rollease acmeda Channel Guide Installation guide

Type
Installation guide
Skyline Bottom Up
INSTALLATION MANUAL
v3.0 | September 2023
CHANNEL GUIDE
INSTALLATION MANUAL
CONTENTS
DISCLAIMER
INTRODUCTION
This Installation manual for Channel Guide has been produced by Rollease Acmeda to supply the necessary information for the safe and correct installation of
Channel Guide.
DISCLAIMER
Rollease Acmeda has used reasonable care in preparing the information included in this document, but makes no representations or warranties as to the
completeness or accuracy of the information. Information is supplied upon the condition that the persons receiving the information will make their own
determination as to its suitability for their purposes prior to use. Rollease Acmeda assumes no liability whatsoever for any damages incurred by you resulting from
errors in or omissions from the information included herein. Rollease Acmeda reserves the right to make changes without further notice to any products to improve
reliability, function or design.
COPYRIGHT
COPYRIGHT © ROLLEASE ACMEDA
All rights are reserved. No part of this document may be reproduced or utilised in any means, by any means, electronic or mechanical including photocopying,
recordings, or by any information storage or retrieval system, without the express permission from Rollease Acmeda.
SECTION A | TOOLS AND ADDITIONAL ITEMS REQUIRED
3
PART A  TOOLS REQUIRED ........................................................................................................................3
PART B  ADDITIONAL ITEMS REQUIRED (NOT SUPPLIED) ...................................................................3
PART C  BLIND ITEMS REQUIRED ...........................................................................................................3
SECTION B | INSTALLATION
4
PART A  PREPARING INSTALLATION SPACE .............................................................................................4
PART B  BOX INSTALLATION ........................................................................................................................6
PART C  OPEN BRACKET INSTALLATION ...........................................................................................................6
PART D  BLIND INSTALLATION ........................................................................................................................7
PART E  SIDE GUIDE INSTALLATION ...........................................................................................................9
PART F  WEIGHT BAR SB07 LATCH INSTALLATION ..............................................................................13
PART G  INSERT BOX COVER ......................................................................................................................15
Page. 3
Channel Guide Installation Manual | v3.0 | September 2023
©Copyright All Rights Reserved Rollease Acmeda
SECTION A | TOOLS AND ADDITIONAL ITEMS REQUIRED
PART A – TOOLS REQUIRED
PART B – ADDITIONAL ITEMS REQUIRED (NOT SUPPLIED)
• Saw
• Drill
Drill Bits
Screw Driver – Philips Head
• Scissors
Measuring Tape
To install a Channel Guide the following non-stocked items are required:
Fixings for Box/Open Brackets/Hardware (ensure appropriate fixings are used to suit application)
Trims to conceal packing (if required)
PART C – BLIND ITEMS REQUIRED
BOX FASCIA COVER
A Box 120 off-cut may be required to support the front cover
over wider spans.
NOTE: Store clip until required (can be
left in adaptor as shown)
OPEN BRACKETS BLIND SIDE CHANNELS
Page. 4 Channel Guide Installation Manual | v3.0 | September 2023
©Copyright All Rights Reserved Rollease Acmeda
SECTION B | INSTALLATION
PART A – PREPARING INSTALLATION SPACE
STEP 1  CHECK FOR OBSTRUCTIONS
STEP 2  CHECK TOP OF INSTALLATION IS LEVEL
STEP 3  PACK AND LEVEL TOP OF INSTALLATION TO SMALLEST DROP DIMENSION
Check for any obstructions that may interfere in installation.
E.g. If there is an architrave at the bottom of a post that the Zipscreen is to be installed into, ensure you prepare the space for the
installation.
This may mean that the installer needs to cut into the architrave to make room for the side rails.
If uneven go to step 3
If level go to step 4
D = Drop of Blind
NOTE: In some instances, when the drop is level D1 & D2
will not be equal as there is an uneven ground.
Ensure the smallest value of D1 & D2 = Blind Drop (D
specified in initial measurement)
Where there is uneven ground, side rails may be
supplied in different lengths for a better aesthetical
finish to blind
D1 D2
D1 D2
D1 D2
D1 D2
D1 D2
D1 D2
Page. 5
Channel Guide Installation Manual | v3.0 | September 2023
©Copyright All Rights Reserved Rollease Acmeda
SECTION B | INSTALLATION
STEP 4  CHECK HORIZONTAL INSTALLATION DIMENSION AT TOP, CENTRE & BOTTOM
MEASURING TIPS
2040DROP (mm)
LEFT RIGHT
2000
W1
W2
BLIND WIDTH = W1
BLIND WIDTH = W2
W1
W2
W1
W2
W = Width of blind
If W1 & W2 are equal or within 5mm of each other, proceed to
Step 5.
If W1 & W2 are not equal or within 5mm of each other,
packing may be required to ensure Channel Guides are level.
2040DROP (mm)
LEFT RIGHT
2000
W1
W2
BLIND WIDTH = W1
BLIND WIDTH = W2
W1
W2
W1
W2
2040DROP (mm)
LEFT RIGHT
2000
W1
W2
BLIND WIDTH = W1
BLIND WIDTH = W2
W1
W2
W2
Page. 6 Channel Guide Installation Manual | v3.0 | September 2023
©Copyright All Rights Reserved Rollease Acmeda
FACE FIX
SECTION B | INSTALLATION
STEP 1  INSTALL BOX TO WALL/CEILING
FACE FIX
TOP FIX
TOP FIX
SIDE FIX
SIDE FIX
PART B – BOX INSTALLATION
NOTE:
Use appropriate fixings to suit application. Ensure Box is Aligned and Level.
Ensure 2 fasteners are used per side.
NOTE:
Use appropriate fixings to suit application. Ensure Box is Aligned and Level.
Ensure 2 fasteners are used per side.
Ensure brackets are aligned and level.
Measure brackets end to end to confirm measurement is correct.
PART C – OPEN BRACKET INSTALLATION
STEP 1  INSTALL BRACKETS TO WALL/CEILING
Page. 7
Channel Guide Installation Manual | v3.0 | September 2023
©Copyright All Rights Reserved Rollease Acmeda
PART D – BLIND INSTALLATION
STEP 1  INSERT BLIND INTO BOX
STEP 2  INSERT RETAINER CLIP MKII ONTO IDLER ADAPTER
IDLER END
Ensure pin is clipped in securely
Tighten the Screw
SECTION B | INSTALLATION
User effort will be required to push the booster head/Idler pin into the adapter,
a noticeable “click” will indicate that the component is correctly located.
Page. 8 Channel Guide Installation Manual | v3.0 | September 2023
©Copyright All Rights Reserved Rollease Acmeda
STEP 3  FEED THROUGH MOTOR CABLE (FOR MOTOR ONLY)
STEP 4 RUN BLIND DOWN + CENTRE
SECTION B | INSTALLATION
Page. 9
Channel Guide Installation Manual | v3.0 | September 2023
©Copyright All Rights Reserved Rollease Acmeda
STEP 1  MARK OUT SIDE GUIDE POSITION AND ALIGN RAIL (FOR OPEN BRACKET ONLY)
STEP 2  LOCATE CHANNEL FIXING RAIL TO EAR FOR CORRECT POSITION
NOTE: Line up side guide with edge of bracket
NOTE: Lift out fabric & weight bar to insert fabric into side guides
PART E – SIDE GUIDE INSTALLATION
FACE FIX
TOP FIX
SECTION B | INSTALLATION
Page. 10 Channel Guide Installation Manual | v3.0 | September 2023
©Copyright All Rights Reserved Rollease Acmeda
STEP 3  FIX SIDE GUIDES
RECESS FIX
RECESS FIX
NOTE: Use grooves in fixing rail to centre fixing positions
NOTE: Ensure side guides are vertical and parallel using a spirit level
NOTE: Use grooves in fixing rail to centre fixing positions
NOTE: Ensure side guides are vertical and parallel using a spirit level
SECTION B | INSTALLATION
Page. 11
Channel Guide Installation Manual | v3.0 | September 2023
©Copyright All Rights Reserved Rollease Acmeda
STEP 4  INSERT SIDE GUIDE FRONT COVERS
STEP 5  USE A FLAT HEAD SCREW DRIVER TO SECURE THE SIDE GUIDES TOGETHER
NOTE: Ensure side guide locks are vertical on extrusion
Unlocked Position:
Rotate Clockwise to Lock
SECTION B | INSTALLATION
Locked Position:
Page. 12 Channel Guide Installation Manual | v3.0 | September 2023
©Copyright All Rights Reserved Rollease Acmeda
STEP 6  TEST BLIND TO ENSURE IT IS OPERATING CORRECTLY
SECTION B | INSTALLATION
Run blind down and up to ensure correct operation
Page. 13
Channel Guide Installation Manual | v3.0 | September 2023
©Copyright All Rights Reserved Rollease Acmeda
STEP 1  BRING WEIGHT BAR TO DESIRED LOCKED POSITION
STEP 2  SECURE LATCH TO CHANNEL COVER RAIL
NOTE: Ensure shaft of the lock is retracted
SECTION B | INSTALLATION
PART F – WEIGHT BAR SB07 LATCH INSTALLATION
HD82-2366-010008 screws must be used with locks
(#6 x 8mm)
NOTE: Align lip of latch to Mounting Rail
Page. 14 Channel Guide Installation Manual | v3.0 | September 2023
©Copyright All Rights Reserved Rollease Acmeda
STEP 3  ADD ADDITIONAL LATCHES (IF REQUIRED)
SECTION B | INSTALLATION
Page. 15
Channel Guide Installation Manual | v3.0 | September 2023
©Copyright All Rights Reserved Rollease Acmeda
STEP 1  SWING BOX COVER INTO BOX TOP AND CLIP INTO PLACE
STEP 2  SECURE COVER AT BOTH ENDS
TOP LIMIT: Set top limit as required (should be as close to the box as possible)
SECTION B | INSTALLATION
PART G – INSERT BOX COVER
Page. 16 Channel Guide Installation Manual | v3.0 | September 2023
©Copyright All Rights Reserved Rollease Acmeda
INSTALLED CHANNEL
BOX
OPEN
SECTION B | INSTALLATION
Page. 17
Channel Guide Installation Manual | v3.0 | September 2023
©Copyright All Rights Reserved Rollease Acmeda
DOCUMENT CHANGE NOTES
REVISION CHANGES
v2.2 | August 2022 Removed 63mm spring tension chart.
v3.0 | September
2023 Removed spring compatibility
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17

rollease acmeda Channel Guide Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI