Power Meter Utility
Quick Start Guide
[Version 1.3]
Warning
ICP DAS Inc., LTD. assumes no liability for damages consequent to the use of
this product. ICP DAS Inc., LTD. reserves the right to change this manual at any time
without notice. The information furnished by ICP DAS Inc. is believed to be accurate
and reliable. However, no responsibility is assumed by ICP DAS Inc., LTD. for its
use, or for any infringements of patents or other rights of third parties resulting from
its use.
Copyright and Trademark Information
© Copyright 2012 by ICP DAS Inc., LTD. All rights reserved worldwide.
Trademark of Other Companies
The names used for identification only maybe registered trademarks of their
respective companies.
License
The user can use, modify and backup this software on a single machine. The user
may not reproduce, transfer or distribute this software, or any copy, in whole or in
part.
Table of Contents
1 System Description...................................................................................1
2 Before Installation.....................................................................................2
3 Software Installation..................................................................................3
4 User Interface Introduction .......................................................................5
5 Utility Operation Procedure.......................................................................6
5.1 Change language...........................................................................6
5.2 Establish connection or perform disconnection with the meter ......6
5.2.1 Establish COM Port connection with PM-213x....................6
5.2.2 Establish COM Port connection with PM-311x....................8
5.2.3 Establish TCP/IP Connection with PM-213x-MTCP ..........10
5.2.4 Perform Disconnection......................................................13
5.3 Modify parameters of the power meter.........................................14
5.4 Restore the parameters of the meter to default factory settings...15
Power Meter Utility Quick Start
http://www.icpdas.com
1
1 System Description
This document is intended to provide guidelines for ICP DAS Power Meter
Utility software tool that applies to ICP DAS Power Meter (e.g., PM-213x /
PM-311x / PM-213x-MTCP). This software tool has to be installed on PC and it
enables to retrieve and display the power measurement values that measured
by power meter via COM Port or Ethernet. The users will be able to read the
power measurement values and to perform parameter settings of the meter.
When connecting with PM-213x / PM-311x by RS-485 communication protocol
interface, it requires to convert RS-232 or USB on PC to RS-485
communication interface, converter modules (such as ICP DAS I-7561, I-7520)
might be required； When connecting with PM-213x-MTCP by Ethernet
interface, it must setup the correct IP address to retrieve the power
measurement values easily!
Features：
By Modbus RTU or Modbus TCP protocol, it enables to connect with
ICP DAS Power Meter and data retrieving.
Real time monitor power measurement values of the meter.
Real time setting up parameters of the meter.
Restore the parameters of the meter to default factory settings.
Power Meter Utility Quick Start
http://www.icpdas.com
2
2 Before Installation
Before installing ICP DAS Power Meter Utility, please finishing installation
of the ICP DAS Power Meter hardware, and make sure all wiring
connections are accurate (e.g., please refer to the user manual for
PM-213x / PM-311x / PM-213x-MTCP). The Power Meter Utility requires
the .NET framework version 2.0 to be installed on the target computer.
Please follow the link below to get the framework package directly from
Microsoft, if required.
Download Microsoft .Net Framework Version 2.0：
Link 1:
http://www.microsoft.com/en-us/download/details.aspx?id=1639
Link 2:
http://www.microsoft.com/en-us/download/details.aspx?id=16614
Download Microsoft .Net Framework Version 3.5：
Link 1:
http://www.microsoft.com/en-us/download/details.aspx?id=21
Link 2:
http://msdn.microsoft.com/en-us/vstudio/aa496123
Power Meter Utility Quick Start
http://www.icpdas.com
3
3 Software Installation
Please contact ICP DAS service or visit ICP DAS Intelligence Power Meter
product Web site to obtain the latest version of the ICP DAS Power Meter
Utility installer. Double click the ICP DAS Power Meter Utility installer to
run the installation. Click [Next] to continue.
On [Select Installation Folder] page, input path or browse through file dialog
box to select the destination folder and select the software user option,
click [Next] to continue.
Power Meter Utility Quick Start
http://www.icpdas.com
4
Make sure the settings are accurate. Click [Next] to start installation.
When the installation process is completed, click [Close] to finish installing
program.
After the installation is completed, you will find the Power Meter Utility
Shortcut on the desktop and in the program menu: [Start] [All
Programs][ICPDAS] [ Power Meter] (icon ).
Power Meter Utility Quick Start
http://www.icpdas.com
5
4 User Interface Introduction
Power Meter Utility software tool Interface is shown as follow：
Languages: Select your preferred language for the software interface.
(English, Traditional Chinese, Simplified Chinese).
Connection Setting: Set up related connection parameter settings for
connecting with the power meter.
Real Time Power Measurements: Display power meter measurement
values in real time.
Status information: Display power meter status information.
Connection Setting
Connection SettingConnection Setting
Connection Setting
Status Information
Status InformationStatus Information
Status Information
Real Time
Real Time Real Time
Real Time Power
Power Power
Power M
MM
Measurement
easurementeasurement
easurements
ss
s
Languages
LanguagesLanguages
Languages
Power Meter Utility Quick Start
http://www.icpdas.com
6
5 Utility Operation Procedure
Power Meter Utility makes it easy to retrieve power measurements and
modify parameters for systems in real time when connecting with meters.
Power Meter Utility enables:
Change Language interface for utility user interface.
Establish connection or perform disconnection of the power meter.
Modify parameters of the power meter.
Restore the parameters of the meter to default factory settings.
5.1 Change language
The preferred language can be set by the following steps:
i. Execute Power Meter Utility, and the language change option will
appear on the right upper area of the window.
ii. Click on the preferred language, currently there are 3 language
options: English, Traditional Chinese, and Simplified Chinese.
5.2 Establish connection or perform disconnection with the meter
5.2.1 Establish COM Port connection with PM-213x
i. Because PM-213x support Modbus RTU protocol, select “Modbus
RTU (for PM-213x / PM-311x)” in the Meter Communication
Interface.
ii. Under the Connection Setting section, select the COM Port that is
going to connect with the power meter, input the Timeout interval
(unit : ms) and input the Meter ID number. The default Timeout
interval will be 1000 ms; this value can be modified according to
the quality of the signal in the field.
Power Meter Utility Quick Start
http://www.icpdas.com
7
Note: User can click on “Refresh” button to renew the available
COM Port of the PC system, and then select the COM Port from
the dropdown list.
iii. Make sure the parameters you input are all accurate, and click on
“Connect” button.
iv. When the system is trying to connect with the power meter, the
status information will show message: “Try connecting”. It will try to
connect with the power meter by default factory parameter settings
such as: Baud Rate:19200 and Stop Bits: 1.
v. If the system fails to establish the connection with the power meter
by default factory parameter settings. The system will try other
combination of the Baud Rate and Stop Bits. The status
information will show the Baud Rate and Stop Bits information.
vi. After the utility connecting with the meter, the Meter Parameter
Information section will be renewed (as shown below). And the
real time power measurements will be displayed under the section
of Power Measurements (as shown below).
Power Meter Utility Quick Start
http://www.icpdas.com
8
vii. After the connection has been established and the power
measurements have been read into the system, the status
information will show the time interval the system requires to read
all power measurements. This value can be used as a reference
for connection quality evaluation.
5.2.2 Establish COM Port connection with PM-311x
i. Because PM-311x support Modbus RTU protocol, select “Modbus
RTU (for PM-213x / PM-311x)” in the Meter Communication
Interface.
ii. Under the Connection Setting section, select the COM Port that is
going to connect with the power meter, input the Timeout interval
(unit : ms) and input the Meter ID number. The default Timeout
interval will be 1000 ms; this value can be modified according to
the quality of the signal in the field.
Note: User can click on “Refresh” button to renew the available
COM Port of the PC system, and then select the COM Port from
the dropdown list.
Power Meter Utility Quick Start
http://www.icpdas.com
9
iii. Make sure the parameters you input are all accurate, and click on
“Connect” button.
iv. When the system is trying to connect with the power meter, the
status information will show message: “Try connecting”. It will try to
connect with the power meter by default factory parameter settings
such as: Baud Rate:19200 and Stop Bits: 1.
v. If the system fails to establish the connection with the power meter
by default factory parameter settings. The system will try other
combination of the Baud Rate and Stop Bits. The status
information will show the Baud Rate and Stop Bits information.
vi. After the utility connecting with the meter, the Meter Parameter
Information section will be renewed (as shown below). And the real
time power measurements will be displayed under the section of
Power Measurements (as shown below).
Power Meter Utility Quick Start
http://www.icpdas.com
10
For the PM-311x DO channel attribute setting, it allows user to
modify the DO Relay value and Power On value individually by
clicking on the “ON/OFF” button of specific channel (as shown
below).
vii. After the connection has been established and the power
measurements have been read into the system, the status
information will show the time interval the system requires to read
all power measurements. This value can be used as a reference
for connection quality evaluation.
5.2.3 Establish TCP/IP Connection with PM-213x-MTCP
i. Because PM-213x-MTCP support Modbus TCP protocol, select
“Modbus TCP (for PM-213x-MTCP)” in the Meter Communication
Interface.
ii. Under the Connection Setting section, input the Timeout interval
(unit: ms) and input the Meter ID number. The default Timeout
interval will be 1500 ms; this value can be modified according to
the quality of the signal in the field.
Power Meter Utility Quick Start
http://www.icpdas.com
11
iii. Click “Search” to enter the “Communication Interface Setting”
window, click ”Search” button to search the available power meter.
iv. Select the power meter which you want to modify parameters from
the meter list, then click ”Configuration” button to setup the meter
parameters. After complete all setting, click “OK”, and return to the
meter list windows.
Power Meter Utility Quick Start
http://www.icpdas.com
12
v. Select the power meter which utility will connect with, then click
“OK” button.
vi. Make sure the power meter parameters are all accurate, click
“Connect” button.
vii. When the system is trying to connect with the power meter, the
status information will show “Try connecting” message.
viii. After the utility connect with the meter, the Meter Parameter
Information section will be renewed (as shown below). And the
real time power measurements will be displayed under the section
of Power Measurements (as shown below).
Power Meter Utility Quick Start
http://www.icpdas.com
13
ix. After the connection has been established and the power
measurements have been read into the system, the status
information will show the time interval the system requires to read
all power measurements. This value can be used as a reference
for connection quality evaluation.
5.2.4 Perform Disconnection
To disconnect with the power meter, click on the “Disconnect” button
to stop reading power measurements and interrupt the connection.
Power Meter Utility Quick Start
http://www.icpdas.com
14
5.3 Modify parameters of the power meter
After successfully connecting with the meter via Power Meter Utility, the
user can modify the parameters of the meter. The new settings will take
effect next time when the system trying to establish a connection with the
meter.
To modify the connection parameters, please follow the steps below：
(Using COM Port connection with PM-213x as an example):
i. After successfully connecting with the meter, some parameters input
panel such as Baud Rate, Stop Bits, PT Ratio and CT Ratio will
appear to be available to input.
Select appropriate values from the dropdown list of the Baud
Rate and Stop Bits.
For PT Ratio and CT Ratio, the user can select appropriate
values from the dropdown list or input the value into the panel
directly.
ii. After finishing setting up the parameters of the meter, click on the
“Modify” button to modify the values. The new parameter settings will
take effect in real time. The status information will show “Modifying
Power Meter Parameters…” when performing parameter
modification.
Please Note ：
1. There are only PT Ratio and CT Ratio settings for the COM Port
connection with PM-311x.
2. There are only PT Ratio and CT Ratio settings for the TCP/IP
connection with PM-213x-MTCP.
3. After finishing the modification of the PM-213x connection
parameters (Baud Rate and Stop Bits), the system will
temporarily interrupt the connection with the meter and will
Power Meter Utility Quick Start
http://www.icpdas.com
15
reconnect with the meter again by the new parameter settings. If
the connection is established, the system will real time retrieve
and display all power measurement values. If the system fails to
connect with the meter, it will continue to try to establish the
connection by other Baud Rate and Stop Bits combination.
5.4 Restore the parameters of the meter to default factory settings
After successfully connecting with the meter via Power Meter Utility, the
user can restore the parameters of the meter to default factory settings.
The default factory settings of the PM-213x parameters will be: Baud
Rate: 19200, Stop Bits: 1, PT Ratio: 1 and CT Ratio: 1
The default factory settings of the PM-311x parameters will be: PT
Ratio: 1 and CT Ratio: 1
The default factory settings of the PM-213x-MTCP parameters will be:
PT Ratio: 1 and CT Ratio: 1
Follow steps below to restore the parameters to default factory settings:
i. After successfully connecting with the meter, click on the “Default”
button to restore the parameters of the meter to default factory
settings. After the reset take effect, the PM-213x parameters such as
Baud Rate, Stop Bits, PT Ratio and CT Ratio will appear to be default
factory settings；The PM-311x / PM-213x-MTCP parameters such as
PT Ratio and CT Ratio will appear to be default factory settings.
ii. The status information will show “Return to Default Values” when the
system is trying to restore the parameters of the meter to default
factory settings.
Please Note ：
1. After finishing the modification of the PM-213x connection
parameters (Baud Rate and Stop Bits), the system will
Power Meter Utility Quick Start
http://www.icpdas.com
16
temporarily interrupt the connection with the meter and will
reconnect with the meter again by the new parameter settings. If
the connection is established, the system will real time retrieve
and display all power measurement values. If the system fails to
connect with the meter, it will continue to try to establish the
connection by other Baud Rate and Stop Bits combination.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
ICP DAS USA PM-3112-100-CPS Quick Start
- Type
- Quick Start
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ICP DAS USA PMC-5151 User manual
-
-
-
-
-
-
-
-
-
