
Important:
It is strongly recommended that you read this section carefully before using the projector. These
safety and usage instructions will ensure that you enjoy many years of safe use of the projector.
Keep this manual for future reference.
Symbols Used
Warning symbols are used on the unit and in this manual to alert you of hazardous situations.
The following styles are used in this manual to alert you to important information.
Note:
Provides additional information on the topic at hand.
Important:
Provides additional information that should not be overlooked.
Caution:
Alerts you to situations that may damage the unit.
Warning:
Alerts you to situations that may damage the unit, create a hazardous environment, or cause per-
sonal injury.
Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this
example:
“Push the MENU button on the remote control to open the DISPLAY menu.”
General Safety Information
¾ Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in the
unit. For servicing, contact qualified service personnel.
¾ Follow all warnings and cautions in this manual and on the unit case.
¾
The projection lamp is extremely bright by design. To avoid damage
to eyes, do not look into the lens
when the lamp is on.
¾ Do not place the unit on an unstable surface, cart, or stand.
¾ Avoid using the system near water, in direct sunlight, or near a heating device.
¾
Do not place heavy objects such as books or bags on the unit.
Preface
Projector Installation Notice
¾ Place the projector in a horizontal position
The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in
any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically.
¾ Allow at least 50 cm clearance around the exhaust vent.
¾ Ensure that the intake vents do not recycle hot air from the exhaust vent.
¾
When operating the projector in an enclosed space, ensure that the surrounding air temperature
within the en
closu
r
e d
o
es not exceed operating temperature while the projector is running, and the
air intake and exhaust vents are unobstructed.
¾ All enclosures should pass a certified thermal evaluation to ensure that the projector does
not recycle
exhaust air, as this may cause the device to shutdown even if the enclosure temperature is with the
acceptable operating temperature range.
Power Safety
¾ Only use the supplied power cord.
¾
Do not place anything on the power cord. Place the power cord where it will not be in the way of foot
traffic
.
¾
Rem
o
ve the batteries from the remote control when storing or not in use for a prolonged period.
iii
Replacing the Lamp
Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 35 for
clear and safe instructions for this procedure. Before replacing the lamp:
¾ Unplug the power cord.
¾
Allow the lamp to cool for about one hour.
Cleaning the Projector
¾ Unplug the power cord before cleaning. See Cleaning the Projector on page 37.
¾
Allow the lamp to cool for about one hour.
Regulatory Warnings
Before installing and using the projector, read the regulatory notices in the Regulatory Compliance section
on page 50.
Important Recycle Instructions:
Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can
be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws.
For more information, contact the Electronic Industries Alliance at
WWW.EIAE.ORG
. For lamp specific
disposal information check WWW.LAMPRECYCLE.ORG
.
Symbol Explanations
DISPOSAL: Do not use household or municipal waste collection services for
disposal of electrical and electronic equipment. EU countries require the use
of separate recycling collection services.
About this manual
This manual is intended for end users and describes how to install and operate the DLP projector. Wherever
possible, relevant information—such as an illustration and its description—has been kept on one page. This
printer-friendly format is both for your convenience and to help save paper, thereby protecting the environ-
ment. It is suggested that you only print sections that are relevant to your needs.
iv
HDP2300 Users Manual
v
Table of Contents
GETTING STARTED.......................................................................................................................................................... 1
PACKING CHECKLIST ........................................................................................................................................................... 1
VIEWS OF PROJECTOR PARTS............................................................................................................................................... 2
HDP2300 Series Front-right View.................................................................................................................................. 2
Top view—On-screen Display (OSD) buttons and LEDs ............................................................................................... 4
Rear view ........................................................................................................................................................................ 5
Bottom view..................................................................................................................................................................... 7
REMOTE CONTROL PARTS ................................................................................................................................................... 8
REMOTE CONTROL OPERATING RANGE............................................................................................................................. 10
PROJECTOR AND REMOTE CONTROL BUTTONS.................................................................................................................. 10
SETUP AND OPERATION............................................................................................................................................... 11
INSERTING THE REMOTE CONTROL BATTERIES ................................................................................................................. 11
CONNECTING INPUT DEVICES ............................................................................................................................................ 12
INSTALLING OR REMOVING THE OPTIONAL LENS .............................................................................................................. 13
Removing the Existing Lens From the Projector .......................................................................................................... 13
Installing the New Lens................................................................................................................................................. 14
STARTING AND SHUTTING DOWN THE PROJECTOR............................................................................................................. 15
Starting the projector.................................................................................................................................................... 15
Shutting down the Projector ......................................................................................................................................... 16
ADJUSTING THE PROJECTOR LEVEL ................................................................................................................................... 17
ADJUSTING PROJECTED IMAGE POSITION USING SHIFT...................................................................................................... 18
Adjusting the vertical image position............................................................................................................................ 18
Adjusting the horizontal image position ....................................................................................................................... 19
Shift Range Diagram ..................................................................................................................................................... 19
ADJUSTING THE ZOOM RING, FOCUS AND KEYSTONE ........................................................................................................ 20
ON-SCREEN DISPLAY (OSD) MENU SETTINGS....................................................................................................... 21
OSD MENU CONTROLS ..................................................................................................................................................... 21
Navigating the OSD ...................................................................................................................................................... 21
SETTING THE OSD LANGUAGE .......................................................................................................................................... 22
OSD MENU OVERVIEW ..................................................................................................................................................... 23
PICTURE: BASIC MENU ................................................................................................................................................... 24 U
PICTURE: ADVANCED MENU........................................................................................................................................... 25 U
HSG Adjustment............................................................................................................................................................ 26
ViviSettings ................................................................................................................................................................... 26
DISPLAY MENU............................................................................................................................................................... 27
PC Detail Adjustment.................................................................................................................................................... 28
SYSTEM SETUP: BASIC MENU ....................................................................................................................................... 29 U
Menu Settings................................................................................................................................................................ 30
Source ........................................................................................................................................................................... 30
SYSTEM SETUP: ADVANCED MENU............................................................................................................................... 31
Lamp ............................................................................................................................................................................. 32
HDMI............................................................................................................................................................................ 32
Closed Caption.............................................................................................................................................................. 33
12V OUT A.................................................................................................................................................................... 33
INFORMATION MENU.................................................................................................................................................... 34
MAINTENANCE AND SECURITY................................................................................................................................. 35
REPLACING THE PROJECTION LAMP................................................................................................................................... 35
CLEANING THE PROJECTOR................................................................................................................................................ 37
Cleaning the Lens ......................................................................................................................................................... 37
Cleaning the Case ......................................................................................................................................................... 37
USING THE PHYSICAL LOCK .............................................................................................................................................. 38
Using the Kensington
®
Lock ......................................................................................................................................... 38
Using the Security Chain Lock...................................................................................................................................... 38
Preface
vi
TROUBLESHOOTING ..................................................................................................................................................... 39
C
OMMON PROBLEMS AND SOLUTIONS ............................................................................................................................... 39
TIPS FOR TROUBLESHOOTING ............................................................................................................................................ 39
LED ERROR MESSAGES..................................................................................................................................................... 40
IMAGE PROBLEMS.............................................................................................................................................................. 41
LAMP PROBLEMS ............................................................................................................................................................... 41
REMOTE CONTROL PROBLEMS .......................................................................................................................................... 42
HAVING THE PROJECTOR SERVICED .................................................................................................................................. 42
HDMI Q & A………………………………………………………………………………………………………………43
SPECIFICATIONS............................................................................................................................................................. 44
SPECIFICATIONS................................................................................................................................................................. 44
PROJECTION DISTANCE VS. PROJECTION SIZE.................................................................................................................... 45
HDP2300 Series Projection Distance and Size Table .................................................................................................. 45
HDP2300 SERIES TIMING MODE TABLE............................................................................................................................ 46
PROJECTOR DIMENSIONS ................................................................................................................................................... 49
REGULATORY COMPLIANCE ..................................................................................................................................... 50
FCC WARNING .................................................................................................................................................................. 50
CANADA ............................................................................................................................................................................ 50
SAFETY CERTIFICATIONS ................................................................................................................................................... 50
EN 55022 WARNING ......................................................................................................................................................... 50
HDP2300 Users Manual
1
G
ETTING
S
TARTED
Packing Checklist
Carefully unpack the projector and check that the following items are included:
HDP2300 SERIES PROJECTOR WITH LENS CAP
R
EMOTE CONTROL
(WITH
TWO
AA
BATTERIES)
VGA CABLE COMPONENT CABLE POWER CORD
HDMI
CABLE CD-ROM
(T
HIS USERS MANUAL)
W
ARRANTY CARD QUICK START GUIDE
Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. It
is recommend that you keep the original packing material should you ever need to return the equipment
for warranty service.
Caution:
Avoid using the projector in dusty environments.
HDP2300 Users Manual
Views of Projector Parts
HDP2300 Series Front-right View
ITEM LABEL DESCRIPTION SEE PAGE:
1.
IR receiver Receives IR signal from remote control
8
2.
Lens Projection Lens
3.
Focus ring Focuses the projected image
4.
Zoom ring Enlarges the projected image
18
5.
Height adjuster Adjusts level of projector
17
6.
Function keys
See Top view—On-screen Display (OSD) buttons
and LEDs.
4
7.
Lamp cover Removes cover to replace lamp or color wheel
35
8.
Vertical lens shift Adjusts the image position vertically
18
– 2 –
HDP2300 Users Manual
3
ITEM LABEL DESCRIPTION SEE PAGE:
9.
Horizontal lens shift Adjusts the image position horizontally
19
10.
Lens release button Press the release button before removing the lens
13
Important:
Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp
cool. Do not obstruct any of the ventilation openings.
HDP2300 Users Manual
Top view—On-screen Display (OSD) buttons and LEDs
ITEM LABEL DESCRIPTION
SEE
PAGE:
1.
MENU Opens and exits OSD menus
2.
(Up cursor) /
Keystone+
Navigates and changes settings in the OSD
Quick Menu – For Keystone
3.
ENTER Enter or confirm highlighted OSD menu item
21
4.
BLANK Displays a blank screen and mutes audio
5.
(Left cursor) Navigates and changes settings in the OSD
21
6.
AUTO Optimizes image size, position, and resolution
7.
(Right cursor) Navigates and changes settings in the OSD
8.
(Down cursor) /
Keystone-
Navigates and changes settings in the OSD
Quick Menu – For Keystone
21
9.
SOURCE Enter the Source menu
12
– 4 –
HDP2300 Users Manual
Rear view
ITEM LABEL DESCRIPTION SEE PAGE:
1.
VIDEO Connect the composite cable from a video device
2.
YPbPr Connect a component video enabled device
3.
HDMI 1/ 2/ 3 Connect the HDMI CABLE from a HDMI device
4.
USB Connect the USB cable from a computer
12
5.
IR receiver Receive IR signal from remote control
8
Red Error code
Lamp is not ready (warming up/shutting
down/cooling)
(see LED Error Messages on page
6.
LAMP LED
Flashing
40)
5
7.
TEMP LED Red Error code
40
Orange Standby
Green In normal operation
8.
PWR LED
Flashing Powering on/ cooling
Turns the projector on or off (main power switch must be
turned on first).
Press to place the projector in standby mode.
15
9.
POWER
12
10.
RS-232C Connects RS-232 serial port cable for remote control
When connected to the screen through a commercially avail-
able cable, the screen deploys automatically on start up of
the projector. The screen retracts when the projector is pow-
ered off (see notes below).
33
11.
12V OUT A/ B
Note:
y
To use this feature, you must turn on the Screen Trigger function on the OSD.
y
Screen controllers are supplied and supported by screen manufacturers.
y
Do not use this jack for anything other than intended use.
HDP2300 Users Manual
– 6 –
ITEM LABEL DESCRIPTION SEE PAGE:
12.
VGA/ SCART/ YPbPr
Connects the RGB cable from a computer and
components
13.
S-VIDEO Connects the S-Video cable from a video device
12
14.
AC IN Connects the power cable
13
15.
Power switch Turns on/off the projector
15
16.
38
17.
Kensington Lock
Secures to permanent object with a Kensi
ngton® Lock
system
38
HDP2300 Users Manual
Security chain lock Helps protect the HDP2300 from unauthorized use
Bottom view
ITEM LABEL DESCRIPTION SEE PAGE:
171.
Tilt adjustor Rotate adjuster lever to adjust angle position.
2.
Ceiling support holes Contact your dealer for information on mounting the projector on a ceiling
Note:
When installing, ensure that you use only UL Listed ceiling mounts.
For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw
depth of 6 mm (0.23 inch).
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount
load capacity must exceed the weight of the installed equipment, and as an additional precaution
be capable of withstanding three times the weight of the equipment (not less than 5.15 kg) over a
period of 60 seconds.
7
HDP2300 Users Manual
Remote Control Functions
Important:
1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluo-
rescent lights can disrupt remote control operation.
2. Be sure nothing obstructs the path between the remote control and the projector. If the path be-
tween the remote control and the projector is obstructed, you can bounce the signal off certain
reflective surfaces such as projector screens.
3. The buttons and keys on the projector have the same functions as the corresponding buttons on
the remote control. This user’s manual describes the functions based on the remote control.
– 8 –
HDP2300 Users Manual
9
ITEM LABEL DESCRIPTION SEE PAGE:
1.
Power OFF Turns the projector off
13
2.
HDMI 2 Displays the HDMI 2 source selection
3.
S-VIDEO Displays the S-VIDEO source selection
4.
VIDEO Displays the VIDEO source selection
5.
Up cursor /
Keystone+
Navigates and changes settings in the OSD
Quick Menu – For Keystone
6.
ENTER Enters and confirms settings in the OSD
7.
Right cursor
8.
Down cursor
Navigates and changes settings in the OSD
21
9.
ASPECT RATIO Displays the ASPECT RATIO selections
10.
SOURCE Detects the input device
11.
STATUS
Opens the OSD Status menu
(the menu onl
y opens when an input device is detected)
21
12.
BRIGHT Displays the brightness setting bar
13.
SHARP Displays the sharpness setting bar
14.
COLOR Displays the color setting bar
15.
TINT Displays the tint setting bar
16.
BLANK Makes the screen blank
17.
FREEZE Freezes/unfreezes the on-screen picture
18.
AUTO Auto adjustment for frequency, phase, and position
19.
LIGHT
Turns on or off the remote control backlight for about 10 seconds. Pressing any
other key whi
le the backlight is on keeps the backlight on for a further 10 sec-
onds.
20.
VOL -
21.
VOL +
21
22.
MUTE Mutes the built-in speaker
23.
CONTRAST Displays the contrast settings bar
24.
PICTURE MODE Changes the Display Mode setting
25.
MENU/ EXIT Opens and exits the OSD
26.
Left cursor Navigates and changes settings in the OSD
21
27.
COMP Displays the Component source selection
28.
PC Displays the PC source selection
29.
HDMI 1 Displays the HDMI 1 source selection
30.
Power ON Turns the projector on
13
31.
IR transmitter Transmits signals to projector
HDP2300 Users Manual
Adjusts volume (HDP2300 without Audio Function)
– 10 –
Remote Control Operating Range
The remote control uses infrared transmission to control the projector. It is not necessary to point the
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or
the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and
15 degrees above or below the projector level. If the projector does not respond to the remote control,
move a little closer.
Projector and Remote Control Buttons
The projector can be operated using the remote control or the buttons on the top of the projector. All
operations can be carried out with the remote control; however, the buttons on the projector are lim-
ited in use.
HDP2300 Users Manual
S
ETUP AND
O
PERATION
Inserting the Remote Control Batteries
1.
Remove the battery compartment cover
by sliding the cover in the direction of
the arrow.
2.
Insert the battery with the positive side
facing up.
3.
Replace the cover.
Caution:
1. Only use AA batteries (Alkaline batteries are recommended).
2. Dispose of used batteries according to local ordinance regulations.
3. Remove the batteries when not using the projector for prolonged periods.
11
Connecting Input Devices
A PC or notebook computer and video devices can be connected to the projector at the same time. Video
devices include DVD, VCD, and VHS players, as well as movie camcorders and digital still cameras.
Check the user manual of the connecting device to confirm it has the appropriate output connector.
ITEM LABEL DESCRIPTION
VIDEO Connect the composite cable from a video device
YPbPr Connect a component video enabled device
HDMI 1/ 2/ 3 Connect the HDMI cable from a HDMI device
USB Connect the USB cable from a computer
RS-232C Connect RS-232 serial port cable for remote control
When connected to the screen through a commercially available cable, the
screen deploys automatically on start up of the projector. The screen retracts
when the projector is powered off.
12V OUT A/ B
VGA/ SCART/ YPbPr Connects the RGB cable from a computer and components
S-VIDEO Connect the S-VIDEO cable from a video device
Warning:
As a safety precaution, disconnect all power to the projector and connecting devices before making
connections.
– 12 –
HDP2300 Users Manual
Installing or Removing the Optional Lens
Caution:
y
Do not shake or place excessive pressure on the projector or the lens components as the projec-
tor and lens components contain precision parts.
y
Before removing or installing the lens, be sure to turn off the projector, wait until the cooling fans
stop, and turn off the main power switch.
y
Do not touch the lens surface when removing or installing the lens.
y
Keep fingerprints, dust or oil off the lens surface.
y
Do not scratch the lens surface.
y
Work on a level surface with a soft cloth under it to avoid scratching.
y
If you remove and store the lens, attach the lens cap to the projector to keep off dust and dirt.
Removing the Existing Lens From the Projector
1.
Pull and release the top cover to open as
shown.
2.
Push the LENSE RELEASE button to
the unlock position.
3.
Grasp the lens.
4.
Rotate the lens counterclockwise.
The existing lens will be disengaged.
5.
Pull out the existing lens slowly.
13
HDP2300 Users Manual
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57

Knoll HDP2300 User manual

Category
Projectors
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI