Page is loading ...
E3C236D4M-4L
Quick Installation Guide
www.asrockrack.com
No. Description No. Description
1VGA Port (VGA1) 6 LAN RJ-45 Port (LAN2)
2 Serial Port (COM1) 7 LAN RJ-45 Port (LAN3)
3 USB 3.0 Ports (USB3_1_2) 8 LAN RJ-45 Port (LAN4)
4 LAN RJ-45 Port (IPMI_LAN) 9 UID Switch (UID1)
5 LAN RJ-45 Port (LAN1)
4
2
P/N: 15G065084100AK V1.0
Install the Server Board
Motherboard Layout
Jumper Cap On/O
The server board User's Manual is available for download from the ASRock Rack's ofcial website
at http://www.asrockrack.com.
Take note of the following precautions before you install server board components or change any
server board settings.
1. Unplug the power cord from the wall socket before touching any components.
2. To avoid damaging the server board’s components due to static electricity, NEVER place your
server board directly on the carpet or the like. Also remember to use a grounded wrist strap or
touch a safety grounded object before you handle the components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded anti-static pad or in the bag
that comes with the component.
5. When placing screws into the screw holes to secure the server board to the chassis, please do
not over-tighten the screws! Doing so may damage the server board.
1
1Insert the server board into the chassis.
2Aff i x the screws clockwise into t he
mounting holes in all of the corners of
the server board.
Do not over-tighten the screws
When the jumper cap is placed on the pins, the
jumper is “Short”. If no jumper cap is placed on the
pins, the jumper is “Open”.
The illustration shows a 3-pin jumper whose pin1
and pin2 are “Short” when a jumper cap is placed on
these 2 pins.
I/O Panel
DDR3_B1 (64 bit, 240-pin module)
DDR3_A1 (64 bit, 240-pin module)
ATXPWR1
CPU_FAN1
COM1
VGA1
FRNT_FAN1
LAN2
IPMI
LAN
DDR4_B2 (64 bit, 288-pin module)
DDR4_B1 (64 bit, 288-pin module)
DDR3_B1 (64 bit, 240-pin module)
DDR3_A1 (64 bit, 240-pin module)
DDR4_A2 (64 bit, 288-pin module)
DDR4_A1 (64 bit, 288-pin module)
1
PSU_SMB1
ATX12V1
1
1
1
1
1
1
SATA_0
SATA_1
SATA_ 2
SATA_ 3
SATA_ 4
SATA_ 5
SATA_ 6
SATA_ 7
IPMB1
BMC_SMB1
SATAPWR1
REAR_FAN1
LAN1
USB 3.0
T: USB_1
B: USB_2
LAN4
LAN3
1
1
1
1
1
1
FRNT_FAN2
FRNT_FAN3
SATA_PWR1
BAT1
Intel
C236
BUZZER1
Dr.
Debug
PEG_CFG1
1
1
TPM1
PANEL1
1
AUX_PANEL1
HDLED RESET
PLED PWRBTN
1
1
LED_LAN_3_4
USB3_5
USB_1_2
1
1
USB3_3_4
SATA_SGPIO2 SATA_SGPIO1
11
T 1
1
R
11
SEC_OR1
UID1
1
NCSI_SEL1
REAR_FAN2
1
LED_LAN_5_6
123457 8
6910 11 12 13
14
15
16
17
18
19
20
21
22
23
24
25
17.0cm (9.6 in)
E3C236D4M-4L
PCIE6
BIOS
ROM
PCIE2
MEZZ_2
MEZZ_1
NMI_BTN1
PMBUS_SEL_ALT1
PMBUS_SEL_DAT1
PMBUS_SEL_CLK1
CHASSIS_ID1
CHASSIS_ID2
CHASSIS_ID3
ME_RECOVERY1
11
PECI1
30.5cm (12in)
26
27
28
29
30
31
32
333435
36
37
38
39
49
41
42
43
44
45
46
47
48
49
50
BMC
BMC
ROM
Super
I/O
(x16)
(x8)
No. Description
1 Chassis ID1 Jumper (CHASSIS_ID1)
2 Chassis ID2 Jumper (CHASSIS_ID2)
3PMBUS Mode Jumper (PMBUS_SEL_CLK1)
4PMBUS Mode Jumper (PMBUS_SEL_DAT1)
5PMBUS Mode Jumper (PMBUS_SEL_ALT1)
6 Chassis ID3 Jumper (CHASSIS_ID3)
7 Non Maskable Interrupt Button (NMI_BTN1)
8Intelligent Platform Management Bus Header
(IPMB1)
9 ATX 12V Power Connector (ATX12V1)
10 BMC SMBus Header (BMC_SMB1)
11 ME Recovery Jumper (ME_RECOVERY1)
12 PSU SMBus (PSU_SMB1)
13 ATX Power Connector (ATXPWR1)
14 2 x 288-pin DDR4 DIMM Slots (DDR4_A2,
DDR4_B2, Blue)
15 2 x 288-pin DDR4 DIMM Slots (DDR4_A1,
DDR4_B1, White)
16 CPU Fan Connector (CPU_FAN1)
17 Front Fan Connector (FRNT_FAN1)
18 Front Fan Connector (FRNT_FAN2)
19 Front Fan Connector (FRNT_FAN3)
20 CPU PECI Mode Jumper (PECI1)
21 SATA DOM Power Jumper (SATAPWR1)
22 SATA DOM Power Header (SATA_PWR1)
23 SATA3 DOM Connector (SATA_0), Red
24 SATA3 Connector (SATA_1)
25 SATA3 Connector (SATA_2)
26 SATA3 Connector (SATA_3)
27 SATA3 Connector (SATA_5)
28 SATA3 Connector (SATA_4)
29 SATA3 Connector (SATA_7)
30 SATA3 Connector (SATA_6)
31 Flash Descriptor Security Override Jumper
(SEC_OR1)
32 System Panel Header (PANEL1)
33 Auxiliary Panel Header (AUX_PANEL1)
34 USB 2.0 Header (USB_1_2)
35 Vertical Type A USB 3.0 (USB3_5)
36 Mezzaine Card Slot 2 (MEZZ_2)
37 USB 3.0 Header (USB3_3_4)
38 SATA SGPIO Connector (SATA_SGPIO1)
39 SATA SGPIO Connector (SATA_SGPIO2)
40 PCI Express Graphics Conguration Jumper
(PEG_CFG1)
41 ermal Sensor Header (TR1)
42 TPM Header (TPM1)
43 PCIE Card Slot 2 (PCIE2) (x8, from PCH)
44 PCIE Card Slot 6 (PCIE6) (x16, from CPU)
45 Rear Fan Connector (REAR_FAN2)
46 NCSI Mode Jumper (NCSI_SEL1)
47 LAN LED Connector (LED_LAN_3_4)
48 LAN LED Connector (LED_LAN_5_6)
49 Mezzaine Card Slot 1 (MEZZ_1)
50 Rear Fan Connector (REAR_FAN1)
6
5
3
2
1
4
87 9
*15G065084100AK*
3
E3C236D4M-4L
Quick Installation Guide
www.asrockrack.com
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 10M bps connection or no
link
Blinking Green Data Activity O 100M bps connection
On Link Yellow 1Gbps connection
Speed LED Activity / Link LED
Status Description Status Description
O 10Mbps connection or
no link
O No Link
Yel low 100Mbps connection Blinking Green Data Activity
Green 1Gbps connection On Link
8LAN Port LED Indications
5
7
6
123
Open the socket levers and the
CPU socket cover. Remove the
CPU protection cap.
Install the processor and close
the socket cover.
Close the socket levers.
Install the CPU Fan and Heatsink
CPU_FAN
12
Apply the thermal grease. Install the
CPU fan and heatsink and secure
the screws.
Connect the CPU fan to the CPU
FAN connector.
Install the Power Cables
Install the Processor
9Install the PCIE Card
We recommend using the CPU Installation tool to avoid CPU pin-bent problem.
A
B
3V
3V
GND
GND
5V
5V
GND
PWROK_PS
5VSB
12V
12V
3V
121
13 24
3V
-12V
GND
PSON#
GND
GND
GND
5V
5V
5V
GND
N/A
System Panel Auxiliary Panel
12 Headers
GND
RESET#
PWRBTN#
PLED-
PLED+
GND
HDLED-
HDLED+
1
GND
11 Install the Memory
1
2
3
Unlock a DIMM slot by pressing the
module clips outward.
Insert the memory module.
Lock the clips.
ACT/LINK LED
SPEED LED
LAN Port
ACT/LINK LED
SPEED LED
LAN Port
IPMI LAN Port
1G LAN Port
4
8
1
5
+12V2
GND
GND
SMB_CLK
SMB_Alert
CASEOPEN
1
SMB_DATA
+3VSB
LAN1_LINK
LED_PWR
LAN2_LINK
LED_PWR
+5VSB
GND
GND
LOCATORLED1+
LOCATORLED1-
LOCATORBTN#
System Fault LED-
AB
CD
System Fault LED+
E
1Remove the bracket facing the slot that
you intend to use. Keep the screw for
later use.
2Align the card connector with the
slot and press firmly until the card is
completely seated on the slot.
Fasten the card to the chassis with the
screw.
3
Dr. Debug
Code Description
00 Please check if the CPU is installed correctly and then clear CMOS.
0d Problem related to memory, VGA card or other devices. Please clear CMOS, re-install the memo-
ry and VGA card, and remove other USB, PCI devices.
01 - 54
(except 0d),
5A- 60
Problem related to memory. Please re-install the CPU and memory then clear CMOS. If the
problem still exists, please install only one memory module or try using other memory modules.
55 e Memory could not be detected. Please re-install the memory and CPU. If the problem still
exists, please install only one memory module or try using other memory modules.
61 - 91 Chipset initialization error. Please press reset or clear CMOS.
92 - 99 Problem related to PCI-E devices. Please re-install PCI-E devices or try installing them in other
slots. If the problem still exists, please remove all PCI-E devices or try using another VGA card.
A0 - A7 Problem related to IDE or SATA devices. Please re-install IDE and SATA devices. If the problem
still exists, please clear CMOS and try removing all SATA devices.
b0 Problem related to memory. Please re-install the CPU and memory. If the problem still exists,
please install only one memory module or try using other memory modules.
b4 Problem related to USB devices. Please try removing all USB devices.
b7 Problem related to memory. Please re-install the CPU and memory then clear CMOS. If the
problem still exists, please install only one memory module or try using other memory modules.
d6 e VGA could not be recognized. Please clear CMOS and try re-installing the VGA card. If the
problem still exists, please try installing the VGA card in other slots or use other VGA cards.
d7 e Keyboard and mouse could not be recognized. Please try re-installing the keyboard and
mouse.
d8 Invalid Password.
FF Please check if the CPU is installed correctly and then clear CMOS.
10
Slot Generation Mechanical Electrical Source
PCIE 6 3.0 x16 x16 CPU
PCIE 2 3.0 x8 x4 PCH
PCIE6
No mezzanine card x16
MEZZ_1 is populated x8
MEZZ_2 is populated N/A
/