EN
English - Instruction manual
IT
Italiano - Manuale di istruzioni
FR
Français - Manuel d’instructions
DE
Deutsch - Bedienungsanleitung
RU
Русский - Руководство по эксплуатации
ITALIANO
NXM36 Hi-PoE
Housing for IP cameras for installation in aggressive environments
Page is loading ...
EN
English - Instruction manual
ENGLISH
NXM36 Hi-PoE
Housing for IP cameras for installation in aggressive environments
EN - English - Instruction manual
2 MNVCNXM36POE_2021_EN
Contents
ENGLISH 1
1 About this manual ....................................................................................................................3
1.1 Typographical conventions ................................................................................................................................................ 3
2 Notes on copyright and information on trademarks .............................................................3
3 Safety rules................................................................................................................................3
4 Identication .............................................................................................................................4
4.1 Product description and type designation ................................................................................................................... 4
4.2 Product marking ..................................................................................................................................................................... 4
5 Preparing the product for use .................................................................................................4
5.1 Unpacking ................................................................................................................................................................................. 4
5.2 Contents .................................................................................................................................................................................... 4
5.3 Safely disposing of packaging material ......................................................................................................................... 4
6 Installation ................................................................................................................................4
6.1 Housing opening .................................................................................................................................................................... 4
6.2 How to install the camera .................................................................................................................................................... 5
6.3 Connection of the PoE power supply board ................................................................................................................ 5
7 Conguration ............................................................................................................................5
7.1 Power consumption conguration .................................................................................................................................. 5
7.2 Operating status ..................................................................................................................................................................... 6
7.3 Housing closure ...................................................................................................................................................................... 6
7.4 Installing the housing ........................................................................................................................................................... 7
7.4.1 Sunshield mounting (optional) ..........................................................................................................................................................7
8 Cleaning ....................................................................................................................................7
8.1 Cleaning the window ............................................................................................................................................................ 7
9 Information on disposal and recycling ...................................................................................7
10 Technical data .........................................................................................................................8
10.2 Mechanical ............................................................................................................................................................................. 8
10.3 Housing's window ............................................................................................................................................................... 8
10.4 Electrical .................................................................................................................................................................................. 8
10.5 Environment .......................................................................................................................................................................... 8
10.6 Certications .......................................................................................................................................................................... 8
11 Technical drawings ................................................................................................................. 9
Instruction manual - English - EN
3MNVCNXM36POE_2021_EN
1 About this manual
Read all the documentation supplied carefully before
installing and using this unit. Keep the manual in a
convenient place for future reference.
1.1 Typographical conventions
DANGER!
High level hazard.
Risk of electric shock. Disconnect the
power supply before proceeding with any
operation, unless indicated otherwise.
CAUTION!
Medium level hazard.
This operation is very important for the
system to function properly. Please read
the procedure described very carefully and
carry it out as instructed.
INFO
Description of system specications.
We recommend reading this part carefully
in order to understand the subsequent
stages.
2 Notes on copyright and
information on trademarks
The mentioned names of products or companies are
trademarks or registered trademarks.
3 Safety rules
CAUTION! Device installation and
maintaining must be performed by
specialist technical sta only.
CAUTION! The electrical system to which the
unit is connected must be equipped with a
10A max automatic bipolar circuit breaker.
The minimum distance between the circuit
breaker contacts must be 3mm (0.1in).
The circuit breaker must be provided
with protection against the fault current
towards the ground (dierential) and the
overcurrent (magnetothermal).
• The manufacturer declines all responsibility
for any damage caused by an improper use
of the appliances mentioned in this manual.
Furthermore, the manufacturer reserves the right
to modify its contents without any prior notice.
The documentation contained in this manual has
been collected and veried with great care. The
manufacturer, however, cannot take any liability
for its use. The same thing can be said for any
person or company involved in the creation and
production of this manual.
• Before starting any operation, make sure the
power supply is disconnected.
• Be careful not to use cables that seem worn or old.
• Never, under any circumstances, make any
changes or connections that are not shown in
this handbook. Improper use of the appliance
can cause serious hazards, risking the safety of
personnel and of the installation.
• Use only original spare parts. Non-original spare
parts could cause re, electrical discharge or other
hazards.
• Before proceeding with installation, check the
supplied material to make sure it corresponds
to the order specication by examining the
identication labels (4.2 Product marking, page 4).
• Equipment intended for installation in Restricted
Access Location performed by specialist technical
sta.
EN - English - Instruction manual
4 MNVCNXM36POE_2021_EN
4 Identication
4.1 Product description and type
designation
The NXM36 Hi-PoE housing has been developed
for installations in highly corrosive areas such
as industrial chemical, petrochemical, marine,
naval and oshore platforms. Entirely made from
electropolished and passivated AISI 316L stainless
steel for maximum protection against deterioration.
The IP66/IP67/IP68/IP69 level guarantees complete
protection against bad weather and water immersion.
The NXM36 Hi-PoE housing exploits the PoE and Hi-
PoE technology in an optimal way, using the power
provided by the Ethernet cable as the sole source of
electricity to power the network camera along with
heating/demisting.
NXM36 Hi-PoE can be congured via a dip switch
according to the PoE or Hi-PoE standards depending
to the system requirements.
The accessories of wiper and water pump ensure a
constant cleaning of the front window.
The NXM36 Hi-PoE housing can be installed on
NXPTH Pan & Tilt head, to obtain a complete
positioning system.
4.2 Product marking
See the label attached to the product.
5 Preparing the product for
use
Any change that is not expressly approved
by the manufacturer will invalidate the
guarantee.
5.1 Unpacking
When the product is delivered, make sure that the
package is intact and that there are no signs that it
has been dropped or scratched.
If there are obvious signs of damage, contact the
supplier immediately.
When returning a faulty product we recommend
using the original packaging for shipping.
Keep the packaging in case you need to send the
product for repairs.
5.2 Contents
Check the contents to make sure they correspond
with the list of materials as below:
• Housing
• Housing equipment:
• Allen wrench
• Spacers
• Bolts and screws
• Instruction manual
5.3 Safely disposing of packaging
material
The packaging material can all be recycled. The
installer technician will be responsible for separating
the material for disposal, and in any case for
compliance with the legislation in force where the
device is to be used.
6 Installation
6.1 Housing opening
Unscrew the screws (01) on the rear ange (02) using
the hexagonal wrench (03) provided.
02 0301
Fig. 1
Slide out the rear cover plate of the housing, taking
care to leave the sealing washer in its seating.
Fig. 2
Instruction manual - English - EN
5MNVCNXM36POE_2021_EN
6.2 How to install the camera
Assemble the camera on the slide using the
insulating spacer (01) and the 1/4” screw and the
washer (02) provided. If necessary, use the spacers to
position the camera and lens correctly.
Fig. 3
Insert the cables through the cable glands and
electrically connect.
Ensure the cable glands are rmly fastened.
6.3 Connection of the PoE power
supply board
Connect the PoE cable from the Power Injector to the
J1 connector.
Connect the camera to the J2 connector.
J2
J1
Fig. 4
7 Conguration
7.1 Power consumption
conguration
Before powering the device, you must set the
maximum power consumption of the housing
operating on dip switch SW1.
SW1
Fig. 5
POWER CONSUMPTION CONFIGURATION
SW1 Maximum power
POE PoE, class 3 (13W max)
POE+ Hi-PoE, class 4 (25W max)
Tab. 1
EN - English - Instruction manual
6 MNVCNXM36POE_2021_EN
7.2 Operating status
The LEDs shown in the gure allow to check the
product's operating status.
LD3
LD1
LD2
Fig. 6
Refer to the table to identify the operating status.
OPERATING STATUS
LED LED Status Apparatus Status
LD1 (Ca
-
mera)
O The camera is not connected
On The camera is correctly powered
1 ashing The camera has a low identication
resistance
2 ashings The camera has a high identica
-
tion resistance
5 ashings The camera has an excessive ener
-
gy consumption
9 ashings The camera requires more energy
than the available
LD2 (Power
supply)
O The device is not powered
On The device is correctly powered
LD3 (Heater) O Heating is inactive
On Heating is active
Tab. 2
7.3 Housing closure
Before closing the housing reinsert the bottom
orientating the slide according to the installation
required, on the wall bracket or on the Pan & tilt
head, for the right camera tting (7.4 Installing the
housing, page7).
Pay attention not to damage the gasket.
Make sure that the sealing ring is correctly tted in
its position.
Pay attention to the xing. Tightening
torque: 2.1Nm.
Instruction manual - English - EN
7MNVCNXM36POE_2021_EN
7.4 Installing the housing
Before closing the housing, be sure to have rightly
tted the internal slide according to the type of
installation.
Fig. 7 Bracket mounting.
Fig. 8 P&T installation.
7.4.1 Sunshield mounting (optional)
Between the sunshield and the anges of the
housing, position the spacers supplied. Then,
fasten the sunshield to the housing with the screws
supplied, corresponding to the spacers.
Fig. 9
8 Cleaning
8.1 Cleaning the window
Avoid ethyl alcohol, solvents, hydrogenated
hydrocarbide, strong acid and alkali. Such
products may irreparably damage the
surface.
We recommend using a soft cloth with neutral soap
diluted with water or specic products to clean the
glasses lenses.
The device should be cleaned using a damp cloth;
compressed air must not be used.
9 Information on disposal
and recycling
The European Directive 2012/19/EU on Waste
Electrical and Electronic Equipment (WEEE) mandates
that these devices should not be disposed of in the
normal ow of municipal solid waste, but they should
be collected separately in order to optimize the
recovery stream and recycling of the materials that
they contain and to reduce the impact on human
health and the environment due to the presence of
potentially hazardous substances.
The symbol of the crossed out bin is marked
on all products to remember this.
The waste may be delivered to appropriate collection
centers, or may be delivered free of charge to the
distributor where you purchased the equipment at
the time of purchase of a new equivalent or without
obligation to a new purchase for equipment with size
smaller than 25cm (9.8in).
For more information on proper disposal of these
devices, you can contact the responsible public
service.
EN - English - Instruction manual
8 MNVCNXM36POE_2021_EN
10 Technical data
10.2 Mechanical
The housing is in austenitic alloy stainless steel,
corrosion and heat resistant according to the
following standards:
• AISI 316L
• UNI 6900-71: X 2 Cr Ni Mo 17 12 2
• DIN 17006: X 2 Cr Ni Mo 17 13 2
• N° werksto 1.4404
• AFNOR: Z2 CND 17-12
• BSI: 316S11
The screws utilised are in austenitic alloy stainless
steel, corrosion and heat resistant according to the
following standards:
• ISO: 7380
• AISI: 316
• ISO quality: A4
• Resistance class ISO: from 50 to 70
External body polishing
Flange thickness (front/back): 6mm (0.24in)
External dimensions (ØxL): 154x358mm (6.1x14.1in)
Internal usable area (WxH): 88x86mm (3.5x2.9in)
(front surface dimensions), 88x86mm (3.5x3.4in) (rear
surface dimensions)
Internal usable length (with heater): 210mm (8.3in)
Cable glands: 2xPG13.5 (nickel-plated brass for
external connections) or RJ45 connector (IP67)
Gaskets: High sealing O-ring
Unit weight: 5kg (11lb)
10.3 Housing's window
Window with extra clear tempered glass
• Usable diameter: 97mm (3.8in)
• Thick: 4mm (0.16in)
10.4 Electrical
Power absorbed in input/Available power for camera
(selectable with dip-switch)
• PoE input Class 3 (13W): PoE camera Class 2 (7W)
• Hi-PoE input Class 4 (25W): PoE camera Class 3
(13W)
Data line: 10/100Base-T
Heater
• PoE input Class 3: 3W, Ton 15°C±3°C (59°F ±5°F),
To 22°C±3°C (72°F±5°F)
• Hi-PoE input Class 4: 7W, Ton 15°C±3°C (59°F
±5°F), To 22°C±3°C (72°F±5°F)
Demisting: 1W
Compatible with IEEE 802.3af, IEEE 802.3at/PoE Plus
10.5 Environment
For indoors and outdoors installation
Submersible: up to -40m (-130ft) (pressure: 4bar)
Operating temperature (with wide range cameras, in
Hi-PoE version Hi-PoE): from -20°C (-4°F) up to +60°C
(140°F)
10.6 Certications
Electrical safety (CE): EN60065
Electromagnetic compatibility (CE): EN50130-4,
EN61000-6-3
IP protection degree (EN60529): IP66, IP67, IP68, IP69
EAC certication
Instruction manual - English - EN
9MNVCNXM36POE_2021_EN
11 Technical drawings
The indicated measurements are expressed in millimetres.
B - B
B
B
A - A
A
A
184
Ø 112
164
Ø 154
75
11
460
210
43
88
86
75
88
342
346
93
358
A
A
130
115
60
80
M5
Hi-PoE BOARD
RJ45 CONNECTOR
USABLE
AREA
USABLE
AREA
USABLE AREA
FIXING BASE
Fig. 10 NXM36 Hi-PoE.
MNVCNXM36POE_2021_EN
Headquarters Italy Videotec S.p.A.
Via Friuli, 6 - I-36015 Schio (VI) - Italy
Tel. +39 0445 697411 - Fax +39 0445 697414
Email: [email protected]
France Videotec France SARL
Immeuble Le Montreal, 19bis Avenue du Québec, ZA de Courtaboeuf
91140 Villebon sur Yvette - France
Tel. +33 1 60491816 - Fax +33 1 69284736
Email: info.fr@videotec.com
Asia Pacic Videotec (HK) Ltd
Flat 8, 19/F. On Dak Industrial Building, No. 2-6 Wah Sing Street
Kwai Chung, New Territories - Hong Kong
Tel. +852 2333 0601 - Fax +852 2311 0026
Email: info.hk@videotec.com
Americas Videotec Security, Inc.
Gateway Industrial Park, 35 Gateway Drive, Suite 100
Plattsburgh, NY 12901 - U.S.A.
Tel. +1 518 825 0020 - Fax +1 518 825 0022
Email: info.usa@videotec.com
www.videotec.com
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Manuale di istruzioni - Italiano - IT
9MNVCNXM36POE_2021_IT
11 Disegni tecnici
Le misure indicate sono espresse in millimetri.
B - B
B
B
A - A
A
A
184
Ø 112
164
Ø 154
75
11
460
210
43
88
86
75
88
342
346
93
358
A
A
130
115
60
80
M5
SCHEDA Hi-PoE
CONNETTORE RJ45
AREA
UTILE
AREA
UTILE
AREA UTILE
BASE DI FISSAGGIO
Fig. 10 NXM36 Hi-PoE.
MNVCNXM36POE_2021_IT
Headquarters Italy Videotec S.p.A.
Via Friuli, 6 - I-36015 Schio (VI) - Italy
Tel. +39 0445 697411 - Fax +39 0445 697414
Email: [email protected]
France Videotec France SARL
Immeuble Le Montreal, 19bis Avenue du Québec, ZA de Courtaboeuf
91140 Villebon sur Yvette - France
Tel. +33 1 60491816 - Fax +33 1 69284736
Email: info.fr@videotec.com
Asia Pacic Videotec (HK) Ltd
Flat 8, 19/F. On Dak Industrial Building, No. 2-6 Wah Sing Street
Kwai Chung, New Territories - Hong Kong
Tel. +852 2333 0601 - Fax +852 2311 0026
Email: info.hk@videotec.com
Americas Videotec Security, Inc.
Gateway Industrial Park, 35 Gateway Drive, Suite 100
Plattsburgh, NY 12901 - U.S.A.
Tel. +1 518 825 0020 - Fax +1 518 825 0022
Email: info.usa@videotec.com
www.videotec.com
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Manuel d’instructions - Français - FR
9MNVCNXM36POE_2021_FR
11 Dessins techniques
Les tailles indiquées sont en millimètres.
B - B
B
B
A - A
A
A
184
Ø 112
164
Ø 154
75
11
460
210
43
88
86
75
88
342
346
93
358
A
A
130
115
60
80
M5
CARTE Hi-PoE
SURFACE
UTILE
SURFACE
UTILE
SURFACE UTILE
BASE DE FIXATION
CONNECTEUR
RJ45
Fig. 10 NXM36 Hi-PoE.
MNVCNXM36POE_2021_FR
Headquarters Italy Videotec S.p.A.
Via Friuli, 6 - I-36015 Schio (VI) - Italy
Tel. +39 0445 697411 - Fax +39 0445 697414
Email: [email protected]
France Videotec France SARL
Immeuble Le Montreal, 19bis Avenue du Québec, ZA de Courtaboeuf
91140 Villebon sur Yvette - France
Tel. +33 1 60491816 - Fax +33 1 69284736
Email: info.fr@videotec.com
Asia Pacic Videotec (HK) Ltd
Flat 8, 19/F. On Dak Industrial Building, No. 2-6 Wah Sing Street
Kwai Chung, New Territories - Hong Kong
Tel. +852 2333 0601 - Fax +852 2311 0026
Email: info.hk@videotec.com
Americas Videotec Security, Inc.
Gateway Industrial Park, 35 Gateway Drive, Suite 100
Plattsburgh, NY 12901 - U.S.A.
Tel. +1 518 825 0020 - Fax +1 518 825 0022
Email: info.usa@videotec.com
www.videotec.com
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
MNVCNXM36POE_2021_DE
Headquarters Italy Videotec S.p.A.
Via Friuli, 6 - I-36015 Schio (VI) - Italy
Tel. +39 0445 697411 - Fax +39 0445 697414
Email: [email protected]
France Videotec France SARL
Immeuble Le Montreal, 19bis Avenue du Québec, ZA de Courtaboeuf
91140 Villebon sur Yvette - France
Tel. +33 1 60491816 - Fax +33 1 69284736
Email: info.fr@videotec.com
Asia Pacic Videotec (HK) Ltd
Flat 8, 19/F. On Dak Industrial Building, No. 2-6 Wah Sing Street
Kwai Chung, New Territories - Hong Kong
Tel. +852 2333 0601 - Fax +852 2311 0026
Email: info.hk@videotec.com
Americas Videotec Security, Inc.
Gateway Industrial Park, 35 Gateway Drive, Suite 100
Plattsburgh, NY 12901 - U.S.A.
Tel. +1 518 825 0020 - Fax +1 518 825 0022
Email: info.usa@videotec.com
www.videotec.com
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
MNVCNXM36POE_2021_RU
Headquarters Italy Videotec S.p.A.
Via Friuli, 6 - I-36015 Schio (VI) - Italy
Tel. +39 0445 697411 - Fax +39 0445 697414
Email: [email protected]
France Videotec France SARL
Immeuble Le Montreal, 19bis Avenue du Québec, ZA de Courtaboeuf
91140 Villebon sur Yvette - France
Tel. +33 1 60491816 - Fax +33 1 69284736
Email: info.fr@videotec.com
Asia Pacic Videotec (HK) Ltd
Flat 8, 19/F. On Dak Industrial Building, No. 2-6 Wah Sing Street
Kwai Chung, New Territories - Hong Kong
Tel. +852 2333 0601 - Fax +852 2311 0026
Email: info.hk@videotec.com
Americas Videotec Security, Inc.
Gateway Industrial Park, 35 Gateway Drive, Suite 100
Plattsburgh, NY 12901 - U.S.A.
Tel. +1 518 825 0020 - Fax +1 518 825 0022
Email: info.usa@videotec.com
www.videotec.com
Page is loading ...
MNVCNXM36POE_2021
Headquarters Italy Videotec S.p.A.
Via Friuli, 6 - I-36015 Schio (VI) - Italy
Tel. +39 0445 697411 - Fax +39 0445 697414
Email: [email protected]
France Videotec France SARL
Immeuble Le Montreal, 19bis Avenue du Québec, ZA de Courtaboeuf
91140 Villebon sur Yvette - France
Tel. +33 1 60491816 - Fax +33 1 69284736
Email: info.fr@videotec.com
Asia Pacic Videotec (HK) Ltd
Flat 8, 19/F. On Dak Industrial Building, No. 2-6 Wah Sing Street
Kwai Chung, New Territories - Hong Kong
Tel. +852 2333 0601 - Fax +852 2311 0026
Email: info.hk@videotec.com
Americas Videotec Security, Inc.
Gateway Industrial Park, 35 Gateway Drive, Suite 100
Plattsburgh, NY 12901 - U.S.A.
Tel. +1 518 825 0020 - Fax +1 518 825 0022
Email: info.usa@videotec.com
MNVCNXM36POE_2021
www.videotec.com
/