Optimus TAS2000VOIP-W User manual

TAS 2000 VOIP

WEATHER-PROOF

VoIP

TELEPHONE SET

INSTALLATION AND

PROGRAMMING MANUAL

Tas2000Voip

Software lab

Tas2000Voip

Software lab

iii

Description ........................................................................................................................................................... v

I. Main features Tas2000Voip ............................................................................................................................... 1

1. Technical features ..................................................................................................................................... 2

Summary of the features of the telephone Tas2000Voip ......................................................................... 2

2. Factory settings ......................................................................................................................................... 3

Network configuration ........................................................................................................................... 3

Tas2000Voip's localization .................................................................................................................... 3

Configuration control of the phone ........................................................................................................ 3

Retrieving IP address of the model Tas2000Voip ................................................................................... 3

Local procedure ............................................................................................................................ 3

Remote procedure ......................................................................................................................... 3

Retrieving mac-address value of Tas2000Voip model. ........................................................................... 3

Retrieving phone number of Tas2000Voip model. ................................................................................. 3

II. Installation ....................................................................................................................................................... 4

3. Connections .............................................................................................................................................. 5

Power Supply ....................................................................................................................................... 5

Connecting Fitre amplified speaker ........................................................................................................ 5

Network connection .............................................................................................................................. 6

4. Assembly .................................................................................................................................................. 7

5. Expansion cards ........................................................................................................................................ 8

Input/Output Card ................................................................................................................................ 8

Electric features .................................................................................................................................... 8

III. Configuration .................................................................................................................................................. 9

6. Main ....................................................................................................................................................... 10

Main Page web page ........................................................................................................................... 10

Call Information web page .................................................................................................................. 11

7. Setup ...................................................................................................................................................... 12

Line web page .................................................................................................................................... 12

Login .......................................................................................................................................... 12

NAT .......................................................................................................................................... 12

RTP ............................................................................................................................................ 13

Address Book web page ...................................................................................................................... 13

Characteristics element's address book ......................................................................................... 14

Main features of elements as part of a group ................................................................................ 15

Multifunction Button web page ............................................................................................................ 16

Force Call ................................................................................................................................... 17

Call ............................................................................................................................................. 17

Function ...................................................................................................................................... 17

Advanced web page ............................................................................................................................ 18

Network configurations ............................................................................................................... 19

Busy tone timeout ....................................................................................................................... 21

Handling of the IP addresses, mac-address and account readings ................................................... 21

Handling of the web server access ............................................................................................... 22

Handling of special buttons ......................................................................................................... 22

SIP Protocol Options ................................................................................................................... 22

Preferences web page .......................................................................................................................... 23

Telephone configurations ............................................................................................................. 23

Outgoing volumes ....................................................................................................................... 26

Custom tone schema web page ............................................................................................................ 27

Echo Canceller Settings web page ....................................................................................................... 28

Software Updates web page ................................................................................................................. 29

External Devices web page .................................................................................................................. 30

Guided Procedure ........................................................................................................................ 30

Amplifier Configuration web page ....................................................................................................... 33

Tas2000Voip

iv

Configuration of the amplifier ..................................................................................................... 33

Allarms and tests configuration page. ........................................................................................... 36

Speech Test Configuration web page ................................................................................................... 40

Speech Test Configuration ........................................................................................................... 41

Speech Test ................................................................................................................................ 41

Alarm Tone Configuration ........................................................................................................... 42

Reset configuration to factory defaults ......................................................................................... 42

8. Status ...................................................................................................................................................... 43

System Information web page .............................................................................................................. 43

System Information ..................................................................................................................... 43

Kernel version ............................................................................................................................. 43

SIP Line Status ........................................................................................................................... 44

System Logs ............................................................................................................................... 44

Settings web page ............................................................................................................................... 44

Configuration Menu .................................................................................................................... 45

IV. Use ............................................................................................................................................................... 47

9. Description .............................................................................................................................................. 48

Standard interface behavior ................................................................................................................. 48

Buttons volume control ............................................................................................................... 48

Select audio device ..................................................................................................................... 48

Leds behavior ............................................................................................................................. 48

✓

button ..................................................................................................................................... 49

✗

button ...................................................................................................................................... 49

Function buttons .......................................................................................................................... 49

10. Calls handling ....................................................................................................................................... 51

Simplex Calls ...................................................................................................................................... 51

Simplex mode configuration ........................................................................................................ 51

Enable simplex functions mode ................................................................................................... 51

Disable simplex functions mode .................................................................................................. 51

Simplex functions ........................................................................................................................ 51

PTT calls ............................................................................................................................................ 51

PTT mode configuration .............................................................................................................. 52

A. Notes ............................................................................................................................................................. 53

v

Description

Tas2000Voip, industrial VoIP phone with handsfree and handset.

Tas2000Voip is a VoIP phone compatible with the SIP standard that allows voice communication over an IP network.

Tas2000Voip is specifically designed to provide the highest quality in an industrial environment. Particular attention has

been taken in optimization of the hands-free full-duplex communication.

The Tas2000Voip can have an audio output dedicated to the use of a amplified Fitre speaker that allows both to amplify

the ring tones or prerecorded voice messages from a remote location.

Tas2000Voip can make direct calls using , to which was previously associated with a number in the Address Book web

page section and a relative behavior as described in the Multifunction Button web page.

It's possible to add the generic inputs/outputs by setting up the optional I/O expansion module, with different number

of input or output (all photo-coupled). This connect to the Tas2000Voip device, which takes complete control, after the

configuration with External Devices web page. The inputs and outputs can be configured and monitored from the control

center to realize special functions such as alarms input on field, turning on lamps, turning on cameras…

Figure 1. Model Tas2000Voip views

Figure 2. Model Tas2000Voip views

Part I. Main features Tas2000Voip

2

Chapter 1. Technical features

Summary of the features of the telephone Tas2000Voip

Required supply from 12 to 57 V DC (Pw: 4 W max)

Ethernet connection 1×10/100 RJ45 (IEEE 802.3af Power Over Ethernet com-

patible)

Operating temperature -20 °C ÷ +70 °C

Environment relative humidity 20 ÷ 98% non-condensing

Protection degree IP65

Chassis Weather-proof alluminium fusion

Color Orange RAL2000

Dimensions (L×H×P) 323 × 232 × 142 mm

Auxiliary audio output

0 dB

mW

on 600 Ω

3

Chapter 2. Factory settings

Network configuration

The default configuration uses a DHCP server to configure the IP address of the VoIP device. Tas2000Voip includes a

DHCP client to get an IP address and it allows you to configure other network parameters such as Netmask, IP gateway

and DNS client. If there is no DHCP server, the terminal remains available at the fixed address 192.168.249.78: accessing

Advanced web page, it's possible to change the network settings.

To configure the Tas2000Voip it's possible to use the integrated web server by entering the IP number in the address bar

(url) of a common web browser. User voip and password voip are the default values to access the web server.

Tas2000Voip's localization

For the exact position of the model Tas2000Voip on the network, it's possible to run a test call using the SIP address

taken from Line web page: the phone will rings or, if configured in auto answer mode, will accept the call, turning on

simultaneously the LED of line.

Configuration control of the phone

By connecting the browser to the System Information web page, it's possible to check if the telephone has its lines regis-

tered on the configured SIP registrar. It is also possible to make this check with the System Monitor page of the web site

of Astro System Manager Fitre if it has been bought together with the model Tas2000Voip as part of the system. From

Settings web page it's also possible to verify the telephone current configuration.

Retrieving IP address of the model Tas2000Voip

The IP address assigned to the model Tas2000Voip can be both locally or remotely retrieved.

Local procedure

The model Tas2000Voip pronounces the IP address if the M1 button is pressed and held for the time interval configured

in the Advanced web page, as it can be seen in Handling of the addresses web page. The preset configuration includes

a 5 second timeout.

Remote procedure

This procedure can only be applied if the Tas2000Voip client DHCP is used to receive the IP address from the DHCP

server which is present in the network. In this case, to go back to the IP address list of the connected devices, it is enough

to read the list of the assigned IP addresses; normally the DHCP server could be both a router or an Astro System Manager

Fitre, in case it has been bought as a part of the system.

Retrieving mac-address value of Tas2000Voip model.

The model Tas2000Voip pronounces the mac-address holding the M2 button for the time configured in the Advanced

web page, as shown in Handling of the addresses. The default configuration provides a timeout of 5 seconds.

Retrieving phone number of Tas2000Voip model.

The model Tas2000Voip pronounces its phone number holding the M3 for the time configured in the Advanced web page,

as shown in Handling of the addresses. The default configuration provides a timeout of 5 seconds.

Part II. Installation

5

Chapter 3. Connections

Power Supply

The Tas2000Voip can be supplied both using the proper connector as shown in Figure 3.1, “Connections” or through the

mains connection by means of a switch POE (Power Over Ethernet), in accordance with the IEEE 802.3af standard: these

two modes can coexist. The outer supply inlet is protected against the reversed polarities.

Figure 3.1. Connections

Connecting Fitre amplified speaker

When connected with a Fitre amplified speaker, external power is required and the value of the nominal voltage shall be

referred to the model of the speaker which is using. If the power supply is also needed for the Tas2000Voip its value of

voltage must lie in the range of values visible in technical features table. The five-pole connector M1 visible in the figure

Figure 3.2, “Connections Dettails”, allows to connect a Fitre amplified speaker. From left are the two poles of power, the

ground connection and the two contacts of the balanced signal.

Figure 3.2. Connections Dettails

Connections

6

Network connection

The LAN network should be connected to the proper RJ45 connector on the main card as in Figure 3.1, “Connections”.

7

Chapter 4. Assembly

Figure 4.1. Front view

Figure 4.2. Dimensions, side view

8

Chapter 5. Expansion cards

Input/Output Card

Input/Output card can control 2 relay outlets as well as 3 optical isolated inlets. There are three connections on each relay,

also providing the normally closed connection, as it can be seen in Figure 5.1, “Input/Output card connection ”.

Figure 5.1. Input/Output card connection

Electric features

Input Polarized inlet activation, as it can be seen in Figure 5.1,

“Input/Output card connection ” 9 to 50 V DC voltage.

Output

Voltage max 250 V AC

Electric current max 2 A

Electric power max 62,5 VA (30 W DC)

Part III. Configuration

Tas2000Voip has a web server for an easy configuration of the terminal. If the terminal is connected to a network with

DHCP, it can be immediately accessed with a browser after its startup. The user's voip and the password voip are the default

parameters to access the web server. All pages are available using the menu on the left.

10

Chapter 6. Main

Main Page web page

This is the main page which can be accessed after the login and it includes three different fields:

1. a list of all the possible lines

2. an interface to call another device

3. a report of the ongoing calls

On the board Tas2000Voip is possible to configure different lines at the same time and using the list in Figure 6.1, “Line

to use” it is possible to choose the line that would be used for outgoing calls.

Figure 6.1. Line to use

From the interface in Figure 6.2, “Form for calls by web” it is possible to call another device. To make this call, you

should enter the number (extension) and select a proxy from the drop down menu, or enter both the number and the proxy

according to the string ext@proxy. Pressing on the Call button, the card Tas2000Voip would try to contact the required

number.To end the ongoing call, press on the Stop button.

Figure 6.2. Form for calls by web

If there is a call, as described in Figure 6.3, “Active calls” are shown essential information about:

Direction Shows if it is an incoming or outgoing call

State Shows the state of the call

From Shows the caller

To Shows who receive the call

At the end of the call, the information shall appended to a historic table available by accessing the Call Information web

page

Figure 6.3. Active calls

Main

11

Call Information web page

Figure 6.4. Call History

This page shows the history of the calls dialed or received on the Tas2000Voip. As it can be seen in Figure 6.4, “Call

History” the calls are listed according to the date and time they were made, from the oldest to the most recent, and for

each call is shown:

• the call direction

In Tas2000Voip incoming call

Out Tas2000Voip outcoming call

• the date and time of the call

• the duration

• the calling party

• the receiving party

The call history is updated after each call.

12

Chapter 7. Setup

Line web page

The pages for the lines configuration are divided into three different sections:

Login SIP login informations

NAT NAT line setting

RTP RTPline setting

On the board Tas2000Voip there are many 8 line pages allowing to configure a line SIP and its account in a SIP registrar.

Login

Figure 7.1. Login form

Displayname Mnemonic name

1

Account Alphanumeric filed representing the SIP registrar/proxy account.

2

Password Password configured SIP on the registrar/proxy

3

SIP registrar Registrar/proxy IP or url address where the account should be registered.

Proposed Expiry Time interval indicating the account registration validity. When this validity ex-

pires, a new registration request will be sent.

When removing a SIP line, it is recommended to open the main page and change the line used for the outgoing line, if

necessary.

NAT

This page allows the NAT server to be specified, in order to mask the subnet without beign disconnected to the outlet

of the subnet itself.

Figure 7.2. NAT Form

1

not used for more practicality. SIP

2

For example Astro System Manager Fitre

3

In Astro System Manager Fitre it comes as a default parameter xxx

Setup

13

Active Indicates wether the NAT is active or not.

NAT server (IP-addr) Indicates the NAT IP address.

RTP

From this page, it is possible to select the audio configurations which are compatible with the terminal and the application

order of preference. For example, it is possible to select an audio configuration requiring a reduced consumption of network

reources, that is with a low bit rate. This could affect the audio quality, which normally requires a longer band. In this table,

different audio configurations are shown in a decreseasing order. In the first column on the left, there are the selection

buttons; after having selected an audio configuration, it is possible to move it up (UP button) and down (DOWN button)

or it can be disabled (DISABLE button).

Figure 7.3. RTP form

Address Book web page

Through this page it is possible to manage a column or a group of numbers which can be saved, in order to speed up

the call procedure.

Setup

14

Characteristics element's address book

Figure 7.4. Address book element's configuration

Creating elements of address book requires the following parameters:

Memo name

It allows an unambiguous identification of each element. It is not possible to have more than one element with the same

name. In case you need to change the name of an element contained in the column, you should remove such an element

and create a new one with the desired name.

Sip address

This field contains the number to call, which may be configured as follows:

• extension

• extension@host

• sip:extension@host

• sip:@address

• address

Line to use

Contains the useful information to identify the line to be used to make a call.

This should be as follows:

Page is loading ...

Optimus TAS2000VOIP-W User manual

Optimus TAS2000VOIP-W User manual

Related papers

Other documents