WebGate i-Rec B104 Installation guide

i-Rec B104

Installation Guide

(v 1.4)

2 2003. 06. 30 (v 1.4) WEBGATE Inc.

FCC Compliance Statement

Caution: Any changes or modifications in construction of this device which are not expressly

approved by the party responsible for compliance could void the user's authority to operate the

equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment

generate, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

Dispose of used batteries properly with regards to environmental considerations.

WEBGATE Inc. 2003. 06. 30 (v 1.4) 3

Important Notice

1. When i-Rec B104 is in operation, do not place heavy monitors or other items on top of unit.

Do not vertically stack more than four i-Rec B104s.

2. i-Rec B104 is not weatherproof. Therefore consider environmental specifications that are

included in the manual. In case of outdoor use, equip weatherproof case to protect i-Rec

B104 from water, moisture, or severe temperature variations (higher or lower than

specifications). Clean i-Rec B104 by gently wiping outside shell with a clean, dry cloth.

3. Be sure to use the DC adapter that is provided with the unit. Connecting i-Rec B104 directly

to an AC current may cause electrical damage to i-Rec B104.

4. Be cautious of handling i-Rec B104. Physical shocks may harm the product.

5. i-Rec B104 is made with a metal case. When installing the camera, be sure it is attached

securely to avoid any injuries. Be careful to locate the camera where children cannot reach

it.

6. If i-Rec B104 does not operate properly, please contact your WebGate distributor for after

sales service. In all cases, you are prohibited to disassemble the product. If so, WebGate is

not responsible for any malfunction and will void service warranty.

7. Security surveillance laws may differ for each country and from region to region. Therefore,

please contact the local authorities first to avoid any surveillance law violations and use for

authorized purposes only.

i-Rec B104 Contents

4 2003. 06. 30 (v 1.4) WEBGATE Inc.

Contents

Introduction............................................................................................................................... 6

1. Key Features.................................................................................................................... 6

2. Supplied Accessories ....................................................................................................... 7

3. Product Views and Description ........................................................................................ 9

Installing & Connecting.......................................................................................................... 10

4. Installing i-Rec B104 ...................................................................................................... 10

4.1. Connecting cameras to i-Rec B104......................................................................... 10

4.2. Connecting i-Rec B104 to Network ..........................................................................11

4.2.1. Connecting i-Rec B104 to PC directly ...............................................................11

4.2.2. Connecting i-Rec B104 to Local Network......................................................... 12

5. Setting i-Rec B104 & Getting an Image.......................................................................... 13

5.1. Installing CamViewer II .......................................................................................... 13

5.1.1. Installation of Software..................................................................................... 13

5.1.2. Uninstalling ...................................................................................................... 14

5.2. Connecting to i-Rec B104 ....................................................................................... 15

5.3. Setting IP address................................................................................................... 16

5.4. Setting Camera Input Channel ................................................................................ 17

5.5 Checking Images of i-Rec B104.............................................................................. 18

6. Installing HDD ................................................................................................................ 20

6.1. Usable HDD ............................................................................................................ 20

6.2. HDD Installation Procedure..................................................................................... 20

7. Recording & Playback.................................................................................................... 24

7.1 Setting HDD............................................................................................................ 24

7.2. Setting Time................................................................................................................ 25

7.3. Setting Recording Schedule ....................................................................................... 26

7.4. Playback..................................................................................................................... 28

8. Input / Output ................................................................................................................. 30

8.1. Connecting Serial Port................................................................................................ 31

8.1.1. Specifications of Serial Port ............................................................................. 31

8.1.2. Serial Port View ............................................................................................... 31

8.1.3. Connecting & setting RS-232 port.................................................................... 31

8.1.4. Connecting & setting RS-485 port.................................................................... 32

8.1.5. Connecting & setting RS-422 port.................................................................... 33

Contents i-Rec B104

WEBGATE Inc. 2003. 06. 30 (v 1.4) 5

8.2. Connecting Alarm Output ........................................................................................ 35

8.2.1. Specifications of Alarm Output ......................................................................... 35

8.2.2. Alarm output port view ..................................................................................... 35

8.2.3. Connecting & Setting ....................................................................................... 35

8.3. Connecting Sensor Input......................................................................................... 37

8.3.1. Specifications of Sensor Input.......................................................................... 37

8.3.2. Sensor Input Port View .................................................................................... 37

8.3.3. Connecting & Setting ....................................................................................... 37

8.3.4. Connecting sensors for 1.0 or below main version PCB of i-Rec B104............ 38

8.4. Connecting Impedance Setup Switch for Video Input ............................................. 39

8.5. Video Input.............................................................................................................. 39

APPENDIX .............................................................................................................................. 40

#1. Frequently Asked Question (FAQ) .............................................................................. 41

#1.1. About i-Rec B104’s Feature................................................................................. 41

#1.2. About i-Rec B104 Installing ................................................................................. 43

#2. Utilizing IP Addresses on Local Network..................................................................... 46

#2.1. Introduction.......................................................................................................... 46

#2.2. IP Construction and Network class...................................................................... 46

#2.3. C-class Network .................................................................................................. 47

#3. Setting the fixed IP address on PC............................................................................. 50

#4. CRS Help ................................................................................................................... 52

#4.1. When using ADSL ............................................................................................... 52

#4.2. When resetting local network from ADSL ............................................................ 55

#4.3. When using Cable modem .................................................................................. 58

#5. Upgrading i-Rec B104 Firmware ................................................................................ 59

#5.1. Connecting i-Rec B104 to PC.............................................................................. 59

#5.2. Upgrade firmware with upgrading program.......................................................... 59

#6. Using CD-ROM........................................................................................................... 61

#7. Specifications ............................................................................................................. 62

i-Rec B104 Introduction

6 2003. 06. 30 (v 1.4) WEBGATE Inc.

Introduction

1. Key Features

i-Rec B104 is a 4-channel box style Network DVR. It is an all-in-one system with a Web server

of embedded Linux, a networking device, and a HDD (Removable). i-Rec B104 only needs

designated power supply and network connection in order to operate.

 Monitoring through Network

 RS 232 / RS 485 / RS422 port support for PTZ control

 Embedded Linux OS for excellent stability and less downtime

 Wavelet compression (30%~300% greater efficiency than JPEG) for higher refresh rate and

crisper images

 4 channels video input support

 4 alarms output support

 S/W motion detection

 Dynamic IP (DHCP, Floating IP) support (xDSL and Cable modem)

Introduction i-Rec B104

WEBGATE Inc. 2003. 06. 30 (v 1.4) 7

2. Supplied Accessories

Unpack and check all items.

1. i-Rec B104 (1)

2. DC POWER SUPPLY (1)

(110V ~ 220V)

3. AC POWER CORD (1)

4. CD-ROM (INCLUDING CAMVIEWER

AND OPERATING INSTRUCTIONS) (1)

5. ETHERNET CABLE (1, RED)

(UTP CATEGORY 5 CROSS CABLE)

6. ETHERNET CABLE (1, IVORY)

(UTP CATEGORY 5 DIRECT CABLE)

i-Rec B104 Introduction

8 2003. 06. 30 (v 1.4) WEBGATE Inc.

7. INSTALLATION GUIDE (1)

8. TERMINAL BLOCK (3)

(8PIN x 2, 7PIN x 1)

9. HDD MOBILE RACK KEY (1)

10. SCREW (4)

Introduction i-Rec B104

WEBGATE Inc. 2003. 06. 30 (v 1.4) 9

3. Product Views and Description

(1) HDD mobile rack

(2) Alarm output

(3) Sensor input

(4) Serial port

(5) Video input

(6) Impedance control switch

(7) Ethernet

(8) DC power

i-Rec B104 Installing & Connecting

10 2003. 06. 30 (v 1.4) WEBGATE Inc.

Installing & Connecting

4. Installing i-Rec B104

This user’s guide describes the most two common network conditions for installing B-104:

(1) i-Rec B104 and administrator’s PC uses fixed or private IP address.

(2) Computers and B104 are connected directly or to local network.

4.1. Connecting cameras to i-Rec B104

(1) Connect i-Rec B104 to camera(s) with BNC Cable.

(2) Set impedance control switch of the connected channel. Set impedance by moving switch

<Note>

For more exact settings, please refer to “Impedance setup switch for video Input” of “Input /

Output” in User’s Guide.

Installing & Connecting i-Rec B104

WEBGATE Inc. 2003. 06. 30 (v 1.4) 11

4.2. Connecting i-Rec B104 to Network

Connect i-Rec B104 to client’s PC directly with crossover cable or through HUB with direct cable.

Please refer to the following figures.

4.2.1. Connecting i-Rec B104 to PC directly

(1) Connect i-Rec B104 to client’s PC with crossover cable (Red Ethernet cable).

(2) After supplying power to AC adapter, connect DC12V connector to B104.

(3) If PC is set with dynamic IP, change it into suitable IP address on same network. For more

detailed information, please refer to “Appendix #3 Setting the fixed IP address on PC”.

i-Rec B104 Installing & Connecting

12 2003. 06. 30 (v 1.4) WEBGATE Inc.

4.2.2. Connecting i-Rec B104 to Local Network

(1) Connect B104 to HUB with direct cable (Ivory Ethernet cable).

(2) Connect the supplied AC adaptor to B104.

<Note>

1. To prevent damage to B104, connect power cable only after connecting Ethernet cable.

2. Ethernet cable should be pushed and connected, If not, noise may occur.

3. Check the LED of B104 after supplying power. After power is supplied, yellow LED is on

for the first 5-6 seconds and then goes off. Green LED is on for the first 1-2 seconds, and

then blinks once every second as long as the network is connected.

Installing & Connecting i-Rec B104

WEBGATE Inc. 2003. 06. 30 (v 1.4) 13

5. Setting i-Rec B104 & Getting an Image

The following procedure is for installing i-Rec B104 and checking basic operation. For more

information, please refer to “CamViewer II User Guide”.

5.1. Installing CamViewer II

5.1.1. Installation of Software

(1) Insert Setup CD-ROM into CD-ROM drive of administrator’s PC

(2) Copy the ‘CamViewer II x.x.x Setup.exe’ file onto your PC. Click the file and the CamViewer

II install shield wizard will be installed automatically.

(3) Click the ‘I Agree’ button to accept the license agreement.

(4) Select a component to install and press the ‘Next’ button.

i-Rec B104 Installing & Connecting

14 2003. 06. 30 (v 1.4) WEBGATE Inc.

(5) Browse and choose a directory if the default directory is not preferred. Click the ‘Install’

button, after selecting a directory to install.

(6) Click the ‘Close’ button after CamViewer II Setup Program is installed successfully.

5.1.2. Uninstalling

(1) Click Windows ‘Start’ Button

(2) Select and Click ‘Uninstall’ icon to run Uninstall Shield with mouse

(3) CamViewer II will be deleted automatically.

Installing & Connecting i-Rec B104

WEBGATE Inc. 2003. 06. 30 (v 1.4) 15

5.2. Connecting to i-Rec B104

(1) Click icon on desktop to run “ConfigStation” program

(2) Select B104 folder on the left top of program.

(3) Click the symbol ‘+’ on the left of “Local Area Cameras” to browse all the i-Rec B104s.

(4) Click to select an i-Rec B104 to assign IP Address. The IP address of the selected i-Rec

B104 will appear in the “Change IP” box.

(5) Type new IP address into the “Change IP” and Click “Change IP” button. The default

password of i-Rec B104 is “admin” which can be changed at “User Menu” of Configuration

program.

(6) Click “Login” button to Log-in.

<Note>

Enter ‘User Name’ and ‘Password’. ‘User Name’ is fixed as ‘admin’. If the ‘Save Password’ is

checked, there is no need to enter the Password whenever you were to log in. ‘Save

Password’ function may only be utilized if the Cam is registered on the ‘My Cameras’ directory.

i-Rec B104 Installing & Connecting

16 2003. 06. 30 (v 1.4) WEBGATE Inc.

5.3. Setting IP address

(1) Click “Network” Tab.

(2) Input the assigned values of “IP Address”, “Network Mask”, “Gateway Address” into

“Ethernet” menu.

(3) Click “Apply” button.

<Note>

1. Be careful on typing values into this menu. Without correct network address, nobody will

be able to connect to i-Rec B104.

2. Refer to the User’s guide in setup CD-ROM to install i-RecB104 on Dynamic IP network

environment.

3. If a network firewall is installed, change the port number at “Port Assignment”.

Installing & Connecting i-Rec B104

WEBGATE Inc. 2003. 06. 30 (v 1.4) 17

5.4. Setting Camera Input Channel

(1) Click “Channel” tab.

(2) Select a connected channel on “Channel Enable” menu.

(3) Set Camera Configuration for the selected channel.

- Camera Type: NTSC or PAL

- Camera Color: Color or Black & White

(4) Click “Apply” button.

<Note>

1. If channel is selected but the related camera is not connected, recording and monitoring

performance will decrease.

2. i-Rec B104 can’t be used with both NTSC and PAL cameras connected simultaneously.

i-Rec B104 Installing & Connecting

18 2003. 06. 30 (v 1.4) WEBGATE Inc.

5.5 Checking Images of i-Rec B104

(1) Click the related ICON and run the “Monitor” program.

(2) Click the “Cam Selection” button.

(3) Select “B104” folder.

(4) Select i-Rec B104 to view images.

(5) Click “OK” button.

(6) Select the “Cam connection” button.

Installing & Connecting i-Rec B104

WEBGATE Inc. 2003. 06. 30 (v 1.4) 19

(7) Enter “User Name” and “Password” as “admin” / “admin”.

(8) Click “Login” button to view images of connected channel.

i-Rec B104 Installing & Connecting

20 2003. 06. 30 (v 1.4) WEBGATE Inc.

6. Installing HDD

6.1. Usable HDD

(1) It is recommended to install only Maxtor brand HDD for i-Rec B104.

Manufacturer: MAXTOR

Series Model Name Size Series Model Name Size

6L040J(L)2 40GB 4G120J6 120GB

6L060J(L)3 60GB

DiamondMax

Plus D740X

(7200rpm) 6L080J(L)4 80GB

DiamondMax

D540X

(5400rpm)

(2) To record at maximum 30 fps, use 7200rpm HDD.

(Maximum speed of 5400 rpm HDD is less than 16frame/sec.)

6.2. HDD Installation Procedure

<Note>

When installing and removing HDD, the i-Rec B104’s power should be turned off.

(1) Check that dip switch of HDD is set to “Master” or “Single” mode.

(Default setting of MAXTOR HDD is “Master”)

Page is loading ...

WebGate i-Rec B104 Installation guide

Related papers

Other documents