Astria Fireplaces Envy Installation guide

Brand: Astria Fireplaces

Model: Envy

Category: Fireplaces

Type: Installation guide

This manual is also suitable for

H8707

Astria Fireplaces Envy offers a realistic and captivating flame experience, fueled by natural gas or propane for your convenience. With its traditional direct vent design, you can enjoy the warmth and ambiance of a real fire without the hassle of wood or ashes. The included log placement guide ensures proper positioning for optimal performance. Safety features like protective work gloves and warnings about hot glass surfaces provide peace of mind during installation and use. Experience the beauty and comfort of Astria Fireplaces Envy in your own home.

NOTE: DIAGRAMS AND ILLUSTRATIONS NOT TO SCALE

WARNING

HOT GLASS WILL CAUSE BURNS.

DO NOT TOUCH GLASS UNTIL COOLED.

NEVER ALLOW CHILDREN TO TOUCH GLASS.

•Install only when fireplace is OFF and COLD.

•Fireplace surfaces get EXTREMELY HOT!

•The glass on the front of the fireplace reaches EXTREMELY HIGH

temperatures and can cause severe burns if touched. Even after the

gas is turned off, fireplace surfaces remain extremely hot.

• Keep children away from an operating fireplace. Closely supervise children in

any room where a fireplace is operating to prevent contact with glass.

CAUTION

RISK OF PERSONAL INJURY OR PROPERTY DAMAGE.

•Do NOT abuse glass doors by striking or slamming shut.

•Never operate fireplace with glass door assembly removed.

•Handle glass door assembly with extreme care. Replace

damaged glass door assembly with approved replacement

assembly only.

•Use only media approved for use with these fireplaces (as

applicable). Failure to use approved media may result in sooting,

delayed ignition, or other improper fireplace operation, and may

void the warranty.

NOTICE

•READ ALL STEPS BEFORE STARTING INSTALLATION.

•LEAVE THESE INSTRUCTIONS WITH THE APPLIANCE.

•All warnings, precautions, and instructions in the Installation

Instructions and Care and Operation Instructions provided with the

appliance also apply to these instructions.

•If you encounter any problems, need clarification of these

instructions, or are not qualified to properly install this kit, contact

your local distributor or dealer.

GENERAL INFORMATION

This document contains installation instructions for the ﬁreplace

log kit used with Envy direct‑vent gas ﬁreplaces. This procedure

should be followed during initial appliance setup and when

re‑installing the log set after the annual cleaning and inspection

cycles.

Use care to prevent breakage when handling the logs. Once

heated by the ﬁreplace, these logs are very fragile.

DO NOT install the logs until the appliance installation has been

completed, the gas line has been connected and tested for leaks,

and the initial burner operation has been veriﬁed.

NOTE: Turn OFF the appliance and allow it to completely cool

berfore installing this kit.

INSTALLATION INSTRUCTIONS FOR LOG KITS

FOR USE WITH ENVY SERIES DIRECT-VENT GAS FIREPLACES

[FIREPLACE MODELS ENVY35TEN, ENVY40TEN, AND ENVY45TEN]

P/N 900005-04

Rev. A 10/2014

HEARTH PRODUCTS

KITS AND ACCESSORIES

LOG PLACEMENT GUIDE

FOR TRADITIONAL DIRECT VENT GAS FIREPLACES

P900005-04

REQUIRED TOOLS

• Safety Glasses

• Protective Work Gloves

KIT CONTENTS

1. Rear Log

2. Bottom Left Log

3. Bottom Right Log

4. Front Log

5. Top Right Log

6. Top Left Log

• Log Placement Guide

Figure 1: Log Set

Catalog number for the entire set:

35 in.—H8707,

40 in.—H8708,

45 in.—H8824

CAUTION

INSTALL ONLY WHEN FIREPLACE IS OFF AND COLD!

FIREBOX ACCESS

1. Use the ﬁreplace remote control to ensure the ﬁreplace is OFF.

2. Remove the top louver.

3. Remove the left and right side ﬁnish trim gap ﬁllers.

4. Remove the surround trim assembly by detaching it at the

top of the ﬁreplace and lifting it 1 in. to disengage the side

tabs, then pulling it away from the ﬁreplace exposing the

front glass door.

5. Locate the four (4) spring‑loaded latches; two above and two

below the enclosure. Release the lower latches, by pulling

each handle out and down to unhook it from the glass door.

Lightly press against the door, to hold it in position, while

releasing the two upper latches. Carefully grip the glass door

at both the top and bottom, and remove from the ﬁreplace.

Retain the door in a secure location for later reinstallation.

NOTE: Envy log

placement is highly

sensitive. Follow

directions carefully.

INNOVATIVEHEARTHPRODUCTS•SIGNATURESERIESDIRECT-VENTGASFIREPLACES•ENVYTRADITIONAL•INSTALLATIONINSTRUCTIONS

6. Apply a small amount of pressure against the door to hold it

in position. Then, release the two upper latches.

7. Carefully grip the glass door at the top and bottom, and

remove it from the ﬁreplace.

NOTE: Place the glass door in a secure location where it will

not be damaged until reinstrallation.

INSTALL THE LOGS AND DECORATIVE VOLCANIC STONE

NOTE: Turn OFF all electricity to the appliance before

installing volcanic stone, and logs.

NOTE: The log set and burner are designed to provide an

artistic, asymmetrical ﬁre. The ﬁre does not burn in the left rear

quarter of the log set.

1. Align the two holes in the bottom of Log 1 over the two tabs

at the rear of the burner (Figure 2).

Figure 2: Placing Logs 1 and 2

2. Hold Log 1 in position while placing Log 2 on the burner and

resting it against the alignment notch in Log 1 (Figure 2).

3. Place Log 3 in position with the base aligned in the burner

surface (Figure 3).

Figure 3: Placing Log 3

4. Insert the left end of Log 4 under Log 3 and position the right end

of Log 4 in the notch on the top, right end of Log 3 (Figure 4).

Figure 4: Placing Log 4

5. Ensure all logs are properly positioned on the surface of the

burner and interlocked with each other (Figure 4).

6. Place Log 5 in position in the notches on the upper right

portions of Logs 1 and 3 (Figure 5).

Figure 5: Placing Logs 5 and 6

7. Place Log 6 in position in the notches near the left ends of

Logs 2 and 3 (Figure 5).

8. If Installed, position and secure the andirons.

9. Place the volcanic stone generously in front of the burner on

the ramped sub‑ﬂoor. In an artistic manner, blend the volcanic

stone with the glowing embers in front of the log set, to

simulate a diminishing ember bed.

FIREPLACE REASSEMBLY

1. With an ammonia‑free glass cleaner and soft, non‑abrasive cloth,

remove smudges from the inner surface of the glass door.

2. Carefully position the glass door in front of the ﬁrebox

with the gasket properly seated, and hook the two top door

latches over the door frame. Then, hook the two bottom

door latches over the door frame.

3. Locate the surround trim assembly mounting slots on the

left and right sides of the ﬁrebox. Align the surround trim

assembly with the mounting slots and press in and down to

lower the surround into position. Reinstall the left and right

side ﬁnish trim gap ﬁllers.

4. With an ammonia‑free glass cleaner and a soft, non‑abrasive

cloth, remove ﬁngerprints and smudges from the front

surface of the glass door and the surround trim assembly.

P/N 900005-04 Rev. A 10/2014

1508 Elm Hill Pike, Suite 108

Nashville, TN 37210

IHP.US.com

Innovative Hearth Products reserves the right

to make changes at any time, without notice,

in design, materials, speciﬁcations, prices and

also to discontinue colors, styles, and products.

Consult your local distributor for ﬁreplace

Innovative Hearth Products, LLC .

P900005-04

Astria Fireplaces Envy Installation guide

Brand: Astria Fireplaces

Model: Envy

Category: Fireplaces

Type: Installation guide

This manual is also suitable for

H8707

Download PDF

report

Astria Fireplaces Envy Installation guide

This manual is also suitable for

Astria Fireplaces Envy Installation guide

Related papers

Other documents