Leviton Wire-Free Multi-Location Dimmer Control User manual

Brand: Leviton

Model: Wire-Free Multi-Location Dimmer Control

Type: User manual

This manual is also suitable for

1 2 3 4

65 7 8

Quick tip: Up to three Decora

Smart Anywhere Companions

can be paired to a Decora

Smart Wi-Fi 2nd Gen device.

• Pair the Anywhere Dimmer

Companion with a Decora

Smart D26HD Dimmer for

additional on/off and dim/

bright control where you need

it most like at the base of a

staircase or end of a hallway.

• Pair the Anywhere Dimmer

Companion with a Decora Smart

D23LP Mini Plug-In Dimmer to add

on/off and dim/bright control of

ﬂoor lamps to any indoor

wall surface.

Getting Started Guide

Cat. No. DAWDC

ANYWHERE DIMMER COMPANION

Wire-free multi-location control

See the complete line of My LevitonTM app compatible

dimmers, switches, plug-ins, and controllers at

leviton.com/decorasmart

Features

At a glance

Ease of use

The Decora Smart Anywhere

Dimmer Companion pairs directly

with your Decora Smart Wi-Fi 2nd

Generation Dimmer or Mini Plug-In

Dimmer to provide additional

lighting control wherever you need

it. Mount it directly on your wall

surface or at an existing wall box—

no wiring required.

The Anywhere Dimmer Companion

looks right at home with your other

Decora Smart Wi-Fi devices and

features familiar on/off and dim/

bright controls.

Anywhere Companion devices do

not require Wi-Fi or an app

for setup.

DI-000-DAWDC-02A

Mounting on a wall surface:

1. Select a clear wall surface within a 50 ft.

range of the primary Decora Smart Wi-Fi

2nd Gen device.

Installing at the wall box:

To install in a standard NEMA electrical box in

single-gang or multi-gang installations:

1. Take note of the TOP marking on the

reverse side of the Anywhere Companion.

2. Turn off power at the circuit

breaker during installation.

Line up the Anywhere

Companion with the screw holes

in the desired location at the

wall box. Make sure the location

is within a 50 ft. range of the

primary Decora Smart Wi-Fi

2nd Gen device.

3. Screw in the Anywhere

Companion to the wall box

via the innermost screw

holes using the included

wall box screws. Tighten the

screws until snug. Do not

overtighten screws.

3. Take note of the TOP and WALL

SIDE markings on the back of

the device and gently afﬁx the

Anywhere Companion to the

wall surface using the adhesive

tape. Make sure the

device is securely held

in place and level.

2. Place included adhesive tape on the reverse

side of the Anywhere Companion; align the

top and bottom pieces of tape with the

corner markings molded into the base.

Installation Installation

Welcome

If at any time you are unsure about the installation

process, contact Leviton technical support or

consult an electrician.

If at any time you are unsure about the installation

process, contact Leviton technical support or

consult an electrician.

NOTE: Installation in a metal wall box can weaken the RF

signal and reduce wireless range.

If you need help...

ONLINE

decorasmartsupport.leviton.com

CHAT

www.leviton.com/contact

[email protected]

CALL

1-800-824-3005 (USA)

1-800-405-5320 (Canada)

Easy Wi-Fi lighting

control for the

whole home

CHAT

www.leviton.com/contact

CALL

1-800-824-3005 (USA)

1-800-405-5320 (Canada)

ONLINE

decorasmartsupport.leviton.com

[email protected]

We are here to help

Leviton Manufacturing Co., Inc.

201 North Service Road, Melville, NY 11747

Speciﬁcations subject to change at any time without notice.

WARNING: TO AVOID FIRE, SHOCK OR DEATH,

turn off power at the circuit breaker.

For more information and features visit:

leviton.com/decorasmart

• Place it anywhere you need additional

lighting control:

• Create 3-way/multi-way control with

no wiring.

• Mount directly to your wall surface or

install at an existing wall box where a

traveler wire may not be present.

• Classic Decora style.

• No Wi-Fi or app required for setup.

• Fits Leviton Decora standard and screwless

wallplates (single and multi-gang).

• 5 year battery life. Replaceable CR2025

batteries included.

• Pair up to three Anywhere Companions with

a Decora Smart Wi-Fi 2nd Gen device.

Dim/bright bar

Tap to manually adjust light levels.

Decora Rocker

• Press the top to turn the light ON.

• Press the bottom to turn the light OFF.

• Double press the top to turn ON at

max brightness.

Mounting Base

• Easily mount to the wall surface or

install in a single or multi-gang

wall box.

Status LED

• Shows pairing and

connectivity status.

• Off during normal operation.

Your Anywhere Dimmer

Companion works with:

• Decora Smart Wi-Fi 2nd Generation devices:

• Visit Leviton.com/decorasmart for product

compatibility updates.

DAWDC

Anywhere Dimmer

Companion

D26HD

Dimmer

D23LP

Mini Plug-In

Dimmer Back View

Front View

SPECIFICATIONS

Operating Temp 0°C - 40°C (32°F - 104°F)

Operating Humidity 0 - 90% non-condensing

Storage Temperature Range -10°C - 85°C

Batteries CR2025 (2)

Network 2.4GHz

Range 50 ft.

NOTE:

• Anywhere Companion devices are battery powered and

pair with Wi-Fi 2nd Generation devices using wireless RF

technology for communication.

• Anywhere Companions do not connect directly to the

load/lights. A line powered primary Wi-Fi 2nd Gen Device or

Mini Plug-in is required (sold separately).

• Do not use with metal wallplates.

• For indoor use only.

Matching Decora style

• Shallow product depth matches

your in-wall Decora devices

when installed for a

seamless look.

• Fits Leviton Decora standard

and screwless wallplates.

TO LIGHT

D26HD

DAWDC

D23LP

WEB VERSION

9 10 11 12

1413 15 16

What to do if...

Attach the wallplate

Safety ﬁrst

Limited 2 Year Warranty &

Exclusions

The Anywhere Companion will not pair to the primary Decora

Smart Wi-Fi device:

• Make sure you are pairing to a Decora Smart Wi-Fi 2

Gen device and

that both the Anywhere Companion and primary are in range and in

pairing mode.

How do I know if I have a primary Decora Smart Wi-Fi 2

Gen

device?

• Make sure your 5 digit part number starts with D2. To locate the part

number: For an in-wall device, remove the wall plate and ﬁnd the 5

digit part number in the upper right hand corner of the strap. For a

plug-in, the 5 digit part number is on the reverse side of the device.

The Anywhere Companion has an intermittent connection to its

primary Decora Smart Wi-Fi

Gen device:

• Make sure the Anywhere Companion is within a 50 ft. range of the

primary device.

• This product is not designed to transmit through exterior surfaces.

Environmental factors can impact wireless range. Before installing,

consider materials such as concrete or steel reinforced ﬂoors,

ceilings, walls, masonry, cinderblock, and reinforced materials such

as plaster and stucco that may interfere with range.

• Check to make sure you do not have a low battery; see page 15 for

how to check the battery level using the Diagnostic LED.

Can I control multiple Decora Smart Wi-Fi 2

gen devices with a

single Anywhere Companion?

• No, however up to three Anywhere Companions can be paired to a

Decora Smart Wi-Fi 2

Gen device.

How do I clean my device?

• To clean use a damp cloth with mild soap. DO NOT use disinfecting

products, including foggers, sprays or other types of atomized

cleaning agents.

For Leviton’s limited product warranty, go to www.leviton.com. For a printed copy of the

warranty, call 1-800-824-3005.

FOR CANADA ONLY

For warranty information and/or product returns, residents of Canada should contact

Leviton in writing at Leviton Manufacturing of Canada ULC to the attention of the Quality

Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by

telephone at 1 800 405-5320.

FCC COMPLIANCE STATEMENT

The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (i.) This device may not cause harmful interference (ii.) This

device must accept any interference received, including interference that may cause

undesired operation. Any changes or modiﬁcations not expressly approved by Leviton

could void the user’s authority to operate this equipment. This equipment has been tested

and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC CAUTION

Any changes or modiﬁcations not expressly approved by Leviton Manufacturing Co., Inc.,

could void the user’s authority to operate the equipment.

FCC SUPPLIER’S DECLARATION OF CONFORMITY

Model DAWDC – Anywhere Dimmer Companion is manufactured by Leviton Manufacturing

Co., Inc. 201 N. Service Road, Melville, NY 11747. www.leviton.com This device complies

with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

IC STATEMENT

This device complies with Industry Canada license-exempt RSS standard(s). Operation is

subject to the following two conditions: (1) this device may not cause interference, and (2)

this device must accept any interference, including interference that may cause undesired

operation of the device.

RF EXPOSURE AND CO-LOCATION

To comply with FCC OET Bulletin 65 and ISED RF exposure limits for general population

and uncontrolled exposure, this device shall be installed and operated with a minimum

distance of 7.9 inches (20 cm) between the radiator and your body. Also, must not be co-

located or operated in conjunction with any other antenna or transmitter.

Decora and Decora Smart are the registered trademarks of Leviton Manufacturing Co., Inc.,

registered in the U.S., Canada, Mexico and China.

Use herein of other third party trademarks, service marks, trade names, brand names and/or

product names are for informational purposes only, are/may be the trademarks of their respective

owners; such use is not meant to imply afﬁliation, sponsorship, or endorsement. No part of this

document may be reproduced, transmitted or transcribed without the express written permission

of Leviton Manufacturing Co., Inc.

Status LED

Diagnostic LED

If the Anywhere Companion is not functioning as expected the

Status LED can be used as a diagnostic tool. Press the top rocker

for at least 2 seconds but less than 7 seconds, then release.

The device should blink a diagnostic code for two seconds,

If your Anywhere Companion is not performing as expected,

visit leviton.com/decorasmart or contact Leviton’s technical

services team.

COLOR ACTIVITY STATUS

Not lit N/A Normal Operation.

Green Solid Button has been pressed (normal

feedback) or device pairing conﬁrmation.

Green Fast Blink Device is in Pairing Mode.

Amber Slow Blink Device has lost connection to its primary

Decora Smart Wi-Fi 2nd Gen Device.

Red Slow Blink Low battery warning.

COLO R STATUS

Green Normal operation; connected to a primary device.

Amber Not connected to a primary device.

Red Low battery warning.

Factory default reset

WARNINGS:

• This product is to be installed and/or used in accordance with electrical

codes and regulations.

• For indoor use only.

• If you are unsure about any part of these instructions, consult an electrician.

CAUTIONS:

• Save this instruction sheet. It contains important technical data along

with testing and troubleshooting information which will be useful after

installation is complete.

• Leviton Decora Smart Anywhere Companions rely on wireless

RF communication.

• Decora Smart Anywhere Companion devices use 2 CR2025 coin cell

batteries ONLY. Do not use a rechargeable battery. Use of an improper

battery may cause damage to the device.

Test control

Powering up

The Anywhere Companion comes with

two CR2025 batteries already installed.

Pairing

Changing the batteries

1. Hold the top of the Decora Rocker for 14 seconds.

2. After the ﬁrst 7 seconds the status light will turn AMBER.

Continue to hold.

3. After 7 more seconds, the status light will quickly ﬂash

RED/AMBER.

4. Release the top of the Decora Rocker and the device will

reset. This will remove all pairing associations.

1. To power up the Anywhere

Companion, place your ﬁnger

on the indent in the base.

2. Find the indent in the base

and use your ﬁnger to open

the device by rotating the

frame gently to the left

using the hinge.

1. Remove the wallplate (if

using a screwless wallplate,

the mounting bracket does

not need to be removed).

2. Open the device by rotating

the frame gently to the left

using the hinge.

3. Grasp each pull tab

by the circular portion

and pull up to remove.

Remove both pull tabs

(each battery). This will

activate power and put

the Anywhere Companion

into Pairing Mode.

The Status LED will

begin ﬂashing GREEN.

3. Place ﬁnger in gap as

marked by arrows.

4. Close the device by rotating the frame gently to the right

using the hinge.

5. Replace with CR2025

batteries only.

4. Gently lift batteries out of

holder. While lifting batteries,

press out on battery holder

tabs as needed to

release batteries.

5. Press down ﬁrmly in the corners

until the device snaps closed.

6. Close the device by rotating the

frame gently to the right using

the hinge.

7. Press down ﬁrmly in the corners

until the device snaps closed.

8. Snap on the wallplate.

Powering up

(continued)

Changing the batteries

(continued)

Follow the below steps to pair the Anywhere Companion with

its primary Decora Smart Wi-Fi 2nd Gen device.

NOTES:

• The primary Decora Smart Wi-Fi 2nd Gen device pairs

one Anywhere Companion at a time. To pair up to three

Anywhere Companions, place the primary Decora Smart

Wi-Fi 2nd Gen device back into Pairing Mode and restart the

process with the next Anywhere Companion.

Activate and pair one Anywhere Companion at a time.

1. Make sure the Anywhere Companion is in pairing mode

and its Status LED is blinking green.

NOTE: If not paired after 10 minutes, the Anywhere

Companion will enter a standby state to preserve battery life.

To place it back into pairing mode, single press the top rocker

5 times. The Status LED will begin ﬂashing GREEN.

2. Place the primary Decora Smart Wi-Fi 2nd Gen Device into

Pairing Mode:

• For in-wall devices press the top rocker 5 times.

• For plug-in devices press the control button 5 times.

• The Status LED will ﬂash green/amber when in

pairing mode.

3. The Decora Smart Wi-Fi 2nd Gen device will automatically

pair to the Anywhere Companion in pairing mode in

wireless RF range. Once paired, the Anywhere Companion’s

Status LED will brieﬂy turn solid GREEN to show a

successful connection.

1. Attach the screwless wallplate

mounting bracket by screwing into

the outermost screw holes.

Tighten screws until snug—do

not overtighten.

2. Snap on the Decora screwless

wallplate.

NOTE: Anywhere Companions are

compatible with Leviton Decora

standard and screwless wallplates in

single and multi gang conﬁgurations.

Congratulations! You have successfully setup

your Anywhere Dimmer Companion!

Additional self-help resources can be found at

leviton.com/decorasmart

If at any time you are unsure or need help contact

Leviton support or visit leviton.com/decorasmart

Once the Anywhere Companion

device has been installed and

successfully paired to its primary

Decora Smart Wi-Fi 2nd Gen

device, test control by pressing the

Anywhere Companion’s rocker ON

and OFF to toggle the load.

WEB VERSION

Leviton Wire-Free Multi-Location Dimmer Control User manual

Brand: Leviton

Model: Wire-Free Multi-Location Dimmer Control

Type: User manual

This manual is also suitable for

Download PDF

report

Leviton Wire-Free Multi-Location Dimmer Control User manual

This manual is also suitable for

Leviton Wire-Free Multi-Location Dimmer Control User manual

Related papers

Other documents