Seametrics FT430 Quick start guide

Seametrics
Brand
Seametrics
Model
FT430
Type
Quick start guide
The Home Screen
The Home screen displays total ow volume and ow rate. The four buttons below
the LCD display are used to access menu screens for viewing and changing setup
parameters.
Press the check mark key to enter a submenu.
The left/right keys are used to move through the menus and position the cursor during data entry. The up arrow is
used to scroll through the available values that are to be entered. For example, numerical values for K factor entry or
selection of units from the available options. The enter key (represented on the keypad by the check mark) is used to
save selected entries and in conjunction with the exit tab to move between menus screens. As one
navigates the menus, the current parameter setting is shown and instructions are displayed for how to change the
selected parameter.
0.00
0
GPD
MID
The K factor is the number of pulses the ow
sensor provides to the FT430/440/450 for every
gallon of ow. (Note that the decimal is xed at
three places. If you only have two decimal places
for your K-factor, enter a zero for the third digit.
If unable to set K-factor, the unit is “locked”
to prevent tampering. Please contact your
distributor for assistance.)
R UNITSET K T UNIT SET D
SET P RESET EXIT
086238.235
PRESS TO SET NUMBER
OF PULSES RECEIVED PER
GALLON OF FLOW
R UNITSET K T UNIT SET D
SET P RESET EXIT
086238.235
PRESS AND TO CHANGE
AND TO EXIT
Set K Factor
(
SET K
)
View or change the ow rate display units.
R UNITSET K T UNIT SET D
SET P RESET EXIT
FLOW RATE = GPD
PRESS TO SET UNITS
FOR DISPLAY
R UNITSET K T UNIT SET D
SET P RESET EXIT
RATE: GALLONS / MIN
PRESS AND TO CHANGE
Set Rate Display
(
R UNIT
)
FT430/440/450
Quick Start Guide
253.872.0284 Page 1 of 2 seametrics.com
Set Pulses for Pulse Out 1
(
SET P
)
The factory setting will show Set P which allows you to view or change the volume
of ow totalized per pulse sent to pulse out 1. The units for Set P follow the units
selected for the rate display.
(With EXIT highlighted, pressing the up arrow four times will allow Output 1 to be an alarm.
The alarm can be set to trigger on either a high or low ow condition as determined by the user.
Refer to the FT430/440/450 instruction manual for details.)
R UNITSET K T UNIT SET D
SET P RESET EXIT
00000.0 GALLONS
PRESS TO SET NUMBER OF
GALLONS TOTALIZED PER
PULSE SENT OUT PULSE1
Exit & Save Setup
(
EXIT
)
Return to the home screen or the previous menu if in a submenu.
(Pressing the up arrow four times while EXIT is highlighted will bring you to a secondary menu,
allowing you to set alarms, set pulse output 2, change the input and jitter lters, as well as
access protected features. Refer to the FT430/440/450 instruction manual for details.)
R UNITSET K T UNIT SET D
SET P RESET EXIT
PRESS TO EXIT MENU AND
RETURN TO FLOW DISPLAY
View or change the total volume display units.
R UNITSET K T UNIT SET D
SET P RESET EXIT
TOTAL = GALLONS
PRESS TO SET UNITS
FOR DISPLAY
R UNITSET K T UNIT SET D
SET P RESET EXIT
TOTAL: GALLONS
PRESS TO CHANGE
Set Total Display Units
(
T UNIT
)
Set Number of Decimal Places
(
SET D
)
View or change the number of decimals
displayed in the total volume display.
R UNITSET K T UNIT SET D
SET P RESET EXIT
000
PRESS TO CHOOSE
NUMBER OF DECIMAL PLACES
IN TOTAL DISPLAY
R UNITSET K T UNIT SET D
SET P RESET EXIT
PRESS TO CHANGE
000
LT-14244r1.1-20160222
2/22/16
Seametrics • 19026 72nd Avenue South • Kent, Washington 98032 • USA
(P) 253.872.0284 • (F) 253.872.0285 • 1.800.975.8153 • seametrics.com
FT430/440/450
Quick Start Guide
  • Page 1 1
  • Page 2 2

Seametrics FT430 Quick start guide

Seametrics
Brand
Seametrics
Model
FT430
Type
Quick start guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents