Supermicro X5DP8-G2 User manual

®

SUPER X5DP8-G2

SUPER X5DPE-G2

SUPER X5DPR-8G2+

SUPER X5DPR-iG2+

SUPER X5DPi-G2

USER’S MANUAL

Revision 1.1c

SUPER

The information in this User’s Manual has been carefully reviewed and is believed to be

accurate. The vendor assumes no responsibility for any inaccuracies that may be

contained in this document, makes no commitment to update or to keep current the

information in this manual, or to notify any person or organization of the updates.

Please Note: For the most up-to-date version of this manual, please

see our web site at www.supermicro.com.

SUPERMICRO COMPUTER reserves the right to make changes to the product described in

this manual at any time and without notice. This product, including software, if any, and

documentation may not, in whole or in part, be copied, photocopied, reproduced, translated

or reduced to any medium or machine without prior written consent.

IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT,

SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR

INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, THE VENDOR SHALL NOT HAVE

LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE

PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,

INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of

Santa Clara County in the State of California, USA. The State of California, County of

Santa Clara shall be the exclusive venue for the resolution of any such disputes.

Supermicro's total liability for all claims will not exceed the price paid for the hardware

product.

Unless you request and receive written permission from SUPER MICRO COMPUTER, you

may not copy any part of this document.

Information in this document is subject to change without notice. Other products and

companies referred to herein are trademarks or registered trademarks of their respective

companies or mark holders.

Printed in the United States of America

iii

Preface

About This Manual

This manual is written for system integrators, PC technicians and

knowledgeable PC users. It provides information for the installation and use

of the SUPER X5DP8-G2/X5DPE-G2/X5DPR-8G2+/X5DPR-iG2+/X5DPi-G2

mainboard. The SUPER X5DP8-G2/X5DPE-G2/X5DPR-8G2+/X5DPR-iG2+/

X5DPi-G2 supports single or dual Intel

®

603/604-pin Xeon

TM

processors at

up to 3.20 GHz at a 533/400 MHz front side bus. Please refer to the support

section of our web site (http://www.supermicro.com/TechSupport.htm) for a com-

plete listing of supported processors. This product is intended to be profession-

ally installed.

Manual Organization

Chapter 1 begins with a checklist of what should be included in your mainboard

box, describes the features, specifications and performance of the motherboard

and provides detailed information about the chipset.

Chapter 2 begins with instructions on handling static-sensitive devices. Read

this chapter when you want to install the processor and DIMM memory modules

and when mounting the mainboard in the chassis. Also refer to this chapter to

connect the floppy and hard disk drives, SCSI drives, the IDE interfaces, the

parallel and serial ports, the keyboard and mouse, the power supply and various

control panel buttons and indicators.

If you encounter any problems, see Chapter 3, which describes troubleshooting

procedures for the video, the memory and the setup configuration stored in

CMOS. For quick reference, a general FAQ [Frequently Asked Questions] sec-

tion is provided. Instructions are also included for contacting technical support.

In addition, you can visit our web site (at www.supermicro.com/techsupport.htm)

for more detailed information.

Chapter 4 includes an introduction to BIOS and provides detailed information on

running the CMOS Setup utility.

Appendix A gives information on BIOS POST messages.

Appendix B provides BIOS POST codes.

iv

Preface

About This Manual ...................................................................................................... iii

Manual Organization ................................................................................................... iii

Chapter 1: Introduction

1-1 Overview......................................................................................................... 1-1

Checklist .................................................................................................... 1-1

Contacting Supermicro............................................................................ 1-2

Super X5DP8-G2 Image .......................................................................... 1-4

Super X5DPR-8G2+ Image ..................................................................... 1-5

Super X5DP8-G2 Layout ........................................................................ 1-6

Super X5DP8-G2/DPE-G2/DPi-G2 Quick Reference ........................... 1-7

Super X5DPR-8G2+ Layout.................................................................... 1-8

Super X5DPR-8G2+/DPR-iG2+ Quick Reference ................................ 1-9

Motherboard Features ........................................................................... 1-10

Intel E7501 Chipset: System Block Diagram...................................... 1-12

1-2 Chipset Overview......................................................................................... 1-13

1-3 Special Features........................................................................................... 1-13

ATI Graphics Controller ........................................................................ 1-13

Recovery from AC Power Loss ......................................................... 1-13

1-4 PC Health Monitoring.................................................................................... 1-14

1-5 ACPI Features ............................................................................................... 1-15

1-6 Power Supply ............................................................................................... 1-17

1-7 Super I/O.........................................................................................................1-17

Chapter 2: Installation

2-1 Static-Sensitive Devices ............................................................................... 2-1

Precautions............................................................................................... 2-1

Unpacking.................................................................................................. 2-1

2-2 PGA Processor and Heatsink Installation .................................................. 2-2

2-3 Installing DIMMs............................................................................................... 2-5

2-4 I/O Ports/Control Panel Connectors............................................................. 2-6

2-5 Connecting Cables .......................................................................................... 2-8

ATX Power Connection .......................................................................... 2-8

PWR_SEC Connection ............................................................................. 2-8

Power LED................................................................................................. 2-8

NMI Button .................................................................................................. 2-8

HDD LED .................................................................................................... 2-9

Table of Contents

SUPER X5DP8-G2/DPE-G2/DPR-8G2+/DPR-iG2+/DPi-G2 User's Manual

Table of Contents

v

NIC2 LED ................................................................................................... 2-9

NIC1 LED ................................................................................................... 2-9

Overheat LED ........................................................................................... 2-9

Power Fail Button ..................................................................................... 2-9

Reset Button........................................................................................... 2-10

Power Button ......................................................................................... 2-10

Chassis Intrusion ................................................................................... 2-10

Universal Serial Bus (USB0/1) ............................................................ 2-10

Extra Universal Serial Bus Headers (USB2/3) ................................. 2-11

Serial Ports ............................................................................................. 2-11

GLAN1/2 (Ethernet Ports) ..................................................................... 2-11

Fan Headers........................................................................................... 2-12

Power LED/Speaker/NMI Header (JD1).............................................. 2-12

Third Power Supply Fail Header .......................................................... 2-12

ATX PS/2 Keyboard and Mouse Ports................................................ 2-13

Wake-On-LAN ......................................................................................... 2-13

Wake-On-Ring ......................................................................................... 2-13

Keylock ..................................................................................................... 2-13

2-6 Jumper Settings ............................................................................................ 2-14

Explanation of Jumpers ........................................................................ 2-14

CMOS Clear............................................................................................. 2-14

GLAN Enable/Disable............................................................................. 2-15

VGA Enable/Disable ............................................................................... 2-15

Front Side Bus Speed ........................................................................... 2-15

SCSI Enable/Disable................................................................................ 2-15

SCSI Termination Enable/Disable.......................................................... 2-16

Thermal Fan Enable/Disable.................................................................. 2-16

Watch Dog Enable/Disable ....................................................................2-16

2-7 Onboard Indicators ...................................................................................... 2-17

LAN1/LAN2 LEDs.................................................................................... 2-17

2-8 Parallel Port, Floppy/Hard Disk Drive and SCSI Connections............... 2-18

Parallel Port Connector ......................................................................... 2-18

Floppy Connector................................................................................... 2-19

IDE Connectors ...................................................................................... 2-19

Ultra320/160 SCSI Connectors............................................................. 2-20

2-9 Installing Software Drivers......................................................................... 2-21

vi

Chapter 3: Troubleshooting

3-1 Troubleshooting Procedures ........................................................................ 3-1

Before Power On .................................................................................... 3-1

No Power .................................................................................................. 3-1

No Video ................................................................................................... 3-1

Memory Errors.......................................................................................... 3-2

Losing the System’s Setup Configuration ........................................... 3-2

3-2 Technical Support Procedures .................................................................... 3-2

3-3 Frequently Asked Questions........................................................................ 3-3

3-4 Returning Merchandise for Service............................................................ 3-5

Chapter 4: BIOS

4-1 Introduction....................................................................................................... 4-1

4-2 Running Setup.................................................................................................. 4-2

4-3 Main Setup........................................................................................................ 4-2

4-4 Advanced Setup.............................................................................................. 4-6

4-5 Security Setup ............................................................................................... 4-15

4-6 Power Setup .................................................................................................. 4-17

4-7 Boot Setup...................................................................................................... 4-19

4-8 PIR Setup ........................................................................................................ 4-20

4-9 Exit ................................................................................................................... 4-22

Appendices:

Appendix A: BIOS POST Messages ..................................................................... A-1

Appendix B: BIOS POST Codes .............................................................................B-1

SUPER X5DP8-G2/DPE-G2/DPR-8G2+/DPR-iG2+/DPi-G2 User's Manual

Chapter 1: Introduction

1-1

Introduction

Chapter 1

Introduction

1-1 Overview

Checklist

Congratulations on purchasing your computer motherboard from an ac-

knowledged leader in the industry. Supermicro boards are designed with

the utmost attention to detail to provide you with the highest standards in

quality and performance.

Please check that the following items have been included with your mother-

board. If anything listed here is damaged or missing, contact your retailer.

One (1) Supermicro Mainboard

One (1) ribbon cable for IDE devices

One (1) floppy ribbon cable

One (1) serial port cable

One (1) USB cable

One (1) I/O backpanel shield (X5DP8-G2, X5DPE-G2, X5DPi-G2 only)

One (1) Supermicro CD or diskettes containing drivers and utilities

One (1) User's/BIOS Manual

Two (2) Pentium 4 Xeon active heatsinks (FAN-042-CF) and two (2)

heatsink retention clips (SKT-095-604*, X5DP8-G2, X5DPE-G2,

X5DPi-G2 only) *for 604-pin processors only.

SCSI Accessories (not included with the X5DPE-G2/DPR-iG2+/DPi-G2)

One (1) 68-pin LVD Ultra320/160 SCSI cable

One (1) set of SCSI driver diskettes

One (1) SCSI manual

1-2

Introduction

SUPER X5DP8-G2/DPE-G2/DPR-8G2+/DPR-iG2+/DPi-G2 User's Manual

Contacting Supermicro

Headquarters

Address: SuperMicro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: +1 (408) 503-8000

Fax: +1 (408) 503-8008

Email: [email protected] (General Information)

[email protected] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: SuperMicro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: +31 (0) 73-6400390

Fax: +31 (0) 73-6416525

Email: [email protected] (General Information)

[email protected] (Technical Support)

[email protected] (Customer Support)

Asia-Pacific

Address: SuperMicro, Taiwan

D5, 4F, No. 16 Chien-Ba Road

Chung-Ho 235, Taipei Hsien, Taiwan, R.O.C.

Tel: +886-(2) 8226-3990

Fax: +886-(2) 8226-3991

Web Site: www.supermicro.com.tw

Technical Support:

Email: su[email protected]

Tel: 886-2-8228-1366, ext.132 or 139

Chapter 1: Introduction

1-3

Introduction

Notes

1-4

Introduction

SUPER X5DP8-G2/DPE-G2/DPR-8G2+/DPR-iG2+/DPi-G2 User's Manual

Figure 1-1. SUPER X5DP8-G2 Image

Notes:

The X5DPE-G2 has the same basic layout as the X5DP8-G2 but with no SCSI.

The X5DPi-G2 has the same basic layout as the X5DP8-G2 but with no SCSI and a single SXB slot.

See the motherboard features section in this chapter for details on the specifications of each.

Chapter 1: Introduction

1-5

Introduction

Figure 1-2. SUPER X5DPR-8G2+ Image

Notes:

The X5DPR-iG2+ has the same layout as the X5DPR-8G2+ but with no SCSI.

See the motherboard features section in this chapter for details on the specifications of each.

1-6

Introduction

SUPER X5DP8-G2/DPE-G2/DPR-8G2+/DPR-iG2+/DPi-G2 User's Manual

Figure 1-3. SUPER X5DP8-G2 Layout*

(not drawn to scale)

DIMM #4B

DIMM #4A

DIMM #3B

DIMM #3A

DIMM #2B

DIMM #2A

DIMM #1B

DIMM #1A

BANK 4

BANK 3

BANK 2

BANK 1

ATX PWR CONN

JF2

JP36

J15

Parallel Port

VGA

COM1

CPU 2

USB 0/1

Keyboard

Mouse

J9

CPU 1

GLAN1

GLAN2

Rage

XL

Overheat Fan

Chassis Fan4

Chassis Fan3

JP9

USB 4

Chassis Fan2

CPU2 Fan

JL1

JP7

IDE #2

IDE #1

FLOPPY

Ultra III LVD SCSI CH A

Chassis Fan1

SMB

BIOS

Battery

P64H2

MCH

AIC-7902

ICH3

IPMI

USB 2

USB 3

Speaker

133 MHz PCI-X #6

133 MHz PCI-X #5

100 MHz PCI-X #4

66 MHz PCI-X #3

66 MHz PCI-X #2

66 MHz PCI-X #1

WOLJBT1 JWOR

Ultra SCSI CH B

COM2

JA1

JA4

JP4

JOH1

JD4

J7

SUPER X5DP8-G2

®

CPU1 Fan

JP39

JP23/Bus 2B

JP21/Bus 2B

JP19/Bus 2A

JP17/Bus 1B

JP18/Bus 1A

JP20/Bus 2B

J38

JP35

JPA2

JD1

PWR LED/SPKR/NMI

JPA1

J27

*Notes:

The IPMI socket is an optional feature.

Jumpers not noted are for test purposes only.

The X5DPE-G2 has the same basic layout as the X5DP8-G2 but with no SCSI.

The X5DPi-G2 has the same basic layout as the X5DP8-G2 but with no SCSI and a single SXB slot.

JP8

JP40

JP37

JP22

Chapter 1: Introduction

1-7

Introduction

X5DP8-G2/DPE-G2/DPi-G2 Quick Reference

Jumper Description Default Setting

JBT1 CMOS Clear See Jumper Section

JD1 Speaker Enable (Pins 6-7) Closed (Enabled)

JPA1/JPA2 SCSI CH A/B Termination Open (Enabled)

JD4 GLAN Enable/Disable Pins 1-2 (Enabled)

JP4 VGA Enable/Disable Pins 1-2 (Enabled)

JP9 Power Fail Alarm En/Disable Open (Disabled)

JP22 SCSI Enable/Disable Pins 1-2 (Enabled)

JP37 Watch Dog Enable/Disable Open (Disabled)

JP38 Thermal Fan Enable/Disable Open (BIOS Control)

JP39 Front Side Bus Speed Pins 1-2 (Auto)

Connector Description

ATX PWR CONN Primary ATX Power Connector

DIMM#1A-DIMM#4B Memory (RAM) Slots

COM1/COM2 COM1/COM2 Serial Port Connector

CPU/CHS/OH FAN CPU/Chassis/Overheat Fan Headers

GLAN1/2 Gigabit Ethernet Ports

IDE#1/IDE#2 IDE #1/#2 Hard Disk Drive Connectors

J7 Parallel (Printer) Port

J9 PS/2 Keyboard/Mouse Ports

J13/J14 USB2/3 Headers

J15 Secondary ATX Power Connector

JA1 Ultra160 LVD SCSI CH A Connector

JA4 Ultra160 LVD SCSI CH B Connector

JD1 PWR LED/Speaker/NMI/WD Header

JF2 Front Control Panel Connector

JL1 Chassis Intrusion Header

JOH1 Overheat LED

JP7 Floppy Disk Drive Connector

JP8 Third Power Supply Fail Header

JP35 Keylock Switch Connector

JP36 Alarm Reset Switch

JWOR Wake-on-Ring Header

SCSI LED SCSI Active LED Header

Speaker Onboard Speaker Header

USB0/1, 2/3, 4 Universal Serial Bus Ports, Headers

VGA VGA Display (Monitor) Port

WOL Wake-on-LAN Header

1-8

Introduction

SUPER X5DP8-G2/DPE-G2/DPR-8G2+/DPR-iG2+/DPi-G2 User's Manual

Figure 1-4. SUPER X5DPR-8G2+ Layout*

(not drawn to scale)

ATX POWER

CPU1

CPU2

J15

DIMM #3A

JP8

JF2

CPU1 Chassis FAN

DIMM #3B

DIMM #2B

DIMM #2A

BANK 3

BANK 2

Mouse

J28

Keyboard

J29

USB0/1

COM1

GLAN2

VGA

GLAN1

MCH

Rage XL

ICH3

Ultra III LVD/SE ChB

AIC-7902

CHS

FAN3

P64H2

BATTERY

COM2

BIOS

Speaker

Zero Channel RAID Socket

IPMI

IDE #1

IDE #2

FLOPPY

SMB

Ultra III LVD/SE ChA

WOL

JP22

FPUSB0,1/SLP/JBT1/WD/IR/CIR/USB2/PWRLED/Speaker/JL1

JD4

JPA1

JPA2

PCIX #1

SXB

PCIX #2

JP4

JP7

JA1

JA2

CPU2 Chassis FAN

SUPER X5DPR-8G2+

®

OHLED

JD1

WOR

JP35

*Notes:

The IPMI socket is an optional feature.

Jumpers not noted are for test purposes only.

The X5DPR-iG2 has the same layout as the X5DPR-8G2+ but with no SCSI.

DIMM #1B

DIMM #1A

BANK 1

JP36

JP9

JP38

Chapter 1: Introduction

1-9

Introduction

X5DPR-8G2+/X5DPR-iG2+ Quick Reference

Jumper Description Default Setting

JBT1 CMOS Clear See Jumper Section

JD1 Speaker Enable (Pins 6-7) Closed (Enabled)

JPA1/JPA2 SCSI Channel A/B Termination Open (Terminated)

JD4 GLAN Enable/Disable Pins 1-2 (Enabled)

JP4 VGA Enable/Disable Pins 1-2 (Enabled)

JP9 Power Fail Alarm En/Disable Open (Disabled)

JP22 SCSI Enable/Disable Pins 1-2 (Enabled)

JP37/JD1 Watchdog Enable/Disable Open (Disabled)

JP38 Front Side Bus Speed Pins 1-2 (Auto)

Connector Description

ATX POWER Primary ATX Power Connector

COM1/COM2 COM1/COM2 Serial Port Connector

CPU1/CPU2 CPU 1 and CPU2 Sockets

CPU CHS FAN CPU 1 & 2 Chassis Fan Headers

DIMM#1A-DIMM#3B Memory (RAM) Slots

GLAN1/2 Ethernet Ports

IDE#1/IDE#2 IDE #1/#2 Hard Disk Drive Connectors

JA1 LVD SCSI CH A Connector

JA2 LVD SCSI CH B Connector

JD1 JBT1/WD/IR/CIR/USB2/PWRLED/SPKR

JF2 Front Control Panel Connector

JP7 Floppy Disk Drive Connector

JP8 Third Power Supply Fail Header

JP35 Keylock Header

JP36 Alarm Reset Switch

J15 Secondary ATX Power Connector

J28 Keyboard Port

J29 Mouse Port

OHLED Overheat LED Header

USB0/1 Universal Serial Bus Ports

VGA VGA Display (Monitor) Port

WOL Wake-on-LAN Header

WOR Wake-on-Ring Header

1-10

Introduction

SUPER X5DP8-G2/DPE-G2/DPR-8G2+/DPR-iG2+/DPi-G2 User's Manual

Motherboard Features

CPU

• Single or dual Intel

®

604 and 603-pin Xeon

TM

processors of up to 3.20 GHz

at a 533/400 MHz front side (system) bus speed.

Note: Please refer to the support section of our web site for a complete listing of

supported processors (http://www.supermicro.com/TechSupport.htm).

Memory

• X5DP8-G2, X5DPE-G2, X5DPi-G2: Eight 184-pin DIMM sockets supporting

up to 16 GB of registered ECC DDR-266/200 SDRAM

• X5DPR-8G2+/X5DPR-iG2+: Six 184-pin DIMM sockets supporting up to

12 GB of registered ECC DDR-266/200 SDRAM

Note: Interleaved memory; requires memory modules to be installed in pairs. DDR-266 memory

must be used with 533 MHz FSB speed processors. See Section 2-3 for details.

Chipset

• Intel E7501 chipset

Expansion Slots

X5DP8-G2/DPE-G2 X5DPR-8G2+/DPR-iG2+/DPi-G2

• Two 64-bit, 133 MHz PCI-X • One 64-bit, 133 MHz PCI-X (SXB)

• One 64-bit, 100 MHz PCI-X • One slim 64-bit, 66 MHz PCI-X (not

• Three 64-bit, 66 MHz PCI-X included on X5DPi-G2)

• One SXB slot

BIOS

• 4 Mb Phoenix

®

Flash ROM

• APM 1.2, DMI 2.1, PCI 2.2, ACPI 1.0, Plug and Play (PnP), SMBIOS 2.3

PC Health Monitoring

• Onboard voltage monitors for CPU cores, chipset voltage, 3.3V, +5V,

+12V and 3.3V standby

• Fan status monitor with firmware/software on/off control

• CPU/chassis temperature monitors

• Environmental temperature monitor and control

• CPU fan auto-off in sleep mode

• CPU slow-down on temperature overheat

• CPU overheat LED header

• Power-up mode control for recovery from AC power loss

Chapter 1: Introduction

1-11

Introduction

• Auto-switching voltage regulator for CPU core

• System overheat LED and control

• Chassis intrusion detection

• System resource alert

ACPI Features (optional)

• Microsoft OnNow

• Slow blinking LED for suspend state indicator

• Main switch override mechanism

Onboard I/O

• AIC-7902 for dual channel Ultra320 SCSI (X5DP8-G2/DPR-8G2+)

• Integrated ATI Rage XL graphics controller

• Intel 82546EB dual port Gigabit LAN (Ethernet) controller

• 2 EIDE Ultra DMA/100 bus master interfaces

• 1 floppy port interface (up to 2.88 MB)

• 2 Fast UART 16550A compatible serial ports

• 1 EPP/ECP Parallel Port (X5DP8-G2/DPE-G2/DPi-G2/DP6)

• PS/2 mouse and PS/2 keyboard ports

• Up to 5 USB (Universal Serial Bus) ports

Other

• Internal/external modem ring-on

• Wake-on-LAN (WOL)

• Console redirection

• IPMI (optional)

CD/Diskette Utilities

• BIOS flash upgrade utility and device drivers

Dimensions

• X5DP8-G2/DPE-G2/DPi-G2: Ext. ATX: 12"x13.05" (304.8x331.5 mm)

• X5DPR-8G2+/DPR-iG2+: Extended ATX: 12"x13" (304.8x330.2 mm)

1-12

Introduction

SUPER X5DP8-G2/DPE-G2/DPR-8G2+/DPR-iG2+/DPi-G2 User's Manual

PCI-X Slot 6, SXB

MCH

533/400 MHz System Bus

266 MHz Memory Bus

ATA 100

Ports

P64H 2

P rocessor 1 Processor 0

2-C hannel DDR SDRAM

PCI-X Slot 5, G L A N 1 / 2

IC H 3-S

USB 1.1

Ports

SM Bus

Super IO

ATI G ra p h ics

P64H 2

PCI-X Slots 1-3

PCI-X Slot 4, S C S I

X5DP8-G2, X5DPE-G 2 and X5DPi-G 2

Figure 1-5. Intel E7501 Chipset:

System Block Diagram

Note: These are general block diagrams. Please see the previous Motherboard

Features pages for details on the features of each motherboard.

SCSI & Slim PCI Slot

MCH

533/400 MHz System Bus

266 MHz Memory Bus

ATA 100

Ports

P64H2

Processor 1 Processor 0

2-Channel DDR SDRAM

Dual GLAN & SXB

ICH3-S

USB 1.1

Ports

SMBus

Super IO

ATI

Graphics

SXB = Supermicro Extended

Bus PCI Slot

X5DPR-8G2+ and X5DPR-iG2+

Chapter 1: Introduction

1-13

Introduction

1-2 Chipset Overview

The Intel E7501 chipset is a high-performance chipset with a performance

and feature-set designed for mid-range, dual processor servers. The

E7501 chipset consists of four major components: the Memory Controller

Hub (MCH), the I/O Controller Hub 3 (ICH3), the PCI-X 64-bit Hub 2.0 (P64H2)

and the 82808AA Host Channel Adapter (VxB).

The MCH has four hub interfaces, one to communicate with the ICH3 and

three for high-speed I/O communications. The MCH employs a 144-bit wide

memory bus for a DDR-266 memory interface, which provides a total band-

width of 4.2 GB/s (3.2 GB/s for DDR-200). The ICH3 interface is a 266 MB/

sec point-to-point connection using an 8-bit wide, 66 MHz base clock at a

4x data transfer rate. The P64H2 interface is a 1 GB/s point-to-point con-

nection using a 16-bit wide, 66 MHz base clock at a 8x data transfer rate.

The ICH3 I/O Controller Hub provides various integrated functions, including

a two-channel UDMA100 bus master IDE controller, USB host controllers, a

System Management Bus controller and an AC'97 compliant interface.

Each of the P64H2 PCI-X Hubs (two on the X5DP8-G2, X5DPE-G2 and X5DPi-

G2 and one on the X5DPR-8G2+ and X5DPR-iG2+) provides a 16-bit con-

nection to the MCH for high-performance IO capability and two 64-bit PCI-X

interfaces.

1-3 Special Features

ATI Graphics Controller

The X5DP8-G2/X5DPE-G2/X5DPR-8G2+/X5DPR-iG2+/X5DPi-G2 has an inte-

grated ATI video controller based on the Rage XL graphics chip. The Rage

XL fully supports sideband addressing and AGP texturing. This onboard

graphics package can provide a bandwidth of up to 512 MB/sec over a 32-

bit graphics memory bus.

Recovery from AC Power Loss

BIOS provides a setting for you to determine how the system will respond

when AC power is lost and then restored to the system. You can choose

for the system to remain powered off (in which case you must hit the

power switch to turn it back on) or for it to automatically return to a power-

1-14

Introduction

SUPER X5DP8-G2/DPE-G2/DPR-8G2+/DPR-iG2+/DPi-G2 User's Manual

on state. See the Power Lost Control setting in the Advanced BIOS Setup

section (Peripheral Device Configuration) to change this setting. The de-

fault setting is Always On.

1-4 PC Health Monitoring

This section describes the PC health monitoring features of the SUPER

X5DP8-G2/X5DPE-G2/X5DPR-8G2+/X5DPR-iG2+/X5DPi-G2. All have an

onboard System Hardware Monitor chip that supports PC health monitoring.

Onboard Voltage Monitors for the CPU Cores, Chipset

Voltage, +3.3V, +5V, +12V and +3.3V Standby

An onboard voltage monitor will scan these voltages continuously. Once a

voltage becomes unstable, a warning is given or an error message is sent

to the screen. Users can adjust the voltage thresholds to define the

sensitivity of the voltage monitor.

Fan Status Monitor with Firmware/Software On/Off Control

The PC health monitor can check the RPM status of the cooling fans. The

onboard 3-pin CPU and chassis fans are controlled by the power manage-

ment functions. The thermal fan is controlled by the overheat detection

logic.

Environmental Temperature Control

The thermal control sensor monitors the CPU temperature in real time and

will turn on the thermal control fan whenever the CPU temperature exceeds

a user-defined threshold. The overheat circuitry runs independently from

the CPU. It can continue to monitor for overheat conditions even when the

CPU is in sleep mode. Once it detects that the CPU temperature is too high,

it will automatically turn on the thermal control fan to prevent any overheat

damage to the CPU. The onboard chassis thermal circuitry can monitor the

overall system temperature and alert users when the chassis temperature

is too high.

CPU Fan Auto-Off in Sleep Mode

The CPU fan activates when the power is turned on. It continues to operate

when the system enters Standby mode. When in sleep mode, the CPU will

not run at full power, thereby generating less heat.

Page is loading ...

Supermicro X5DP8-G2 User manual

Supermicro X5DP8-G2 User manual

Related papers

Other documents