NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
INSTALLATION INSTRUCTIONS FOR FRAMING STANDOFF AND VENT GASKET
FOR USE WITH SIGNATURE® SERIES ENVY AND ENVY CD DIRECT-VENT GAS FIREPLACES
[FIREPLACE MODELS ENVY35TEN, ENVYCD35TEN, ENVY40TEN, ENVYCD40TEN, ENVY45TEN, ENVYCD45TEN]
P/N 900005-07
Rev. A 10/2014
HEARTH PRODUCTS
KITS AND ACCESSORIES
FRAMING STANDOFF AND VENT GASKET
CAUTION
RISK OF PERSONAL INJURY OR PROPERTY DAMAGE.
•Never operate fireplace without liner panels installed.
•These appliances are NOT approved for operation without
liner panels.
•Do NOT abuse glass doors by striking or slamming shut.
•Never operate fireplace with glass door assembly removed.
•Handle glass door assembly with extreme care. Replace
damaged glass door assembly with approved replacement
assembly only.
•Use only media approved for use with these fireplaces (as
applicable). Failure to use approved media may result in sooting,
delayed ignition, or other improper fireplace operation, and may
void the warranty.
NOTICE
•READ ALL STEPS BEFORE STARTING INSTALLATION.
•LEAVE THESE INSTRUCTIONS WITH THE APPLIANCE.
•All warnings, precautions, and instructions in the Installation
Instructions and Care and Operation Instructions provided with the
appliance also apply to these instructions.
•If you encounter any problems, need clarification of these
instructions, or are not qualified to properly install this kit, contact
your local distributor or dealer.
GENERAL INFORMATION
This kit contains all the necessary components to assemble and
install the ENVY and ENVY CD framing standoff and the top vent
rope gasket.
The information provided must be used in conjunction with the
Care and Operation Instructions. Please read the instructions
completely before performing the procedures detailed in
this document.
REQUIRED TOOLS
• 5/16 in. Hex-head nut driver
KIT CONTENTS
• Left side framing
standoff (1)
• Right side framing
standoff (1)
• Center support (1)
• 5/16 in. Hex head
screws (8)
• Rope gasket (1)
FRAMING STANDOFF KIT INSTALLATION INSTRUCTIONS
1. Bend both standoffs at the designated places to prepare the
components for installation (Figure 1).
Figure 1: Bending the framing standoffs
2. Align the right side of the framing standoff with the right side
of the fireplace (Figure 2). Secure the standoff with two (2)
of the included 5/16 in. screws in the holes closest the side
of the fireplace.
WARNING
HOT GLASS WILL CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL COOLED.
NEVER ALLOW CHILDREN TO TOUCH GLASS.
•Install only when fireplace is OFF and COLD.
•Fireplace surfaces get EXTREMELY HOT!
•The glass on the front of the fireplace reaches EXTREMELY HIGH
temperatures and can cause severe burns if touched. Even after the
gas is turned off, fireplace surfaces remain extremely hot.
•Keep children away from an operating fireplace. Closely supervise
children in any room where a fireplace is operating to prevent
contact with glass.
P900005-07
INNOVATIVEHEARTHPRODUCTS•SIGNATURE®SERIESDIRECT-VENTGASFIREPLACES•ENVY/ENVYCD35/40/45TEN•INSTALLATIONINSTRUCTIONS
P/N 900005-07 Rev. A 10/2014
1508 Elm Hill Pike, Suite 108
Nashville, TN 37210
IHP.US.com
Innovative Hearth Products reserves the right
to make changes at any time, without notice,
in design, materials, specifications, prices and
also to discontinue colors, styles, and products.
Consult your local distributor for fireplace
code information Printed in U.S.A. © 2014
Innovative Hearth Products, LLC.
P900005-07
Figure 2: Attaching the right side framing standoff
Screws
3. Align the left side of the framing standoff with the left side of
the fireplace (Figure 3). Secure the standoff with two (2) of
the included 5/16 in. screws in the holes closest the side of
the fireplace.
NOTE: The ends of the framing standoffs will overlap.
Figure 3: Attaching the left side framing standoff
Screws
4. Position the center support as shown (Figure 4), with
the larger screw holes oriented to the bottom. Secure
with two (2) of the included 5/16 in. screws in the top
and two (2) 5/16 in. screws in the bottom of the center
support.
Figure 4: Installing the center support
Screws
Screws
TOP VENT ROPE GASKET INSTALLATION INSTRUCTIONS
1. Slide the rope gasket over the top vent component and
position it snugly against the apppliance (Figure 5).
Figure 5: Installing the rope gasket
Rope Gasket
AFTER INSTALLING THE KIT
1. Reinstall the media/logs (if applicable) and the glass door.
2. Refer to the Installation Instructions (P/N 900005-00)
for information regarding turning ON the gas supply,
reconnecting the power supply at the circuit breaker, and
additional framing information.
-
1
-
2
Astria Fireplaces Envy CD Instruction Sheet
- Type
- Instruction Sheet
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Astria Envy40 Series Installation And Operation Instructions Manual
-
Superior Fireplaces DRC3545DEP-B Operating instructions
-
-
-
-
-
-
White Mountain Hearth Boulevard Direct-Vent Linear Contemporary & Traditional Fireplace (DVLL41FP, DVTL41BP) Owner's manual
-
-
