Regency PG36LPG5-R Owner's Installation Manual

Brand: Regency

Model: PG36LPG5-R

Category: Fireplaces

Type: Owner's Installation Manual

This manual is also suitable for

Models: PG36NG5-R

PG36LPG5-R

Owners &

Installation

PLEASE KEEP THESE INSTRUCTIONS

FOR FUTURE REFERENCE

Manual

09/11/12

LISTINGS AND CODE APPROVALS

These gas appliances have been tested in

accordance with AS4553, NZS 5262 and

have been certiﬁ ed by the Australian Gas

Association for installation and operation

as described in these Installation and

Operating Instructions.

Your unit should be serviced annually

by an authorised service person.

918-744b

PG36 Gas Log Fireplace

WARNING:

Improper installation, adjustment, alteration,

service or maintenance can cause injury or

property damage. Refer to this manual. For

assistance or additional information consult

an authorised installer, service agency or the

gas supplier.

FOR YOUR SAFETY:

Do not store or use gasoline or other ﬂ ammable

vapours and liquids in the vicinity of this or

any other appliance.

Installation and service must be performed by

an authorised installer, service agency or the

gas supplier.

FOR YOUR SAFETY:

What to do if you smell gas:

Do not try to light any

appliance

Do not touch any electrical

switch: do not use any phone

in your building.

Immediately call your gas

supplier from a neighbour's

phone. Follow the gas

supplier's instructions.

If you cannot reach your

gas supplier, call the ﬁ re

department.

Regency® PG36-5 Gas Log Fireplace

TO THE NEW OWNER:

Congratulations!

You are the owner of a state-of-the-art Gas Log Fireplace by FPI FIREPLACE PRODUCTS INTERNATIONAL

LTD. The PG36 has been designed to provide you with all the warmth and charm of a wood ﬁ replace at the

ﬂ ick of a switch. The model PG36 has been approved by the Australian Gas Association for both safety and

efﬁ ciency. As it also bears our own mark, it promises to provide you with economy, comfort and security for

many trouble free years to follow. Please take a moment now to acquaint yourself with these instructions

and the many features of your Regency® Fireplace.

Regency® PG36-5 Gas Log Fireplace 3

TABLE OF CONTENTS

Lighting Instructions.....................................................31

Resetting The Unit .......................................................31

Shutdown Instructions .................................................31

First Fire ......................................................................31

OPERATING INSTRUCTIONS

Adjusting Flame Height ...............................................32

Summary of Controls ..................................................32

Pilot Adjustment ...........................................................32

Normal Operating Sounds of Gas Appliances .............32

Copy of The Lighting Plate Instructions ......................33

MAINTENANCE

Maintenance Instructions.............................................34

Gold or Brass Louvres & Trim .....................................35

Log Replacement ........................................................35

Glass Gasket ...............................................................35

Door Glass...................................................................35

Removing Valve Tray ...................................................36

Fan Replacement ........................................................37

Manual Control Switch Replacement ..........................38

PARTS LIST

Electronic Components Parts List ...............................39

Main Assembly ............................................................40

Burner Assembly & Log Set.........................................41

Bay Front Assembly.....................................................42

Flush Front Accessories ..............................................43

Premium Flush Front Assembly...................................44

Cast Faceplate Assembly ............................................45

WARRANTY

Warranty ......................................................................47

DATA BADGE

Data Badge....................................................................4

INSTALLATION

Important Message ........................................................5

Before You Start ............................................................5

General Safety Information............................................5

Installation Checklist ......................................................5

Clearances ....................................................................6

Locating Your Fireplace .................................................6

Manufactured Mobile Home Additional Requirements ..6

Combustible Mantels .....................................................7

Mantel Leg Clearances..................................................8

Framing And Finishing ...................................................8

Unit Assembly Prior To Installation ................................9

Flueing Introduction .......................................................9

Exterior Flue Termination Locations ............................10

Flueing .........................................................................11

Simpson Dura-vent Flueing .........................................12

Simpson Dura-vent Flueing Components List .............12

Flueing Arrangements - Horizontal Terminations .........13

Flueing Arrangements - Horizontal Terminations .........14

Flueing Arrangements - Vertical Terminations .............15

Horizontal Terminations ...............................................17

Vertical Terminations ...................................................18

Gas Connection ...........................................................19

Gas Pipe Pressure Testing ..........................................19

Aeration Adjustment ....................................................19

Conversion From NG To LPG ......................................20

Optional Brick Panels ..................................................22

Log Set Installation ......................................................22

Standard Flush Door ...................................................24

Premium Flush Front Installation .................................25

Wiring ..........................................................................29

Remote Control ..........................................................31

Operating Instructions ................................................31

Regency® PG36-5 Gas Log Fireplace

DATA BADGE

This is a copy of the label that accompanies

each PG36 Zero Clearance Room Sealed Gas

Fireplace. We have printed a copy of the contents

here for your review.

DO NOT

OPERATE THIS APPLIANCE BEFORE READING THE

INSTRUCTIONS BOOKLET.

PLACE ARTICLES ON OR AGAINST THIS APPLIANCE

STORE CHEMICALS OR FLAMMABLE MATERIALS

SPRAY AEROSOLS IN THE VICINITY OF THIS

APPLIANCE WHILE IN OPERATION.

OPERATE WITH PANELS, COVERS OR GUARDS

REMOVED FROM THIS APPLIANCE.

ENCLOSE THIS APPLIANCE.

DO NOT MODIFY THIS APPLIANCE.

NEAR THIS APPLIANCE.

DO NOT

908-602a

(Australia Only)

The label is located on the front inside base of the

unit, visible when the bottom louvre is open. DATA BADGE NOTE: Regency® units are

constantly being improved. Check the label on

the unit and if there is a difference, the label on

the unit is the correct one.

Gas Type NG LPG

Model

Gas Consumption 33 . 31 .

Manifold Pressure 1.0 2.6

Injector Size 1x 1x 52

PG36-NG PG36-LPG

mj mj

kPa kPa

Electrical: 240VAC 50Hz 1.0 amp max.

Serial

Number

918-285c

Model

N2134

Regency Gas Fireplace

2.65mm 1.61mm

AGA 5815G

AS4553

262

Distributed by:

Western Australia:

To be installed by an authorised person in

accordance with installation instructions

provided with the appliance.

Air Group Australia

28-30 Division St

Welshpool, WA 6106

Fireplace Products

Australia Pty. Ltd.

21-23 South Link Blvd.

Dandenong, VIC 3175

Eastern Australia:

Regency® PG36-5 Gas Log Fireplace 5

INSTALLATION

CHECKLIST

1) Locate appliance. Refer to the following

sections:

a) Locating Your Gas Fireplace

b) Combustible Mantels

c) Mantel Leg Clearances

d) Framing and Finishing

e) Flueing

2) Assemble Top Standoffs and Top Facing

Support and Side Nailing Strips. Refer to the

"Unit Assembly Prior to Installation" section.

(NOTE: must be done before installing unit

into ﬁ replace.)

3) Install flue, refer to the "Horizontal

Termination" & "Vertical Termination"

sections.

4) Make gas and electrical connections. Test

the pilot. Must be as per diagram. Refer to

the " Pilot Adjustment" section.

5) Install standard and optional features. Refer

to the following sections where applicable:

a. Brick Panels

b. Log Set Installation

c. Flush Door

d. Premium Flush Front

e. Bay Door

f. Hampton Cast Faceplate

g. Hampton Cast Grills

h. Remote Controls

6) Final check.

Before leaving this unit with the customer,

the installer must ensure that the appliance is

ﬁ ring correctly and operation fully explained

to customer.

This includes:

1) Clocking the appliance to ensure the correct

ﬁ ring rate (rate noted on label 30,000 Btu/h)

after burning appliance for 15 minutes.

2) If required, adjusting the primary air to ensure

that the ﬂ ame does not carbon. First allow

the unit to burn for15-20 min. to stabilize.

CAUTION: Any alteration to the product that

causes sooting or carboning that results

in damage is not the responsibility of the

manufacturer.

INSTALLATION

IMPORTANT MESSAGE

SAVE THESE INSTRUCTIONS

The PG36-NG or PG36-LPG Room Sealed

Fireplace must be installed in accordance with

AS5601-2004 and NZS 5261 5261 and these

instructions. Carefully read all the instructions

in this manual ﬁ rst. Consult the "authority

having jurisdiction" to determine the need for

a permit prior to starting the installation. It is

the responsibility of the installer to ensure

this ﬁ replace is installed in compliance with

manufacturer's instructions and all applicable

codes.

BEFORE YOU START

NOTE:

NOT INTENDED AS A FIREPLACE INSERT.

DUE TO HIGH TEMPERATURES, THE

APPLIANCE SHOULD BE LOCATED

OUT OF TRAFFIC AND AWAY FROM

FURNITURE AND DRAPERIES.

INSTALLATION AND REPAIR SHOULD

BE DONE BY A AUTHORISED SERVICE

PERSON. THE APPLIANCE SHOULD

BE INSPECTED BEFORE USE AND AT

LEAST ANNUALLY BY AN AUTHORISED

SERVICE PERSON. MORE FREQUENT

CLEANING MAY BE REQUIRED

DUE TO EXCESSIVE LINT FROM

CARPETING, BEDDING MATERIAL,

ETC. IT IS IMPERATIVE THAT CONTROL

COMPARTMENTS, BURNERS AND

CIRCULATING AIR PASSAGEWAYS

OF THE APPLIANCE BE KEPT CLEAN.

WARNING: FAILURE TO INSTALL THIS

APPLIANCE CORRECTLY WILL VOID

YOUR WARRANTY AND MAY CAUSE A

SERIOUS HOUSE FIRE.

CHILDREN AND ADULTS SHOULD

BE ALERTED TO THE HAZARDS OF

HIGH SURFACE TEMPERATURES,

ESPECIALLY THE FIREPLACE GLASS,

AND SHOULD STAY AWAY TO AVOID

BURNS OR CLOTHING IGNITION.

YOUNG CHILDREN SHOULD BE

CAREFULLY SUPERVISED WHEN

THEY ARE IN THE SAME ROOM AS THE

APPLIANCE.

CLOTHING OR OTHER FLAMMABLE

MATERIAL SHOULD NOT BE PLACED

ON OR NEAR THE APPLIANCE. DO NOT

USE AEROSOLS IN THE VICINITY OF

THIS APPLIANCE.

GENERAL SAFETY

INFORMATION

1) The appliance shall be installed in

accordance with the manufacturer's

installation instructions,local gas ﬁ tting

regulations, municipal building codes,

water supply regulations, electrical wiring

regulations, with AS5601-2004 (AGA gas

installation code) NZS 5261 (New Zealand)

2) Installation and repair should be done

ONLY by an authorised person.

3) THIS APPLIANCE IS NOT INTENDED AS A

FIREPLACE INSERT. DO NOT CONNECT

TO MASONARY FLUE.

4) This appliance must be connected to

the speciﬁ ed ﬂ ue and termination cap

to the outside of the building envelope.

Never ﬂ ue to another room or inside a

building. Make sure that the ﬂ ue is ﬁ tted

as per Flueing instructions.

5) Inspect the ﬂ ueing system annually for

blockage and any signs of deterioration.

6) Flueing terminals shall not be recessed into

a wall or siding.

7) Any safety glass removed for servicing must

be replaced prior to operating the appliance.

8) To prevent injury, do not allow anyone who

is unfamiliar with the operation to use the

ﬁ replace.

9) Wear gloves and safety glasses for protection

while doing required maintenance.

10) Be aware of electrical wiring locations in

walls and ceilings when cutting holes for

termination.

11) Under no circumstances should this

appliance be modiﬁ ed. Parts that have to be

removed for servicing should be replaced

prior to operating this appliance.

12) Installation and any repairs to this appliance

should be done by an authorised service

person. An authorised service person should

be called to inspect this appliance annually.

Make it a practice to have all of your gas

appliances checked annually.

13) Do not slam shut or strike the glass door.

14) Under no circumstances should any solid

fuels (wood, paper, cardboard, coal, etc.)

be used in this appliance.

15) The appliance area must be kept clear and

free of combustible materials, (gases and

other ﬂ ammable vapours and liquids).

Regency® PG36-5 Gas Log Fireplace

INSTALLATION

Clearances for Bay or Flush Front

NOTE: The minimum ﬂ oor clearance must

be maintained from the top surface of the

carpeting, tile, etc.

Minimum Clearance from Top of Unit to:

Mantel* Minimum 7" (177mm)

Ceiling from top of unit. 32" (1016mm)

Side Wall Clearance

Bay or Flush Front 6" (152mm)

Horizontal Flue Clearances

Top 2" (51mm)

Side 1-1/2" (38mm)

Bottom 1-1/2" (38mm)

Vertical Flue Clearances 1-1/4" (32mm)

Alcove Clearances**:

Max. Depth 36" (914mm)

Min. Width 48" 1219mm)

Min. Height 72" 1829mm)

* see mantle clearance instructions

(Refer to the "Combustible Mantels," & "Mantel

Leg Clearances" sections.)

CLEARANCES

The clearances listed below are Minimum

distances unless otherwise stated:

A major cause of chimney related ﬁ res is

failure to maintain required clearances (air

space) to combustible materials. It is of the

greatest importance that this ﬁ replace and

ﬂ ue system be installed only in accordance

with these instructions.

Clearance to Combustibles from:

Back 0" (0mm)

Side 0" (0mm)

Floor 0"

(0mm)

Diagram 1

LOCATING YOUR

FIREPLACE

1) When selecting a location for your ﬁ replace,

ensure that the clearances outlined on this

page are met.

2) Provide adequate clearances for servicing.

3) The appliance must be installed on a ﬂ at,

solid, continuous surface (e.g. wood, metal,

concrete). This may be the ﬂ oor, or raised up

on a platform to enhance its visual impact.

If the appliance is going to be installed

on carpeting, combustible linoleum tile or

other combustible material other than wood

ﬂ ooring, the appliance must be installed on

a metal or wood panel extending the full

width and depth of the appliance.

4) The PG36 Co Axial Flue Gas Fireplace

can be installed in a recessed position or

framed out into the room as in A, B, C, D.

See Diagram 1.

5) This appliance is Listed for bedroom

installations when used with a Listed Millivolt

Thermostat. Some areas may have further

requirements, check local codes before

installation.

6) The PG36 Co Axial Flue Gas Fireplace is

approved for alcove installations, which

meet the clearances listed on this page.

7) We recommend that you plan your installation

on paper using exact measurements for

clearances and ﬂ oor protection before

actually installing this appliance. Have an

authorized inspector, dealer, or installer

review your plans before installation.

Note: For ﬂ ue terminations see the "Exterior

Flue Termination Locations" section.

MANUFACTURED

MOBILE HOME

ADDITIONAL

REQUIREMENTS

1) Ensure that structural members are not cut

or weakened during installation.

2) Ensure proper grounding using the #8

ground lug provided. Refer to the "Wiring"

section.

A) Flat on Wall

B) Flat on Wall Corner

C) Recessed into Wall/Alcove

D) Corner

WARNING

Fire hazard is an extreme

risk if these clearances

are not adhered to.

Regency® PG36-5 Gas Log Fireplace 7

INSTALLATION

Due to the extreme heat this ﬁ replace emits, the mantel clearances are critical. Combustible mantel clearances from the top of unit are shown

in the diagrams below.

COMBUSTIBLE MANTELS

These drawings are to scale at 1:6 (one inch = 6 inches)

Mantel can be installed anywhere in shaded area or higher using the

above scale.

Note: Ensure the paint that is used on the mantel and the facing

is "heat resistant" or the paint may discolour.

Note: A non-combustible mantel may be installed at a lower

height if the framing is made of metal studs covered with

a non-combustible board.

Regency® PG36-5 Gas Log Fireplace

INSTALLATION

Note: 40-1/2" (1029mm) is the minimum

height for both ﬂ ex termination or

Simpson Dura-Vent ﬂ ueing.

MANTEL LEG

CLEARANCES

Combustible mantel leg clearances as per

diagram below:

FRAMING AND

FINISHING

1) Determine the total thickness of facing

material (e.g. drywall plus ceramic tiles) to

allow the ﬁ nished surface to be ﬂ ush with

the front of the unit. Total facing thickness

can vary from 1/2" (13mm) to 1-1/4" (32mm)

thick.

152m m Side Wall

127m m

51m m

Mantel leg

P36

Fire p lace

Allow able m antel leg

projection.

76m m

38m m

Maximum

38mm

projection

at 51mm

minimum

clearance.

Note:The unit does not have to be completely

enclosed in a chase. The clearance on

top of the unit is 0" to the standoffs so

combustible building materials can be

laid directly on top of the standoffs. You

must maintain 1-1/2" (38mm) clearance

from the ﬂ ue to combustible materials

for ﬂ ex (1-1/4" (32mm) for Simpson

Dura-Vent).

5) Use steel studs for framing where the

1-1/2" (38mm) clearance from the ﬂ ue to

combustible material cannot be maintained,

e.g. front top header.

2) Frame in the enclosure for the unit with

framing material.

12-3/4"

(324mm)

3-1/2"

(89mm)

(102mm)

2”

(51mm)

40-1/2" (1029mm)

36" (914mm)

32-1/2" (826mm)

10" (254mm) dia. hole

through wall for Flex

or for DuraVent

Top Header

Opening for gas

connection

1/2"

(13mm)

Drywall

Install Side Nailing Strips, Top Facing

Support, and Top Standoffs before

unit is slipped into position. See "Unit

Assembly Prior to Installation" section

for assembly details.

NOTE:

When using the Premium Flush Front

option, a ﬁ nishing trim (962mm cover)

needs to be installed to cover the

spacers.

Maintain a physical gap between lining

and spacers 2-5mm. (5mm clearance to

framing each side).

Standard Framing Dimensions

A B C D

36-1/4" 36-1/4" 12-3/4" 46"*

921mm 921mm 324mm 1126mm*

Framing Dimensions with

Premium Flush Front Option

A B C D

37-1/4" 37-1/4" 17-3/8" 46-1/2"*

944mm 946mm 432mm 1182mm*

* 'D' is Minimum height to combustible mate-

rials including the Minimum 2" (51mm) Top

clearance to the Horizontal Flue, see ﬂ ue

clearances in section "Clearances."

3) For exterior walls, insulate the enclosure to

the same degree as the rest of the house,

apply vapour barrier and drywall, as per

local installation codes. (Do not insulate

the ﬁ replace itself.)

4) The top of the unit must not be closer than

32" (813mm) to the ceiling.

Premium Flush Front Framing

Do not use combustible material as lining (eg.

timber) around the ﬁ replace as shown in the

shaded area in the diagram below.

Regency® PG36-5 Gas Log Fireplace 9

INSTALLATION

FLUEING

INTRODUCTION

The PG36 uses the "balanced ﬂ ue" technology

Co Axial system. The inner liner ﬂ ues products

of combustion to the outside while the outer

liner draws outside combustion air into the

combustion chamber thereby eliminating the

need to use heated room air for combustion and

losing warm room air up the chimney.

Note: These flue pipes must not be

connected to any other appliance.

The gas appliance and ﬂ ue system must be

ﬂ ued directly to the outside of the building,

and never be attached to a chimney serving a

separate solid fuel or gas burning appliance.

Each Co Axial Flue gas appliance must use

it's own separate ﬂ ue system. Common ﬂ ue

systems are prohibited.

Before the unit is slid into position, install the

provided spacers to the side of the ﬁ replace

as follows;

1) Align the screw locations on spacer with

screw locations on the side of the ﬁ rebox

and secure in place using 3 screws.

2) Repeat for other side.

NOTE: The side nailing strips are to be in-

stalled to the spacer after the spacer

is attached to the unit.

Spacer

Left Side Shown

Premium Flush Front

Spacer Installation

Side

Nailing Strips

"C" Screw Position:

For a facing material depth of 1-1/4" (32mm),

the top facing support must be reversed.

UNIT ASSEMBLY

PRIOR TO

INSTALLATION

The Top Facing Support, the Side Nailing Strips

and the 2 Top Standoffs must be correctly

positioned and attached to the top before unit

is slipped into position.

Top Standoff Assembly

The top standoffs are shipped in a ﬂ at position

and must be folded into shape and attached.

1) Remove the standoffs from the ﬁ replace top.

2) Take each standoff and bend into the correct

shape. Bend up at the bend lines until the

screw holes in the standoff and the pre-

punched screw holes on the ﬁ replace top

line up.

3) Attach the standoff securely to the top with

2 screws per standoff (on opposite corners).

Top Facing Support

Side Nailing Strips

Determine the total thickness of facing material

(e.g. drywall plus ceramic tiles) to allow the

ﬁ nished surface to be ﬂ ush with the front of the

unit. Total facing thickness can vary from 1/2"

(13mm) to 1-1/4" (32mm) thick.

The Top Facing Support can be mounted in 3

different positions depending on the thickness

of the facing material.

2) Fold out the two nailing strips on each side.

Screw

Position Facing Material

Depth

A 1/2" / 13mm

B 7/8" / 22mm

C* 1-1/4" / 32mm

* For "C" screw position the top facing

support is reversed.

1) Mount Top Facing Support using the 3

supplied screws into the three pre-punched

screw holes on the top front of the unit. Use

hole positions A, B, or C depending on your

facing depth.

Regency® PG36-5 Gas Log Fireplace

INSTALLATION

EXTERIOR FLUE TERMINATION LOCATIONS

Minimum clearances required for balanced ﬂ ue terminals or

the ﬂ ue terminals of outdoor appliances

according to AS5601-2004 (AGA gas installation code) or NZS 5261 (New Zealand)

Minimum

Clearance (mm)

a Below eaves, balconies or other projections:

- Appliances up to 50 MJ/h input 300

- Appliances over 50 MJ/h input 500

b From the ground or above a balcony 300

c From a return wall or external corner 500

d From a gas meter (M) 1000

e From an electricity meter or fuse box (P) 500

f From a drain or soil pipe 150

g Horizontal from any building structure (unless appliance is approved

for closer installation) or obstruction facing a terminal 500

h From any other ﬂ ue terminal, cowl or combustion air intake 500

j Horizontally from an openable window, door, or non-mechanical air inlet, or

any other opening into a building, with the exception of sub-ﬂ oor ventilation

(see also Note (I)):

- Appliances up to 150 MJ/h input 500

- Appliances over 150 MJ/h input 1500

k Vertically below an openable window, door, or non-mechanical air inlet,

or any other opening into a building, with the exception of sub-ﬂ oor ventilation

(see also Note (I)): see table below

Clearance 'k' in mm

Space Heaters All Other Appliances

Up to 50 MJ/h Up to 50 MJ/h input Over 50 MJ/h input Over 150 MJ/h input

input to 150 MJ/h input

150 500 1000 1500

NOTES:

(I) For mechanical air inlets, including spa blowers, the clearance 'j' and 'k' shall be 1500 mm in all cases.

(II) All distances shall be measured vertically or horizontally along the wall to a point in line with the nearest par to of the terminal.

(III) Prohibited area below electricity meter or fuse box extends to ground level.

(IV) A ﬂ ue terminal of this type shall not be located under a roofed area unless the roofed area is fully open on at least two sides and a free ﬂ ow

of air at the appliance is achieved.

Regency® PG36-5 Gas Log Fireplace 11

INSTALLATION

FLUEING

Regency® Direct Vent System (Flex)

Horizontal Terminations Only

These ﬂ ueing systems, in combination with the PG36 Room Sealed Gas Fireplace, have been tested and listed as a Direct Vent type ﬂ ue system

by the Australian Gas Association. The location of the termination cap must conform to the requirements in the Flue Terminal Locations diagram in

the "Exterior Flue Termination Locations" section.

Regency® Direct Vent (Flex) System Termination Kit (Part # 946-515) includes all the parts needed to install the PG36 with a maximum

run of 1200mm.

1) 175mm dia. ﬂ exible liner (1200mm length)

2) 100mm dia. ﬂ exible liner (1200mm length)

3) spring spacers (4)

4) thimble (2)

5) AstroCap termination cap (1)

6) screws (12)

7) tube of Mill Pac (1)

8) plated screws (8)

9) screws #8 x 1-1/2" Drill Point, Stainless

Steel (4)

If longer runs are needed, the Regency®

Direct Vent system (Flex) # 946-516 includes

all the parts needed to install the PG36 with

a maximum 3.0m run.

1) 175mm dia. ﬂ exible liner (3.0m length)

2) 100mm dia. ﬂ exible liner (3.0m length)

3) spring spacers (7)

4) thimble (2)

5) AstroCap termination cap (1)

6) screws (12)

7) tube of Mill Pac (1)

8) plated screws (8)

9) screws #8 x 1-1/2" Drill Point, Stainless

Steel (4)

Notes:

1) Liner sections should be continuous without any joints or seams.

2) Only Flex pipe purchased from Regency® may be used for Flex installations.

3) If you are installing the PG36 into a Regency® Mantel Kit, use the minimum horizontal vent height (centre-line of 1029mm). Remember

to include the mantel base in your calculations and to maintain the 32mm clearance (38mm with Flex) to the underside of the mantel

top.

6-7/8"

(173mm)

dia. Flue pipe

4" (102mm)

dia. flue pipe

spring spacer

Termination Cap

(Part# 946-578/P)

AstroCap

(patented)

Wall Thimble

Regency® PG36-5 Gas Log Fireplace

Flue Adapter

(Part# 510-994)

Pipe Length

Round Support

Box/Wall Thimble

(Part # 940)

Round

Support Box/

Wall Thimble

(Part # 940)

Vertical

Terminal

Storm Collar

Part # 953

Flashing

943 or 943S

Ceiling Firestop

(Part # 963)

24" (610mm)

Pipe Length

Adj.Pipe Length

11" - 14-5/8"

(279mm - 372mm)

90 Elbow

AstroCap

Wall Thimble

Part # 942

Vinyl Siding

Standoff (Optional)

Part #950

INSTALLATION

Simpson Dura-Vent

Co-Axial Flue GS

SIMPSON DURA-VENT FLUEING

Horizontal or Vertical Terminations

The Simpson Dura-Vent Co Axial Flue System offers a complete line of component parts for installation of both horizontal and vertical installations. Many

items are offered in decorative black, as well as galvanized ﬁ nish. We recommend using the galvanized ﬁ nish for installation with the PG36.

The minimum components required for a basic

horizontal termination are:

1 Horizontal Termination Cap

1 90o Elbow

1 Flue Adaptor

1 Wall Thimble

1 Length of pipe to suit wall thickness

(see chart)

If a Vinyl Siding Standoff is required (it must

be used with vinyl siding), measure to outside

surface of wall without siding and add 2

inches.

SIMPSON DURA-VENT FLUEING COMPONENTS LIST

All Simpson Dura-Vent components are available directly from Masport.

971 Horiz. Termination Kit includes: 90o black

elbow, wall thimble cover, horiz. square

termination cap, 24" black pipe, and 11"

-14" 5/8" adjustable black pipe

970 Basic Horiz. Termination. Kit includes:

o black elbow, wall thimble cover,

horiz. square termination cap

978 Vert. Termination Kit includes 0/12 -

6/12 pitch adjustable ﬂ ashing, storm

collar, low proﬁ le term. cap

908B 6" (152mm) Pipe Length - Black

907B 9" (229mm) Pipe Length - Black

906 12" (305mm) Pipe Length - Galv.

906B 12" (305mm) Pipe Length - Black

904 24" (610mm) Pipe Length - Galv.

904B 24" (610mm) Pipe Length - Black

903 36" (914mm) Pipe Length - Galv.

903B 36" (914mm) Pipe Length - Black

902 48" (1219mm) Pipe Length - Galv.

902B 48" (1219mm) Pipe Length - Black

911B 11"-14 5/8" (279mm - 372mm) Adjustable

Pipe Length - Black

917B 17"- 24" (432mm - 610mm) Adjustable

Length - Black

945 45O Elbow - Galv.

945B 45O Elbow - Black

945G 45O Elbow - Swivel - Galv.

945BG 45O Elbow - Swivel - Black

990 90O Elbow - Galv.

990B 90O Elbow - Black

990G 90O Elbow - Swivel - Galv.

990BG 90O Elbow - Swivel - Black

991 High Wind Termination Cap (Vertical)

980 Vertical Termination Cap

984 Horizontal Square Termination Cap

985 Horiz. Square High Wind

Termination Cap

982 Snorkel - 14"(356mm) Rise Term.Cap

981 Snorkel - 36" (914mm) Rise

Termination Cap

940 Wall Thimble - Support/Box

941 Cathedral/Ceiling - Support/Box

3951 Brass Trim for Wall Thimble/

Ceiling Sup.

963 Firestop Spacer

943 Flashing 0/12-6/12

943S Flashing 7/12-12/12

953 Storm Collar

950 Vinyl Siding Standoff

988 Wall Strap

942 Wall Thimble

Parts not supplied by Dura-Vent

946-506/P Flue Guard (Optional)

510-994 Dura-Vent Flue Adaptor

640-530/P Riser Flue Terminal

946-205 Vinyl Siding Shield for Riser Flue

Terminal

Part # Description Part # Description Part # Description

Flat Wall Installation

Wall Thickness

(inches) Vent Length Required

(inches)

4" - 5-1/2" 6"

7" - 8-1/2" 9"

10" - 1-1/2" 12"

9" - 14-1/2" 11" - 14-5/8" Adj. Pipe

15" - 23-1/2" 17" - 24" Adj.

Corner Installation

Wall Thickness

(inches) Vent Length Required

(inches)

3-1/4" - 6-3/4" 11" - 14-5/8" Adj. Pipe

7-3/4" - 16-1/4" 17" - 24" Adj. Pipe

7-1/4" - 8-3/4" 6" + 12"

9" + 9"

4-1/4" - 5-3/4" 6" + 9"

Wall thickness is measured from the back

standoffs to the inside mounting surface of

termination cap. For siding other than vinyl furring

strips may be used, instead of the vinyl siding

standoff, to create a level surface to mount the

ﬂ ue terminal. The Terminal must not be recessed

into siding. Measure the wall thickness including

furring strips.

Regency® PG36-5 Gas Log Fireplace 13

INSTALLATION

3.5

5.5

4.5

1.5

0.5

2.5

3.5

1.5

0.5

2.5

1029mm

Minimum

Height

Requirement

Meters

FLUEING ARRANGEMENTS - HORIZONTAL TERMINATIONS

SIMPSON DURA-VENT DIRECT FLUE GS SYSTEM and

REGENCY® DIRECT FLUE SYSTEM (FLEX)

(LPG & NG)

The diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 90o elbow (two 45o elbows equal

one 90o elbow).

Note: Must use optional ﬂ ue adapter (Part # 510-994) when using Simpson Dura-Vent pipe.

Simpson Dura-Vent

4" (102mm) inner diameter

6-5/8" (168mm) outer diameter

Regency® Flex Vent

4" (102mm) inner diameter

6-7/8" (175mm) outer diameter

• Maintain clearances to combustibles as listed in the "Clearances," "Locating Your Gas Fireplace," "Combustible Mantels,"

"Mantel Leg Clearances" & "Framing and Finishing" sections.

• Horizontal ﬂ ue must be supported every 3 feet (0.9 meters).

• Firestops are required at each ﬂ oor level and whenever passing through a wall.

A ﬂ ue guard should be used whenever

the termination is lower than the

speciﬁ ed minimum or as per local

codes.

Note: Regency® Co Axial Flue System

(Flex) is only approved for

horizontal terminations.

Regency® PG36-5 Gas Log Fireplace

FLUEING ARRANGEMENTS - HORIZONTAL TERMINATIONS

SIMPSON DURA-VENT DIRECT FLUE GS SYSTEM and

REGENCY® CO AXIAL FLUE SYSTEM (FLEX)

(LPG & NG)

The diagram below shows examples of horizontal termination arrangements using two 90o elbows (two 45o elbows equal one 90o elbow).

Note: 1) A maximum of two 90o elbows are permitted.

2) A minimum of 6 ft. (1.8m) vertical from base of unit is required if two 90o elbows are used.

3) Minimum distance between elbows is 2 ft. (0.6m).

4) Determine the permitted range of horizontal termination arrangements by using chart in the "Simpson Dura-Vent

Flueing" section and deducting 3 ft. (0.9m) from the maximum horizontal distance for the second 90o elbow.

Simpson Dura-Vent

4" (102mm) inner diameter

6-5/8" (168mm) outer diameter

• Maintain clearances to combustibles as listed in the "Clearances," "Locating Your Gas Fireplace," "Combustible Mantels," "Mantel

Leg Clearances" & "Framing and Finishing" sections.

• Horizontal ﬂ ue must be supported every 3 feet (0.9 meters).

• Firestops are required at each ﬂ oor level and whenever passing through a wall.

A ﬂ ue guard should be used whenever the

termination is lower than the speciﬁ ed minimum

or as per local codes.

If length "B" is increased, length "A" must be

decreased by a corresponding amount.

INSTALLATION

Regency® PG36-5 Gas Log Fireplace 15

INSTALLATION

FLUEING ARRANGEMENTS - VERTICAL TERMINATIONS

SIMPSON DURA-VENT CO AXIAL FLUE GS SYSTEM (LPG & NG)

The PG36 is approved for a 23 ft. (7.0m) vertical, with a maximum 12 ft. (3.7m) horizontal offset using

two 90o elbows (two 45o elbows equal one 90o elbow) with Simpson Dura-Vent Co Axial Flue GS ﬂ ue

systems for LPG and NG, as per diagram 1.

The PG36 is approved for a 37 ft. (11.3m) straight vertical, including a 20" (0.5m) horizontal offset

using two 90o elbow (two 45o elbows equal one 90o elbow) with Simpson Dura-Vent Co Axial Flue

GS ﬂ ue systems for LPG and NG, as per the diagram 2.

• Flue must be supported at offsets

• Maintain clearances to combustibles as listed in the "Clearances," "Locating Your Gas

Fireplace," "Combustible Mantels," "Mantel Leg Clearances" & "Framing and Finishing"

sections.

Note: Must use optional ﬂ ue adapter when using Simpson Dura-Vent pipe

(Part # 510-994).

Note: Regency® Co Axial Flue System (Flex) is only approved for horizontal terminations.

Diagram 1 Diagram 2

Regency® PG36-5 Gas Log Fireplace

The PG36 is approved for a 37 ft. (11.3m) straight vertical, with Simpson

Dura-Vent Co Axial Flue GS ﬂ ue systems for LPG and NG, as per the

diagram 3.

The shaded area in the diagram 3 shows all allowable combinations of straight

vertical and offset to vertical terminations with Simpson Dura-Vent Co Axial

Flue GS ﬂ ue systems for LPG and NG. Maximum two 45o elbows allowed.

• Flue must be supported at offsets

• Firestops are required at each ﬂ oor level and whenever passing

through a wall.

• Maintain clearances to combustibles as listed in the "Clearances,"

"Locating Your Gas Fireplace," "Combustible Mantels," "Mantel Leg

Clearances" & "Framing and Finishing" sections.

Diagram 3

INSTALLATION

Regency® PG36-5 Gas Log Fireplace 17

INSTALLATION

Diagram 5

8) Slide the appliance and ﬂ ue assembly

towards the wall carefully inserting the

ﬂ ue pipe into the ﬂ ue cap assembly. It is

important that the ﬂ ue pipe extends into

the ﬂ ue cap sufﬁ cient distance so as to

result in a minimum pipe overlap of 1-1/4

inches. Secure the connection between the

ﬂ ue pipe and the ﬂ ue cap by attaching the

two sheet metal strips extending from the

ﬂ ue cap assembly into the outer wall of the

ﬂ ue pipe. Use the two sheet metal screws

provided to connect the strips to the pipe

section. See Diagram 4.

9) Install wall thimble in the center of the

10" square and attach with wood screws

(Diagram 5).

HORIZONTAL

TERMINATIONS

Install the ﬂ ue system according to the

manufacturer's instructions included with

the components.

1) Set the unit in its desired location. Check to

determine if wall studs or roof rafters are in

the way when the ﬂ ueing system is attached.

If this is the case, you may want to adjust

the location of the unit. Rough in the gas

preferably on the right side of the unit and

the electrical (junction block is on the left

side) on the left.

2) Co Axial Flue pipe and ﬁ ttings are designed

with special twist-lock connections to connect

the ﬂ ueing system to the appliance ﬂ ue outlet.

A twist-lock appliance adaptor is an available

option that must be used in conjunction with

the Simpson Dura-Vent Co Axial Flue GS

system.

3) Put a bead of silicone inside the outer section

of the adapter and a bead of Stove Mate on

the inner collar. Slip the adapter over the

existing inner and outer ﬂ ue collar and fasten

to the outer collar only with the 3 supplied

screws (drilling pilot holes will make this

easier). Level the ﬁ replace and fasten it to

the framing using nails or screws through

the nailing strips.

4) Assemble the desired combination of pipe

and elbows to the appliance adaptor and

twist-lock for a solid connection.

Note:

a) Twist-lock procedure: Four indentations,

located on the female ends of pipes and

ﬁ ttings, are designed to slide straight

onto the male ends of adjacent pipes

and ﬁ ttings, by orienting the four pipe

indentations so they match and slide

in to the four entry slots on the male

ends, Diagram 1. Push the pipe sections

completely together, then twist-lock

one section clockwise approximately

one-quarter turn, until the two sections

are fully locked. The female locking lugs

will not be visible from the outside, on

the Black Pipe or ﬁ ttings. They may be

located by examining the inside of the

female ends.

Diagram 1

b) Horizontal runs of flue must be

supported every three feet. Wall straps

are available for this purpose.

5) Mark the wall for a 10" x 10" (254mm x

254mm) square hole. The center of the

square hole should line up with the centerline

of the horizontal pipe. Cut and frame the 10

inch (254mm) square hole in the exterior

wall where the ﬂ ue will be terminated. If the

wall being penetrated is constructed of non-

combustible material, i.e. masonry block or

concrete, a 7"(178mm) dia. (7-1/2"(191mm)

dia. for ﬂ ex) hole is acceptable.

Diagram 2

Note:

a) The horizontal run of ﬂ ue must be level,

or have a 1/4 inch (6mm) rise for every 1

foot (.3m) of run towards the termination.

Never allow the ﬂ ue to run downward.

This could cause high temperatures and

may present the possibility of a ﬁ re.

b) The location of the horizontal flue

termination on an exterior wall must meet

all local and national building codes, and

must not be blocked or obstructed. For

External Flue Terminal Locations, see

diagram in the "Exterior Flue Termination

Locations" section.

6) The arrow on the flue cap should

be pointing up. Insure that the 1-1/2"

clearances to combustible materials are

maintained. Install the termination cap,

diagram 5.

The four wood screws provided should

be replaced with appropriate fasteners for

stucco, brick, concrete, or other types of

sidings.

Note: If installing termination on a siding

covered wall, a vinyl siding standoff

or furring strips must be used to

ensure that the termination is not

recessed into the siding.

7) Before connecting the horizontal run of

ﬂ ue pipe to the ﬂ ue termination, slide the

Wall Thimble (Part # 620-926) over the ﬂ ue

pipe.

Note: Apply sealant "Mill-Pac" to inner

pipe and high temperature silicone

sealant to outer pipe on every twist-

lock joint.

Note: With Dura-Vent,

the minimum

height is

achieved by

installing a 90o

elbow directly

to the flue

adaptor.

Diagram 4

Diagram 3

Regency® PG36-5 Gas Log Fireplace

Offset Chart

Galvanized pipe is desirable above the rooﬂ ine

due to its higher corrosion resistance. Continue

to add pipe sections through the ﬂ ashing until

the height of the ﬂ ue cap meets the minimum

height requirements speciﬁ ed in Diagram 5 or

local codes. Note that for steep roof pitches,

the vertical height must be increased. A poor

draft, or down drafting can result from high wind

conditions near big trees or adjoining roof lines,

in these cases, increasing the ﬂ ue height may

solve the problem.

7) Ensure ﬂ ue is vertical and secure the base

of the ﬂ ashing to the roof with rooﬁ ng rails,

slide storm collar over the pipe section and

seal with a mastic.

8) Install the vertical termination cap by twist-

locking it.

Note: Any closets or storage spaces, which

the ﬂ ue passes through must be

enclosed.

Diagram 3

Diagram 5

Diagram 1

Diagram 2

Note: Apply sealant "Mill-Pac" to inner pipe

and high temperature silicone seal-

ant to outer pipe on every twist-lock

joint.

VERTICAL

TERMINATIONS

1) Maintain the 1-1/4" (32mm)

clearances (air spaces) to

combustibles when passing

through ceilings, walls, roofs,

enclosures, attic rafter, or other

nearby combustible surfaces.

Do not pack air spaces with

insulation. Check seciotn

"Simpson Dura-vent Flueing"

for the maximum vertical rise of

the ﬂ ueing system and the

maximum horizontal offset

limitations.

2) Set the gas appliance in its

desired location. Drop a

plumb bob down from the

ceiling to the position of

the appliance ﬂ ue exit, and mark the location

where the ﬂ ue will penetrate the ceiling. Drill

a small hole at his point. Next, drop a plumb

bob from the roof to the hole previously

drilled in the ceiling, and mark the spot where

the ﬂ ue will penetrate the roof. Determine

if ceiling joists, roof rafters o r

other framing will obstruct the

ﬂ ueing system.

You may wish

to relocate the

appliance or to

offset, as shown

in Diagram 2

to avoid cutting

load bearing

members.

3) A Firestop spacer must be installed in the

ﬂ oor or ceiling of every level. To install the

Firestop spacer in a ﬂ at ceiling or wall,

cut a 10 inch square hole. Frame the hole

as shown in Diagram 3 and install the

ﬁ restop.

4) Assemble the desired lengths of pipe and

elbows. Ensure that all pipes and elbow

connections are in the fully twist-locked

position and sealed.

5) Cut a hole in the roof centered on the small

drilled hole placed in the roof in Step 2. The

hole should be of sufﬁ cient size to meet

the minimum requirements for clearance

to combustibles of 1-1/2" (38mm). Slip the

ﬂ ashing under the shingles (shingles should

overlap half the ﬂ ashing) as per Diagram

Roof Pitch Minimum Flue Height

Feet Meters

ﬂ at to 7/12 2 0.61

over 7/12 to 8/12 2 0.61

over 8/12 to 9/12 2 0.61

over 9/12 to 10/12 2.5 0.76

over 10/12 to 11/12 3.25 0.99

over 11/12 to 12/12 4 1.22

over 12/12 to 14/12 5 1.52

over 14/12 to 16/12 6 1.83

over 16/12 to 18/12 7 2.13

over 18/12 to 20/12 7.5 2.29

over 20/12 to 21/12 8 2.44

Diagram 4: The upper half of the ﬂ ashing is

installed under the rooﬁ ng material and not

nailed down until the chimney is installed. This

allows for small adjustments.

6) Continue to assemble pipe lengths.

Note: If an offset is necessary in the attic

to avoid obstructions, it is important

to support the ﬂ ue pipe every 3 feet,

to avoid excessive stress on the

elbows, and possible separation.

Wall straps are available for this

purpose (Diagram 2).

INSTALLATION

Regency® PG36-5 Gas Log Fireplace 19

INSTALLATION

PG36-NG4 System Data

For 0 to 4500 feet altitude

Burner Inlet Oriﬁ ce Sizes: #37( 2.65mm)

Max. Input Rating 33 mj

Min. Input Rating 20 mj

Supply Pressure min.1.13 kPa

Manifold Pressure

(High) 0.9 kPa

Electrical: 240 V A.C. System.

Circulation Fan: variable speed 240 CFM.

Log Set: Ceramic ﬁ bre, 7 per set.

Flue System: Simpson Dura-Vent Direct

Vent System or Regency® Direct

Vent System (Flex)

PG36-LPG4 System Data

For 0 to 4500 feet altitude

Burner Inlet Oriﬁ ce Sizes: #52 (1.61mm)

Max. Input Rating 31 mj

Min. Input Rating 18 mj

Supply Pressure min 2.75 kPa

Manifold Pressure

(High) 2.6 kPa

Electrical: 240 V A.C. System.

Circulation Fan: variable speed 240 CFM.

Log Set: Ceramic ﬁ bre, 7 per set.

Flue System: Simpson Dura-Vent Co Axial

Flue System AERATION

ADJUSTMENT

The air shutter can be adjusted by moving the

adjusting wire up or down. The wire is accessed

through the bottom louvre opening. Open the air

shutter for a blue ﬂ ame or close for a yellower

ﬂ ame. The burner aeration is factory set but

may need adjusting due to either the local gas

supply or altitude. This adjustment is performed

by the gas ﬁ tter.

Minimum Air Shutter Opening:

8 mm NG

Full Open LPG

CAUTION: Carbon will be produced if air shutter

is closed too much.

Note: Any damage due to carboning

resulting from improperly setting

the aeration controls is NOT covered

under warranty.

Closed - Tall yellow

Open - Short Blue

GAS CONNECTION

The gas line should be rigid pipe. Copper may

also be used if approved by AS5601-2004.

The gas connection at the valve is 1/2 male.

For minimum and maximum supply pressure

see the System Data Table.

GAS PIPE PRESSURE

TESTING

The appliance must be isolated from the gas

supply piping system by closing its individual

manual shut-off valve during any pressure

testing of the gas supply piping system at test

pressures equal to or less than 1/2 psig. (3.45

kPa). Disconnect piping from valve at pressures

over 3.45 kPa (14" w.c.).

The manifold pressure is controlled by a regulator

built into the gas control, and should be checked

at the pressure test point.

Note: To properly check gas pressure,

both inlet and manifold pressures

should be checked using the valve

pressure ports on the valve.

1) Make sure the valve is in the "OFF"

position.

2) Loosen the "IN" (# 3) and/or "OUT" (# 4)

pressure tap(s), turning counterclockwise

with a 1/8" wide ﬂ at screwdriver.

3) Attach manometer to "IN" and/or "OUT"

pressure tap(s) using a 5/16" (8mm) ID

hose.

4) Seal and or check the pilot outlet (# 8)

5) The pressure check should be carried out

with the unit burning and the setting should

be within the limits speciﬁ ed on the safety

label.

6) When ﬁ nished reading manometer, turn

off the gas valve, disconnect the hose and

tighten the screw (clockwise) with a 1/8" ﬂ at

screwdriver. Screw should be snug, but do

not over tighten.

EV1

EV2

R.Q.

ADJ.

P.OUT

4321

SIT 845 VALVE DESCRIPTION

1) On-Off Solenoid Valve EV1

2) On-Off Solenoid Valve EV2

3) Inlet Pressure Test Point

4) Outlet Pressure Test Point

5) Connection for Pressure Regulator /

Combustion Chamber Compensation

6) Pressure Regulator for Minimum and

Maximum Outlet Pressure

7) Gas Outlet Pressure Electric Modulator

8) Pilot Outlet

9) Main Gas Outlet

10) Side Outlet

11) Main Gas Inlet

Regency® PG36-5 Gas Log Fireplace

INSTALLATION

Conversion From NG To LPG Kit #513-968

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION!!

1) Shut off the gas supply and unplug the

power cord.

2) Carefully remove the glass, logs and

lava rock.

3) Remove burner.

4) Remove burner oriﬁ ce with a 1/2"

wrench and discard. Use a wrench to

hold on to the elbow behind the oriﬁ ce.

5) Reinstall new burner oriﬁ ce stamped #52

and tighten.

6) Pull out the pilot hood by hand.

9) Adjust the burner aeration setting to and

re-install the burner.

10) Open the bottom louver.

8) Put in the new LPG oriﬁ ce with the allen

key. Then put back the pilot hood.

Burner Oriﬁ ce

Pilot

Hood

Pilot

Hood

removed

7) Remove the pilot oriﬁ ce with the allen

key.

LPG Conversion Kit Contains:

Qty. Part # Description

1 904-390 Burner Oriﬁ ce #52

1 904-529 5/32" Allen Key

1 918-590 Label "Converted to LP"

1 908-528 Red "LPG" label

1 910-037 #30 ULPG Pilot Oriﬁ ce

1 918-577 Instruction Sheet

11) Remove the front cover by undoing the 2

screws.

Front Cover

12) Stick the conversion label "This unit has

been converted to LPG" over top of the

serial number decal.

13) Replace the yellow "NG" label with the

red "LPG" label.

14) Carefully pull out the control box from

underneath the ﬁ rebox.

Note: The control box is held in place with

velcro.

Pilot

Oriﬁ ce

Page is loading ...

Regency PG36LPG5-R Owner's Installation Manual

Brand: Regency

Model: PG36LPG5-R

Category: Fireplaces

Type: Owner's Installation Manual

This manual is also suitable for

Download PDF

report

Regency PG36LPG5-R Owner's Installation Manual

This manual is also suitable for

Regency PG36LPG5-R Owner's Installation Manual

Related papers

Other documents