B&B Electronics 9POP4 Quick start guide

B&B Electronics
Brand
B&B Electronics
Model
9POP4
Category
Serial converters/repeaters/isolators
Type
Quick start guide
Documentation Number –p/n 9093R1 9POP4-0712qsg
©2010 B&B Electronics Manufacturing Company
C
C
e
e
r
r
t
t
i
i
f
f
i
i
c
c
a
a
t
t
i
i
o
o
n
n
s
s
• FCC Class B
• CE
o EN 55022: 2006 + A1:2007 Class A Emissions
o EN 61000-6-1: 2007 Generic Standards for
Residential, Commercial and Light-Industrial
Environments
o EN 61000-4-2: 2008 Electro-Static Discharge
(ESD)
o EN 61000-4-3: 2006 Radiated Field Immunity
(RFI)
o EN 61000-4-4: 2004 Electrical Fast Transients-
Burst (EFT)
o EN61000-4-5: Ed2, 2005 (Surge)
o EN 61000-4-6: 2005 Conducted Immunity
C
C
h
h
e
e
c
c
k
k
f
f
o
o
r
r
A
A
l
l
l
l
R
R
e
e
q
q
u
u
i
i
r
r
e
e
d
d
H
H
a
a
r
r
d
d
w
w
a
a
r
r
e
e
9POP4 RS-232 Optical Isolator
This Quick Start Guide
12VDC Wall Power Supply (sold separately).
Recommended Power Supplies:
o US – 232PS
o UK – PS1UK-1000
o EU – PS1EU-1000
Put
Quick Start Guide
9POP4
Optically Isolated RS-232
Repeater
D
D
B
B
9
9
P
P
i
i
n
n
-
-
o
o
u
u
t
t
1. DTE stands for Data Terminal
Equipment: these include Computers,
PLC's, and most devices which are not
used to extend communications. Think
COMPUTER for DTE.
2. DCE stands for Data Communications
Equipment: these includes devices
intended to plug directly into a DTE
port, Modems and devices that extend
communications like a modem, such
as RS-422, RS-485, or Fiber Optic
converters or Radio Modems. Think
MODEM for DCE.
3. On the DCE (female) side, Pins 1, 4,
and 6 are tied together internally.
4. On the DTE (Male) side, Pins 4 and 6
are tied together internally.
2
1
I
I
n
n
f
f
o
o
r
r
m
m
a
a
t
t
i
i
o
o
n
n
–
–
C
C
o
o
n
n
n
n
e
e
c
c
t
t
o
o
r
r
s
s
Connectors
A
DB9 Female – Data Communications Equipment
(DCE)
A
DB9 Male – Data Terminal Equipment (DTE)
C
Power – 12 VDC Jack, 2.5 mm Center Positive
Pin
Signal
DTE
1
DCD
Input
2
RD
Input
3
TD
Output
4
DTR
Output
5
GND
---
6
DSR
Input
7
RTS
Output
8
CTS
Input
9
RI
Input
3
4
Documentation Number –p/n 9093R1 9POP4-0712qsg
©2010 B&B Electronics Manufacturing Company
5
W
W
i
i
r
r
i
i
n
n
g
g
E
E
x
x
a
a
m
m
p
p
l
l
e
e
P
P
o
o
w
w
e
e
r
r
1. The two sides of the isolator are
powered from a single +12VDC power
supply and maintain isolation. This
powering configuration allows the
device to be run in any system with
only a single supply, regardless of the
power levels on the RS-232 ports.
2. In order to maintain the required
isolation, use the recommended
power supply. Using an unregulated
power supply may negate the
isolation.
3. Recommended Power Supplies:
a. US – 232PS
b. UK – PS1UK-1000
c. EU – PS1EU-1000
L
L
o
o
o
o
p
p
b
b
a
a
c
c
k
k
T
T
e
e
s
s
t
t
Use a DB9 Female to DB9 Male cable to connect a
PC to the DCE port.
(Recommended) Connect a DB9 Female to DB9
Female cable to the DTE port.
On the DTE Port, jumper pin 2 to 3 and pin 7 to 8 on
the female end of the cable. This loops TD to RD and
CTS to RTS.
Using hyper terminal or similar program, connect to
the appropriate COM port (remember to set the baud
rate to 9600).Turn off hyper terminal local echo
Transmit data. The same data should be returned.
6
7
  • Page 1 1
  • Page 2 2

B&B Electronics 9POP4 Quick start guide

B&B Electronics
Brand
B&B Electronics
Model
9POP4
Category
Serial converters/repeaters/isolators
Type
Quick start guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents