Western Blade, A-Frame, Quadrant & Lift Channel (Compact) Installation guide

Western
Brand
Western
Model
Blade, A-Frame, Quadrant & Lift Channel (Compact)
Type
Installation guide

This manual is also suitable for

Western Blade, A-Frame, Quadrant & Lift Channel (Compact)

This device is a versatile and durable attachment for your vehicle, designed to help you tackle a variety of tasks, including snow removal, landscaping, and material handling.

  • Blade: The blade is made of high-strength steel and is designed to withstand the toughest conditions. It can be angled and raised or lowered to meet your specific needs.
  • A-Frame: The A-Frame is made of sturdy steel and provides a solid foundation for the blade. It can be attached to your vehicle's frame using hitch pins.
  • Quadrant: The quadrant is made of cast iron and provides a smooth and precise motion for the blade. It is attached to the A-Frame and the blade.

Western Blade, A-Frame, Quadrant & Lift Channel (Compact)

This device is a versatile and durable attachment for your vehicle, designed to help you tackle a variety of tasks, including snow removal, landscaping, and material handling.

  • Blade: The blade is made of high-strength steel and is designed to withstand the toughest conditions. It can be angled and raised or lowered to meet your specific needs.
  • A-Frame: The A-Frame is made of sturdy steel and provides a solid foundation for the blade. It can be attached to your vehicle's frame using hitch pins.
  • Quadrant: The quadrant is made of cast iron and provides a smooth and precise motion for the blade. It is attached to the A-Frame and the blade.
A DIVISION OF DOUGLAS DYNAMICS. INC.
SUB-COMPACT
COMPACT
STANDARD
Blade, A-Frame
Quadrant & Lift Channel
INSTALLATION ILLUSTRATION
& INSTRUCTIONS
WESTERN PRODUCTS
7777 NORTH 73RD STREET
P.O. BOX 23045
MIL W AUKEE, WISCONSIN 53223
HOOK CHAIN
HERE~
~ LIFT CHANNEL
~r
r L 93083 RIVE J USE ON SUB COMPACT (80860),
SHORT (80198) . MEDIUM (8022)
l VCOTTER PIN A-FRAME BOXES
i 93083 RIVET J SEe NOTE 1
SUB COMPACT 81
~ ~ PIN MEDIUM A-FRAME
. OR
i iI
i
¡",GROOVE PIN) SEE NOTE 2
.. L93086 RIV SHORT A-FRAME
"- SUB COMPACTA-FRAME
. QUADRANT TO BLADE
Asemble the quadrant to the blade with the quadrant lugs straddling the center ribs. Secure with%" x 3" bolts and locknuts. DO
NOT.collaae lugi inward by ovrthtening bolt.
SPRINGS ANDÈYEBOLTS
Install one nut half way down on each eyebolt. Hoo the springs to the eyebolt and quadrant brackets. Place the eyebolts through
the holes in the top angle of the blade and tighten by installng a second nut above the angle. Tighten only until the coils bein to
separate, (instruction sheet should pass betwn the seond and third coils), and lock in place using the nut below the angle.
A-FRAME TO QUADRANT
. AS$emble the A-Frame to the quadrant, poitioning the straight quadrant angle beeen the formed nos plate and angle of the A-
Frame, and the curv quadrant angle under the retainer bar welded to the rear of the formed nose plate. Attach using %" x 2" bolt
and nut on Sub-Compact units or 3A" x 2~lI bolt and nut on Compact and Standard units. Tighten just enough to permit free pivotal
motion. .
HYDRA-TURN~CYUNDER ATTACHMENT
Attach the two Hydra-Turr" cylindrs to the brackets on eiter side of the A-Frame and Quadrant. Attach ram end of cylinders to
quadrant with furnishe rivets inserted from top don and secured with cotter pins.
The threaded cylinder port in base end of cylindr should be outwrd.
NOTE 1: Installations using Sub Compa A8tQ Box 6050 or Medium A8tQBo 6022 with Hydra-Tur~,attach base end of
cylinders to A-Frame with rivets inserted from top down and secured with cotter pi..
NOTE 2: Installations using Short A&Q Box 60198 with Hydra- Tur~, attach base end of cylinder to A-Frame with rivets insered
from bottom upward and secured with groove pi..
A-FRAME TO MOUNT
Couple the A-Frame to the mount spreader frame lugs using %" x 43.4" hitch pinson Sub-Compa units or 1" x 3~" hitch pins on
Compact and Standard units. Secure hitch pins with hairpin cotters.
NOTE 3: Selec hole in A-Frame lugs so bottom of A-Frame is parallel to road. Cut off lugs above selected hoes (cut per inset aboe).
LIFT CHANNEl
Assemble the lift channel to the upper U -bracket of the tift assembly with the 3.4" x 3~"bolt and locknut. Tighten to permit free pivotal
motion.
CHAIN TO A-FRAME AND LIFT CHANNEL
Place the chain beeen retainer bar lugs and secure using %" x 2%" bolt and locnut. With hydraulic cylinder collapsed pull the
chain tight and hook it to the lift channel. After it is hooked it wil have the correc amount of slack for blade "float".
Raise, lowr and angle the plow, check oil level and refil to top with automatic transmission fluid.
Form No. 13178-811 Printed in U.S.A
  • Page 1 1

Western Blade, A-Frame, Quadrant & Lift Channel (Compact) Installation guide

Western
Brand
Western
Model
Blade, A-Frame, Quadrant & Lift Channel (Compact)
Type
Installation guide
This manual is also suitable for

Western Blade, A-Frame, Quadrant & Lift Channel (Compact)

This device is a versatile and durable attachment for your vehicle, designed to help you tackle a variety of tasks, including snow removal, landscaping, and material handling.

  • Blade: The blade is made of high-strength steel and is designed to withstand the toughest conditions. It can be angled and raised or lowered to meet your specific needs.
  • A-Frame: The A-Frame is made of sturdy steel and provides a solid foundation for the blade. It can be attached to your vehicle's frame using hitch pins.
  • Quadrant: The quadrant is made of cast iron and provides a smooth and precise motion for the blade. It is attached to the A-Frame and the blade.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents