Lanier D5530 User guide

Type
User guide

This manual is also suitable for

Quick Guide
Checking the Accessories
If anything is missing or damaged, contact your
sales representative or service representative.
Quick Guide (this sheet)
Read This First
Power cord
Dedicated USB cable for the touch module
HDMI cable
Pen
Eraser
Component Names and
Functions
Front/Control panel
8 8
1
7
6
3 4 5
2
Y310IA0021
10
9
8
1
8
5
2
3
4
Y310IA0022
7
6
9
10 11
RICOH Collaboration Board D5530/D5530BK
RICOH Collaboration Board D6520/D6520BK/D7510/D7510BK
No. Name Description
Control panel
This is where the buttons for operating the Collaboration Board are located.
For details about these buttons, refer to descriptions from No. 2 to 5.
Power button
Turns the machine on or off.
Lights up blue when the power is turned on. Turns off when the power is turned off.
[Menu] Opens or closes the On-Screen Display menu.
[
+]/[-
]/[
]/[
]
Scrolls through settings and options in the On-Screen Display menu.
[
+]/[-
]: Hot keys for audio volume adjustment.
[Enter/Input]
Selects a video source.
Confirms your selection or enters a submenu in the On-Screen Display menu.
Controller unit
For connecting cables, such as an Ethernet cable. For details, see reverse side of this manual. The
controller unit may not be connected to the machine, depending on the situation.
Capture box
For connecting video cables. For details, see Section 4 of this manual. The capture box may not be
connected to the machine, depending on the situation.
Magnetic pen and eraser holder For holding the pens and erasers when they are not in use.
Motion detection sensor Detects a person approaching the machine, and exits Standby mode automatically.
Remote control sensor window Receives command signals from the remote control.
Power indicator
(only for D5530/D5530BK)
Indicates the operating status of the machine:
Lights up blue when the power is turned on. -
Turns off when the power is turned off. -
For safe and correct use, be sure to read the Safety Information in "Read This First" before using the machine.
Some illustrations in this manual might be slightly different from the machine.
Connecting to input terminals of RICOH Collaboration Board
Connect cables to input terminals of RICOH Collaboration Board in
the following cases:
Using RICOH Collaboration Board as a monitor
Using the picture in picture function to display 2 screens simultaneously.
Using RICOH Interactive Whiteboard Lt for Windows
Y310IA0023
Y310IA0024
Connecting the VGA input
Y310IA0025
To output audio from the speaker, use an audio cable.
Connecting the digital input
Using the HDMI cable
Y310IA0026
Using the DisplayPort cable
Y310IA0027
Using RICOH Interactive Whiteboard Lt for Windows
Y310IA0033
To use RICOH Interactive Whiteboard Lt for Windows, an HDMI, DisplayPort,
or VGA cable is required.
To use the picture in picture function, connect the video source of the subpicture
to the input terminal of RICOH Collaboration Board.
Connection
Connecting to input terminals of the capture box
If you want to display the screen of an external device and write text
or draw figures on the displayed screen when using RICOH Interactive
Whiteboard Controller OP-10/5 or RICOH Collaboration Board
Controller Type 3, connect the external device to one of the input
terminals of the capture box.
Y310IA0031
Connecting the VGA input
Y310IA0034
Connecting the digital input
Using the HDMI cable
Y310IA0035
Using the DisplayPort cable
Y310IA0036
To use the picture in picture function, connect the video source of the main
picture to the input terminal of the capture box.
Remote control
AAA batteries x 2
VGA cable
Other documents
Before discarding the package, check that you
haven’t left any accessories inside the box.
Dispose of packaging materials wisely. You can
recycle the cardboard carton. Consider storing
the package for future transport of the machine
if possible.
Do not leave plastic bags within reach of young
children or infants.
Manuals Provided with
This Machine
The operating instructions of this machine are
provided in the following formats:
Online manuals are available on our web site
(https://www.ricoh.com/).
Printed manuals
Read This First
Quick Guide
Web page
Read This First
Operating Instructions
RICOH Interactive Whiteboard
Controller OP-10/5, RICOH
Collaboration Board Controller Type 3
You can also use the following terminals
when using RICOH Interactive Whiteboard
Controller OP-10/5, RICOH Collaboration
Board Controller Type 3.
1
2
3
4
5
Y310IA0034
1 HDMI Output
A picture can be output to Audio-visual device/
monitor device.
2 USB ports (USB 3.0 Type A)
These ports are used to connect the capture box
and accessories or to connect USB memory
devices.
3 Ethernet interface (10/100/1000 Mbps)
This interface is used to connect the machine to
a network.
4 Audio Input
5 Audio Output
Basic operations
Turning the machine on or off
To turn on or off the machine, press the pow-
er button on the control panel of the machine
or on the remote control.
DTW161
Switching input sources
Press the [INPUT] button or those
input source buttons on the remote
control or the [Enter/Input] button
on the control panel to select an
input source.
Adjusting audio volume level
Press [-
] or [
+] on the control
panel or [Volume+]/[Volume-] on
the remote control to adjust the
volume.
Connecting the external speakers
Y310IA0029
Connecting the external device using
the USB cable
This machine has multiple USB ports for
connection to external devices. For informa-
tion on how to use each USB port, refer to
the Input/Output Terminals in "Read This
First".
Using the Remote Control
Do not put the remote control in the direct heat,
humidity, and avoid re.
Do not drop the remote control, as doing so may
cause the remote control to malfunction.
Con rm there is no object between the remote
control and the remote control sensor of the
product.
When the remote control will not be used for an
extended period, remove the batteries.
DTW159
1
6
7
8
9
5
3
2
4
[Power]
Turns the machine on or off.
[INPUT]
Selects an input source.
[EXIT]
Returns to the previous menu or closes the
On-Screen Display menu when the On-Screen
Display menu is on.
[
]/[Volume-]/[
]/[Volume+]
Scrolls through settings and options in the
On-Screen Display menu.
Turns down/up the volume.
[ENTER]
Confirms your selection or save changes.
[INFO]
Shows the current input source and resolution.
Input source buttons/PIP button
Numeric buttons (1-9) perform as input source
buttons when the On-Screen Display menu is off.
Numeric button (6) turns on or off the PIP function.
[Computer In] is only available if the controller
designed compliant with OPS (Open Pluggable
Speci cation) standard is connected to this ma-
chine.
[DVI] is not available on this machine.
[MENU]
Opens or closes the On-Screen Display menu.
[
]/[
]/[Mute]
Scrolls through settings and options in the
On-Screen Display menu when the On-Screen
Display menu is on.
Turns on or off the mute function.
Remote control usage tips
Point and aim the top front of the remote
control directly at the display’s remote
control sensor window when you press
the buttons.
Do not let the remote control become wet
or place it in humid environments (like
bathrooms).
If th e display’s remote control sensor
window is exposed to direct sunlight or
strong light, the remote control may not
operate properly. In this situation, change
the light source, readjust the angle of the
display or operate the remote control
from a location closer to display’s remote
control sensor window.
Y310IA0030
Max. 7 m
(22.9 feet)
Max. 7 m
(22.9 feet)
30˚
30˚
30˚
30˚
RICOH Collaboration Board D5530/D5530BK
RICOH Collaboration Board D6520/D6520BK/D7510/D7510BK
Connecting power
The supplied power cord or cords are for use
with this machine only. They cannot be used for
appliances other than this machine. Also, do not
use power cords other than the power cord or
cords supplied with this machine. Doing so can
result in  re or electric shock.
There are dangerous voltages inside the ma-
chine. Never unscrew or remove any covers.
Turn off the power and unplug the power cord if
you intend to move the machine.
Never use a power cord which appears dam-
aged or frayed, or change the plug type on the
power cord.
Be aware of the power loading when you use
extension cords or multiple outlet power
boards.
Plug one end of the power cord into
the AC In jack on the machine and
the other end into an appropriate
power outlet.
DYS111
The power cord and outlet illustrated may differ
from the ones used in your region.
Quick Guide
© 2019 Ricoh Co., Ltd.
EN GB EN US EN AU
Y310-7510
  • Page 1 1
  • Page 2 2

Lanier D5530 User guide

Type
User guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI