Vivo STAND-TV00L Assembly Instructions

Brand: Vivo

Model: STAND-TV00L

Type: Assembly Instructions

Tabletop TV Stand

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-tv00l

SKU: STAND-TV00L

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

PACKAGE CONTENTS

WARNING!

a1 (x2)

TV Plate

a2 (x1)

TV Plate

Connector

b (x2)

Bracket

h (x2)

M6x14

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please call a qualified technician. Check carefully to make sure there are no missing or

defective parts. Improper installation may cause damage or serious injury. Do not use this product

for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.

We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED

c (x1)

Tempered

Glass Base

d1(x1)

Lower Support

Column

d2 (x1)

Upper Support

Column

e (x1)

Plastic Cover

f (x1)

Metal Pad

g (x1)

Swivel Pad

i (x3)

M6x18

j (x2)

Cable Clip

k (x4)

Rubber Foot

l (x10)

M6x10

m (x8)

Washer

n (x4)

M4x12

o (x4)

M4x30

p (x4)

M6x20

q (x4)

M6x35

r (x4)

M8x20

s (x4)

M8x45

t (x4)

M4 Washer

u1 (x4)

M6 Washer

v (x4)

M8 Washer

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV STAND.

• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

w (x4)

M4 Spacer

x (x8)

M6/8 Spacer

y (x1)

Allen Wrench

z (x1)

Security Wire Kit

A (x2)

Buckle

B (x4)

M4x6

u2 (x2)

6.5x18x2

Washer

u3 (x3)

6.5x20x1.5

Washer

C (x1)

Bubble Level

ASSEMBLY STEPS

STEP 1

TOOLS NEEDED

88lbs

(39.92kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

Phillips

Screwdriver

Stick rubber feet (k) to bottom of glass base (c). Assemble upper and lower support columns (d1, d2)

using M6x10 bolts (l) with 6.5x18x2 washers (u2), then attach support column to swivel pad (g) using

M6x14 bolts (h) and tighten with Allen wrench (y). Attach column with pad to glass base using metal

pad (f), M6x18 bolts (i) and 6.5x20x2 washers (u3), making sure the metal pad is placed between the

glass base and swivel pad, and with the tabs inserted into the swivel pad. Tighten bolts with the Allen

wrench (y) and slide plastic cover (e) onto column.

STEP 2

Attach TV plates (a1) to TV plate connector (a2) using M6x10 bolts (l) and washers (m) and tighten

with the Allen wrench. Attach TV plate to support column at desired height using M6x10 bolts (l) and

washers (m). Clip bubble level (C) onto plate to ensure the plate is level, then tighten bolts with the

Allen wrench. Attach wire clips (j) to back of support column.

STEP 3

Mount TV brackets (b) to the back of your TV using bolts (n, o, p, q, r, s) and washers (t, u1, v)

according to the size of mounting holes on your television. Make sure TV brackets are both in the

correct orientation. For curved or recessed back TVs, spacers (w, x) may be required.

t, u, v

w, x

t, u1, v

STEP 4

Hang TV with brackets on TV plate (a) as

shown in diagram.

Secure TV brackets using buckles (A) with M4x6 bolts (B) as shown. Route cables through cable

management clips (j) on back of stand.

STEP 5

OPTION A: Wood Wall

Drill 1.75” (45mm) deep holes using a 5/32” (or 3.8mm) drill bit. Secure with screws and washers.

If your TV is located near a wall as shown in Diagram 5a, then a steel wire from security wire kit (z) can

be attached for added security. Attach the two ends of the steel wire to the top two holes on the back of

your TV as shown in Diagram 5b. Attach the center loop to your wall according to wall type as shown in

Diagram 5c, 5d or 5e.

Wall

45m m

3. 8m m

STEP 5 (Continued)

OPTION B: Concrete/Brick Wall

Drill 2” (50mm) deep holes using a 5/16” (or 8mm) drill bit, and press anchors into holes. Secure with

screws and washers.

50 mm

8m m

LAST UPDATED: 03/06/2020

Open Monday - Friday 7:00am - 7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times. If any

parts are received damaged or defective, please contact us. We are happy to replace parts to

ensure you have a fully functioning product.

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

[email protected]

AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

AVG. RESOLUTION TIME (within oice hrs): < 15 M

www.vivo-us.com

Chat live with an agent!

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

309-278-5303

Vivo STAND-TV00L Assembly Instructions

Vivo STAND-TV00L Assembly Instructions

Vivo STAND-TV00L Assembly Instructions

Related papers

Other documents