Liebherr EKB 9471 Assembly And Installation Instructions

EKB 9471
Liebherr
Brand
Liebherr
Model
EKB 9471
Category
Fridges
Type
Assembly And Installation Instructions

This manual is also suitable for

7083 461-00
ECBN 5066
Installation instructions
for NoFrost combined refrigerator-freezers
2
Setting up
•Avoidpositioningtheapplianceindirectsunlightornearcook-
ers,radiatorsandsimilarsourcesofheat.
•Theflooronwhichtheappliancestandsshouldbehorizontal
andlevel.
• StandardEN378specifiesthattheroominwhichyouinstall
yourappliancemusthaveavolumeof1m³per8gofR600a
refrigerantusedintheappliance,soastoavoidtheformationof
inflammablegas/airmixturesintheroomwheretheappliance
islocatedintheeventofaleakintherefrigerantcircuit.The
quantityofrefrigerantusedinyourapplianceisindicatedon
thetypeplateontheinsideoftheappliance.
Electrical connection
Onlyoperatetheappliancewithalternating current (AC).
The permissible voltage and frequency are indicated on the
typeplate.
Thepositionofthetypeplateisshowninthesectionentitled
Description of the appliance (in the operating instructions).
Thesocketmustbeproperlyearthedandprotectedbyafuse.
Thetrippingcurrentofthefusemustbebetween10Aand16A.
Thesocketmustnotbesituatedbehindtheappli-
anceandmustbeeasilyaccessible.
Donotconnecttheapplianceusinganexten-
sioncableorextensionsocket.
Donotusestand-aloneinverters(conversion
of direct current to alternating/three-phase
current)orenergy-savingplugs.Riskofdam-
agetotheelectroniccontrolsystem!
Door swing clearance at
locations next to a wall
Please allowfordoor swing clear-
anceatlocationsnexttoawall.
Theillustratedmeasurementiswith-
outmountedfrontpanels.
Besuretoaddyourpanelthickness
andhandledepthtothismeasure-
mentinordertoavoidinterferences.
Content Page
Settingup................................................................................ 2
Electricalconnection............................................................... 2
Applianceventing....................................................................2
Doorswingclearanceatlocationsnextoawall...................... 2
Appliancedimensions............................................................. 3
Installationdimensions............................................................ 3
DefinitionofInsetInstallationStyle......................................... 4
Paneldimensions-Insetinstallationstyle............................... 4
DefinitionofFramelessInstallationStyle................................ 4
Paneldimensions-Framelessinstallationstyle..................... 4
Doorswingclearance-InsetInstallationStyle...................... 5
Doorswingclearance-FramelessInstallationStyle............ 6
Mountingtheanti-tippingdevice............................................. 7
Mountingoptions..................................................................... 7
Connectiontothewatersupply............................................... 8
Waterpressure........................................................................ 8
Installation............................................................................... 8
Levelingtheappliance.......................................................... 10
Fasteningtheapplianceintherecess................................... 10
Mountingtheventilationgrille................................................ 10
Adjustingtherefrigeratordoor............................................... 12
Adjustingthefrontofthedrawer............................................ 12
Removingthemountingaccessoriesfromtherefrigerator
door....................................................................................... 12
Removingthemountingaccessoriesfromthefreezer
drawers.................................................................................. 12
Mountingtheattachmentbracketsontothedoorpanels...... 13
Mountingtherefrigeratorpanel............................................. 14
Mountingthefreezerpanels.................................................. 15
Changingoverdoorhinges................................................... 15
Appliance venting
Therequiredairflowisdirected
throughtheplinth.
Itisimportanttousetheprovided
ventilationgrillefortheventila-
tionopening.
Thisopeningmustnotbe
covered.
3
Appliance dimensions
A=76mm
B=2027mm
C=757mm
D=610mm
E=1413mm
F=952mm
Installation dimensions
Thelocationofthesocketcanwithinaradiusof2000mmfrom
theappliancetopcenter.
Theicemakerisfittedinthefreezercompartmentofthecom-
bined refrigerator-freezer. It must be connected to the mains
watersupplytowork.
Thewatershut-offtapmustbepositionedwithintheareasmarked
ingrey.
Important!
Donotinstalltheshut-offtapbehindtheappliance.
WARNING!
The water shut-o tap must not sit directly
above the socket!
The gap between the water shut-o tap
and the socket must comply with the
regulations of the country in which the
appliance is used!
Thistypeofdimension
lineindicatestheheight
measuredfromthefloor.
Cabinet depth D
625 mm + panel thickness>Insetinstallationstyle
625 mm>Framelessinstallationstyle
Explanationof"Installationstyles"seepage4.
4
Panel dimensions - Inset installation style
Min.panelthickness=16mm
Max.panelthickness=38mm
Maximum panel weight
Refrigeratorpanel=27kg
Freezerdrawerpanel=10kg
Panel dimensions - Frameless installation style
Definition of Inset Installation Style
Applianceandpanelssitfullywithintheopeningandareflush
withwhatcouldbeitsownbox,betweentwopantrycabinetsor
decorativecolumns.
Definition of Frameless Installation Style
Withthisinstallationstyle,thesewiderappliancepanelspartially
overlaythesharedsidegablesofadjacentcabinetrysoasto
mimicthelookofaframelessstylecabinet.
Side view of cabinet (sectional view)
Cabinet frame
Doorpanel
Side view of cabinet (sectional view)
Cabinet frame
Doorpanel
The height of the bottom panel can be reduced by up to 50 mm to accommodate higher plinths
5
Rightsidewallofappliancehousing
Frontofappliancehousing
Top View
Frontpanel-doorclosed
Panel
thickness
Panel
thickness
Frontpanel-dooropeningangle=115°
Door swing clearance - Inset Installation Style
6
Rightsidewallofappliancehousing
Frontofappliancehousing
Top View
Frontpanel-doorclosed
Panel
thickness
Panel
thickness
Frontpanel-dooropeningangle=115°
Door swing clearance - Frameless Installation Style
7
Mounting the anti-tipping device
WARNING!
The supplied anti-tipping bracket must be
installed in all cases. This prevents the appli-
ance from tipping over when the fully loaded
door is opened.
Installation:
1. Markthecentrelineoftheapplianceonthefloor.
Aligntheanti-tippingbracketcentretothecentreline.
2. Dependingontheconstitutionofthefloorandwall,useany
possiblemountingoptionasshowninchapterMounting Op-
tions.T h escre ws(6 x60)ar e suppl i e d witht h eacces so r y pack .
Important!
If the floor slopes down sideways, the anti-tipping
bracket must be fitted horizontally. Lay down spacers
in the appropriate positions.
CAUTION!
Ensure that there are no electric cables or water
pipes in the wall section to which the anti-tipping
bracket is to be secured. These could be damaged
during installation.
Mounting options
Wall
Floor
Mountingthebracketwiththewallstuds.
Mountingwithplugstoconcretewalls.
3Screws6x60mm
Wall
Floor
Mountingwiththewallplateturningin
thescrewsatanangle.
3Screws6x60mm
Wall
Floor
Mountingwithwoodenfloors.
Mountingwithplugstoconcretefloors.
3Screws6x60mm
8
3.
4.
3. Insert the bent section of the hose
throughtheopeningattherightside
oftheappliance.
4. Movethehosetothefrontandcon-
nectwiththevalveconnector.
Be sure the connection is tightly
arranged.
Valve connector
Installation
1. Placetheapplianceinfrontoftheinstallationrecess.
2. A p p l yc ov e rstr i p sab ove,b et-
weenandbelowthesecuring
platesonthesidewallsofthe
appliance.
 Cutthecoverstripstotheright
lengthforthispurpose.
 Fittheadhesivecoverstrips
leaving a gap of 6,5 mm to
each securing plate. This
ensuresproblem-freefitting
ofthecovers.
2.
Connection to the water supply
Safety instructions and warnings
•Do not connect to the water supply while the
combined refrigerator-freezer is connected to
theelectricitysupply.
•Theconnectiontothemainswatersupplymay
onlybemadebytrainedpersonnel.
•Thewaterqualitymustcomplywiththedrinking
waterdirectivesofthecountryinwhichtheap-
plianceisused.
•Theicemakerisdesignedexclusivelytomake
icecubesinquantitiesrequiredbyahousehold
andmayonlybeoperatedwithwatersuitablefor
thispurpose.
•Allrepairsandworkontheicemakermayonly
becarriedoutbycustomerservicepersonnelor
othertrainedpersonnel.
•Themanufacturercannotacceptliabilityfordam-
agecausedbyafaultyconnectiontothemains
watersupply.
Water pressure
The water pressure must be between 150 and
600 KPa (1.5 - 6 bar).
Important!
Ifthewaterfilter
isinsertedintheappliance,thewater pressure
mustliebetween300 and 600 KPa (3 - 6 bar).
If the water pressure with the inserted water
filter is too low, this may cause the ice maker to
malfunction.
Thewatersupplytotheappli-
ancemustbethroughacold
waterpipethatcanwithstand
the operating pressure and
complies with the hygiene
regulations.
Forthis,usethestainlesssteelhosesupplied(length3m).
9
6. Routethemainscabletowardsthesocket.
7. Routethewaterhosetowardsthewatershut-offtap.
6.
7.
8. Pushtheapplianceslowlyintotherecessuntilthecompressor
mountingplatetouchestheanti-tippingbracket.
9. Fillthehosewithwaterandconnecttotheshut-offtap.
Be sure the connection is tightly arranged.
 Opentheshut-offtapandcheckthesystemforleakage.
Important!
Aftertheicemakerhasbeenswitchedon,thewater
supplysystemmustbebled.
SeethesectionBleeding the ice makerintheop-
eratinginstructions.
8.
5. Locatethewaterhoseintotherailof
theappliancebase.
5.
WARNING!
Do not connect the appliance to the power supply
until the installation is completed.
CAUTION!
Lay the mains cable and the water hose in such
a way that they will not be damaged when the
appliance is slid into the installation recess.
10
Mounting the ventilation grille
 Pulloutthebottomfreezerdrawer.
1. Removetheblueprotectionfilmfromthedustfilter
providedandinsertthefilterintoitsopening
in the plinth. Engage the filter at the
bot t o m ,p re s s d ownt heb ut t o n a n d
clickintoplace.
3.Insertthesupportsfortheventilationgrille
ontheleftandrightsidesinthemotor
compartment.
2.Remove the locking pins of
bothsupports.Thesupports
are provided with the appli-
anceaccessorypack.
1.
2.
3.
Fastening the appliance in the recess
Onceintherecess,securetheapplianceto
thebodyoftheunitusingthesecuring
plates(4x16screws).
Thenclickthecoverssup-
pliedintoplace.
Leveling the appliance
1. Adjusttheheightoftheapplianceatthefrontbytwistingthe
levelingfeet
1
.Usetheopen-endedspannerprovided.
Turnthespannercounterclockwisetoraisetheappliancefront
andclockwisetolowerit.
 Positionthespanneraccordingly(
1
).
2. Adjusttheheightoftheapplianceattherearbyturningthe
adjustingbolts
2
.Usea 1/4"boxspanner or theTorx25
wrenchprovided.
3. Rotatelevelingfeet
1
untilfirmlyinplaceagainstthefloor.
WARNING!
To prevent the appliance from tipping forward
the leveling feet
1
must have contact with
the floor.
11
5.
5. Insert the locking pins to block the
supports.
6. Installtheventilationgrille.
 Thegrillehasboltsontheinside(seedetailinthedrawing
below).Theseboltsmustbeinsertedintotheholesofthe
supports.
4. Thefrontedgeofthebrackets
is flush with the front of the
ventilationgrille.
 Adjustthesupportsaccordingly.
7. Adjusttheheightoftheventilationgrille.
• Loosenthegrubscrewsatthefrontofthegrille(Allenkey
A/F2.5).
• Adjusttheventilationgrilletothedesiredheight.
• Tightenthegrubscrews.
7.
4.
6.
12
Removing the mounting accessories from the
refrigerator door
Removethecover
1
andunscrewthetopandbottomattach-
mentbrackets
2
fromtherefrigeratordoor.Theseattachment
bracketswillbemountedontotherefrigeratordoorpanel.
Important!
The securing nuts are needed for re-mounting the pre-
assembled door panel onto the refrigerator door.
Removing the mounting accessories from the
freezer drawers
Unscrewtheattachmentbrackets
3
fromthefreezerdrawers.
These attachment brackets will be mounted onto the freezer
panels.
Important!
The screws are needed for re-mounting the pre-assembled
freezer panels onto the freezer drawers.
Adjusting the refrigerator door
Thelateraltiltoftherefrigeratordoorcanbeadjustedifrequired.
Undoscrews
1
.Adjustthelateraltiltusingthegrubscrew
2
(AllenkeyA/F2.5).
Adjusting the front of the drawer
Ifrequired,thefrontofthefreezerdrawerscanbeadjusted.
Transferthescrewsshownintheillustration(ontheleftandright
sidesofthefreezerdrawer)individuallytothelongslotsbelow.
Tighten the screwsinthe frontofthedrawer onceitisinthe
rightposition.
Side view of the freezer drawer
pulled out
13
Mounting the attachment brackets onto the door panels
1. Drawaline1041mmfromthebottomsideofthedoorpanel.
2. Drawafurtherline107.5mmfromthebottomsideofthedoorpanel.
3. Alignoneoftherefrigeratordoorattachmentbracketstothetopline,asshownintheillustrationbelow,andsecurewithatleast
6screws(4x14).
4. Alignthesecondrefrigeratordoorattachmentbrackettothebottomline,asshownintheillustrationbelow,andsecurewithat
least6screws(4x14).
5. Secureeachoftheattachmentbracketsthathavebeenremovedfromthefreezerdrawersusing3screws(4x14),asshownin
theillustrationbelow.
Refrigeratordoorpanel
Freezerdrawerpanel
Freezerdrawerpanel
14
fig. D
Mounting the refrigerator panel
fig. A
fig. B
fig. C
1. Screwintheadjustingpinson
theundersideoftherefrigerator
doorcompletely(fig. A).
2. Opentherefrigeratordoorandsus-
pendtherefrigeratorpanelonthetop
adjustingpins(fig. B).
3. Screwsecuringnutsontotheadjust-
ingpinsandslightlytighten.
4. Closetherefrigeratordoorandchecktheheight
ofthepanel.
5. Adjusttheheightofthe panelif necessary.
Undothesecuringnutsandusetheadjusting
pinstoadjust(fig. C).
6. Adjustthepanelhorizon-
tally(usingthelongslots
intheattachmentbracket)
(fig. D).
7. Tightenthesecuringnuts.
fig. E
fig. F
8. Removetheadjustingpins
(bottom of therefrigerator
door)untilthesetouchthe
attachmentbracket(fig. E).
9. Screwonthesecuringnutsandtighten(fig. F).
15
Mounting the freezer panels
1. Pulloutthetopfreezerdrawerandscrewonthepre-assembled
panel.Thesamescrewsmustbeusedasthoseusedtoscrew
ontheattachmentbrackets(3.5x13).
2. Closethefreezerdrawerandcheckthepositionofthepanel.
Adjusttheheightofthepanelbyundoingtheleftandright
screws.Tightenthescrews.
3.Pulloutthebottomfreezerdrawerandmountthepanelinthe
sameway.
4. Forbothdrawers,coverthegapbetweenthedrawerandthe
panelwiththecoverstripssupplied.Removetheprotective
filmfromthetrimandinsertintothegapatthetop.
3.5x13mm
Changing over door hinges
Doorhingesshouldonlybechangedbyatrainedexpert.
WARNING!
Do not try to change over the door hinges your-
self. The refrigerator door hinges are fitted with
strong closing springs. If the hinge accidentally
snaps shut, this can lead to serious injury.
11. Clickthetopandbottomcoversintoplace1 (fig. H)
Insertthecoverstripprovided2betweenrefrigeratordoor
andpanel.
fig. H
fig. G
10. Undothethreescrewsonthetopoftheattach-
mentbracket,adjustthedoorpanelasdisplayed
in fig. Gandthenretightenthescrews.Thesame
procedure can be carried out for the bottom
attachmentbracket.
LiebherrHausgeräteLienzGmbH*Dr.-Hans-Liebherr-Strasse1*A-9900Lienz**www.liebherr.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Liebherr EKB 9471 Assembly And Installation Instructions

EKB 9471
Liebherr
Brand
Liebherr
Model
EKB 9471
Category
Fridges
Type
Assembly And Installation Instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents