ADTRAN MX408 is an ethernet and TDM Pseudowire gateway. It provides the interfaces and switching between a 10/100 Ethernet or GigE network port to four client 10/100 Ethernet ports and eight DSX-1 TDM ports. The MX408 provides pseudowire connections between the network and client DSX-1 ports and Ethernet switching between the network and client 10/100 Ethernet ports. The device has 18 rear panel wire-wrap posts for Alarm Relays and Aux Inputs. It has a DB-9 craft port (RS-232) and a module slot for future applications.
ADTRAN MX408 is an ethernet and TDM Pseudowire gateway. It provides the interfaces and switching between a 10/100 Ethernet or GigE network port to four client 10/100 Ethernet ports and eight DSX-1 TDM ports. The MX408 provides pseudowire connections between the network and client DSX-1 ports and Ethernet switching between the network and client 10/100 Ethernet ports. The device has 18 rear panel wire-wrap posts for Alarm Relays and Aux Inputs. It has a DB-9 craft port (RS-232) and a module slot for future applications.
For more information, refer to the MX408e Command Line Interface and Application Guide (P/N 61189608L1-1)
available online at www.adtran.com
.
1. Attach mounting brackets to the side of the MX408e in the correct orientation for either rackmount or
wallmount using the two screws provided for each bracket.
♦ To rackmount the unit, use the appropriate rack type screws to mount the MX408e into the rack.
CAUTION: Care should be taken to not upset the stability of the equipment rack during installation.
♦ To wallmount the unit, secure the MX408e to the wall with appropriate screws.
2. Connect the frame ground from the frame ground lug on the upper right rear panel (see figure on reverse
page) of the MX408e to the equipment rack grounding screw or other appropriate grounding connection.
3. Make power connections to the MX408e.
NOTE: A readily accessible disconnect device, such as a rackmount fuse and alarm panel that is suitably
approved and rated should be incorporated into the fixed wiring.
Connect to a reliably grounded –48 VDC or ±24 VDC source which is electrically isolated from the
AC source.
The branch circuit overcurrent protection should be a 2 amp, slow-blow fuse or circuit breaker.
3a. Determine which fuse pairs are to supply power to the MX408e.
3b. Remove the fuses from the A and B slots for the pair.
3c. Connect
RET A, PWR A, RET B, and PWR B to the power connector. PWR refers to respective
–48 VDC or ±24 VDC power sources, while
RET refers to respective returns.
4. Apply power and check voltages.
WARNING: Installing fuses in the fuse and alarm panel at this stage provides power to the MX408e pins
and connectors on the rear panel and inside the MX408e. Exercise caution to avoid
electrical shock.
4a. Install appropriate fuses (2 amp slow-blow) in the slots in the fuse and alarm panel that services
the MX408e.
4b. Using a voltmeter, verify that the operating voltage is within the specifications for A or B power
feeds. For more information, refer to “Operational Specifications”.
5. Connect the CRIT (critical), MAJOR, and MINOR alarm leads from the fuse and alarm panel to the
Common (
C), Normally Open (NO), and Normally Closed (NC) wire-wrap terminals on the MX408e
rear panel as required.
6. Connect the auxiliary inputs, labeled
AUX INPUTS, as required. The MX408e auxiliary inputs connect
as follows:
♦ AUX INPUT terminals 1 and 2 connect to Alarm 1
♦ AUX INPUT terminals 3 and 4 connect to Alarm 2
♦ AUX INPUT terminals 5 and 6 connect to Alarm 3
♦ AUX INPUT terminals 7 and 8 connect to Alarm 4
♦ AUX INPUT terminal 9 is not connected
GENERAL
The MX408e Pseudowire Gateway (MX408e) provides the requisite interfaces and switching between a
10/100 Ethernet or GigE network port to four client 10/100 Ethernet ports and eight DSX-1 TDM ports. The
MX408e provides pseudowire connections between the network and client DSX-1 ports and Ethernet
switching between the network and client 10/100 Ethernet ports.
Network ports consist of an RJ-45 10/100 Ethernet jack and an Small Form-factor Pluggable (SFP) cage for
a GigE SFP module. The four client 10/100 Ethernet ports are equipped with RJ-45 jacks. The eight DSX-1
ports are RJ-48C jacks supporting 4-wire DSX-1s (Transmit Tip, Transmit Ring, Receive Tip, and Receive
Ring).
The MX408e front panel (see figure above) also provides a module slot for future applications. In the event
that a module is not deployed in the MX408e, a blank panel (P/N 1189699L1) is installed.
Features
The MX408e has the following features:
SFPs
CAUTION: Due to compliance certification requirements, use only SFPs supplied by ADTRAN with the
MX408e. ADTRAN cannot certify system integrity with other SFPs. To ensure compatibility,
refer to the documentation provided with each SFP.
The MX408e is not factory-equipped with SFPs. Recommended SFPs are listed in the following table.
INSTALLATION
After unpacking the MX408e, inspect it for damage. If damage is noted, file a claim with the carrier and then
contact ADTRAN. For more information, refer to the warranty statement on the reverse side of this job aid.
Installation and Power Turn-up
To wallmount or rackmount the MX408e, perform the following steps:
♦ GigE copper/fiber SFP or 10/100 Ethernet
Network ports
♦ Four client 10/100 Ethernet ports
♦ Eight client DSX-1 short-haul, intrabuilding ports
♦ DB-9 craft port (RS-232)
♦ Front panel LEDs
♦ Module slot for future applications
♦ Dual –48 VDC (±24 VDC) power inputs
♦ 18 rear panel wire-wrap posts for Alarm Relays
and Aux Inputs
ADTRAN P/N Description
1184561P1 1000Base-LX, 1310 nm, single mode, 2 fiber operation, 10 km maximum optical distance
1184561P3 1000Base-SX, 850 nm, multi-mode, 2 fiber operation, 700 meter maximum optical distance
1184561P4 1000Base-T, copper, 4 wire, 100 meter over CAT5 UTP cable
Document P/N: 61189608L1-22A
Issue Date: 0706
*61189608L1-22A*
ACT ALM
ACO
MODULE
1234 56781234
CRAFT
10/100
MODULE
GE
DSX-1
MX408e
1189608L1
10/100
NETWORK
CLEI: C0M7V00E_ _
Product Number: 1189608L1
MX408e Pseudowire Gateway
PRICING AND AVAILABILITY 800.827.0807
TECH SUPPORT 800.726.8663
RETURN FOR REPAIR 256.963.8722
www.adtran.com
61189608L1-22A
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not meet its published specifications or fails while in service.
Warranty information can be found online at www.adtran.com/warranty
.
©2007 ADTRAN, Inc.
All Rights Reserved.
Front Panel LEDs
Label Status Description
NETWORK
(GE & 10/100)
{
z
z
Off
Green
Amber
No link
Link is up
Transmit or Receive activity
10/100
(Clients 1 - 4)
{
z
z
Off
Green
Amber
No link
Link is up
Transmit or Receive activity
DSX-1 (1 - 8) {
z
z
2
z
2
2
Off
Green
Amber
Flashing Amber
Red
Flashing Red
Flashing Red 1 second
Port is disabled
Port is enabled and in normal operation
Locally originated test in progress
Remotely originated test in progress
Non-critical DSX-1 defect in progress (for example, AIS,
RAI)
Critical DSX-1 defect (non-critical system defect; for
example, LOS, LOF)
Single code violation or burst of code violations just
occurred
ACT
z
z/z
z
z/z
z
2
Green
Green/Amber (alternating)
Amber
Red/Amber (alternating)
Red
Flashing Red
Normal operation
Normal operation and console open
Software update in progress
Self-test failed and console open
Self-test failed
Card has failed
ALM
z
z
2
z
2
Green
Amber
Flashing Amber
Red
Flashing Red
No critical, major, or minor alarms
Active acknowledged non-critical alarm
Active acknowledged critical alarm
Major or minor alarm in progress
Critical alarm in progress
MODULE
{
z
z
2
Off
Green
Red
Flashing Red
Module not installed
Module normal operation
Module alarm
Module failed
CONNECT AND LOGIN TO SYSTEM
Connect to the front panel RS-232, DB-9 connector labeled CRAFT to log on and provision the MX408e by
way of VT100 terminal or VT100 terminal emulation software such as HyperTerminal or ProComm Plus.
CRAFT port defaults are as follows:
♦ Data Rate: Auto (up to 115.2 kbps)
♦ Asynchronous Data Format: 8-data bits, no parity, 1-stop bit, and no flow control
Press E
NTER to activate the CLI.
The MX408e can also be accessed via Telnet through an Ethernet interface.
10/100 port (Ethernet) defaults are as follows:
♦ IP Address: 192.168.100.1
♦ Subnet Mask: 255.255.0.0
♦ Default Gateway: 192.168.1.1
NOTE: The default username and password are “ADMIN” and “PASSWORD” in all capital letters.
OPERATIONAL SPECIFICATIONS
The MX408e operational specifications are as follows:
♦ Operates from A or B input voltage power feeds
♦ –48 VDC systems: –42 VDC to –60 VDC
♦ –24 VDC systems: –22 VDC to –27 VDC
♦ +24 VDC systems: +22 VDC to +27 VDC
♦ Maximum Current and Power
♦ 1 amp @ 24 VDC; 500 mA @ 48 VDC
♦ Less than 24 watts dissipated
♦ Extended operating temperature range: –40°C to +65°C
♦ Storage temperature range: –40°C to +85°C
♦ Relative humidity: 95 percent maximum, noncondensing
COMPLIANCE NOTICE
Refer to the MX408e Pseudowire Gateway Compliance Notice (P/N 61189608L1-17) for detailed
compliance information.
MX408e Pseudowire Gateway
C A U T I O N
C A U T I O N
!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
-
1
-
2
ADTRAN MX408 is an ethernet and TDM Pseudowire gateway. It provides the interfaces and switching between a 10/100 Ethernet or GigE network port to four client 10/100 Ethernet ports and eight DSX-1 TDM ports. The MX408 provides pseudowire connections between the network and client DSX-1 ports and Ethernet switching between the network and client 10/100 Ethernet ports. The device has 18 rear panel wire-wrap posts for Alarm Relays and Aux Inputs. It has a DB-9 craft port (RS-232) and a module slot for future applications.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ADTRAN MX408 Job Aid
-
-
-
-
-
-
-
-
-