Regency Fireplace Products GFI300LULPG-R Owners & Installation Manual

Brand: Regency Fireplace Products

Model: GFI300LULPG-R

Category: Fireplaces

Type: Owners & Installation Manual

Models: GFI300LNG-R

GFI300LLP-R

GFI300LULPG-R

Owners &

Installation

Manual

04/15/14

LISTINGS AND CODE APPROVALS

These gas appliances have been tested in

accordance with AS4553, NZS 5262 and

have been certiﬁ ed by the Australian Gas

Association for installation and operation as

described in these Installation and Operating

Instructions.

Your unit should be serviced annually by

an authorised service person.

919-293

GFI300L Gas Inbuilt

FOR YOUR SAFETY

What to do if you smell gas:

Do not try to light any appli-

ance

Do not touch any electrical

switch: do not use any phone

in your building.

Immediately call your gas

supplier from a neighbour's

phone. Follow the gas sup-

plier's instructions.

If you cannot reach your gas

supplier, call the ﬁ re depart-

ment.

WARNING:

Improper installation, adjustment, alteration,

service or maintenance can cause injury or

property damage. Refer to this manual. For

assistance or additional information consult

an authorised installer, service agency or

the gas supplier.

FOR YOUR SAFETY

Do not store or use gasoline or other ﬂ am-

mable vapours and liquids in the vicinity of

this or any other appliance.

Installation and service must be performed

by an authorised installer, service agency or

the gas supplier.

PLEASE KEEP THESE INSTRUCTIONS

FOR FUTURE REFERENCE

REGENCY

GAS FIREPLACE INBUILT FIREPLACE

TO THE NEW OWNER

Congratulations! You are the owner of a state-of-the-art Gas Inbuilt Fireplace by Regency

Industries. The Regency Gas Fireplace Series of hand crafted appliances has been designed

to provide you with all the warmth and charm of a ﬁ replace, at the ﬂ ick of a switch. The model

GFI300L of this series has been approved by Australian Gas Association for both safety and

efﬁ ciency. As it also bears our own mark, it promises to provide you with economy, comfort

and security for many trouble free years to follow. Please take a moment now to acquaint

yourself with these instructions and the many features of your Regency Fireplace.

Regency GFI300L Gas Fireplace Inbuilt 33

TABLE OF CONTENTS

Copy of Data Label ........................................................4

Unit Dimensions ............................................................5

Installation

For your safety...............................................................6

Gas pipe testing.............................................................6

Before you start .............................................................6

Checklist ........................................................................6

Minimum ﬁ replace dimensions ......................................7

Masonry Installation: ..............................................7

Mantel Leg Clearances..................................................8

Minimum Clearances to Combustibles ..........................8

Mock Fireplace dimensions ...........................................9

Optional mock ﬁ replace Installation .............................10

Standoff Assembly ...............................................10

Framing & Finishing.....................................................11

Appliance Gas connection ..........................................12

Draft diverter Connection.............................................13

Gas connection ...........................................................13

Flueing ......................................................................... 13

Test For Flue Spillage ..................................................13

Gas Line Installation ....................................................14

Pilot Adjustment ...........................................................14

Gas Pipe Pressure Testing ..........................................14

845 S.I.T. Valve Description .........................................14

Aeration Adjustment ....................................................14

Conversion Kit to LP or ULPG .....................................15

Optional Enamel panels ..............................................17

Log Set installation ......................................................18

Glass door installation .................................................20

Faceplate & trim installation ........................................21

Primary Glass guard installation ..................................22

Optional mesh guard installation .................................22

Wiring ..........................................................................23

Operating Instructions

Operating Instructions ................................................24

Lighting Instructions.....................................................24

Shutdown Instructions .................................................24

First Fire ......................................................................24

Remote Control ..........................................................24

Summary Of Controls .................................................24

Fan Operation..............................................................24

Copy of Lighting Plate Instructions ..............................25

Normal Operating Sounds Of .....................................25

Gas Appliances............................................................25

Resetting the unit.........................................................25

Maintenance

Maintenance Instructions.............................................26

General Vent Maintenance ..........................................26

Glass Gasket ...............................................................26

Glass Door...................................................................26

Glass Replacement .............................................26

Valve Tray replacement ...............................................27

Fan maintenance .........................................................28

Pressure switch replacement ......................................28

Parts

Main Assembly ............................................................30

Faceplate Assembly ....................................................32

Burner and pilot Assembly ...........................................32

Warranty

Warranty ......................................................................35

4Regency GFI300L Gas Fireplace Inbuilt

INSTALLATION

(Australia Only)

This is a copy of the label that accompanies

each Regency GFI300L Gas Inbuilt ﬁ replace.

We have printed a copy of the contents here

for your review.

DATA BADGE NOTE: Regency units are constantly

being improved. Check the label on the unit and

if there is a difference, the label on the unit is the

correct one.

DO NO T

OPERATE THIS APPLIANCE BEFORE READING THE

INSTRUCTIONS BOOKLET.

PLACE ARTICLES ON OR AGAINST THIS APPLIANCE

STORE CHEMICALS OR FLAMMABLE MATERIALS

SPRAY AEROSOLS IN THE VICINITY OF THIS

APPLIANCE WHILE IN OPERATION.

OPERATE WITH PANELS, COVERS OR GUARDS

REMOVED FROM THIS APPLIANCE.

ENCLOSE THIS APPLIANCE.

MODIFY THIS APPLIANCE.

NEAR THIS APPLIANCE.

DO NO T

908-602a

Regency GFI300L Gas Fireplace Inbuilt 5

INSTALLATION

UNIT DIMENSIONS

236mm

362mm

584mm

288 mm

38mm

908mm

682mm

683 mm

362 mm

100 mm

flue

6Regency GFI300L Gas Fireplace Inbuilt

INSTALLATION

IMPORTANT:

SAVE THESE

INSTRUCTIONS

The Regency Gas Fireplace must be installed in

accordance with these instructions. Carefully read

all the instructions in this manual ﬁ rst.

NOTE: FAILURE TO FOLLOW THESE INSTRUC-

TIONS COULD CAUSE A MALFUNC-

TION OF THE HEATER WHICH COULD

RESULT IN DEATH, SERIOUS BODILY

INJURY, AND/OR PROPERTY DAMAGE.

FAILURE TO FOLLOW THESE INSTRUC-

TIONS MAY ALSO VOID YOUR FIRE

INSURANCE AND/OR WARRANTY.

FOR YOUR SAFETY

This appliance requires air for proper combus-

tion. Always provide adequate combustion and

ventilation air. Follow instructions and information

in the current AS5601-2013, NZS 5261 or local

codes. Consult the "authority having jurisdiction"

to determine the need for a permit prior to starting

the installation.

GAS PIPE TESTING

The appliance must be isolated from the gas

supply piping system by closing its individual

manual shutoff valve during any pressure testing

of the gas supply piping system at test pressures

equal to or less than 3.45 kPa.

Speciﬁ cations:

Fuel: NG, Propane, or ULPG

Electrical: 240 volt 50 hz system

Fan/Blower: 3-speed

Log Sets: Ceramic ﬁ bre

BEFORE YOU START

Installation is to be carried out ONLY by an

authorised person.

1) The appliance shall be installed in accord-

ance with the manufacturer's installation

instructions,local gas ﬁ tting regulations,

municipal building codes, water supply

regulations,electrical wiring regulations, with

AS5601-2013.(AGA gas installation code)

NZS 5261(New Zealand)

2) Installation and repair should be done ONLY

by an authorised person.

3) The appliance should be inspected before

use and at least annually by an authorised

service person. More frequent cleaning may

be required due to excessive lint from carpet-

ing, bedding material, etc. It is imperative that

control compartments, burners and circulating

air passageways of the appliance be kept clean

and free from excessive lint from carpeting.

4) See general construction and assembly instruc-

tions. This appliance may only be installed in a

ﬂ ued, non-combustible ﬁ replace. The appliance

and ﬂ ue should be enclosed when installed or

passing through a living area, where children

may come in contact with it.

5) Always connect this space heater to a chimney

and ﬂ ue to the outside of the building envelope.

Never ﬂ ue to another room. Make sure that the

ﬂ ue is properly sized and is of adequate height

to provide the proper draft.

6) Inspect the ﬂ ueing system annually for blockage

and any signs of deterioration.

7) Any safety glass removed for servicing must

be replaced prior to operating the appliance.

8) To prevent injury, do not allow anyone who is

unfamiliar with the operation to use the ﬁ replace.

9) Assemble and install the faceplate and trim.

10) Install the glass front.

11) Install bottom louvres and ﬂ ush front.

12) Install Optional Remote Control.

13) Final check: Before leaving this unit with the

customer, the installer must ensure that the

appliance is ﬁ ring correctly. This includes:

a) Clocking the appliance to ensure the correct

ﬁ ring rate.

b) Adjusting the primary air, if required, to en-

sure that the ﬂ ame does not carbon. See

page 7.

c) Ensuring that the appliance is ﬂ ueing cor-

rectly. See page 7.

INSTALLATION

CHECKLIST

The Regency Gas Insert is installed as listed below.

1) Unit Location - check Clearances to Combus-

tibles.

2) Make the gas connections.

3) Install the ﬂ ue or liner to the sliding draft diverter.

4) Install Flueing. Slide the unit into the ﬁ replace.

Attach draft diverter to the insert.

5) Test gas pressure. Check aeration.

6) Test for ﬂ ue spillage.

7) Install the optional panels.

8) Install the log set.

WARNING: This ﬁ replace has been converted

for use with a gas ﬁ replace insert only and

cannot be used for burning wood or solid fuels

unless all original parts have been replaced,

and the ﬁ replace re-approved by the authority

having jurisdiction.”.

Regency GFI300L Gas Fireplace Inbuilt 7

INSTALLATION

MINIMUM FIREPLACE DIMENSIONS

The below minimum cavity requirements are to be maintained to ensure safe

and proper operation of the appliance. Ensure all construction conforms to

local building codes.

MASONRY INSTALLATION:

The minimum ﬁ replace dimensions for a masonry installation are shown in

the diagrams below.

367mm

590mm

688mm

367mm

238mm125mm

8Regency GFI300L Gas Fireplace Inbuilt

INSTALLATION

12" 6"

(152mm)

12" (305mm)

21-1/4"

(540mm)

10"

(254mm)

26"

(660mm)

To p o f

Fireplace

Opening

20"

(508mm)

(305mm)

13"

(330mm)

(25mm)

Top of Faceplate

MINIMUM

CLEARANCES TO

COMBUSTIBLES

The minimum ﬁ replace clearances for the Regency gas space heater are

shown in the following diagrams:

From Unit

Sides A 464 mm

Ceiling B 860 mm

Mantle C see Mantel Clearances

Min. Alcove Width E 1924 mm

Max. Alcove Depth F 914 mm

(102mm)

Allowable mantel

leg projection

7-1/8” (181mm)

10”(203mm)

13 ”(279mm)

1.5" (38mm)

MANTEL LEG

7”(178mm)

MANTEL LEG CLEARANCES

Combustible mantel leg clearances as per diagram:

Regency GFI300L Gas Fireplace Inbuilt 9

INSTALLATION

Framing

Dimensions Description GFI300L

A Framing Height 25-5/8” (650mm)

B Framing Width 31-1/2" (800mm)

C*Framing Depth 16-1/2" (420mm)

E Corner Wall Depth 39-9/16" (1006mm)

F Corner Facing Wall Width 56" (1422mm)

I Gas Connection Opening Height 2" (51mm)

J Gas Connection Height 2-5/8" (67mm)

K Gas Connection Inset 3-11/16" (99mm)

L Gas Connection Opening Width 2-1/2" (64mm)

Timber

Studs

Finished Floor

Note: All framing may

be of wood construction.

OPTIONAL MOCK FIREPLACE (ZERO CLEARANCE) DIMENSIONS

(NO MASONRY CHIMNEY)

10 Regency GFI300L Gas Fireplace Inbuilt

INSTALLATION

OPTIONAL MOCK FIREPLACE (ZERO CLEARANCE) INSTALLATION

Diagram 1

Diagram 2

Diagram 3

Diagram 4

STANDOFF ASSEMBLY

The top, side, rear and bottom standoffs are shipped in a ﬂ at position and

must be folded into shape and attached - see Diagram 1.

1. Remove the standoffs from the mock ﬁ replace packaging.

2. Take each standoff and bend into the correct shape. Bend up at the bend

lines until the screw holes in the standoff and the pre-punched screw holes

on the unit line up.

3. Install left and right nailing brackets. Remove existing screws from the

outside of the unit - line up bracket with holes in the unit and secure with

2 removed screws.

See framing clearance dimensions in the installation manual.

Mock Fireplace (zero clearance) Kit Contents

3 Standoffs

2 Side brackets

Note: Side brackets can be adjusted between 13 mm to 38 mm. This

adjustment must be done before unit is moved into framed opening.

Regency GFI300L Gas Fireplace Inbuilt 11

INSTALLATION

FRAMING & FINISHING

1) Frame in the enclosure for the unit with framing material.

Note: When constructing the framed opening, please ensure there

is access to install the gas lines when the unit is installed.

2) The unit does not have to be completely enclosed in a chase. You

must maintain clearances from the vent to combustible materials: See

"Clearances" section. Combustible materials can be laid against the

side and back standoffs and the stove base.

3) Finishing material may be brought to the side and top of the framing.

do not bring combustible material beyond the framed opening. This is

both for safety and servicing of the appliance.

Unit shown with Fascia

800mm

650mm

Finished Wall

Framed Opening

12 Regency GFI300L Gas Fireplace Inbuilt

INSTALLATION

GAS CONNECTION

3) Locate the center point where the ﬂ ue will pass through the chimney above

the appliance. Move the appliance into the exact location where it is to be

installed. Ensure that the Insert is level.

4) The installer must provide a valve with a plugged tapping, accessible for

test gauge connection, immediately upstream of the gas supply connection

to the appliance.

CAUTION: If the glass is removed or opened for servicing, it must be

replaced and closed prior to operating the appliance. The glass must be

ﬁ xed in the door when operating.

SPECIFICATIONS

NG LP ULPG

Injector

Size

#40 #53 #55

Input

Rating

Max. 30

Max. 27

Max. 21

Min.

20mj

Min. 22

Min. 17

Manifold

Pressure

0.9 kPa 2.3 kPa 2.3 kPa

Aeration

Setting

5 mm 13 mm full

open

GAS CONNECTION WARNING:

Only persons licensed to work with gas piping

may make the necessary gas connections to

this appliance.

1) If the appliance is to be installed into an existing chimney system, thoroughly

clean the masonry or factory built ﬁ replace.

2) The gas connection is 1/2" BSP.

Regency GFI300L Gas Fireplace Inbuilt 13

INSTALLATION

Diagram 1

Diagram 2

GAS CONNECTION

GAS CONNECTION WARNING:

Only persons licensed to work with gas

piping may make the necessary gas con-

nections to this appliance.

1) If the appliance is to be installed into an exist-

ing chimney system, thoroughly clean the

masonry or factory built ﬁ replace.

2) The gas connection is 1/2" BSP.

3) Locate the center point where the ﬂ ue will pass

through the chimney above the appliance. Move

the appliance into the exact location where it is

to be installed. Ensure that the Insert is level.

4) The installer must provide a valve with a plugged

tapping, accessible for test gauge connection,

immediately upstream of the gas supply con-

nection to the appliance.

CAUTION: If the glass is removed or opened for

servicing, it must be replaced and closed prior

to operating the appliance. The glass must be

ﬁ xed in the door when operating.

FLUEING

THE APPLIANCE MUST NOT BE CONNECTED

TO A CHIMNEY FLUE SERVING A SEPARATE

SOLID FUEL BURNING APPLIANCE.

This appliance is designed to attach to a 100

mm diameter twin skin or listed gas fuel type

ﬂ ue liner running the full length of the chimney.

A minimum ﬂ ue height of 0.6 m. is required for

masonry applications. The Regency Inbuilt Fireplace

incorporates its own internal draft diverter, so no

additional external draft diverter is required.

Periodically check that the ﬂ ue is unrestricted and

an adequate draft is present when the unit is in

operation. (See page 7 for spillage test.)

Before installing ﬂ ue system ensure that the damper

plate is open and secure to prevent the damper plate

from falling down and crushing the liner.

Install to AS5601-2013,(Australia) NZS 5261 (New

Zealand).

Combustion and Ventilation Air

WARNING: This appliance needs fresh

air for safe operation and must be

installed with provisions for adequate

combustion and ventilation air avail-

able to the room in which it is to be

operating.

Air for combustion is drawn in through the front of

the unit, therefore, the front of the unit must be kept

DRAFT DIVERTER

CONNECTION

1) Attach the ﬂ ue to the ﬂ ue collar on the detach-

able draft diverter. The ﬂ ue collar of the appli-

ance will ﬁ t inside a standard ﬂ ue and may be

fastened directly to the ﬂ ue by sheet metal

screw. Diagram 1.

2) Before pushing the appliance into position inside

the ﬁ replace, align the draft diverter with the

guides on the insert top and push forward. While

pushing the unit back into place keep pulling the

draft diverter forward until the screw hole in the

spill tube aligns with the screw hole in the top

of the ﬁ rebox. The screw is secured through the

inside top of the ﬁ rebox into the bottom of the

spill tube. (If screw holes do not line up then

draft diverter is not positioned correctly.)

Diagram 2.

NOTE: Final gas connection should be after unit

is in place to avoid damage to line when

pushing the unit into position.

TEST FOR FLUE

SPILLAGE

A " spillage" test must be made before the

installed unit is left with the customer. Follow

the procedure below:

1) Start all exhaust fans in the home and then

close all external doors and windows in the

house.

2) Light the unit and set controls to maximum.

Turn fan off.

3) After ﬁ ve minutes, test that there is a “pull”

on the ﬂ ue by placing a smoke match, or

similar device which gives off smoke, in both

sides of the unit. See diagram 1.

Flue spillage

test location area

normal draft

downdraft

or block flue

Diagram 1

For wind turbulent sites, a wind cap may remedy

the problem. These caps are not included with the

standard ﬂ ue kit and will need to be purchased

separately.

The smoke should be drawn into the unit. If the

smoke is still not drawn into the spill tube, turn the

unit off and check for the cause of the lack of draft.

If necessary, rectify.

14 Regency GFI300L Gas Fireplace Inbuilt

INSTALLATION

AERATION ADJUSTMENT

The burner aeration is factory set but may need

adjusting due to either the local gas supply or

altitude. Open the air shutter for a blue ﬂ ame or

close for a more yellow ﬂ ame.

Minimum Air Shutter Opening:

NG 3/16" (5mm)

LPG 1/2" (13mm)

ULPG Full Open

Note: Any damage due to carboning resulting

from improperly setting the aeration

controls is NOT covered under warranty.

GAS PIPE PRESSURE

TESTING

The appliance must be isolated from the gas sup-

ply piping system by closing its individual manual

shut-off valve during any pressure testing of the

gas supply piping system at test pressures equal

to or less than 1/2 psig. (3.45 kPa). Disconnect

piping from valve at pressures over 1/2 psig.

The manifold pressure is controlled by a regulator

built into the gas control, and should be checked

at the pressure test point.

Note: To properly check gas pressure, both

inlet and manifold pressures should be

checked using the valve pressure ports

on the valve.

1) Make sure the unit is in the "OFF" position.

2) Loosen the "IN" and/or "OUT" pressure tap(s),

turning counterclockwise with a

1/8" wide ﬂ at screwdriver.

3) Attach manometer to "IN" and/or "OUT" pressure

tap(s) using a 5/16" ID hose.

4) Turn the unit on with the remote or wall switch

5) The pressure check should be carried out with

the unit burning and the setting should be within

the limits speciﬁ ed on the safety label.

6) When ﬁ nished reading manometer, turn off

the unit, disconnect the hose and tighten the

screw (clockwise) with a 1/8" ﬂ at screwdriver.

Note: Screw should be snug, but do not over

tighten.

Note: If you have an incorrect ﬂ ame pattern,

contact your Regency® dealer for further

instructions.

Incorrect ﬂ ame pattern will have small, probably

yellow ﬂ ames, not coming into proper contact

with the rear burner or ﬂ ame sensor.

Burner

Flame Sensor

Pilot Ignitor

PILOT ADJUSTMENT

Periodically check the pilot ﬂ ames. Correct ﬂ ame

pattern has three strong blue ﬂ ames: 1 ﬂ owing

around the ﬂ ame sensor and 1 ﬂ owing across

the burner (it does not have to be touching the

burner), and 1 opposite the ﬂ ame sensor.

845 S.I.T. VALVE

DESCRIPTION

1) On-Off Solenoid Valve EV1

2) On-Off Solenoid Valve EV2

3) Inlet Pressure Test Point

4) Outlet Pressure Test Point

5) Connection for Pressure Regulator/Combustion

Chamber Compensation

6) Pressure Regulator for Minimum and Maximum

Outlet Pressure

7) Gas Outlet Pressure Electric Modulator

8) Pilot Outlet

9) Main Gas Outlet

HIGH ELEVATION

This unit is approved for altitude 0 to 1372m.

GAS LINE

INSTALLATION

Since some municipalities have additional local

codes it is always best to consult with your local

authorities.

When using copper or ﬂ ex connectors use only

approved ﬁ ttings. Always provide a union so

that gas lines can be easily disconnected for

servicing. Flare nuts for copper lines and ﬂ ex

connectors are usually considered to meet this

requirement.

NOTE: A shutoff / dante valve should be

supplied in or near the unit (or as per local

codes) for ease of servicing this appliance.

Regency GFI300L Gas Fireplace Inbuilt 15

INSTALLATION

Conversion Kit from NG to LP or ULPG

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !!

1. Unplug or disconnect the power source to the unit.

2. Shut off the gas supply and remove the gas connection from the valve.

3. Remove the faceplate, door frame, safety glass or screen.

4. Remove the glass door. (See door removal section in this manual).

5. Remove the logs. (See log section in this manual).

6. Remove the panels. (See panel section in this manual).

7. Remove the log tray, by removing 2 screws in locations shown below.

8. Lift log tray up and out to remove.

9. Remove burner - loosen screw on left side, remove screw from right side

- slide to the right and lift up and out to remove and discard

Loosen Remove

10. Remove 2 screws in location shown below to remove front bracket.

11. Remove pilot retainer clip with pliers and pull off the pilot cap to expose

the pilot oriﬁ ce.

Pilot retainer clip

12.

Remove burner oriﬁ ce with a 1/2" wrench and discard. Use another wrench

to hold on to the elbow below the oriﬁ ce.

16 Regency GFI300L Gas Fireplace Inbuilt

INSTALLATION

13. Reinstall new burner oriﬁ ce LPG stamped #53 or ULPG burner oriﬁ ce

stamped #55 and tighten.

14. Install new LP burner supplied with kit ensuring aeration is set to 13mm

for LPG or fully open for ULPG - prior to install.

15. Replace the yellow "NG" label with the red "ULPG" label.

16. Carefully pull out the control box.

NOTE: The control box is held in place with velcro.

17. Remove the heat shield from the control box by removing the 2 screws.

18. Remove the control box cover by undoing the 3 screws.

Manoeuvre through antenna.

20. Reverse Steps 18,17,16,14,8,7,6, and 5.

21. Turn on gas supply and plug in power cord.

22. Adjusting the Outlet Pressure

All the adjustments must be carried out in the following order:

Control Box

Cover

Antenna

Jumper Location

19. Remove the jumper using pliers and discard.

Jumper

After carrying out all adjustments, block the setting screws with

paint, taking care not to obstruct the breather oriﬁ ce of the pres-

sure.

Put back the modulator plastic cap.

WARNING: To ensure the correct operation of the modulator it is

necessary that the plastic cap (A) is returned to its original loca-

tion.

23. Reverse Steps 10,4,3,2 and 1.

24. At the end of all setting and adjustment operations, check electrical

installation and gas leaks.

24. Check operation of ﬂ ame control.

25. Check for proper ﬂ ame appearance and glow on logs.

Cable

Electric

Modulator

Remove the modulator plastic cap (A) using needle nose pliers.

Maximum pressure: Turn the unit ON to its highest input rating. Screw

in the nut (B) to increase the outlet pressure and screw it out to decrease

it. Use a 10 mm wrench.

NOTE: The outlet pressure must be set to maximum 2.3 kPa.

Minimum pressure: Remove one of the cables connected to the electric

modulator. While holding the nut (B) with a wrench, screw in the screw (C)

to increase the pressure and screw it out to decrease it. Use a screwdriver

6 x 1 blade.

NOTE: The outlet pressure must be set to minimum 1.5 kPa.

Installer Notice:

These instructions must be left

with the appliance.

Regency GFI300L Gas Fireplace Inbuilt 17

INSTALLATION

OPTIONAL ENAMEL PANELS

1) Unwrap the panels from the protective wrapping.

2) Remove the glass front if already installed (see manual).

3) Put the rear panel ﬂ at against the back of the unit.

4) Before installing the side panels, loosen the screws for the tabs enough

so that you can slide the tabs on to the screws easily but that the tabs are

secure. For the location of the side tab screws see diagram 2.

5) Slide the side panels into position and tighten the screw to secure the

tab - repeat to install panel on opposite side of unit.

6) Reinstall glass door (see manual).

18 Regency GFI300L Gas Fireplace Inbuilt

Read the instructions below carefully and refer to the images. If the logs are broken do not use the unit until they are replaced. Broken logs ca

interfere with pilot operation.

Improper positioning of the logs may create carbon build-up and can alter the unit's performance which is not covered under warranty.

*For Touch Ups: Satin Black paint is included.

. Line up pin holes on the bottom of Log 1 with pins behind burner as

shown below. 2

2. Locate pin hole on Log 2 and line up with pin on the right side of the

burner. The left end of Log 2 will rest against a tab in location shown

below.

3. Place Log 3 on the centre of the burner, rest the log against the centre

tabs.

Logs 1 - ﬁ ts over pins behind

burner

Logs 2 - ﬁ ts over pin on left side

- rests against tab on right

Logs 2 in position

Logs 3 - place in centre of

burner, resting against tabs

Logs 1 - in position

1 Rear Log

2 Right Log

3 Centre Log

4 Left Log

5 Right Upright Cross Log

6 Left Upright Cross Log

7 Left Front Log Piece

8 Centre Front Log Piece

9 Centre Right Log Piece

INSTALLATION

LOG SET INSTALLATION

Regency GFI300L Gas Fireplace Inbuilt 19

5 mm

In position, the bark pattern on Log 3 should line up with the pattern on

Log 2. It should appear as if one log has split during burning.

4. Place Log 4 on the burner, rest the back of Log 4 on the tab located on

the left side of the burner.

IMPORTANT: A 5 mm gap must be maintained between Logs 3 and 4 to

ensure proper burner function.

5. Place Log 5 across Logs 1 and 2. The left side of the "Y" in Log 5 ﬁ ts into

the notch in Log 1. The other end of the Log 5 will rest on the burner tray,

covering the hole as shown below.

6. Place Log 6 across Logs 1 and 4. The top part of Log 6 ﬁ ts into the notch

on the left hand side of Log 1. The bottom end of Log 6 should sit so it

covers a screw on the burner tray.

7. Place Log 7 on the left hand side of the burner, Log 7 will sit in a notch on

Log 6 and the bottom of Log 7 will rest on a tab located on the burner.

Log 6 ﬁ ts in notch on Log 1

Log 7 ﬁ ts in notch on Log 6

Log 7 in position

Logs 2 & 3 - continuous bark line

Log 4 rests against tab on burner

5 mm gap between Logs 3 & 4

Log 5 covers hole on burner

tray trim

INSTALLATION

20 Regency GFI300L Gas Fireplace Inbuilt

. Log 8 will cover pilot assembly, resting on pilot assembly bracket and trim

of the burner tray as shown below.

Log 8 covers Pilot Assembly

Log 7 in position

. Rest Log 9 upright against Log 2 as shown below

Final Install

Log 9 rests on Log 2

INSTALLATION

GLASS DOOR INSTALLATION

1. Lift glass door and slot keyhole in glass door over screw installed in unit

body.

2. Once in position, slide glass door down and secure with 2 screws at the

bottom of the door as shown below, and tighten the top 2 (two) screws.

3. To remove- reverse steps.

Page is loading ...

Regency Fireplace Products GFI300LULPG-R Owners & Installation Manual

Brand: Regency Fireplace Products

Model: GFI300LULPG-R

Category: Fireplaces

Type: Owners & Installation Manual

Download PDF

report

Regency Fireplace Products GFI300LULPG-R Owners & Installation Manual

Regency Fireplace Products GFI300LULPG-R Owners & Installation Manual

Related papers

Other documents