AMG AMG2256 Instruction Sheet

AMG
Brand
AMG
Model
AMG2256
Category
Video switches
Type
Instruction Sheet

This manual is also suitable for

AMG AMG2256S is a rackmount video receiver with bi-directional FTT10A data and a single fiber connection. It has a front panel with indicators for opto in, sync, video, audio, data, fiber transceiver, power, and DC in. The video connection uses a 75 ohm BNC socket with an output impedance of 75 ohms terminated and an output level of 1 volt p-p nominal. The optical connection uses an ST Style connector with a receiver sensitivity of -17dBm to -30dBm nominal for high gain and -9dBm to -22dBm nominal for low gain.

AMG AMG2256S is a rackmount video receiver with bi-directional FTT10A data and a single fiber connection. It has a front panel with indicators for opto in, sync, video, audio, data, fiber transceiver, power, and DC in. The video connection uses a 75 ohm BNC socket with an output impedance of 75 ohms terminated and an output level of 1 volt p-p nominal. The optical connection uses an ST Style connector with a receiver sensitivity of -17dBm to -30dBm nominal for high gain and -9dBm to -22dBm nominal for low gain.

AMG Systems Ltd. reserves the right to make changes to this document without notice.
The information herein is believed to be accurate. No responsibility however is assumed
by AMG for its use.
Page 1 of 2 D04230-00
AMG2256S
Instruction Sheet
AMG2256S Rackmount Video Receive + Bi-directional FTT10A Data Single fibre
Video Connection
Connectors ...........................75 ohm BNC Socket.
Output Impedance ................75 ohm terminated.
Output Level.........................1 volt p-p nominal.
Frequency Response.............10Hz to 6MHz min.
Optical Connection
Connectors............................ST Style (1 off)
Opto In Receiver Sensitivity
High Gain......................-17dBm to –30dBm nominal.
Low Gain.......................-9dBm to –22dBm nominal.
(Unless otherwise specified units will be shipped in the low gain range)
(for adjustment see below)
Wavelength...........................850/1300nm nominal.
Data Connection
Connector .............................Push-in connector strip- 11way
(Solid conductors 0.5mm2(20 awg) can be connected by simply push fitting
into the appropriate connection hole. Smaller conductors and wires (up to
0.5mm2, 20 awg) are inserted into the connection space whilst depressing the
orange lever. Wire or conductors should be stripped back to a length of
11mm. Use a small screwdriver to depress the orange lever to release the
connection.)
VIDEO OUT
OPTO IN
VISION2000
FIBRE
PL1
DC IN
TRANSCEIVER
+15V @ 200mA
FRONT PANEL INDICATORS
SYNC
VIDEO
POWER
AUDIO
DATA
OPTO OUT
PIN 1
~193mm
~54mm
Slot size 4.5mm x 10mm
~100mm
~200mm
AMG Systems Ltd. reserves the right to make changes to this document without notice.
The information herein is believed to be accurate. No responsibility however is assumed
by AMG for its use.
Page 2 of 2 D04230-00
Pinout ...................................See Below – Note Pins number from the bottom of the unit
Pin No. Function
1(bottom) N/C
2 N/C
3 N/C
4 N/C
5 Power Ground
6 Auxiliary Power Input ( +15v to +18v dc )
Data
Interface FTT10A
7 (TTL Data Ground)
8 (TTL Data Out)
9 (TTL Data In)
10 FTT10A NODE A
11 FTT10A NODE B
Dimensions
Height ...................................3U
Width....................................7HP
Depth ....................................205mm
Mounting Details
The AMG2256S plugs into and is powered from the AMG2000 Subrack
Indicators
Power....................................Green – lit when unit powered
Video Sync ...........................Green – lit when video signal present on optical input.
Data Sync ............................. Green – lit when data channel present.
(Note: this does not indicate the presence of actual data)
Gain Range Setting
If required the receiver gain range can be adjusted by changing jumper positions on the PCB.
The high gain setting is for long distances over small fibres, and the low gain setting for larger
diameter fibres over short distances. Units are shipped in the low gain setting unless otherwise
instructed. The circuit board assembly is removed by removing screws A and B on the rear
panel of the plug-in and sliding the assembly out of the case. Screw C should not be removed
under any circumstances. See above for typical power levels for each range.
LEDs
VIDEO
DATA
POWER
A
B
C
Position 11
Position 1
JP2
High Gain
Low Gain
JP1
  • Page 1 1
  • Page 2 2

AMG AMG2256 Instruction Sheet

AMG
Brand
AMG
Model
AMG2256
Category
Video switches
Type
Instruction Sheet
This manual is also suitable for

AMG AMG2256S is a rackmount video receiver with bi-directional FTT10A data and a single fiber connection. It has a front panel with indicators for opto in, sync, video, audio, data, fiber transceiver, power, and DC in. The video connection uses a 75 ohm BNC socket with an output impedance of 75 ohms terminated and an output level of 1 volt p-p nominal. The optical connection uses an ST Style connector with a receiver sensitivity of -17dBm to -30dBm nominal for high gain and -9dBm to -22dBm nominal for low gain.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers