Wallenstein P600 Installation guide

Brand: Wallenstein

Model: P600

Type: Installation guide

This manual is also suitable for

P601 6 Way Wedge

Wallenstein P600 is a time-saving 6 Way Wedge that splits wood into smaller more manageable pieces.

The Wallenstein P600 is a heavy-duty tool constructed of heavy gauge steel. It is designed to fit specific Wood Processor models: WP230, WP260, WP630, WP820, WP830, and WP860. The P600 comes completely assembled and is easy to install.

To install the Wallenstein P600, first ensure that the Wood Processor is not powered on and is resting on dry level ground. Then, follow the detailed instructions provided in the manual.

Once installed, the Wallenstein P600 is ready to use. Simply lift the wedge into position and insert it into the chute. The wedge will then split the wood into smaller pieces.

Wallenstein P600 is a time-saving 6 Way Wedge that splits wood into smaller more manageable pieces.

To install the Wallenstein P600, first ensure that the Wood Processor is not powered on and is resting on dry level ground. Then, follow the detailed instructions provided in the manual.

Once installed, the Wallenstein P600 is ready to use. Simply lift the wedge into position and insert it into the chute. The wedge will then split the wood into smaller pieces.

Caution: wedge is constructed of heavy

gauge steel, be sure to use caution moving and

installing the kit, avoid dropping or pinching body

parts on corners and edges of the kit.

P600 / P601 kits comes completely assembled.

Although the kits t specic models, installation

procedure is the same for both, follow the instruc-

tions to complete the installation.

Before you start, you’ll need:

• Rags.

6 Way Wedge Installation:

Kit P600 (2089W571): ts Wood Processor models: WP230,

WP260, WP630, WP820, WP830 and WP860.

Kit P601 (2089W572): ts Wood Processor models: WP235,

WP265, WP635, WP825, WP835 and WP865.

Accessory Installation Instructions

EMB Manufacturing Inc.

4144 Boomer Line · St. Clements, On · N0B 2M0 · Canada

Ph: (519) 699-9283 · Fax: (519) 699-4146

www.embmfg.com

6-WAY WEDGE

This Safety Alert symbol means

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

The Safety Alert symbol identies important safety messages in this instruction, as well as on the Wood Processor and in

the operators manual. When you see this symbol, be alert to the possibility of personal injury or death. Follow the in-

structions in the safety message.

Always wear the appropriate safety gear when installing this kit or working around the machine. This includes but is

not limited to:

• Hard hat for protection to the head.

• Face mask for protection to the face and eyes from ying chips.

• Heavy gloves for protection from slivers, chips and pinching.

• Safety shoes with slip resistant soles and steel toes.

over:

Time saving 6 Way Wedge, splits wood into smaller more manageable pieces

This Instruction applies to Way Wedge kit:

P600 (2089W571)

P601 (2089W572)

For replacement parts, go to www.embmfg.com and click on "Parts and Manuals" to download the latest parts manual for

your model, then call your dealer to order.

Installation Instructions:

Ensure the Wood Processor is not powered on, and the area around it is clean and free of debris and resting on

dry level ground. Clean any debris on or around the 4 way wedge.

1. Facing the hydraulic controls, move the wedge height lever all the way

to the right, to take the tension off of the lever and lower the wedge to a

safe position for removal.

2. Find where the wedge attaches to the height lever, and remove the

latch pin.

3. On the far side of the wedge, Carefully grasp the hitch pin and remove

it and the roller sleeve from the wedge.

4. The wedge is now free to remove.

5. Find the splitter chute height adjuster and remove the latch pin, then

carefully grasp the hitch pin and remove it from height adjuster.

6. You will then be able to raise the splitter chute up into its folded posi-

tion, to gain access to the wedge.

7. Lift the wedge straight up till it clears the chute bottom, then lift the

wedge out of the chute area.

8. Grab the 6 way wedge by the lifting handle and lift it into position, make

sure the wedge is oriented properly, line up with the wedge support and

insert it where the 4 way wedge was.

9. Set the wedge down, then align and insert the roller sleeve in the slot

at the bottom of the wedge, install the hitch pin through the sleeve, and

install the latch pin.

10. Lower the splitter chute back into position, then replace the hitch pin and

latch pin onto the height adjuster .

11. Ensure the height lever and wedge move freely, and everything is secure.

Your new 6 way wedge is ready to use.

tooltip

PRINTED IN CANADA

Rev: 080715 PART NUMBER: Z97803

height lever

latch pin

tooltip

Cutaway view showing 6 Way

Wedge aligned with wedge

support during insertion

Caution lifting hazard

Caution pinching hazard

6 Way Wedge

wedge support

Splitter

Chute

roller slot

hitch pin

roller pin

height adjuster

hitch pin

Wallenstein P600 Installation guide

Brand: Wallenstein

Model: P600

Type: Installation guide

This manual is also suitable for

P601 6 Way Wedge

Wallenstein P600 is a time-saving 6 Way Wedge that splits wood into smaller more manageable pieces.

To install the Wallenstein P600, first ensure that the Wood Processor is not powered on and is resting on dry level ground. Then, follow the detailed instructions provided in the manual.

Once installed, the Wallenstein P600 is ready to use. Simply lift the wedge into position and insert it into the chute. The wedge will then split the wood into smaller pieces.

Download PDF

report

Wallenstein P600 Installation guide

This manual is also suitable for

Wallenstein P600 Installation guide

Related papers

Other documents