Liebherr ECBN 5066 PremiumPlus Assembly And Installation Instructions

Brand: Liebherr

Model: ECBN 5066 PremiumPlus

Category: Fridges

Type: Assembly And Installation Instructions

This manual is also suitable for

The Liebherr ECBN 5066 PremiumPlus is a NoFrost combined refrigerator-freezer that offers advanced features for food preservation and convenience. With its spacious interior, flexible storage options, and innovative technologies, this appliance is designed to meet the needs of modern households.

7083 461-00

ECBN 5066

Installation instructions

for NoFrost combined refrigerator-freezers

Setting up

•Avoidpositioningtheapplianceindirectsunlightornearcook-

ers,radiatorsandsimilarsourcesofheat.

•Theflooronwhichtheappliancestandsshouldbehorizontal

andlevel.

• StandardEN378specifiesthattheroominwhichyouinstall

yourappliancemusthaveavolumeof1m³per8gofR600a

refrigerantusedintheappliance,soastoavoidtheformationof

inflammablegas/airmixturesintheroomwheretheappliance

islocatedintheeventofaleakintherefrigerantcircuit.The

quantityofrefrigerantusedinyourapplianceisindicatedon

thetypeplateontheinsideoftheappliance.

Electrical connection

Onlyoperatetheappliancewithalternating current (AC).

The permissible voltage and frequency are indicated on the

typeplate.

Thepositionofthetypeplateisshowninthesectionentitled

Description of the appliance (in the operating instructions).

Thesocketmustbeproperlyearthedandprotectedbyafuse.

Thetrippingcurrentofthefusemustbebetween10Aand16A.

Thesocketmustnotbesituatedbehindtheappli-

anceandmustbeeasilyaccessible.

Donotconnecttheapplianceusinganexten-

sioncableorextensionsocket.

Donotusestand-aloneinverters(conversion

of direct current to alternating/three-phase

current)orenergy-savingplugs.Riskofdam-

agetotheelectroniccontrolsystem!

Door swing clearance at

locations next to a wall

Please allowfordoor swing clear-

anceatlocationsnexttoawall.

Theillustratedmeasurementiswith-

outmountedfrontpanels.

Besuretoaddyourpanelthickness

andhandledepthtothismeasure-

mentinordertoavoidinterferences.

Content Page

Settingup................................................................................ 2

Electricalconnection............................................................... 2

Applianceventing....................................................................2

Doorswingclearanceatlocationsnextoawall...................... 2

Appliancedimensions............................................................. 3

Installationdimensions............................................................ 3

DefinitionofInsetInstallationStyle......................................... 4

Paneldimensions-Insetinstallationstyle............................... 4

DefinitionofFramelessInstallationStyle................................ 4

Paneldimensions-Framelessinstallationstyle..................... 4

Doorswingclearance-InsetInstallationStyle...................... 5

Doorswingclearance-FramelessInstallationStyle............ 6

Mountingtheanti-tippingdevice............................................. 7

Mountingoptions..................................................................... 7

Connectiontothewatersupply............................................... 8

Waterpressure........................................................................ 8

Installation............................................................................... 8

Levelingtheappliance.......................................................... 10

Fasteningtheapplianceintherecess................................... 10

Mountingtheventilationgrille................................................ 10

Adjustingtherefrigeratordoor............................................... 12

Adjustingthefrontofthedrawer............................................ 12

Removingthemountingaccessoriesfromtherefrigerator

door....................................................................................... 12

Removingthemountingaccessoriesfromthefreezer

drawers.................................................................................. 12

Mountingtheattachmentbracketsontothedoorpanels...... 13

Mountingtherefrigeratorpanel............................................. 14

Mountingthefreezerpanels.................................................. 15

Changingoverdoorhinges................................................... 15

Appliance venting

Therequiredairflowisdirected

throughtheplinth.

Itisimportanttousetheprovided

ventilationgrillefortheventila-

tionopening.

Thisopeningmustnotbe

covered.

Appliance dimensions

A=76mm

B=2027mm

C=757mm

D=610mm

E=1413mm

F=952mm

Installation dimensions

Thelocationofthesocketcanwithinaradiusof2000mmfrom

theappliancetopcenter.

Theicemakerisfittedinthefreezercompartmentofthecom-

bined refrigerator-freezer. It must be connected to the mains

watersupplytowork.

Thewatershut-offtapmustbepositionedwithintheareasmarked

ingrey.

Important!

Donotinstalltheshut-offtapbehindtheappliance.

WARNING!

The water shut-o tap must not sit directly

above the socket!

The gap between the water shut-o tap

and the socket must comply with the

regulations of the country in which the

appliance is used!

Thistypeofdimension

lineindicatestheheight

measuredfromthefloor.

Cabinet depth D

625 mm + panel thickness>Insetinstallationstyle

625 mm>Framelessinstallationstyle

Explanationof"Installationstyles"seepage4.

Panel dimensions - Inset installation style

Min.panelthickness=16mm

Max.panelthickness=38mm

Maximum panel weight

Refrigeratorpanel=27kg

Freezerdrawerpanel=10kg

Panel dimensions - Frameless installation style

Definition of Inset Installation Style

Applianceandpanelssitfullywithintheopeningandareflush

withwhatcouldbeitsownbox,betweentwopantrycabinetsor

decorativecolumns.

Definition of Frameless Installation Style

Withthisinstallationstyle,thesewiderappliancepanelspartially

overlaythesharedsidegablesofadjacentcabinetrysoasto

mimicthelookofaframelessstylecabinet.

Side view of cabinet (sectional view)

Cabinet frame

Doorpanel

Side view of cabinet (sectional view)

Cabinet frame

Doorpanel

The height of the bottom panel can be reduced by up to 50 mm to accommodate higher plinths

Rightsidewallofappliancehousing

Frontofappliancehousing

Top View

Frontpanel-doorclosed

Panel

thickness

Panel

thickness

Frontpanel-dooropeningangle=115°

Door swing clearance - Inset Installation Style

Rightsidewallofappliancehousing

Frontofappliancehousing

Top View

Frontpanel-doorclosed

Panel

thickness

Panel

thickness

Frontpanel-dooropeningangle=115°

Door swing clearance - Frameless Installation Style

Mounting the anti-tipping device

WARNING!

The supplied anti-tipping bracket must be

installed in all cases. This prevents the appli-

ance from tipping over when the fully loaded

door is opened.

Installation:

1. Markthecentrelineoftheapplianceonthefloor.

Aligntheanti-tippingbracketcentretothecentreline.

2. Dependingontheconstitutionofthefloorandwall,useany

possiblemountingoptionasshowninchapterMounting Op-

tions.T h escre ws(6 x60)ar e suppl i e d witht h eacces so r y pack .

Important!

If the floor slopes down sideways, the anti-tipping

bracket must be fitted horizontally. Lay down spacers

in the appropriate positions.

CAUTION!

Ensure that there are no electric cables or water

pipes in the wall section to which the anti-tipping

bracket is to be secured. These could be damaged

during installation.

Mounting options

Wall

Floor

Mountingthebracketwiththewallstuds.

Mountingwithplugstoconcretewalls.

3Screws6x60mm

Wall

Floor

Mountingwiththewallplateturningin

thescrewsatanangle.

3Screws6x60mm

Wall

Floor

Mountingwithwoodenfloors.

Mountingwithplugstoconcretefloors.

3Screws6x60mm

3. Insert the bent section of the hose

throughtheopeningattherightside

oftheappliance.

4. Movethehosetothefrontandcon-

nectwiththevalveconnector.

Be sure the connection is tightly

arranged.

Valve connector

Installation

1. Placetheapplianceinfrontoftheinstallationrecess.

2. A p p l yc ov e rstr i p sab ove,b et-

weenandbelowthesecuring

platesonthesidewallsofthe

appliance.

 Cutthecoverstripstotheright

lengthforthispurpose.

 Fittheadhesivecoverstrips

leaving a gap of 6,5 mm to

each securing plate. This

ensuresproblem-freefitting

ofthecovers.

Connection to the water supply

Safety instructions and warnings

•Do not connect to the water supply while the

combined refrigerator-freezer is connected to

theelectricitysupply.

•Theconnectiontothemainswatersupplymay

onlybemadebytrainedpersonnel.

•Thewaterqualitymustcomplywiththedrinking

waterdirectivesofthecountryinwhichtheap-

plianceisused.

•Theicemakerisdesignedexclusivelytomake

icecubesinquantitiesrequiredbyahousehold

andmayonlybeoperatedwithwatersuitablefor

thispurpose.

•Allrepairsandworkontheicemakermayonly

becarriedoutbycustomerservicepersonnelor

othertrainedpersonnel.

•Themanufacturercannotacceptliabilityfordam-

agecausedbyafaultyconnectiontothemains

watersupply.

Water pressure

The water pressure must be between 150 and

600 KPa (1.5 - 6 bar).

Important!

Ifthewaterfilter

isinsertedintheappliance,thewater pressure

mustliebetween300 and 600 KPa (3 - 6 bar).

If the water pressure with the inserted water

filter is too low, this may cause the ice maker to

malfunction.

Thewatersupplytotheappli-

ancemustbethroughacold

waterpipethatcanwithstand

the operating pressure and

complies with the hygiene

regulations.

Forthis,usethestainlesssteelhosesupplied(length3m).

6. Routethemainscabletowardsthesocket.

7. Routethewaterhosetowardsthewatershut-offtap.

8. Pushtheapplianceslowlyintotherecessuntilthecompressor

mountingplatetouchestheanti-tippingbracket.

9. Fillthehosewithwaterandconnecttotheshut-offtap.

Be sure the connection is tightly arranged.

 Opentheshut-offtapandcheckthesystemforleakage.

Important!

Aftertheicemakerhasbeenswitchedon,thewater

supplysystemmustbebled.

SeethesectionBleeding the ice makerintheop-

eratinginstructions.

5. Locatethewaterhoseintotherailof

theappliancebase.

WARNING!

Do not connect the appliance to the power supply

until the installation is completed.

CAUTION!

Lay the mains cable and the water hose in such

a way that they will not be damaged when the

appliance is slid into the installation recess.

Mounting the ventilation grille

 Pulloutthebottomfreezerdrawer.

1. Removetheblueprotectionfilmfromthedustfilter

providedandinsertthefilterintoitsopening

in the plinth. Engage the filter at the

bot t o m ,p re s s d ownt heb ut t o n a n d 

clickintoplace.

3.Insertthesupportsfortheventilationgrille

ontheleftandrightsidesinthemotor

compartment.

2.Remove the locking pins of

bothsupports.Thesupports

are provided with the appli-

anceaccessorypack.

Fastening the appliance in the recess

Onceintherecess,securetheapplianceto

thebodyoftheunitusingthesecuring

plates(4x16screws).

Thenclickthecoverssup-

pliedintoplace.

Leveling the appliance

1. Adjusttheheightoftheapplianceatthefrontbytwistingthe

levelingfeet

.Usetheopen-endedspannerprovided.

Turnthespannercounterclockwisetoraisetheappliancefront

andclockwisetolowerit.

 Positionthespanneraccordingly(

2. Adjusttheheightoftheapplianceattherearbyturningthe

adjustingbolts

.Usea 1/4"boxspanner or theTorx25

wrenchprovided.

3. Rotatelevelingfeet

untilfirmlyinplaceagainstthefloor.

WARNING!

To prevent the appliance from tipping forward

the leveling feet

must have contact with

the floor.

5. Insert the locking pins to block the

supports.

6. Installtheventilationgrille.

 Thegrillehasboltsontheinside(seedetailinthedrawing

below).Theseboltsmustbeinsertedintotheholesofthe

supports.

4. Thefrontedgeofthebrackets

is flush with the front of the

ventilationgrille.

 Adjustthesupportsaccordingly.

7. Adjusttheheightoftheventilationgrille.

• Loosenthegrubscrewsatthefrontofthegrille(Allenkey

A/F2.5).

• Adjusttheventilationgrilletothedesiredheight.

• Tightenthegrubscrews.

Removing the mounting accessories from the

refrigerator door

Removethecover

andunscrewthetopandbottomattach-

mentbrackets

fromtherefrigeratordoor.Theseattachment

bracketswillbemountedontotherefrigeratordoorpanel.

Important!

The securing nuts are needed for re-mounting the pre-

assembled door panel onto the refrigerator door.

Removing the mounting accessories from the

freezer drawers

Unscrewtheattachmentbrackets

fromthefreezerdrawers.

These attachment brackets will be mounted onto the freezer

panels.

Important!

The screws are needed for re-mounting the pre-assembled

freezer panels onto the freezer drawers.

Adjusting the refrigerator door

Thelateraltiltoftherefrigeratordoorcanbeadjustedifrequired.

Undoscrews

.Adjustthelateraltiltusingthegrubscrew

(AllenkeyA/F2.5).

Adjusting the front of the drawer

Ifrequired,thefrontofthefreezerdrawerscanbeadjusted.

Transferthescrewsshownintheillustration(ontheleftandright

sidesofthefreezerdrawer)individuallytothelongslotsbelow.

Tighten the screwsinthe frontofthedrawer onceitisinthe

rightposition.

Side view of the freezer drawer

pulled out

Mounting the attachment brackets onto the door panels

1. Drawaline1041mmfromthebottomsideofthedoorpanel.

2. Drawafurtherline107.5mmfromthebottomsideofthedoorpanel.

3. Alignoneoftherefrigeratordoorattachmentbracketstothetopline,asshownintheillustrationbelow,andsecurewithatleast

6screws(4x14).

4. Alignthesecondrefrigeratordoorattachmentbrackettothebottomline,asshownintheillustrationbelow,andsecurewithat

least6screws(4x14).

5. Secureeachoftheattachmentbracketsthathavebeenremovedfromthefreezerdrawersusing3screws(4x14),asshownin

theillustrationbelow.

Refrigeratordoorpanel

Freezerdrawerpanel

fig. D

Mounting the refrigerator panel

fig. A

fig. B

fig. C

1. Screwintheadjustingpinson

theundersideoftherefrigerator

doorcompletely(fig. A).

2. Opentherefrigeratordoorandsus-

pendtherefrigeratorpanelonthetop

adjustingpins(fig. B).

3. Screwsecuringnutsontotheadjust-

ingpinsandslightlytighten.

4. Closetherefrigeratordoorandchecktheheight

ofthepanel.

5. Adjusttheheightofthe panelif necessary.

Undothesecuringnutsandusetheadjusting

pinstoadjust(fig. C).

6. Adjustthepanelhorizon-

tally(usingthelongslots

intheattachmentbracket)

(fig. D).

7. Tightenthesecuringnuts.

fig. E

fig. F

8. Removetheadjustingpins

(bottom of therefrigerator

door)untilthesetouchthe

attachmentbracket(fig. E).

9. Screwonthesecuringnutsandtighten(fig. F).

Mounting the freezer panels

1. Pulloutthetopfreezerdrawerandscrewonthepre-assembled

panel.Thesamescrewsmustbeusedasthoseusedtoscrew

ontheattachmentbrackets(3.5x13).

2. Closethefreezerdrawerandcheckthepositionofthepanel.

Adjusttheheightofthepanelbyundoingtheleftandright

screws.Tightenthescrews.

3.Pulloutthebottomfreezerdrawerandmountthepanelinthe

sameway.

4. Forbothdrawers,coverthegapbetweenthedrawerandthe

panelwiththecoverstripssupplied.Removetheprotective

filmfromthetrimandinsertintothegapatthetop.

3.5x13mm

Changing over door hinges

Doorhingesshouldonlybechangedbyatrainedexpert.

WARNING!

Do not try to change over the door hinges your-

self. The refrigerator door hinges are fitted with

strong closing springs. If the hinge accidentally

snaps shut, this can lead to serious injury.

11. Clickthetopandbottomcoversintoplace1 (fig. H)

Insertthecoverstripprovided2betweenrefrigeratordoor

andpanel.

fig. H

fig. G

10. Undothethreescrewsonthetopoftheattach-

mentbracket,adjustthedoorpanelasdisplayed

in fig. Gandthenretightenthescrews.Thesame

procedure can be carried out for the bottom

attachmentbracket.

LiebherrHausgeräteLienzGmbH*Dr.-Hans-Liebherr-Strasse1*A-9900Lienz**www.liebherr.com

Liebherr ECBN 5066 PremiumPlus Assembly And Installation Instructions

Brand: Liebherr

Model: ECBN 5066 PremiumPlus

Category: Fridges

Type: Assembly And Installation Instructions

This manual is also suitable for

Download PDF

report

Liebherr ECBN 5066 PremiumPlus Assembly And Installation Instructions

This manual is also suitable for

Liebherr ECBN 5066 PremiumPlus Assembly And Installation Instructions

Related papers

Other documents