Panasonic MCE472 Operating instructions
- Category
- Vacuum cleaners
- Type
- Operating instructions
This manual is also suitable for
Operating Instructions
Vacuum Cleaner
MC-E470E, MC-E472E
We would recommend that you carefully study these Operating Instructions before attempting to operate the unit and that you
note the Important Safety Instructions.
Please keep in a safe place with your authorised Dealer Service booklet.
This product complies with the directives 73/23/EEC and 89/336/EEC.
Panasonic
2
TABLE OF CONTENTS
Page
Caution for AC Mains Lead (UK, IRL only) .............................2
Important Safety Instructions.............................................................3
Identification of main parts...................................................................4
HOW TO ASSEMBLE THE CLEANER
A) Handle assembly
..........................................................................................4
HOW TO OPERATE THE CLEANER
B) Mains lead release
.....................................................................................5
C) ON / OFF Switch (except MC-E470E) ......................................5
D) Beater bar Switch ......................................................................................5
E) Handle lock / release by foot pedal............................................5
F) How to use the accessories..............................................................6
Page
MAINTENANCE AND SERVICING
A) How to empty the dust compartment
......................................7
B) Filter care............................................................................................................8
C) Blockages...........................................................................................................9
D) Maintenance for the beater bar .....................................................9
E) Servicing and Repairs ..........................................................................10
F) Trouble shooting guide........................................................................11
Specifications.................................................................................................11
Vacuum Cleaner Consumables / Accessories .................12
CAUTION FOR AC MAINS LEAD (UK and Republic of Ireland only)
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY
This appliance is supplied with a moulded three pin mains plug for your safety and convenience.
A 13 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 13 amps and that it is approved by
ASTA or BSI to BS1362.
Check for the ASTA mark or the BSI mark on the body of the fuse.
If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a replacement cover is obtained.
A replacement fuse cover can be purchased from your local Panasonic Dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE
REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET.
If a new plug is to be fitted please observe the wiring code as shown below.
If in any doubt please consult a qualified electrician.
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
Blue : Neutral
Brown : Live
As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured
BLACK.
The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured
RED.
Under no circumstances should either of these wires be connected to the earth terminal of the three pin plug, marked with the
letter E or the Earth Symbol
How to replace the Fuse:
• There are two types of the supplied AC Mains Lead: A and B as shown below.
1. Open the fuse compartment with a screwdriver.
2. Replace the fuse and fuse cover if detachable.
A
S
A
TYPE A
TYPE B
3
IMPORTANT SAFETY INSTRUCTIONS
Do not leave the vacuum cleaner plugged in to mains socket. Unplug from the socket when not in use and before cleaning the
appliance or undertaking maintenance operations.
This appliance is not intended for use by young children or infirm people without supervision; young children should be
supervised to ensure that they do not play with the appliance.
Do not use if the mains lead or mains plug is damaged. If the vacuum cleaner is not working as it should be, or has been
dropped, damaged, left outdoors, or come into contact with water, consult an authorised Panasonic Service Centre.
Do not pull or carry by the mains lead, use the mains lead as a handle, close a door on the mains lead, pull the mains lead
around sharp edges or corners. Do not run over the mains lead with the vacuum cleaner. Keep the mains lead away from
heated surfaces.
Do not run vacuum cleaner over tassels or fringes of rugs or mats.
Do not handle plug or vacuum cleaner with wet hands.
Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair and anything that may
block or reduce air flow.
Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts.
Do not use without filters and / or dust compartment in place.
Turn off all controls before unplugging. Do not pull on the mains lead when disconnecting the vacuum cleaner from the mains,
pull on the plug body itself.
Use extra care when cleaning on stairs.
Do not use to pick up flammable or combustible materials, or others that may become so or use in areas where they may be
present.
Do not let the vacuum cleaner pick up wet matter, burning ashes or large or sharp objects.
This appliance should be serviced by an authorised Panasonic Service Centre and only genuine Panasonic spare parts should
be used.
Keep feet, fingers and hands away from the beater bar. Also avoid putting them between cleaner bodies. (It may cause injury)
NOTE: This vacuum cleaner is designed for general household use only and is not suitable for use in a garage or to suck
up liquids.
Before using the vacuum cleaner, please read these basic precautions.
WARNING: To reduce the risk of fire, electric shock or injury:
4
IDENTIFICATION OF MAIN PARTS
HOW TO ASSEMBLE THE CLEANER
A-1)Handle
B)Mains lead
C)ON/OFF Switch
D)Beater bar switch
(except MC-E470E)
G)Maximum dust
level mark
Main-filter A
Main-filter B
Pre-filter
Exhaust cover /
Clean air filter
Cleaning head
Furniture guard
A-3) Cord clip
A-4) Upper cord hook
A-2) Hose clip
A-4)Lower cord hook /
Carrying handle
A-2) Hose
F) Dusting brush
F) Hose support
A) HANDLE ASSEMBLY
IMPORTANT: Do not overtighten
the screw.
1 2 3 4
Dust compartment
lock
F) Crevice nozzle
F) Extension
wand
2
1
E) Foot pedal
(handle release)
1
2
5
HOW TO OPERATE THE CLEANER
B) MAINS LEAD RELEASE
E) HANDLE LOCK / RELEASE BY FOOT PEDAL
To unlock the handle of the cleaner, step on the pedal. To return into the upright position, simply put the handle back.
C) ON/OFF SWITCH
D) BEATER BAR SWITCH (except MC-E470E)
On hard floors / Using the accessories
IMPORTANT: Ensure the cleaner is switched ON before moving the Beater bar switch.
To prevent scratches or other damage to
hard floors, Linoleum, etc., slide the Beater
bar switch to the “STOP” position.
On carpeted floors
DO NOT leave the beater bar rotating in the same place for too long.
ATTENTION: Refer to your carpet manufacturers cleaning recommendations.
Some more delicate carpets and long pile carpets may require that they be
vacuumed with the Beater bar off, to prevent damage.
BEATER BARSTOP
1 2 3
Step
one
time
Step a
second
time
6
F) HOW TO USE THE ACCESSORIES
IMPORTANT: When using the accessories, keep the vacuum cleaner in the upright position and ensure that the cleaner
is switched ON before moving the Beater bar switch to the STOP position.
CAUTION:
While using the accessories, hold the handle with one hand
to avoid pulling the cleaner over.
On model MC-E470E to prevent damage to carpeted floors,
Linoleum, etc., tilt the cleaner back so that the cleaning
head is raised off the floor.
To avoid accidental injury, keep children away from the
beater bar while in operation.
1 2 3
4
STOP
2
1
Note: Excluding MC-E470E.
7
MAINTENANCE AND SERVICING
A) HOW TO EMPTY THE DUST COMPARTMENT
Clean the pre-filter by
brushing the dust off with a
soft brush.
1 2 3
4 5
8 9
6 7
IMPORTANT: Empty the dust compartment before the dust reaches the ( ) mark.
Inner
seals
1
2
2
1
2
IMPORTANT NOTE: Before servicing any part, always DISCONNECT THE CLEANER FROM THE MAINS SUPPLY.
1
NOTE: The dust compartment may be washed with warm water.
DO NOT use detergents or other cleaning fluids to avoid deterioration of the plastic and the rubber seals.
DO NOT attempt to clean the dust compartment in a dishwasher.
IMPORTANT: Before re-assembling the dust compartment, ensure that it is completely dry and check that the rubber inner
seals are in place.
Remove the dust
compartment cover by
pushing the tabs in and
lifting off.
Remove dust accumulated in the filter A and B by tipping them
against a hard surface. If dust remains on filter A, replace with
the spare or carry out further cleaning detailed on following
page.
Tab
Tab
A
B
Click
Click
Tab
Tab
NOTE: Under normal use, it is advisable to change the clean air filter once or twice a year.
CAUTION: Never attempt to wash the HEPA filter. Under normal usage it will not require replacement.
The central filter should be cleaned or
replaced when it becomes dirty.
To clean the filter, rinse it out in warm
water and dry it thoroughly before
replacing.
2) Central filter
3) Clean air filter / HEPA Filter (depending on model)
1
1 2
HEPA Filter
2
3
1
2
Remove the filter as shown.
Insert the new one with the
rubber seal towards the main
body.
8
B) FILTER CARE
CAUTION
DO NOT use detergents or other cleaning fluids to clean the filters. They may deteriorate the plastic.
DO NOT use hot air or hot surface to dry the filters. Keep at room temperature for approximately 24 hours.
IMPORTANT: Before re-installing the washable filters, make sure they are completely dry to avoid damaging the cleaner.
Cleaning or Replacing the filters
NOTE: For ease of access to the filter maintenance, remove the dust compartment (see page 7).
1) Pre-filter / Main filter A/ Main-filter B
1 2 4
A
B
Click
Click
Tab
Tab
Remove the dust
compartment cover by
pushing the tabs in and
lifting off.
Remove main filter B and
A.
Remove dust accumulated in the filter A
and B by tipping them against a hard
surface.
NOTE: If after having removed the dust,
there is not enough airflow, clean them
out in warm water or replace with a new
one.
Tab
Tab
9
C) BLOCKAGES
If your cleaner stops picking up dust while the dust compartment is not yet full, a blockage may have occurred in the hose
or suction pipe inlet. If necessary, remove the obstruction in the hose or suction pipe inlet as indicated.
D) MAINTENANCE FOR THE BEATER BAR
1
2 43 5
NOTE: Take care not to cut the brush.
CAUTION: Ensure the cleaner is DISCONNECTED from the mains supply before any beater bar maintenance.
2
1
2
1
Suction pipe inlet
10
E) SERVICING AND REPAIRS
We always recommend the use of genuine Panasonic replacement parts.
To replace any of the following parts, place the cleaner in the horizontal position by using the pedal and turn it over exposing the
underside.
CAUTION: Before replacing any part DISCONNECT THE CLEANER FROM THE MAINS SUPPLY.
Release the belt from the motor shaft and
lift the beater bar assembly to remove the
belt.
To re-assemble, place the belt around
the motor shaft and around the beater
bar pulley.
Insert the beater bar mounts into their
housings, then turn the beater bar by
hand to ensure that the belt has been
seated correctly.
IMPORTANT: On model MC-E470E,
when installing the belt, make sure
it is placed between the screw and
the inside cover rib, as indicated.
Re-fit the base plate and replace the
screws.
Remove the 4 screws from the base
plate and lift it off.
1 2 3
How to replace - Drive belt (Type UB-1L) / Beater bar assembly
MC-E470E only
Screw
Cover
rib
11
F) TROUBLE SHOOTING GUIDE
TROUBLE CHECK POINT CAUSE / REMEDY
Motor fails to rotate
(no noise is heard at all).
Thermal Cut-out
This vacuum cleaner is fitted a thermal cut-out device which automatically turns off the cleaner to prevent overheating of the
motor. When this happens, disconnect the cleaner from the mains socket and check the dust compartment as it may be full
or clogged with fine dust. Check for any other obstructions.
After emptying the dust compartment or removing the obstruction, leave the vacuum cleaner to cool down until the thermal
cut-out resets after approximately 40 minutes.
Important: The thermal cut-out will not reset if the unit is not disconnected from the mains socket.
Mains lead
IMPORTANT: If the mains lead becomes damaged, it must be repaired by Panasonic, or an authorised Service Centre or a
qualified person in order to avoid any hazard.
Mains plug connection.
Mains plug fuse (UK, IRL only)
Thermal cut-out device may
have operated.
Check that the mains plug is connected firmly and mains socket is ON.
Check fuse and replace if blown.
(See Thermal cut-out protection features below described).
Motor runs but there is
no suction.
Check dust mark.
Pre-filter.
Check dust accumulated on
main filter A / B.
Central filter.
Check hose is properly inserted to
the suction pipe inlet.
Hose inlet is blocked.
If it shows full, empty the dust compartment.
If the pre-filter is full of dust, clean it or replace.
Remove dust accumulated or replace the filter. (See FILTER CARE)
If central filter is full of dust, clean or replace it. (See FILTER CARE)
Re-insert the hose to suction pipe inlet correctly.
If there is a blockage, remove it.
Beater bar does not
rotate.
Clogged by a large object in
the beater bar housing.
Belt broken or loose.
Check beater bar switch is
correctly positioned
(except MC-E470E).
If there is any obstruction, remove it.
If the belt is broken, replace it. If loose re-install it again.
Place the beater bar switch to the appropriate position.
SPECIFICATIONS MC-E470E MC-E472E
Power source 230-240V / 50Hz 230-240V / 50Hz
Max. Output 1400W 1600W
Nominal output 1100-1200W 1250-1350W
Dimensions (W x L x H) 315 x 310 x 1050 315 x 310 x 1050
Net weight 6.9 kg 6.9 kg
Dusting brush √√
Extension wand √√
Crevice nozzle √√
Before returning the vacuum cleaner to a Panasonic Service Centre, check the following points.
CAUTION: DISCONNECT from the mains socket before carrying out any kind of maintenance operation.
VACUUM CLEANER CONSUMABLES / ACCESSORIES
(For UK and Republic of Ireland customers only)
DESCRIPTION
MC-E470E MC-E472E
Extension wand Product code Product code
AMC8A1291034 AMC8A1291034
Crevice nozzle Product code Product code
AMC8A1391034 AMC8A1391034
Dusting brush Product code Product code
AMC8A97G1034 AMC8A97G1034
Blister pack of 2 / belts Product code Product code
AMC8S03G2000 AMC8S03G2000
Beater bar assembly
Note: Specifications are subject to change without notice.
Product code Product code
AMC8R98G1064 AMC8R98G1064
Handle screw Product code Product code
AMC8H10B1000 AMC8H10B1000
Handle Product code Product code
AMC8H99G1077 Red AMC8H99G1061
AMC8H99G1020 White
Dust compartment filters
(Main filter A and B)
Product code Product code
AMC8S86BA000 AMC8S86BA000
Clean air filter
or
HEPA Filter Type F-2H
Product code Product code
AMC8F28T1000 AMC8S04W5000
or
AMC8S04W5000
Central filter Product code Product code
AMC8F03W5000 AMC8F03W5000
Pre-filter Product code Product code
AMC8F40BA070 AMC8F40BA070
Dust compartment Product code Product code
AMC8T58R9001 AMC8T58BB001
Dust compartment cover assembly Product code Product code
AMC8T82BA061 AMC8T82BA061
Sales and Suport Information
Customer Care Center
For UK Customers: 0870 900 9043
For Republic of Ireland customers: 01 298 8333
Visit our website for product information
E-mail: [email protected]
Direct sales at Panasonic UK
Order accessory and consumable items for your product with ease and confidence by
telephoning our Customer Care Centre Mon - Fri 9:00 am - 5:30 pm (except public holidays).
Or go on line through our Internet Accessory ordering application at www. panasonic.co.uk.
Most major credit and debit cards accepted.
All enquiries, transactions and distribution facilities are provided directly by Panasonic UK Ltd.
It couldn’t be simpler!
Also available through our internet is direct shopping for a wide range of finished products, take
a browse on our website for further details.
Z07BA090 Printed in Spain
Matsushita Electric España, S.A.
VACUUM CLEANER DIVISION
Zona Industrial del Polígono de CELRÀ
17460 CELRÀ (Girona) SPAIN
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Panasonic MCE472 Operating instructions
- Category
- Vacuum cleaners
- Type
- Operating instructions
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Panasonic MCE4013 Operating instructions
-
-
-
-
-
-
-
-
-
