NavLinkz VL2-TOM Installation guide

NavLinkz
Brand
NavLinkz
Model
VL2-TOM
Category
Motorcycle Accessories
Type
Installation guide

NavLinkz VL2-TOM is an interface for connecting aftermarket reversing cameras and video sources to Renault vehicles with original TomTom navigation systems. It allows for the integration of up to two video sources, such as a reversing camera and a DVD player, into the factory-fitted navigation system. The interface seamlessly switches between the original navigation display and the video input when the vehicle is put into reverse or when a video source is selected.

NavLinkz VL2-TOM is an interface for connecting aftermarket reversing cameras and video sources to Renault vehicles with original TomTom navigation systems. It allows for the integration of up to two video sources, such as a reversing camera and a DVD player, into the factory-fitted navigation system. The interface seamlessly switches between the original navigation display and the video input when the vehicle is put into reverse or when a video source is selected.

Multi Media InterfaceMulti Media Interface
RENAULT TOMTOMRENAULT TOMTOM
Micro
Controller
Micro
Controller
AdjustAdjust Audio 1Audio 1 Audio 2Audio 2 Audio Audio
Video
Converter
Video
Converter
PowerPowerRGB inputRGB input Video 2Video 2
AdjustAdjust TOMTOMTOMTOM
CameraCameraVideo 1Video 1
Audio 1+2 in / outAudio 1+2 in / out
Monitor DATAMonitor DATALVDSLVDS
CtrlCtrl
345811 91012
24 23 21 20 19 18 17 16 15 14 1322
1
VIDEO 1
VIDEO 2
MANUAL
INFOMAP
BACK
MENUDEST
REPEAT LIGHT
HOME SET
2D/3D ROUTE
AUDIO 1
AUDIO 2
1. IDRV Swich
2. SPEED
3. LIGHT
4. REVERSE
5. ACC OUT
6. AIR CON
7. BATT
8. GND
OUT
1. BATT
2. GND
3. CAN-
4. CAN+
REVERSE
AUX
MONITOR CONNECTOR
AUDIO OUTPUT
CENTER
CONTROL
TOMTOM
MONITOR
RGB inputRGB input Video 1Video 1 PowerPowerVideo 2Video 2 CameraCameraSettingsSettings
VIDEO 1
VIDEO 2
SwitchSwitch
1 2
4
5 6
7 8
T9
2
2
3
4
1
5
2
2
2
2
1
1
2
1
4
3
3
1
See the next page for additional pictures
TOMTOM navigationboard 2011
TOMTOM navigationboard 2010
2
1
1
2
13 14
9
11 12
10
2
1
1
2
2
2
1
3
4
3 & 4 1 & 2
T9
Use two fingers to lock the flat cable connector like you see below! Don’t lock it in the middle
12 1
24 13
3457811 691012
24 23 21 20 19 18 17 16 15 14 1322
12V
GND
(7) Ground (BROWN)
Backside of the 24 Pins connector seen from behind the monitor
12345678
DIP ON
(6) 12V +30 (RED)
12
(2) CAN - (GREY)
(1) CAN + (BLUE)
YELLOW
RED
BLACK
GREEN
WHITE
12V BATT
12V ACC
GROUND
12V REVERSE
INTERFACE TRIGGER (5~12V PULSE)
1
2
3
4
5
6
7
8
RGB
VIDEO 1
VIDEO 2
X
CAMERA
X
X
X
UP (OFF)
ONLY WHEN VIDEO 1 WILL BE USED
ONLY WHEN ALSO VIDEO 2 WILL BE USED
X
ONLY WHEN THE REVERSE CAMERA WILL BE USED
X
X
X
VIDEO 1 VIDEO 2 CAMERA
CAN BUS
~~ ~~
CAN+
CAN-
1. IDRV Swich
2. SPEED
3. LIGHT
4. REVERSE
5. ACC OUT
6. AIR CON
7. BATT
8. GND
OUT
1. BATT
2. GND
3. CAN-
4. CAN+
POWER SUPPLY
Add an additional cable without cutting the original cable
Position 7
Position 6
Position 2
Postion 1
Ground
12V BATT
CAN low
CAN high
Add the BROWN ground cable from the CAN box
Add the RED 12V BATT cable from the CAN box
Add the GREY CAN- cable from the CAN box
Add the BLUE CAN+ cable from the CAN box
Position 7
BLUE
ORANGE
BLACK
12V TRIGGER (ONLY when CAN box doesn’t create a reverse signal)
12V Camera power
Camera GROUND
See the additional explanation about the camera connection of the wires on the last page!
The monitor is not showing the original image
Make sure the flat cables have the colored marks
at the right position! (See picture)
The switchboard is running one by one when the
interface is not connected or active.
Interfacebox
Switchboard
The monitor is not showing external images
Make sure the long flat cable with the blue marks
is connected like the pictures.
The blue marks should be located on the top side.
No camera image check:
Dip switch 5 ON (down)
No video image check:
Dip switch 2 ON (video 1)
Dip switch 3 ON (video 2)
12345678
DIP ON
1. IDRV Swich
2. SPEED
3. LIGHT
4. REVERSE
5. ACC OUT
6. AIR CON
7. BATT
8. GND
OUT
BLUE
ORANGE
BLACK
12V TRIGGER (ONLY when CAN box doesn’t create a reverse signal)
12V Camera power
Camera GROUND
To Camera input (interface box)
®
Camera TOMTOM5 sec
The image is becoming black for 5 seconds after
switching out of the reverse.
The camera should be powered by the orange
wire in case the CAN box is switching the interface
box.
The camera should be powered by ACC in case the
CAN box is not switching the interface box
Carvision measured the CAN bus signals from most Renault models available in the market. In case the CAN box is not recognizing the revesere signal, you
should connect the camera like the bottom drawing! (OPTION 2)
OPTION 1: Connect the camera like this
OPTION 2: ONLY connect the camera like below when the CAN box is not controlling the interface box!
The camera is powered by reverse signal wire!!!
TROUBLE SHOOTING
1. IDRV Swich
2. SPEED
3. LIGHT
4. REVERSE
5. ACC OUT
6. AIR CON
7. BATT
8. GND
OUT
BLUE
ORANGE
BLACK
12V TRIGGER (ONLY when CAN box doesn’t create a reverse signal)
12V Camera power
Camera GROUND
To Camera input (interface box)
Reverse light signal
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

NavLinkz VL2-TOM Installation guide

NavLinkz
Brand
NavLinkz
Model
VL2-TOM
Category
Motorcycle Accessories
Type
Installation guide

NavLinkz VL2-TOM is an interface for connecting aftermarket reversing cameras and video sources to Renault vehicles with original TomTom navigation systems. It allows for the integration of up to two video sources, such as a reversing camera and a DVD player, into the factory-fitted navigation system. The interface seamlessly switches between the original navigation display and the video input when the vehicle is put into reverse or when a video source is selected.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents