Astria Fireplaces H8707 Installation guide
- Category
- Fireplaces
- Type
- Installation guide
This manual is also suitable for
NOTE: DIAGRAMS AND ILLUSTRATIONS NOT TO SCALE
WARNING
HOT GLASS WILL CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL COOLED.
NEVER ALLOW CHILDREN TO TOUCH GLASS.
•Install only when fireplace is OFF and COLD.
•Fireplace surfaces get EXTREMELY HOT!
•The glass on the front of the fireplace reaches EXTREMELY HIGH
temperatures and can cause severe burns if touched. Even after the
gas is turned off, fireplace surfaces remain extremely hot.
• Keep children away from an operating fireplace. Closely supervise children in
any room where a fireplace is operating to prevent contact with glass.
CAUTION
RISK OF PERSONAL INJURY OR PROPERTY DAMAGE.
•Do NOT abuse glass doors by striking or slamming shut.
•Never operate fireplace with glass door assembly removed.
•Handle glass door assembly with extreme care. Replace
damaged glass door assembly with approved replacement
assembly only.
•Use only media approved for use with these fireplaces (as
applicable). Failure to use approved media may result in sooting,
delayed ignition, or other improper fireplace operation, and may
void the warranty.
NOTICE
•READ ALL STEPS BEFORE STARTING INSTALLATION.
•LEAVE THESE INSTRUCTIONS WITH THE APPLIANCE.
•All warnings, precautions, and instructions in the Installation
Instructions and Care and Operation Instructions provided with the
appliance also apply to these instructions.
•If you encounter any problems, need clarification of these
instructions, or are not qualified to properly install this kit, contact
your local distributor or dealer.
GENERAL INFORMATION
This document contains installation instructions for the fireplace
log kit used with Envy direct‑vent gas fireplaces. This procedure
should be followed during initial appliance setup and when
re‑installing the log set after the annual cleaning and inspection
cycles.
Use care to prevent breakage when handling the logs. Once
heated by the fireplace, these logs are very fragile.
DO NOT install the logs until the appliance installation has been
completed, the gas line has been connected and tested for leaks,
and the initial burner operation has been verified.
NOTE: Turn OFF the appliance and allow it to completely cool
berfore installing this kit.
INSTALLATION INSTRUCTIONS FOR LOG KITS
FOR USE WITH ENVY SERIES DIRECT-VENT GAS FIREPLACES
[FIREPLACE MODELS ENVY35TEN, ENVY40TEN, AND ENVY45TEN]
P/N 900005-04
Rev. A 10/2014
HEARTH PRODUCTS
KITS AND ACCESSORIES
LOG PLACEMENT GUIDE
FOR TRADITIONAL DIRECT VENT GAS FIREPLACES
P900005-04
REQUIRED TOOLS
• Safety Glasses
• Protective Work Gloves
KIT CONTENTS
1. Rear Log
2. Bottom Left Log
3. Bottom Right Log
4. Front Log
5. Top Right Log
6. Top Left Log
• Log Placement Guide
Figure 1: Log Set
1
2
6
3
5
4
Catalog number for the entire set:
35 in.—H8707,
40 in.—H8708,
45 in.—H8824
CAUTION
INSTALL ONLY WHEN FIREPLACE IS OFF AND COLD!
FIREBOX ACCESS
1. Use the fireplace remote control to ensure the fireplace is OFF.
2. Remove the top louver.
3. Remove the left and right side finish trim gap fillers.
4. Remove the surround trim assembly by detaching it at the
top of the fireplace and lifting it 1 in. to disengage the side
tabs, then pulling it away from the fireplace exposing the
front glass door.
5. Locate the four (4) spring‑loaded latches; two above and two
below the enclosure. Release the lower latches, by pulling
each handle out and down to unhook it from the glass door.
Lightly press against the door, to hold it in position, while
releasing the two upper latches. Carefully grip the glass door
at both the top and bottom, and remove from the fireplace.
Retain the door in a secure location for later reinstallation.
NOTE: Envy log
placement is highly
sensitive. Follow
directions carefully.
INNOVATIVEHEARTHPRODUCTS•SIGNATURESERIESDIRECT-VENTGASFIREPLACES•ENVYTRADITIONAL•INSTALLATIONINSTRUCTIONS
6. Apply a small amount of pressure against the door to hold it
in position. Then, release the two upper latches.
7. Carefully grip the glass door at the top and bottom, and
remove it from the fireplace.
NOTE: Place the glass door in a secure location where it will
not be damaged until reinstrallation.
INSTALL THE LOGS AND DECORATIVE VOLCANIC STONE
NOTE: Turn OFF all electricity to the appliance before
installing volcanic stone, and logs.
NOTE: The log set and burner are designed to provide an
artistic, asymmetrical fire. The fire does not burn in the left rear
quarter of the log set.
1. Align the two holes in the bottom of Log 1 over the two tabs
at the rear of the burner (Figure 2).
Figure 2: Placing Logs 1 and 2
2
1
2. Hold Log 1 in position while placing Log 2 on the burner and
resting it against the alignment notch in Log 1 (Figure 2).
3. Place Log 3 in position with the base aligned in the burner
surface (Figure 3).
Figure 3: Placing Log 3
3
4. Insert the left end of Log 4 under Log 3 and position the right end
of Log 4 in the notch on the top, right end of Log 3 (Figure 4).
Figure 4: Placing Log 4
4
5. Ensure all logs are properly positioned on the surface of the
burner and interlocked with each other (Figure 4).
6. Place Log 5 in position in the notches on the upper right
portions of Logs 1 and 3 (Figure 5).
Figure 5: Placing Logs 5 and 6
5
6
7. Place Log 6 in position in the notches near the left ends of
Logs 2 and 3 (Figure 5).
8. If Installed, position and secure the andirons.
9. Place the volcanic stone generously in front of the burner on
the ramped sub‑floor. In an artistic manner, blend the volcanic
stone with the glowing embers in front of the log set, to
simulate a diminishing ember bed.
FIREPLACE REASSEMBLY
1. With an ammonia‑free glass cleaner and soft, non‑abrasive cloth,
remove smudges from the inner surface of the glass door.
2. Carefully position the glass door in front of the firebox
with the gasket properly seated, and hook the two top door
latches over the door frame. Then, hook the two bottom
door latches over the door frame.
3. Locate the surround trim assembly mounting slots on the
left and right sides of the firebox. Align the surround trim
assembly with the mounting slots and press in and down to
lower the surround into position. Reinstall the left and right
side finish trim gap fillers.
4. With an ammonia‑free glass cleaner and a soft, non‑abrasive
cloth, remove fingerprints and smudges from the front
surface of the glass door and the surround trim assembly.
P/N 900005-04 Rev. A 10/2014
1508 Elm Hill Pike, Suite 108
Nashville, TN 37210
IHP.US.com
Innovative Hearth Products reserves the right
to make changes at any time, without notice,
in design, materials, specifications, prices and
also to discontinue colors, styles, and products.
Consult your local distributor for fireplace
code information Printed in U.S.A. © 2014
Innovative Hearth Products, LLC .
P900005-04
-
1
-
2
Astria Fireplaces H8707 Installation guide
- Category
- Fireplaces
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Astria Fireplaces Madison Park CD 27 Installation guide
-
-
-
-
-
-
-
-
Other documents
-
Astria Envy40 Series Installation And Operation Instructions Manual
-
Superior Fireplaces DRT63ST Operating instructions
-
-
-
-
-
-
-
Superior DRT2033 Installation And Operation Instructions Manual
-
