Ledalite SHINE Install Instructions

Type
Install Instructions

Ledalite Shine and SilkSpace definition are standalone lighting fixtures that can be installed in T-Grid ceilings or drywall ceilings. They come with their own drivers and receive a direct power feed. The fixtures can be mounted in a variety of ways, including using the provided mounting tabs, sheet metal screws, or hanger wires. The fixtures also come with optional flex whips for electrical connections. The lenses can be removed for easy cleaning or replacement.

Ledalite Shine and SilkSpace definition are standalone lighting fixtures that can be installed in T-Grid ceilings or drywall ceilings. They come with their own drivers and receive a direct power feed. The fixtures can be mounted in a variety of ways, including using the provided mounting tabs, sheet metal screws, or hanger wires. The fixtures also come with optional flex whips for electrical connections. The lenses can be removed for easy cleaning or replacement.

www.ledalite.com
page11/12/2019 1
Recessed
ID-33 & ID-42
Shine & SilkSpace definition
Standalone Installation Instructions
Imperial & Metric Sizes
Clip for 1-11/16”
T-Bar height
Clip for 1-1/2” or
1-3/4” bolt slot
grid T-Bar height
Preparing fixtures for mounting
1Bend mounting tab
Bend out mounting tab 90°on each corner.
2Adjust height of tab
Use side cutters to adjust each tab to height
of T-Grid.
3Filler panel (20”x4’ only)
If installing in a 20"x60" T-Grid ceiling,
attach filler panels to ends of the housing
using supplied screws, as shown above.
Mounting in a T-Grid ceiling
4Lay fixture into T-Grid
Lay fixture into T-Grid.
5Bend tabs flush
Bend tabs flush against T-Grid in order to
clear for ceiling tile.
6Fasten fixture to T-Grid
Use #8x1/4” sheet metal screws to fasten
fixture to T-Grid and use a hanger wire to
tie off appropriately in accordance with
local building codes. (Screws and hanger
wires supplied by others).
Driver Driver
Every fixture contains its own driver
and receives a direct power feed.
Power feed
Driver
page
11/12/2019 2www.ledalite.com
Fixtures size A B
2’x2’ 24 ” (626mm) 24 ” (626mm)
2’x4’ 24 ” (626mm) 48 ” (1235mm)
1’x4’ 12 ” (321mm) 48 ” (1235mm)
Mounting in a drywall ceiling
7Drywall ceiling cut out
Cut a hole in the drywall with according to
the dimensions in the table above.
8Installing mounting frame
Insert mounting frame into hole and secure
as shown in step 9.
9Mounting options
Secure mounting frame by screwing to
wood frame or attaching hangar wires.
Making electrical connections & lens installation
10 Electrical connections
Make all electrical connections to the
fixture. For flex whip option, see step 11.
11 Flex Whip (optional)
Optional Flex whip is prewired inside
fixture. Remove packaging and insert snap-
in fitting into wiring cover and complete
electrical connections at other end of whip.
12 Installing Lenses
1. Remove & recycle cardboard shipping
insert holding lenses in place.
2. Slide second lens across to enclose
fixture cavity.
!ATTENTION: Install in accordance with local and national building and electric codes.
1
2
Note: Image shows SilkSpace definition, instructions
are the same for Shine
Standalone Installation InstructionsID-33 & ID-42
  • Page 1 1
  • Page 2 2

Ledalite SHINE Install Instructions

Type
Install Instructions

Ledalite Shine and SilkSpace definition are standalone lighting fixtures that can be installed in T-Grid ceilings or drywall ceilings. They come with their own drivers and receive a direct power feed. The fixtures can be mounted in a variety of ways, including using the provided mounting tabs, sheet metal screws, or hanger wires. The fixtures also come with optional flex whips for electrical connections. The lenses can be removed for easy cleaning or replacement.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI