2. Telos Alliance
  3. 11
11

Telos Alliance 11, Omnia.11 Quick start guide

  • Hello! I am an AI chatbot trained to assist you with the Telos Alliance 11 Quick start guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
NETWORK CONFIGURATION (CONT.) sysTEm CONFIGURATION sysTEm CONFIGURATION (CONT.) QUICK-sTART INsTAllATION GUIdE
OmNIA.11 sTEREO Fm AUdIO PROCEssOR
Items you need to supply:
• RackwithfouravailableEIArackspacesformounting
• Professionalline-levelanalogorAES/EBUdigitalaudio
sourcesonstandardXLRconnectors
• ConfiguredEthernetswitch
REQUIRED EQUIPMENT, CABLES, AND ACCESSORIES:
Thereareafewadditionalitemsrequiredforasuccessfulinstallation.Checkthelistbelowandmakesure
youhavewhatyouneed.
Included items:
• Omnia.11AudioProcessor
• ACPowercable
• Ethernetcable
• 4rackscrews
WehavemadethisOmniaSystemeasytosetupandconfigure.Thisquick-startguidewilltakeyouthroughthe
basicstepstoconfigureyournewOmnia.11tostartdeliveringcleaner,clearer,louder,andmoreconsistentsound.
Beforewegetstarted,let’smakesureyouhavewhatyouneed.
ThANK yOU FOR PURChAsING ThE OmNIA.11 sTEREO Fm
AUdIO PROCEssOR
CONTINUE TO sysTEm CONFIGURATION
Network configuration is complete. Your system is
readyforsystemconfiguration.Continuetothe“System
Configuration”instructions.
1. Once the system has rebooted, touch the “Setup”
button(S).
2. Touch the Livewire button (T). The Livewire
configurationscreenwillbedisplayed(U).
3. If you do not have a Livewire system, make sure
the 2 Livewire output channels are disabled. The
2 "Enable" buttons (V) will be white if Livewire
is disabled and green when enabled. To disable
Livewire, touch each of the two green "Enable"
buttons(V)toturnthemwhite.
4. If you do have a Livewire system, enable Livewire
bytouchingeachofthetwo"Enable"buttons(V)to
turnthemgreen.
5. IfyouhaveaLivewiresystem,touchthewhitefields
(W) next to the Output #1 and #2 and enter the
appropriatechannelvalueviathepop-upkeyboard(X).
6. Touchthe“APPLY”button(Y)undertheOutputs.
7. Touchthewhitefields(Z)nexttotheInput#1and#2
toentertheappropriatechannelvalueviathepop-
upkeyboard(X).
8. Touchthe“APPLY”buttonundertheInputs(AA).
lIVEWIRE CONFIGURATION
OUTPUT CONFIGURATION
1. Touchthe“Output”icon(II).TheOutputConfigurationscreenwillbedisplayed.Ifthe“Basic”tabisnot
active,touchtoselectit.
INPUT CONFIGURATION
1. Touchthe“ADJ”icon(BB)toreturntotheinitialSystemscreen.
2. Touchthe“Input”icon(CC).TheInputConfigurationscreenwillbedisplayed.Ifthe“Basic”tab(DD)
isnotactive,touchtoselectit.
3. Fromthe“InputSource”drop-down(EE),selecttheAnalog,AES/EBUorLivewireinputasappropriate
foryourinstallation.Ifyouraudiosourceisprovidinganaudiofeedyoushouldseemeteractivityon
thebargraphmeters(FF).
4. Whiledrivingtheinputswithtypicalprogrammaterialatnormaloperatinglevel,adjustthe
appropriate“Master”InputGaincontrol(GG)foryourinstallationuntilthepeak-readinginputbar
graphmetersarereadingjust“intotheyellow”(about–15to–12dBFSorso).Iftheleft/rightaudio
levelscomingintotheOmnia.11aresomewhatunbalanced,youcanadjustthe“RightTrim”control
(HH)tochangetheleveloftherightchannelaloneoveralimitedrange.
©
2016TLSCorp.,AllRightsReserved.
1490-00099-001—QUICKSTARTGUIDE:OMNIA.11C16/15035
yOUR sETUP Is COmPlETE!
That’sit!YouarenowreadytoexperiencetheOmnia.11
forsoundlikeneverbefore.
1. Touchthe“FMOptions”button(JJ)ontheleftsideofthe
MenuAreaandensurethatthePre-Emphasis,Diversity
Delay(ifpresent)andBS-412settings arecorrectfor
yoursystemandyourlocation.
2. Touch the appropriate button (KK) above the “FM
Options”buttontoselectthegroupofoutputcontrols
fortheoutputyouwillbeusing.Alloutputsareactive
simultaneously. Note: If you are using a conventional
AES/EBU L/R digital output to feed an FM exciter or
linearSTL,touchthe“AES/EBU”buttonandbesurethe
“OutputSelection”issetto“FM”andthe“De-emphasis”
isturned“OFF”fortheoutputbeingused.Foraccessto
thecompositeMPXstereogeneratoroutputleveland
stereo pilot controls, touch the “Composite” button.
Note that these controls simultaneously adjust the
OmniaDirectoutput levelsaswell.Finally,adjust the
appropriatecontrolsothatthepeakoutput/modulation
level is correct for the equipment that follows the
Omnia.11.
3. Touchthe“FM”iconbutton(LL)atthetopofthescreen
andthentouchthe“Preset”tab(MM)todisplaythelist
offactoryprocessingpresets.Ifthepresetlistislocked
(grayed-out),touchthe“padlock”icontounlockit.Once
unlocked,simplytouchthedesiredpresetnameinthe
listanditwillbeputdirectly“ontheair".Werecommend
listening to all factory presets to get a feel for their
differencesandthenselectonetostartwith.
4. Touch the “Quick Setup” tab (NN) and adjust the
followingcontrolstosetthebasicloudness,bassand
brightnesssounddesired.
5. Adjust the “Clipper Drive” control (OO) as low as
possible for the loudness needed. This controls the
primaryloudnessvs.distortiontradeoff.Turningitup
makes the sound louder (but more distorted) while
turning it down makes the sound cleaner but not as
loud.Itshouldalwaysbesetaslowaspossibleforthe
levelofloudnessrequired.
6. Settheoverallamountofbassusingthe“Bass”control
(PP). At higher settings of the “Bass Thump” (QQ)
control,the “kick” or “Thump”actionofbassmaterial
isemphasized.
7. Set the basic brightness of a preset by using the
“Presence” (RR), “Treble” (SS) and “Sparkle” (TT)
controls.Notethatthesethreecontrolsonlyboostthe
brightness.Asettingof“0.0”is“flat”ortheminimum
amount of boost for the particular preset that is
currently selected. Reducing brightness can be done,
foroneexample,by reducingthehigherbandsofthe
AGCorLimitermixers.
T
S
U
Z
AA
VW
Y
X
II
KK
JJ
LL
MM
BB
CC
DD
GG
HH
EE
FF
NN
OO
PP
RR
QQ
SS TT
G
F
H
PhysICAl INsTAllATION
1. Locatethereleasepin(A)ontheinsidetopofeachhandleontheOmnia.11.
2. Slide and holdthereleasepins(A)outwardsandthenpullthehandles(B)towardsyouuntilyouhearaclick.
Makesureeachhandleissecurelylockedintotheforwardposition.
3. Usingthehandles(B), lift and slidetheOmnia.11intotheequipmentrackandsecurewithall4rackscrews.
4. Onceinstalledintotherack,locatethereleasepin(A)ontheinsidetopofeachhandle,slidethepintoward
youandfoldthehandles(B)backtotheirnormalposition.
AUdIO CONFIGURATION
AUdIO CONNECTIONs
1. Determinetheinputsandoutputsthatareappropriateforyourinstallationandfollowthe
appropriateinstructions.
AUDIO INPUT - Both analog and digital input sources may be connected simultaneously,
however, only the input source that has been selected in the Input menu will be active.
Input source selection will be covered later in this guide.
a. ForAnalogaudio,connectXLRaudiocablestotheleftandrightANALOGINPUTS(C)jacks.
b. ForDigitalaudio,connectXLRaudiocablestotheAESINPUT(D)jack.
c. ForanexistingLivewiresystem,thesingleLivewireEthernetconnectionisallthatisneededforaudioI/O
(exceptforthecompositeMPXoutputs).IMPORTANT: Do not connect an Ethernet cable at this time.
CONTINUE TO NETWORK CONFIGURATION
Youraudioconnectionsarecomplete.Continuetothe”NetworkConfiguration”instructions.
CONTINUE TO AUdIO CONFIGURATION
Yourphysicalinstallationiscomplete.Continuetothe”AudioConfiguration”instructions.
AUDIO OUTPUT - All outputs are active simultaneously.
a. ForAnalogaudio,connectXLRaudiocablestotheleftandrightANALOGOUTPUTSjacks(F).
b. ForDigitalaudio,connectXLRaudiocablestotheAESOUT1/2jacks(G).
c. ForadirectcompositeMPXconnection,connectanXLRcabletotheAESCOMPOSITEOUTjack(H).
Note:IfyouwillbeusingconventionalAES/EBUL/RdigitalaudiotofeedyourSTLorFMexciter,besure
anypre-emphasisandlimiters(ifpresent)arefullydefeatedintheexciter.TheOmniamustbetheonly
deviceprovidingthepre-emphasissoitsownde-emphasisontheAES/EBUoutputbeingusedmust
alsobe“Off”.AlsonotethatiftheSTLusesacodec(isnotlinear),theOmniamustbelocatedatthe
transmittersiteforbestperformanceandsoundquality.
d. ForanexistingLivewiresystem,thesingleLivewireEthernetconnectionisallthatisneededforaudioI/O
(exceptforthecompositeMPXoutputs).IMPORTANT: Do not connect an Ethernet cable at this time.
NETWORK CONFIGURATION
INsTAllATION hElP
Formore details abouttheOmnia.11,or to download thefullmanual
pleasevisithttps://www.telosalliance.com/Omnia/Omnia11
Ifyouhavemorequestions,calltheTelosAlliance24/7SupportTeamat
+1 (216) 622-0247,oremailusat[email protected],we’dbe
happytohelpyouout.
1. Touch the “Setup” button (L). The Network
configurationscreenwillbedisplayed(M).
2. Touchthewhitefield(N)totherightofIPAddress
labeltoenterastaticIPaddress.Note:TheOmnia.11
requires2freestaticIPaddressesonyournetwork
(DHCP is not supported), the one that you enter
andtheonedirectlyabovetheonethatyouenter.
Forexample,if you enter 192.168.0.125 as the IP
Address,bothitand192.168.0.126needtobeopen
onthenetwork.
3. Theon-screenkeyboardwillpopup(O).Touchthe
“0-9*/=” button to shift the keyboard to number
entrymode.
4. Touch the backspace key to delete the current
informationdigitbydigit,thenenteryourdesiredIP
addressfromthekeyboard.
5. TouchOK(Q)andthekeyboardwillnolongerdisplay.
6. IfyournetworkrequireschangestoSubnetMaskor
Gatewayvalues,touchthewhitefieldstotheright
ofthoselabelstochangethevaluesviathepop-up
keyboard.
7. Once your values have been entered, touch the
“APPLY” button (R). The system will display an
option to either "Reboot Now" or Reboot Later".
Touch“RebootNow”torebootthesystemandapply
thenewparameters.
NETWORK PARAmETER sETUP
2. MakesurethatnocablesarepluggedintoeitherEthernetport.
3. ConnecttheOmnia.11toACMains(I).
4. Oncethesystemhasbootedupcompletely,connectoneendoftheEthernetcabletothetopLivewire/100BT
port(J)onthebackoftheOmnia.11.ConnecttheotherendoftheEthernetcabletoaconfiguredEthernet
switch(K)toallowaccesstothenetwork.
RACK mOUNTING
AUdIO CONFIGURATION (CONT.)
A
A
A
A
B
B
D
C
L
M
N
R
O
P Q
G
F
H
PhysICAl INsTAllATION
1. Locatethereleasepin(A)ontheinsidetopofeachhandleontheOmnia.11.
2. Slide and holdthereleasepins(A)outwardsandthenpullthehandles(B)towardsyouuntilyouhearaclick.
Makesureeachhandleissecurelylockedintotheforwardposition.
3. Usingthehandles(B), lift and slidetheOmnia.11intotheequipmentrackandsecurewithall4rackscrews.
4. Onceinstalledintotherack,locatethereleasepin(A)ontheinsidetopofeachhandle,slidethepintoward
youandfoldthehandles(B)backtotheirnormalposition.
AUdIO CONFIGURATION
AUdIO CONNECTIONs
1. Determinetheinputsandoutputsthatareappropriateforyourinstallationandfollowthe
appropriateinstructions.
AUDIO INPUT - Both analog and digital input sources may be connected simultaneously,
however, only the input source that has been selected in the Input menu will be active.
Input source selection will be covered later in this guide.
a. ForAnalogaudio,connectXLRaudiocablestotheleftandrightANALOGINPUTS(C)jacks.
b. ForDigitalaudio,connectXLRaudiocablestotheAESINPUT(D)jack.
c. ForanexistingLivewiresystem,thesingleLivewireEthernetconnectionisallthatisneededforaudioI/O
(exceptforthecompositeMPXoutputs).IMPORTANT: Do not connect an Ethernet cable at this time.
CONTINUE TO NETWORK CONFIGURATION
Youraudioconnectionsarecomplete.Continuetothe”NetworkConfiguration”instructions.
CONTINUE TO AUdIO CONFIGURATION
Yourphysicalinstallationiscomplete.Continuetothe”AudioConfiguration”instructions.
AUDIO OUTPUT - All outputs are active simultaneously.
a. ForAnalogaudio,connectXLRaudiocablestotheleftandrightANALOGOUTPUTSjacks(F).
b. ForDigitalaudio,connectXLRaudiocablestotheAESOUT1/2jacks(G).
c. ForadirectcompositeMPXconnection,connectanXLRcabletotheAESCOMPOSITEOUTjack(H).
Note:IfyouwillbeusingconventionalAES/EBUL/RdigitalaudiotofeedyourSTLorFMexciter,besure
anypre-emphasisandlimiters(ifpresent)arefullydefeatedintheexciter.TheOmniamustbetheonly
deviceprovidingthepre-emphasissoitsownde-emphasisontheAES/EBUoutputbeingusedmust
alsobe“Off”.AlsonotethatiftheSTLusesacodec(isnotlinear),theOmniamustbelocatedatthe
transmittersiteforbestperformanceandsoundquality.
d. ForanexistingLivewiresystem,thesingleLivewireEthernetconnectionisallthatisneededforaudioI/O
(exceptforthecompositeMPXoutputs).IMPORTANT: Do not connect an Ethernet cable at this time.
NETWORK CONFIGURATION
INsTAllATION hElP
Formore details abouttheOmnia.11,or to download thefullmanual
pleasevisithttps://www.telosalliance.com/Omnia/Omnia11
Ifyouhavemorequestions,calltheTelosAlliance24/7SupportTeamat
+1 (216) 622-0247,oremailusat[email protected],we’dbe
happytohelpyouout.
1. Touch the “Setup” button (L). The Network
configurationscreenwillbedisplayed(M).
2. Touchthewhitefield(N)totherightofIPAddress
labeltoenterastaticIPaddress.Note:TheOmnia.11
requires2freestaticIPaddressesonyournetwork
(DHCP is not supported), the one that you enter
andtheonedirectlyabovetheonethatyouenter.
Forexample,if you enter 192.168.0.125 as the IP
Address,bothitand192.168.0.126needtobeopen
onthenetwork.
3. Theon-screenkeyboardwillpopup(O).Touchthe
“0-9*/=” button to shift the keyboard to number
entrymode.
4. Touch the backspace key to delete the current
informationdigitbydigit,thenenteryourdesiredIP
addressfromthekeyboard.
5. TouchOK(Q)andthekeyboardwillnolongerdisplay.
6. IfyournetworkrequireschangestoSubnetMaskor
Gatewayvalues,touchthewhitefieldstotheright
ofthoselabelstochangethevaluesviathepop-up
keyboard.
7. Once your values have been entered, touch the
“APPLY” button (R). The system will display an
option to either "Reboot Now" or Reboot Later".
Touch“RebootNow”torebootthesystemandapply
thenewparameters.
NETWORK PARAmETER sETUP
2. MakesurethatnocablesarepluggedintoeitherEthernetport.
3. ConnecttheOmnia.11toACMains(I).
4. Oncethesystemhasbootedupcompletely,connectoneendoftheEthernetcabletothetopLivewire/100BT
port(J)onthebackoftheOmnia.11.ConnecttheotherendoftheEthernetcabletoaconfiguredEthernet
switch(K)toallowaccesstothenetwork.
RACK mOUNTING
AUdIO CONFIGURATION (CONT.)
A
A
A
A
B
B
D
C
L
M
N
R
O
P Q
G
F
H
PhysICAl INsTAllATION
1. Locatethereleasepin(A)ontheinsidetopofeachhandleontheOmnia.11.
2. Slide and holdthereleasepins(A)outwardsandthenpullthehandles(B)towardsyouuntilyouhearaclick.
Makesureeachhandleissecurelylockedintotheforwardposition.
3. Usingthehandles(B), lift and slidetheOmnia.11intotheequipmentrackandsecurewithall4rackscrews.
4. Onceinstalledintotherack,locatethereleasepin(A)ontheinsidetopofeachhandle,slidethepintoward
youandfoldthehandles(B)backtotheirnormalposition.
AUdIO CONFIGURATION
AUdIO CONNECTIONs
1. Determinetheinputsandoutputsthatareappropriateforyourinstallationandfollowthe
appropriateinstructions.
AUDIO INPUT - Both analog and digital input sources may be connected simultaneously,
however, only the input source that has been selected in the Input menu will be active.
Input source selection will be covered later in this guide.
a. ForAnalogaudio,connectXLRaudiocablestotheleftandrightANALOGINPUTS(C)jacks.
b. ForDigitalaudio,connectXLRaudiocablestotheAESINPUT(D)jack.
c. ForanexistingLivewiresystem,thesingleLivewireEthernetconnectionisallthatisneededforaudioI/O
(exceptforthecompositeMPXoutputs).IMPORTANT: Do not connect an Ethernet cable at this time.
CONTINUE TO NETWORK CONFIGURATION
Youraudioconnectionsarecomplete.Continuetothe”NetworkConfiguration”instructions.
CONTINUE TO AUdIO CONFIGURATION
Yourphysicalinstallationiscomplete.Continuetothe”AudioConfiguration”instructions.
AUDIO OUTPUT - All outputs are active simultaneously.
a. ForAnalogaudio,connectXLRaudiocablestotheleftandrightANALOGOUTPUTSjacks(F).
b. ForDigitalaudio,connectXLRaudiocablestotheAESOUT1/2jacks(G).
c. ForadirectcompositeMPXconnection,connectanXLRcabletotheAESCOMPOSITEOUTjack(H).
Note:IfyouwillbeusingconventionalAES/EBUL/RdigitalaudiotofeedyourSTLorFMexciter,besure
anypre-emphasisandlimiters(ifpresent)arefullydefeatedintheexciter.TheOmniamustbetheonly
deviceprovidingthepre-emphasissoitsownde-emphasisontheAES/EBUoutputbeingusedmust
alsobe“Off”.AlsonotethatiftheSTLusesacodec(isnotlinear),theOmniamustbelocatedatthe
transmittersiteforbestperformanceandsoundquality.
d. ForanexistingLivewiresystem,thesingleLivewireEthernetconnectionisallthatisneededforaudioI/O
(exceptforthecompositeMPXoutputs).IMPORTANT: Do not connect an Ethernet cable at this time.
NETWORK CONFIGURATION
INsTAllATION hElP
Formore details abouttheOmnia.11,or to download thefullmanual
pleasevisithttps://www.telosalliance.com/Omnia/Omnia11
Ifyouhavemorequestions,calltheTelosAlliance24/7SupportTeamat
+1 (216) 622-0247,oremailusat[email protected],we’dbe
happytohelpyouout.
1. Touch the “Setup” button (L). The Network
configurationscreenwillbedisplayed(M).
2. Touchthewhitefield(N)totherightofIPAddress
labeltoenterastaticIPaddress.Note:TheOmnia.11
requires2freestaticIPaddressesonyournetwork
(DHCP is not supported), the one that you enter
andtheonedirectlyabovetheonethatyouenter.
Forexample,if you enter 192.168.0.125 as the IP
Address,bothitand192.168.0.126needtobeopen
onthenetwork.
3. Theon-screenkeyboardwillpopup(O).Touchthe
“0-9*/=” button to shift the keyboard to number
entrymode.
4. Touch the backspace key to delete the current
informationdigitbydigit,thenenteryourdesiredIP
addressfromthekeyboard.
5. TouchOK(Q)andthekeyboardwillnolongerdisplay.
6. IfyournetworkrequireschangestoSubnetMaskor
Gatewayvalues,touchthewhitefieldstotheright
ofthoselabelstochangethevaluesviathepop-up
keyboard.
7. Once your values have been entered, touch the
“APPLY” button (R). The system will display an
option to either "Reboot Now" or Reboot Later".
Touch“RebootNow”torebootthesystemandapply
thenewparameters.
NETWORK PARAmETER sETUP
2. MakesurethatnocablesarepluggedintoeitherEthernetport.
3. ConnecttheOmnia.11toACMains(I).
4. Oncethesystemhasbootedupcompletely,connectoneendoftheEthernetcabletothetopLivewire/100BT
port(J)onthebackoftheOmnia.11.ConnecttheotherendoftheEthernetcabletoaconfiguredEthernet
switch(K)toallowaccesstothenetwork.
RACK mOUNTING
AUdIO CONFIGURATION (CONT.)
A
A
A
A
B
B
D
C
L
M
N
R
O
P Q
G
F
H
PhysICAl INsTAllATION
1. Locatethereleasepin(A)ontheinsidetopofeachhandleontheOmnia.11.
2. Slide and holdthereleasepins(A)outwardsandthenpullthehandles(B)towardsyouuntilyouhearaclick.
Makesureeachhandleissecurelylockedintotheforwardposition.
3. Usingthehandles(B), lift and slidetheOmnia.11intotheequipmentrackandsecurewithall4rackscrews.
4. Onceinstalledintotherack,locatethereleasepin(A)ontheinsidetopofeachhandle,slidethepintoward
youandfoldthehandles(B)backtotheirnormalposition.
AUdIO CONFIGURATION
AUdIO CONNECTIONs
1. Determinetheinputsandoutputsthatareappropriateforyourinstallationandfollowthe
appropriateinstructions.
AUDIO INPUT - Both analog and digital input sources may be connected simultaneously,
however, only the input source that has been selected in the Input menu will be active.
Input source selection will be covered later in this guide.
a. ForAnalogaudio,connectXLRaudiocablestotheleftandrightANALOGINPUTS(C)jacks.
b. ForDigitalaudio,connectXLRaudiocablestotheAESINPUT(D)jack.
c. ForanexistingLivewiresystem,thesingleLivewireEthernetconnectionisallthatisneededforaudioI/O
(exceptforthecompositeMPXoutputs).IMPORTANT: Do not connect an Ethernet cable at this time.
CONTINUE TO NETWORK CONFIGURATION
Youraudioconnectionsarecomplete.Continuetothe”NetworkConfiguration”instructions.
CONTINUE TO AUdIO CONFIGURATION
Yourphysicalinstallationiscomplete.Continuetothe”AudioConfiguration”instructions.
AUDIO OUTPUT - All outputs are active simultaneously.
a. ForAnalogaudio,connectXLRaudiocablestotheleftandrightANALOGOUTPUTSjacks(F).
b. ForDigitalaudio,connectXLRaudiocablestotheAESOUT1/2jacks(G).
c. ForadirectcompositeMPXconnection,connectanXLRcabletotheAESCOMPOSITEOUTjack(H).
Note:IfyouwillbeusingconventionalAES/EBUL/RdigitalaudiotofeedyourSTLorFMexciter,besure
anypre-emphasisandlimiters(ifpresent)arefullydefeatedintheexciter.TheOmniamustbetheonly
deviceprovidingthepre-emphasissoitsownde-emphasisontheAES/EBUoutputbeingusedmust
alsobe“Off”.AlsonotethatiftheSTLusesacodec(isnotlinear),theOmniamustbelocatedatthe
transmittersiteforbestperformanceandsoundquality.
d. ForanexistingLivewiresystem,thesingleLivewireEthernetconnectionisallthatisneededforaudioI/O
(exceptforthecompositeMPXoutputs).IMPORTANT: Do not connect an Ethernet cable at this time.
NETWORK CONFIGURATION
INsTAllATION hElP
Formore details abouttheOmnia.11,or to download thefullmanual
pleasevisithttps://www.telosalliance.com/Omnia/Omnia11
Ifyouhavemorequestions,calltheTelosAlliance24/7SupportTeamat
+1 (216) 622-0247,oremailusat[email protected],we’dbe
happytohelpyouout.
1. Touch the “Setup” button (L). The Network
configurationscreenwillbedisplayed(M).
2. Touchthewhitefield(N)totherightofIPAddress
labeltoenterastaticIPaddress.Note:TheOmnia.11
requires2freestaticIPaddressesonyournetwork
(DHCP is not supported), the one that you enter
andtheonedirectlyabovetheonethatyouenter.
Forexample,if you enter 192.168.0.125 as the IP
Address,bothitand192.168.0.126needtobeopen
onthenetwork.
3. Theon-screenkeyboardwillpopup(O).Touchthe
“0-9*/=” button to shift the keyboard to number
entrymode.
4. Touch the backspace key to delete the current
informationdigitbydigit,thenenteryourdesiredIP
addressfromthekeyboard.
5. TouchOK(Q)andthekeyboardwillnolongerdisplay.
6. IfyournetworkrequireschangestoSubnetMaskor
Gatewayvalues,touchthewhitefieldstotheright
ofthoselabelstochangethevaluesviathepop-up
keyboard.
7. Once your values have been entered, touch the
“APPLY” button (R). The system will display an
option to either "Reboot Now" or Reboot Later".
Touch“RebootNow”torebootthesystemandapply
thenewparameters.
NETWORK PARAmETER sETUP
2. MakesurethatnocablesarepluggedintoeitherEthernetport.
3. ConnecttheOmnia.11toACMains(I).
4. Oncethesystemhasbootedupcompletely,connectoneendoftheEthernetcabletothetopLivewire/100BT
port(J)onthebackoftheOmnia.11.ConnecttheotherendoftheEthernetcabletoaconfiguredEthernet
switch(K)toallowaccesstothenetwork.
RACK mOUNTING
AUdIO CONFIGURATION (CONT.)
A
A
A
A
B
B
D
C
L
M
N
R
O
P Q
NETWORK CONFIGURATION (CONT.) sysTEm CONFIGURATION sysTEm CONFIGURATION (CONT.) QUICK-sTART INsTAllATION GUIdE
OmNIA.11 sTEREO Fm AUdIO PROCEssOR
Items you need to supply:
• RackwithfouravailableEIArackspacesformounting
• Professionalline-levelanalogorAES/EBUdigitalaudio
sourcesonstandardXLRconnectors
• ConfiguredEthernetswitch
REQUIRED EQUIPMENT, CABLES, AND ACCESSORIES:
Thereareafewadditionalitemsrequiredforasuccessfulinstallation.Checkthelistbelowandmakesure
youhavewhatyouneed.
Included items:
• Omnia.11AudioProcessor
• ACPowercable
• Ethernetcable
• 4rackscrews
WehavemadethisOmniaSystemeasytosetupandconfigure.Thisquick-startguidewilltakeyouthroughthe
basicstepstoconfigureyournewOmnia.11tostartdeliveringcleaner,clearer,louder,andmoreconsistentsound.
Beforewegetstarted,let’smakesureyouhavewhatyouneed.
ThANK yOU FOR PURChAsING ThE OmNIA.11 sTEREO Fm
AUdIO PROCEssOR
CONTINUE TO sysTEm CONFIGURATION
Network configuration is complete. Your system is
readyforsystemconfiguration.Continuetothe“System
Configuration”instructions.
1. Once the system has rebooted, touch the “Setup”
button(S).
2. Touch the Livewire button (T). The Livewire
configurationscreenwillbedisplayed(U).
3. If you do not have a Livewire system, make sure
the 2 Livewire output channels are disabled. The
2 "Enable" buttons (V) will be white if Livewire
is disabled and green when enabled. To disable
Livewire, touch each of the two green "Enable"
buttons(V)toturnthemwhite.
4. If you do have a Livewire system, enable Livewire
bytouchingeachofthetwo"Enable"buttons(V)to
turnthemgreen.
5. IfyouhaveaLivewiresystem,touchthewhitefields
(W) next to the Output #1 and #2 and enter the
appropriatechannelvalueviathepop-upkeyboard(X).
6. Touchthe“APPLY”button(Y)undertheOutputs.
7. Touchthewhitefields(Z)nexttotheInput#1and#2
toentertheappropriatechannelvalueviathepop-
upkeyboard(X).
8. Touchthe“APPLY”buttonundertheInputs(AA).
lIVEWIRE CONFIGURATION
OUTPUT CONFIGURATION
1. Touchthe“Output”icon(II).TheOutputConfigurationscreenwillbedisplayed.Ifthe“Basic”tabisnot
active,touchtoselectit.
INPUT CONFIGURATION
1. Touchthe“ADJ”icon(BB)toreturntotheinitialSystemscreen.
2. Touchthe“Input”icon(CC).TheInputConfigurationscreenwillbedisplayed.Ifthe“Basic”tab(DD)
isnotactive,touchtoselectit.
3. Fromthe“InputSource”drop-down(EE),selecttheAnalog,AES/EBUorLivewireinputasappropriate
foryourinstallation.Ifyouraudiosourceisprovidinganaudiofeedyoushouldseemeteractivityon
thebargraphmeters(FF).
4. Whiledrivingtheinputswithtypicalprogrammaterialatnormaloperatinglevel,adjustthe
appropriate“Master”InputGaincontrol(GG)foryourinstallationuntilthepeak-readinginputbar
graphmetersarereadingjust“intotheyellow”(about–15to–12dBFSorso).Iftheleft/rightaudio
levelscomingintotheOmnia.11aresomewhatunbalanced,youcanadjustthe“RightTrim”control
(HH)tochangetheleveloftherightchannelaloneoveralimitedrange.
©
2016TLSCorp.,AllRightsReserved.
1490-00099-001—QUICKSTARTGUIDE:OMNIA.11C16/15035
yOUR sETUP Is COmPlETE!
That’sit!YouarenowreadytoexperiencetheOmnia.11
forsoundlikeneverbefore.
1. Touchthe“FMOptions”button(JJ)ontheleftsideofthe
MenuAreaandensurethatthePre-Emphasis,Diversity
Delay(ifpresent)andBS-412settings arecorrectfor
yoursystemandyourlocation.
2. Touch the appropriate button (KK) above the “FM
Options”buttontoselectthegroupofoutputcontrols
fortheoutputyouwillbeusing.Alloutputsareactive
simultaneously. Note: If you are using a conventional
AES/EBU L/R digital output to feed an FM exciter or
linearSTL,touchthe“AES/EBU”buttonandbesurethe
“OutputSelection”issetto“FM”andthe“De-emphasis”
isturned“OFF”fortheoutputbeingused.Foraccessto
thecompositeMPXstereogeneratoroutputleveland
stereo pilot controls, touch the “Composite” button.
Note that these controls simultaneously adjust the
OmniaDirectoutput levelsaswell.Finally,adjust the
appropriatecontrolsothatthepeakoutput/modulation
level is correct for the equipment that follows the
Omnia.11.
3. Touchthe“FM”iconbutton(LL)atthetopofthescreen
andthentouchthe“Preset”tab(MM)todisplaythelist
offactoryprocessingpresets.Ifthepresetlistislocked
(grayed-out),touchthe“padlock”icontounlockit.Once
unlocked,simplytouchthedesiredpresetnameinthe
listanditwillbeputdirectly“ontheair".Werecommend
listening to all factory presets to get a feel for their
differencesandthenselectonetostartwith.
4. Touch the “Quick Setup” tab (NN) and adjust the
followingcontrolstosetthebasicloudness,bassand
brightnesssounddesired.
5. Adjust the “Clipper Drive” control (OO) as low as
possible for the loudness needed. This controls the
primaryloudnessvs.distortiontradeoff.Turningitup
makes the sound louder (but more distorted) while
turning it down makes the sound cleaner but not as
loud.Itshouldalwaysbesetaslowaspossibleforthe
levelofloudnessrequired.
6. Settheoverallamountofbassusingthe“Bass”control
(PP). At higher settings of the “Bass Thump” (QQ)
control,the “kick” or “Thump”actionofbassmaterial
isemphasized.
7. Set the basic brightness of a preset by using the
“Presence” (RR), “Treble” (SS) and “Sparkle” (TT)
controls.Notethatthesethreecontrolsonlyboostthe
brightness.Asettingof“0.0”is“flat”ortheminimum
amount of boost for the particular preset that is
currently selected. Reducing brightness can be done,
foroneexample,by reducingthehigherbandsofthe
AGCorLimitermixers.
T
S
U
Z
AA
VW
Y
X
II
KK
JJ
LL
MM
BB
CC
DD
GG
HH
EE
FF
NN
OO
PP
RR
QQ
SS TT
NETWORK CONFIGURATION (CONT.) sysTEm CONFIGURATION sysTEm CONFIGURATION (CONT.) QUICK-sTART INsTAllATION GUIdE
OmNIA.11 sTEREO Fm AUdIO PROCEssOR
Items you need to supply:
• RackwithfouravailableEIArackspacesformounting
• Professionalline-levelanalogorAES/EBUdigitalaudio
sourcesonstandardXLRconnectors
• ConfiguredEthernetswitch
REQUIRED EQUIPMENT, CABLES, AND ACCESSORIES:
Thereareafewadditionalitemsrequiredforasuccessfulinstallation.Checkthelistbelowandmakesure
youhavewhatyouneed.
Included items:
• Omnia.11AudioProcessor
• ACPowercable
• Ethernetcable
• 4rackscrews
WehavemadethisOmniaSystemeasytosetupandconfigure.Thisquick-startguidewilltakeyouthroughthe
basicstepstoconfigureyournewOmnia.11tostartdeliveringcleaner,clearer,louder,andmoreconsistentsound.
Beforewegetstarted,let’smakesureyouhavewhatyouneed.
ThANK yOU FOR PURChAsING ThE OmNIA.11 sTEREO Fm
AUdIO PROCEssOR
CONTINUE TO sysTEm CONFIGURATION
Network configuration is complete. Your system is
readyforsystemconfiguration.Continuetothe“System
Configuration”instructions.
1. Once the system has rebooted, touch the “Setup”
button(S).
2. Touch the Livewire button (T). The Livewire
configurationscreenwillbedisplayed(U).
3. If you do not have a Livewire system, make sure
the 2 Livewire output channels are disabled. The
2 "Enable" buttons (V) will be white if Livewire
is disabled and green when enabled. To disable
Livewire, touch each of the two green "Enable"
buttons(V)toturnthemwhite.
4. If you do have a Livewire system, enable Livewire
bytouchingeachofthetwo"Enable"buttons(V)to
turnthemgreen.
5. IfyouhaveaLivewiresystem,touchthewhitefields
(W) next to the Output #1 and #2 and enter the
appropriatechannelvalueviathepop-upkeyboard(X).
6. Touchthe“APPLY”button(Y)undertheOutputs.
7. Touchthewhitefields(Z)nexttotheInput#1and#2
toentertheappropriatechannelvalueviathepop-
upkeyboard(X).
8. Touchthe“APPLY”buttonundertheInputs(AA).
lIVEWIRE CONFIGURATION
OUTPUT CONFIGURATION
1. Touchthe“Output”icon(II).TheOutputConfigurationscreenwillbedisplayed.Ifthe“Basic”tabisnot
active,touchtoselectit.
INPUT CONFIGURATION
1. Touchthe“ADJ”icon(BB)toreturntotheinitialSystemscreen.
2. Touchthe“Input”icon(CC).TheInputConfigurationscreenwillbedisplayed.Ifthe“Basic”tab(DD)
isnotactive,touchtoselectit.
3. Fromthe“InputSource”drop-down(EE),selecttheAnalog,AES/EBUorLivewireinputasappropriate
foryourinstallation.Ifyouraudiosourceisprovidinganaudiofeedyoushouldseemeteractivityon
thebargraphmeters(FF).
4. Whiledrivingtheinputswithtypicalprogrammaterialatnormaloperatinglevel,adjustthe
appropriate“Master”InputGaincontrol(GG)foryourinstallationuntilthepeak-readinginputbar
graphmetersarereadingjust“intotheyellow”(about–15to–12dBFSorso).Iftheleft/rightaudio
levelscomingintotheOmnia.11aresomewhatunbalanced,youcanadjustthe“RightTrim”control
(HH)tochangetheleveloftherightchannelaloneoveralimitedrange.
©
2016TLSCorp.,AllRightsReserved.
1490-00099-001—QUICKSTARTGUIDE:OMNIA.11C16/15035
yOUR sETUP Is COmPlETE!
That’sit!YouarenowreadytoexperiencetheOmnia.11
forsoundlikeneverbefore.
1. Touchthe“FMOptions”button(JJ)ontheleftsideofthe
MenuAreaandensurethatthePre-Emphasis,Diversity
Delay(ifpresent)andBS-412settings arecorrectfor
yoursystemandyourlocation.
2. Touch the appropriate button (KK) above the “FM
Options”buttontoselectthegroupofoutputcontrols
fortheoutputyouwillbeusing.Alloutputsareactive
simultaneously. Note: If you are using a conventional
AES/EBU L/R digital output to feed an FM exciter or
linearSTL,touchthe“AES/EBU”buttonandbesurethe
“OutputSelection”issetto“FM”andthe“De-emphasis”
isturned“OFF”fortheoutputbeingused.Foraccessto
thecompositeMPXstereogeneratoroutputleveland
stereo pilot controls, touch the “Composite” button.
Note that these controls simultaneously adjust the
OmniaDirectoutput levelsaswell.Finally,adjust the
appropriatecontrolsothatthepeakoutput/modulation
level is correct for the equipment that follows the
Omnia.11.
3. Touchthe“FM”iconbutton(LL)atthetopofthescreen
andthentouchthe“Preset”tab(MM)todisplaythelist
offactoryprocessingpresets.Ifthepresetlistislocked
(grayed-out),touchthe“padlock”icontounlockit.Once
unlocked,simplytouchthedesiredpresetnameinthe
listanditwillbeputdirectly“ontheair".Werecommend
listening to all factory presets to get a feel for their
differencesandthenselectonetostartwith.
4. Touch the “Quick Setup” tab (NN) and adjust the
followingcontrolstosetthebasicloudness,bassand
brightnesssounddesired.
5. Adjust the “Clipper Drive” control (OO) as low as
possible for the loudness needed. This controls the
primaryloudnessvs.distortiontradeoff.Turningitup
makes the sound louder (but more distorted) while
turning it down makes the sound cleaner but not as
loud.Itshouldalwaysbesetaslowaspossibleforthe
levelofloudnessrequired.
6. Settheoverallamountofbassusingthe“Bass”control
(PP). At higher settings of the “Bass Thump” (QQ)
control,the “kick” or “Thump”actionofbassmaterial
isemphasized.
7. Set the basic brightness of a preset by using the
“Presence” (RR), “Treble” (SS) and “Sparkle” (TT)
controls.Notethatthesethreecontrolsonlyboostthe
brightness.Asettingof“0.0”is“flat”ortheminimum
amount of boost for the particular preset that is
currently selected. Reducing brightness can be done,
foroneexample,by reducingthehigherbandsofthe
AGCorLimitermixers.
T
S
U
Z
AA
VW
Y
X
II
KK
JJ
LL
MM
BB
CC
DD
GG
HH
EE
FF
NN
OO
PP
RR
QQ
SS TT
NETWORK CONFIGURATION (CONT.) sysTEm CONFIGURATION sysTEm CONFIGURATION (CONT.) QUICK-sTART INsTAllATION GUIdE
OmNIA.11 sTEREO Fm AUdIO PROCEssOR
Items you need to supply:
• RackwithfouravailableEIArackspacesformounting
• Professionalline-levelanalogorAES/EBUdigitalaudio
sourcesonstandardXLRconnectors
• ConfiguredEthernetswitch
REQUIRED EQUIPMENT, CABLES, AND ACCESSORIES:
Thereareafewadditionalitemsrequiredforasuccessfulinstallation.Checkthelistbelowandmakesure
youhavewhatyouneed.
Included items:
• Omnia.11AudioProcessor
• ACPowercable
• Ethernetcable
• 4rackscrews
WehavemadethisOmniaSystemeasytosetupandconfigure.Thisquick-startguidewilltakeyouthroughthe
basicstepstoconfigureyournewOmnia.11tostartdeliveringcleaner,clearer,louder,andmoreconsistentsound.
Beforewegetstarted,let’smakesureyouhavewhatyouneed.
ThANK yOU FOR PURChAsING ThE OmNIA.11 sTEREO Fm
AUdIO PROCEssOR
CONTINUE TO sysTEm CONFIGURATION
Network configuration is complete. Your system is
readyforsystemconfiguration.Continuetothe“System
Configuration”instructions.
1. Once the system has rebooted, touch the “Setup”
button(S).
2. Touch the Livewire button (T). The Livewire
configurationscreenwillbedisplayed(U).
3. If you do not have a Livewire system, make sure
the 2 Livewire output channels are disabled. The
2 "Enable" buttons (V) will be white if Livewire
is disabled and green when enabled. To disable
Livewire, touch each of the two green "Enable"
buttons(V)toturnthemwhite.
4. If you do have a Livewire system, enable Livewire
bytouchingeachofthetwo"Enable"buttons(V)to
turnthemgreen.
5. IfyouhaveaLivewiresystem,touchthewhitefields
(W) next to the Output #1 and #2 and enter the
appropriatechannelvalueviathepop-upkeyboard(X).
6. Touchthe“APPLY”button(Y)undertheOutputs.
7. Touchthewhitefields(Z)nexttotheInput#1and#2
toentertheappropriatechannelvalueviathepop-
upkeyboard(X).
8. Touchthe“APPLY”buttonundertheInputs(AA).
lIVEWIRE CONFIGURATION
OUTPUT CONFIGURATION
1. Touchthe“Output”icon(II).TheOutputConfigurationscreenwillbedisplayed.Ifthe“Basic”tabisnot
active,touchtoselectit.
INPUT CONFIGURATION
1. Touchthe“ADJ”icon(BB)toreturntotheinitialSystemscreen.
2. Touchthe“Input”icon(CC).TheInputConfigurationscreenwillbedisplayed.Ifthe“Basic”tab(DD)
isnotactive,touchtoselectit.
3. Fromthe“InputSource”drop-down(EE),selecttheAnalog,AES/EBUorLivewireinputasappropriate
foryourinstallation.Ifyouraudiosourceisprovidinganaudiofeedyoushouldseemeteractivityon
thebargraphmeters(FF).
4. Whiledrivingtheinputswithtypicalprogrammaterialatnormaloperatinglevel,adjustthe
appropriate“Master”InputGaincontrol(GG)foryourinstallationuntilthepeak-readinginputbar
graphmetersarereadingjust“intotheyellow”(about–15to–12dBFSorso).Iftheleft/rightaudio
levelscomingintotheOmnia.11aresomewhatunbalanced,youcanadjustthe“RightTrim”control
(HH)tochangetheleveloftherightchannelaloneoveralimitedrange.
©
2016TLSCorp.,AllRightsReserved.
1490-00099-001—QUICKSTARTGUIDE:OMNIA.11C16/15035
yOUR sETUP Is COmPlETE!
That’sit!YouarenowreadytoexperiencetheOmnia.11
forsoundlikeneverbefore.
1. Touchthe“FMOptions”button(JJ)ontheleftsideofthe
MenuAreaandensurethatthePre-Emphasis,Diversity
Delay(ifpresent)andBS-412settings arecorrectfor
yoursystemandyourlocation.
2. Touch the appropriate button (KK) above the “FM
Options”buttontoselectthegroupofoutputcontrols
fortheoutputyouwillbeusing.Alloutputsareactive
simultaneously. Note: If you are using a conventional
AES/EBU L/R digital output to feed an FM exciter or
linearSTL,touchthe“AES/EBU”buttonandbesurethe
“OutputSelection”issetto“FM”andthe“De-emphasis”
isturned“OFF”fortheoutputbeingused.Foraccessto
thecompositeMPXstereogeneratoroutputleveland
stereo pilot controls, touch the “Composite” button.
Note that these controls simultaneously adjust the
OmniaDirectoutput levelsaswell.Finally,adjust the
appropriatecontrolsothatthepeakoutput/modulation
level is correct for the equipment that follows the
Omnia.11.
3. Touchthe“FM”iconbutton(LL)atthetopofthescreen
andthentouchthe“Preset”tab(MM)todisplaythelist
offactoryprocessingpresets.Ifthepresetlistislocked
(grayed-out),touchthe“padlock”icontounlockit.Once
unlocked,simplytouchthedesiredpresetnameinthe
listanditwillbeputdirectly“ontheair".Werecommend
listening to all factory presets to get a feel for their
differencesandthenselectonetostartwith.
4. Touch the “Quick Setup” tab (NN) and adjust the
followingcontrolstosetthebasicloudness,bassand
brightnesssounddesired.
5. Adjust the “Clipper Drive” control (OO) as low as
possible for the loudness needed. This controls the
primaryloudnessvs.distortiontradeoff.Turningitup
makes the sound louder (but more distorted) while
turning it down makes the sound cleaner but not as
loud.Itshouldalwaysbesetaslowaspossibleforthe
levelofloudnessrequired.
6. Settheoverallamountofbassusingthe“Bass”control
(PP). At higher settings of the “Bass Thump” (QQ)
control,the “kick” or “Thump”actionofbassmaterial
isemphasized.
7. Set the basic brightness of a preset by using the
“Presence” (RR), “Treble” (SS) and “Sparkle” (TT)
controls.Notethatthesethreecontrolsonlyboostthe
brightness.Asettingof“0.0”is“flat”ortheminimum
amount of boost for the particular preset that is
currently selected. Reducing brightness can be done,
foroneexample,by reducingthehigherbandsofthe
AGCorLimitermixers.
T
S
U
Z
AA
VW
Y
X
II
KK
JJ
LL
MM
BB
CC
DD
GG
HH
EE
FF
NN
OO
PP
RR
QQ
SS TT
/