Supermicro P8SGA-O User manual

®

P8SGA

USER’S MANUAL

Revision 1.0c

SUPER

The information in this User’s Manual has been carefully reviewed and is believed to be

accurate. The vendor assumes no responsibility for any inaccuracies that may be contained

in this document, makes no commitment to update or to keep current the information in this

manual, or to notify any person or organization of the updates.

Please Note: For the

most up-to-date version of this manual, please see our web site at

www.supermicro.com.

SUPERMICRO COMPUTER reserves the right to make changes to the product described in

this manual at any time and without notice. This product, including software, if any, and

documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or

reduced to any medium or machine without prior written consent.

IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT,

SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR

INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, THE VENDOR SHALL NOT HAVE

LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE

PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,

INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of

Santa Clara County in the State of California, USA. The State of California, County of Santa

Clara shall be the exclusive venue for the resolution of any such disputes. Supermicro's total

liability for all claims will not exceed the price paid for the hardware product.

Unless you request and receive written permission from SUPER MICRO COMPUTER, you

may not copy any part of this document.

Information in this document is subject to change without notice. Other products and

companies referred to herein are trademarks or registered trademarks of their respective

companies or mark holders.

Printed in the United States of America

Preface

About This Manual

This manual is written for system integrators, PC technicians and

knowledgeable PC users. It provides information for the installation and use

of the P8SGA motherboard. The P8SGA supports single Intel

Pentium

®

4 Processor (the Prescott Processor) in the 775-Land Grid Array

Package at a system bus speed of 800/533 MHz. The Pentium 4 Processor

in the 775-Land Grid Array Package is housed in a Flip-Chip Land Grid

Array (FC-LGA4) package that interfaces with the motherboard via an

LGA775 socket. The package consists of a processor core mounted on a

substrate land-carrier. An integrated heat spreader (IHS) is attached to the

package substrate and core and serves as the contacting surface for

processor component thermal solutions, such as a heatsink. Please refer

to the motherboard specifications pages on our web site (http://

www.supermicro.com/Product_page/product-m.htm) for updates on sup-

ported processors. This product is intended to be professionally installed.

Manual Organization

Chapter 1 includes a checklist of what should be included in your

mainboard box, describes the features, specifications and performance of

the P8SGA mainboard and provides detailed information about the chipset.

Chapter 2 begins with instructions on handling static-sensitive devices.

Read this chapter when installing the processor and DDR memory modules

and when mounting the mainboard in the chassis. Also refer to this chapter

to connect the floppy and hard disk drives, the IDE interfaces, the parallel

and serial ports, the mouse and keyboard and the twisted wires for the

power supply, the reset button, the keylock/power LED and the speaker.

If you encounter any problems, see Chapter 3, which describes trouble-

shooting procedures for the video, the memory and the setup configuration

stored in CMOS. For quick reference, a general FAQ (Frequently Asked

Questions) section is provided. Instructions are also included for contact-

ing technical support. In addition, you can visit our web site at

www.supermicro.com/techsupport.htm for more detailed information.

Chapter 4 includes an introduction to BIOS and provides detailed informa-

tion on running the CMOS Setup utility.

Appendix A provides BIOS POST Messages.

Appendix B lists BIOS POST Codes.

Preface

iii

P8SGAUser’s Manual

Table of Contents

Preface

About This Manual ...................................................................................................... iii

Manual Organization ................................................................................................... iii

Chapter 1: Introduction

1-1 Overview......................................................................................................... 1-1

Checklist .................................................................................................... 1-1

Contacting Supermicro............................................................................ 1-2

SUPER P8SGAImage ................................................................ 1-3

P8SGA Layout .......................................................................... 1-4

P8SGAQuick Reference ........................................................... 1-5

E7205 Chipset: System Block Diagram ................................................. 1-6

Motherboard Features ............................................................................ 1-7

1-2 Chipset Overview........................................................................................... 1-9

1-3 PC Health Monitoring.................................................................................... 1-10

1-4 Power Configuration Settings .................................................................... 1-11

1-5 Power Supply ............................................................................................... 1-12

1-6 Super I/O......................................................................................................... 1-13

Chapter 2: Installation

2-1 Static-Sensitive Devices ............................................................................... 2-1

2-2 Processor and Heatsink Installation............................................................ 2-2

2-3 Mounting the Motherboard in the Chassis ................................................. 2-5

2-4 Installing DDR Memory ................................................................................... 2-6

2-5 I/O Port/Front Control Panel Connector Locations.................................... 2-7

2-6 Connecting Cables ......................................................................................... 2-8

Power Supply Connectors ..................................................................... 2-8

IR Connector.............................................................................................. 2-8

PW_ON Connector ................................................................................... 2-9

Reset Connector ....................................................................................... 2-9

IDE/SATA LED ........................................................................................ 2-10

Power LED Connector ........................................................................... 2-10

Keylock Connector ................................................................................ 2-11

Speaker Connector................................................................................ 2-11

iv

v

Serial Ports ............................................................................................. 2-12

CD Header............................................................................................... 2-12

Fan Headers........................................................................................... 2-13

Chassis Intrusion ................................................................................... 2-13

ATX PS/2 Keyboard/Mouse Ports ....................................................... 2-14

Universal Serial Bus (USB).................................................................. 2-14

Wake-On-Ring ......................................................................................... 2-15

Wake-On-LAN ......................................................................................... 2-15

Ethernet Port............................................................................................ 2-15

VGA Connector....................................................................................... 2-16

SMB Header............................................................................................. 2-16

Overheat LED .......................................................................................... 2-17

AC'97 Output ...........................................................................................2-17

2-7 Jumper Settings............................................................................................ 2-18

Explanation of Jumpers ........................................................................ 2-18

CMOS Clear............................................................................................. 2-18

USB Wake-Up.......................................................................................... 2-19

Watch Dog Enable/Disable ....................................................................2-19

Keyboard Wake-Up................................................................................. 2-20

Gigabit LAN Enable................................................................................. 2-20

2-8 Parallel Port, Floppy/Hard Drive and Audio Connections ...................... 2-21

Parallel Port Connector ......................................................................... 2-21

Floppy Connector................................................................................... 2-22

IDE Connectors ...................................................................................... 2-22

2-9 Installing Software ....................................................................................... 2-23

SuperO Doctor III .................................................................................... 2-25

Chapter 3: Troubleshooting

3-1 Troubleshooting Procedures ........................................................................ 3-1

Before Power On .................................................................................... 3-1

No Power .................................................................................................. 3-1

No Video ................................................................................................... 3-1

Memory Errors.......................................................................................... 3-2

Losing the System’s Setup Configuration ........................................... 3-2

3-2 Technical Support Procedures .................................................................... 3-2

3-3 Frequently Asked Questions........................................................................ 3-3

3-4 Returning Merchandise for Service............................................................ 3-5

Table of Contents

P8SGA User’s Manual

Chapter 4: BIOS

4-1 Introduction....................................................................................................... 4-1

4-2 Running Setup.................................................................................................. 4-2

4-3 Main BIOS Setup.............................................................................................. 4-2

Main BIOS Setup Menu ........................................................................... 4-3

4-4 Advanced BIOS Setup.................................................................................... 4-5

4-4.1 Advanced BIOS Features............................................................ 4-5

4-4.2 Advanced Chipset Control........................................................... 4-7

4-4.3 I/O Device Configuration ............................................................ 4-10

4-4.4 PnP Configuration........................................................................ 4-12

4-4.5 Hardware Monitors ..................................................................... 4-14

4-4.6 Processor & Clock Options ....................................................... 4-15

4-5 Security........................................................................................................... 4-16

4-6 Boot ................................................................................................................. 4-17

4-7 Exit ................................................................................................................... 4-19

Appendices:

Appendix A: BIOS POST Messages ..................................................................... A-1

Appendix B: BIOS POST Codes .............................................................................B-1

vi

Chapter 1: Introduction

1-1

Chapter 1

Introduction

1-1 Overview

Checklist

Congratulations on purchasing your computer motherboard from an ac-

knowledged leader in the industry. Supermicro boards are designed with

the utmost attention to detail to provide you with the highest standards in

quality and performance.

Please check that the following items have all been included with your

motherboard. If anything listed here is damaged or missing, contact your

retailer.

All Included with Retail Box Only

One (1) Supermicro Mainboard

Two (2) SATA cables

One (1) COM port cable with bracket

One (1) IDE cable

One (1) floppy drive ribbon cable

One (1) I/O shield

One (1) Supermicro CD containing drivers and utilities

One (1) User's/BIOS Manual

1-2

P8SGA User’s Manual

Contacting Supermicro

Headquarters

Address: SuperMicro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: +1 (408) 503-8000

Fax: +1 (408) 503-8008

Email: [email protected] (General Information)

[email protected] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: SuperMicro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: +31 (0) 73-6400390

Fax: +31 (0) 73-6416525

Email: [email protected] (General Information)

[email protected] (Technical Support)

[email protected] (Customer Support)

Asia-Pacific

Address: SuperMicro, Taiwan

D5, 4F, No. 16 Chien-Ba Road

Chung-Ho 235, Taipei Hsien, Taiwan, R.O.C.

Tel: +886-(2) 8226-3990

Fax: +886-(2) 8226-3991

Web Site: www.supermicro.com.tw

Technical Support:

Email: su[email protected]

Tel: 886-2-8226-3990, ext.132 or 139

Chapter 1: Introduction

1-3

Figure 1-1. P8SGA Image

An Important Note to the User

• All images, layouts and contents included in this manual were based

upon PCB Revision 1.2, which was the latest revision available at the

time of publishing. The motherboard you've received may or may not

look exactly the same as the ones shown in this manual.

1-4

P8SGA User’s Manual

Figure 1-3. Motherboard Layout

(not drawn to scale)

x1 PCI-E#1

x1 PCI-E#2

S

UPER P8SGA

®

P4 CPU

LGA 775

JPWAKE

4-Pin 12V PWR

KB/MS

Parallel Port

COM1 Port

Video Port

USB

3/4/5/6

USB1/2

& LAN

JPUSB

Fan3

Clock

915G

Glantsdale

(North Bridge)

x16 PCI-E

PCI-3

PCI-2

PCI-1

LAN CTRL

JPL

GLAN Enable

CDin

Aux.

x1 PCI-E#3

AC97

COM2

FWH

J43

CL CMOS

JL1

WOR

SATA0

SATA1

SATA2

SATA3

FP CTRL

Fan2

JF1

JOH1

Buzzer

JP5

ID

E

24-Pin ATX PWR

Super IO

Fan1

Front USB7/8

WD Reset

Chs Intru.

ICH6

J34 SMB

DIMM#1A (Blue)

DIMM#2A (Black)

DIMM#1B (Blue)

DIMM#2B (Black)

Floppy

Audio

WOL

JBT1

OH

J3

J27

J40

(South Bridge)

J13

J45

J11

J44

JG1

J31

J28

J41

KB/MS Wake-Up

J30

Battery

JPUSB2

JPUSB3

Important Notes to the User

• All images, layouts and contents included in this manual were based

upon PCB Revision 1.2, which was the latest revision available at the

time of publishing. The motherboard you've received may or may not

look exactly the same as the ones shown in this manual.

• See Chapter 2 for detailed information on jumpers, I/O ports and JF1

front panel connections.

Chapter 1: Introduction

1-5

P8SGA Quick Reference

Jumpers Description Default Setting

JBT1 CMOS Clear See Section 2-7

JP5 Watch Dog Pins 1-2 (Enabled)

JPL Giga-bit LAN Enable Pins 1-2 (Enabled)

JPUSB USB 1/2 Wake Up Pins 2-3 (Disabled)

JPUSB2 USB 3/4/5/6 Wake Up Pins 2-3 (Disabled)

JPUSB3 USB 7/8 Wake Up Pins 2-3 (Disabled)

JPWAKE KB/Mouse Wake-Up Pins 1-2 (Enabled)

Connectors Description

ATX PWR(J40) ATX 24-Pin Power Connector

CPU PWR(J41) 12V 4-pin Power Connector(*required)

Audio Audio Port

AUX Auxiliary (Audio) Input Header

CD In Audio CD Input Header

Chassis Intrusion(JL1) Chassis Intrusion Header

COM1, COM2 COM Port/Serial Port 1 & Port 2 Connectors

DIMM#1A,#2A,#1B,#2B Memory (DIMM) slots (1 through 4)

Fans 1-3 Fan1: CPU Fan, Fan2/3: Chassis Fan Headers

Floppy Connector Floppy Disk Connector

FR Control Panel(JF1) Front Control Panel Header

(G-) LAN Port Ethernet RJ45 (Gigabit LAN) Connector

IDE (J27) IDE Connector

OH LED(JOH1) Overheat LED Header

Printer (J30) Parallel Printer Port

KB/Mouse (J28) PS/2 Keyboard/Mouse

SATA #0-3 4 SATA Headers

SMB (J34) System Management Bus Header

USB 1/2 (J11) (Back Panel) Universal Serial Ports 1-2

USB 3/4/5/6 (J44) (Back Panel) Universal Serial Ports 3-6

USB7/8 (J43) (Front Panel) USB ports 7/8

VGA (JG1) Video/Graphic Connector

WOR(JWOR1) Wake-On-Ring Header

1-6

P8SGA User’s Manual

Figure 1-3. 915G Grantsdale Chipset:

System Block Diagram

Note: This is a general block diagram and may not exactly

represent the features on your motherboard. See the follow-

ing pages for the actual specifications of each motherboard.

GRANTSDALE

SLOTS

LGA775_PROCESSOR

ICH-6

USB

PORT_0~7

FWH

LPC I/O

MS.

KB. FDD. SER.1

SER.2

PRN.

PRI_IDE

VRM 10.1

ADDR

CTRL CTRL

ADDR

DATADATA

UDMA/100

LPC

PCI_32_BUS

DDR_SDRAM

VRM V10.1

DMI

3_PCI_x32

DIMM_CHA

S-ATA/150

4 x SATA

CK410 CLK

1 PCIE_x16

GRAPHIC

MCH

DIMM_CHB

PORTS

PCIE_x16

INTEGRATED

GRAPHIC

Gb_LAN

SLOTS

3_PCIE_x1

PCIE_x1

W83627HF 5.1-CH

AUDIO

FSB: 800/533MHz

LPCUSB 2.0/1.1

AC97

Chapter 1: Introduction

1-7

Motherboard Features

CPU ! Latest CPU technology!

• Single Intel Pentium

®

4 Processor w/FSB 800 MHz or Celeron Proces-

sor w/FSB 533 MHz in the 775-Land Grid Array Package.

• Supports Intel Hyper-Threading Technology.

Memory ! Latest memory technology!

• Dual/Single Channel DDR up to 4 GB of non-ECC unbuffered, two-way

interleaved or non-interleaved DDR-400/333 SDRAM in 4 DIMMS Note:

See Section 2-4 for details.

Chipset ! Latest Intel chipset technology!

• Intel Glantsdale 915G

Expansion Slots

• One (1) PCI-Express x16 (intended for graphics)

• Three (3) PCI-Express x1

• Three (3) 32-bit PCI 33MHz (5V)

BIOS

• 4 Mb Firmware Hub AwardBIOS

®

Flash BIOS

• APM 1.2, DMI 2.3, PCI 2.2, ACPI 1.0, Plug and Play (PnP)

PC Health Monitoring

• Eight onboard voltage monitors for CPU core, +3.3V, +3.3V standby,

+5V, +1.5V, Vbat (battery voltage) and ±12V

• Fan status monitor with firmware/software 4 pin fan speed control

• SuperDoctor III, Watch Dog, NMI

• Environmental temperature monitoring via BIOS

• Power-up mode control for recovery from AC power loss

• System overheat LED and control

• System resource alert via Supero Doctor III

• Auto-switching voltage regulator for the CPU core

1-8

P8SGA User’s Manual

ACPI Features

• Microsoft OnNow

• Slow blinking LED for suspend state indicator

• BIOS support for USB keyboard

• Main switch override mechanism

• Internal/external modem ring-on

Onboard I/O

• 1 ATA/100 EIDE Channel s for a total of two IDE devices backward

compatible

• Built in ICH6 SATA Controller, 4 connectors for 4 devices

• 1 floppy port interface (up to 2.88 MB)

• 2 Fast UART 16550 compatible serial ports

• Intel 82541 Gigabit Ethernet Controller

• 1 EPP (Enhanced Parallel Port) and ECP (Extended Capabilities Port)

supported parallel port

• PS/2 mouse and PS/2 keyboard ports

• Up to 8 USB (Universal Serial Bus) 2.0 ports for a speed of up to

480Mbps ! Latest USB 2.0 technology!

• AC'97 audio high quality 6-channel sound

• Integrated (3rd generation) gfx core graphics on board

Other

• Wake-on-LAN

• Wake-on-Ring (WOR)

• Multiple CPU clock frequency ratio selections (set in BIOS)

• Suspend-to-RAM

• Onboard +5vsb warning LED ("LE1")

CD Utilities

• BIOS flash upgrade utility

• Drivers and software for Intel 915G chipset utilities

Dimensions

• ATX form factor, 12" x 9.5" (305 x 240 mm)

Chapter 1: Introduction

1-9

1-2 Chipset Overview

Intel’s Grantsdale (915G) chipset, is comprised of two primary components:

the Graphics Memory Controller Hub (GMCH) and the I/O Controller Hub

(ICH6). The Grantsdale (915G) provides the performance and feature-set

required for high-end single-processor desktop solutions.

Graphics Memory Controller Hub (GMCH)

The function of the GMCH is to manage the data flow between five inter-

faces: the CPU interface Front Side Bus (FSB), System Memory Interface

(DRAM controller), PCI Express Graphic Interface, I/OController and the Di-

rect Media Interface (DMI). The GMCH is optimized for the Prescott proces-

sors in an LGA775 Package. It supports one or two channels of unbuf-

fered, non-ECC DDR 400/333 SDRAM. It also supports the PCI-Express-

based external graphics solutions.

The ACPI component provides the data buffering and interface arbitration

required to ensure that system interfaces operate efficiently. The Direct

Media Interface (DMI) is a point-to-point interconnect between the

Grantsdale GMCH and the ICH6. Virtually all communication between the

GMCH and the ICH occurs over the Direct Media Interface. DMI supports

2GB/s (IGB/s each direction) of bandwidth, using a 100 MHz differential

clock.

Intel ICH6 System Features

The I/O Controller Hub provides the I/O subsystem with access to the rest

of the system. Functions and capabilities include:

*PCI Express Base Specification, Rev. 1.0a-compliant

*PCI 2.3

*ACPI Power Management Logic Support

*USB host interface

*Enhanced DMA Controller

*System Management Bus

*Low Pin Count (LPC) Interface

*Firmware Hub (FWH) Interface

Graphics Features/Display

The Grantsdale GMCH provides an integrated graphics accelerator deliver-

ing 3D, 2D and video capabilities. It also provides interfaces to a progres-

sive scan analog monitor and two DVO devices. It is compliant with DVI

specification and has a high-speed interface to a digital display.

1-10

P8SGA User’s Manual

1-3 PC Health Monitoring

This section describes the PC health monitoring features of the P8SGA.

The motherboard has an onboard System Hardware Monitor chip that sup-

ports PC health monitoring.

Eight Onboard Voltage Monitors for the CPU Core, Chipset

Voltage, +3.3V, +3.3V standby,

++

+5V, 1.5V, Vbat and

±±

±12V

The onboard voltage monitor will scan these voltages continuously. Once a

voltage becomes unstable, it will give a warning or send an error message

to the screen. Users can adjust the voltage thresholds to define the sensi-

tivity of the voltage monitor.

Fan Status Monitor with Firmware/Software

The PC health monitor can check the RPM status of the cooling fans via

Supero Doctor.

CPU Overheat LED and Control

This feature is available when the user enables the CPU overheat warning

function in the BIOS. This allows the user to define an overheat tempera-

ture. When this temperature reaches the threshold, the CPU thermal trip

feature will be activated and it will send a signal to the Speaker LED and, at

the same time, the CPU speed will be decreased.

Chapter 1: Introduction

1-11

1-4 Power Configuration Settings

This section describes features of your motherboard that deal with power

and power settings.

Microsoft OnNow

The OnNow design initiative is a comprehensive, system-wide approach to

system and device power control. OnNow is a term for a PC that is always

on but appears to be off and responds immediately to user or other re-

quests.

Slow Blinking LED for Suspend-State Indicator

When the CPU goes into a suspend state, the chassis power LED will start

blinking to indicate that the CPU is in suspend mode. When the user presses

any key, the CPU will wake-up and the LED will automatically stop blinking

and remain on.

BIOS Support for USB Keyboard

If the USB keyboard is the only keyboard in the system, it keyboard will

function like a normal keyboard during system boot-up.

Main Switch Override Mechanism

When an ATX power supply is used, the power button can function as a

system suspend button. When the user depresses the power button, the

system will enter a SoftOff state. The monitor will be suspended and the

hard drive will spin down. Depressing the power button again will cause

the whole system to wake-up. During the SoftOff state, the ATX power

supply provides power to keep the required circuitry in the system alive. In

case the system malfunctions and you want to turn off the power, just

depress and hold the power button for 4 seconds. The power will turn off

and no power will be provided to the motherboard.

Wake-On-Ring (WOR) Header

Wake-up events can be triggered by a device such as the external modem

ringing when the system is in the SoftOff state. Note that external modem

ring-on can only be used with an ATX 2.01 (or above) compliant power

supply.

1-12

P8SGA User’s Manual

1-5 Power Supply

As with all computer products, a stable power source is necessary for

proper and reliable operation. It is even more important for processors that

have high CPU clock rates of 1 GHz and faster.

The P8SGA accommodates 12V ATX power supplies. Although

most power supplies generally meet the specifications required by the CPU,

some are inadequate. A 2 amps of current supply on a 5V Standby rail is

strongly recommended.

It is strongly recommended that you use a high quality power supply that

meets 12V ATX power supply Specification 1.1 or above. It is also required

that the 12V 4-pin power connection (J41) be used for high-load configura-

tions. In areas where noisy power transmission is present, you may

choose to install a line filter to shield the computer from noise. It is recom-

mended that you also install a power surge protector to help avoid problems

caused by power surges.

Chapter 1: Introduction

1-13

1-6 Super I/O

The disk drive adapter functions of the Super I/O chip include a floppy disk

drive controller that is compatible with industry standard 82077/765, a data

separator, write pre-compensation circuitry, decode logic, data rate selec-

tion, a clock generator, drive interface control logic and interrupt and DMA

logic. The wide range of functions integrated onto the Super I/O greatly

reduces the number of components required for interfacing with floppy disk

drives. The Super I/O supports two 360 K, 720 K, 1.2 M, 1.44 M or 2.88 M

disk drives and data transfer rates of 250 Kb/s, 500 Kb/s or 1 Mb/s.

It also provides two high-speed, 16550 compatible serial communication

ports (UARTs), one of which supports serial infrared communication. Each

UART includes a 16-byte send/receive FIFO, a programmable baud rate

generator, complete modem control capability and a processor interrupt sys-

tem. Both UARTs provide legacy speed with baud rate of up to 115.2 Kbps

as well as an advanced speed with baud rates of 250 K, 500 K, or 1 Mb/s,

which support higher speed modems.

The Super I/O provides functions that comply with ACPI (Advanced Con-

figuration and Power Interface), which includes support of legacy and ACPI

power management through a SMI or SCI function pin. It also features auto

power management to reduce power consumption.

The IRQs, DMAs and I/O space resources of the Super I/O can be flexibly

adjusted to meet ISA PnP requirements, which support ACPI and APM (Ad-

vanced Power Management).

1-14

P8SGA User’s Manual

Notes

Page is loading ...

Supermicro P8SGA-O User manual

This manual is also suitable for

Supermicro P8SGA-O User manual

Related papers

Other documents