Zanussi ZBB47460DA User manual

Brand: Zanussi

Model: ZBB47460DA

Category: Fridges

Type: User manual

User manual 2

Kasutusjuhend 16

Lietošanas instrukcija 30

Naudojimo instrukcija 44

Инструкция по

эксплуатации

Інструкція 75

Fridge-Freezer

Külmik-sügavkülmuti

Ledusskapis-saldētava

Šaldytuvas-šaldiklis

Холодильник-морозильник

ZBB47460DA

Contents

Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2

Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4

First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6

Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6

Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ 7

Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8

What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9

Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11

Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11

Environmental concerns _ _ _ _ _ _ _ _ _ _ _ 15

Subject to change without notice.

Safety instructions

In the interest of your safety and to ensure the

correct use, before installing and first using the

appliance, read this user manual carefully, in-

cluding its hints and warnings. To avoid unnec-

essary mistakes and accidents, it is important to

ensure that all people using the appliance are

thoroughly familiar with its operation and safety

features. Save these instructions and make sure

that they remain with the appliance if it is moved

or sold, so that everyone using it through its life

will be properly informed on appliance use and

safety.

For the safety of life and property keep the pre-

cautions of these user's instructions as the man-

ufacturer is not responsible for damages caused

by omission.

Children and vulnerable people safety

• This appliance is not intended for use by per-

sons (including children) with reduced physi-

cal, sensory or mental capabilities, or lack of

experience and knowledge, unless they have

been given supervision or instruction con-

cerning use of the appliance by a person re-

sponsible for their safety.

Children should be supervised to ensure that

they do not play with the appliance.

• Keep all packaging well away from children.

There is risk of suffocation.

• If you are discarding the appliance pull the

plug out of the socket, cut the connection ca-

ble (as close to the appliance as you can)

and remove the door to prevent playing chil-

dren to suffer electric shock or to close them-

selves into it.

• If this appliance featuring magnetic door

seals is to replace an older appliance having

a spring lock (latch) on the door or lid, be

sure to make that spring lock unusable before

you discard the old appliance. This will pre-

vent it from becoming a death trap for a child.

General safety

Warning!

Keep ventilation openings, in the appliance en-

closure or in the built-in structure, clear of ob-

struction.

• The appliance is intended for keeping food-

stuff and/or beverages in a normal household

and similar applications such as:

– staff kitchen areas in shops, offices and

other working environments;

– farm houses and by clients in hotels, mo-

tels and other residential type environ-

ments;

– bed and breakfast type environments;

– catering and similar non-retail applications.

• Do not use a mechanical device or any artifi-

cial means to speed up the thawing process.

• Do not use other electrical appliances (such

as ice cream makers) inside of refrigerating

appliances, unless they are approved for this

purpose by the manufacturer.

• Do not damage the refrigerant circuit.

• The refrigerant isobutane (R600a) is con-

tained within the refrigerant circuit of the ap-

pliance, a natural gas with a high level of envi-

ronmental compatibility, which is nevertheless

flammable.

During transportation and installation of the

appliance, be certain that none of the compo-

nents of the refrigerant circuit become dam-

aged.

www.zanussi.com

If the refrigerant circuit should become dam-

aged:

– avoid open flames and sources of ignition

– thoroughly ventilate the room in which the

appliance is situated

• It is dangerous to alter the specifications or

modify this product in any way. Any damage

to the cord may cause a short-circuit, fire

and/or electric shock.

Warning! Any electrical component (pow-

er cord, plug, compressor) must be re-

placed by a certified service agent or qualified

service personnel to avoid hazard.

1. Power cord must not be lengthened.

2. Make sure that the power plug is not

squashed or damaged by the back of the

appliance. A squashed or damaged pow-

er plug may overheat and cause a fire.

3. Make sure that you can come to the

mains plug of the appliance.

4. Do not pull the mains cable.

5. If the power plug socket is loose, do not

insert the power plug. There is a risk of

electric shock or fire.

6. You must not operate the appliance with-

out the lamp cover (if foreseen) of interior

lighting.

• This appliance is heavy. Care should be taken

when moving it.

• Do not remove nor touch items from the

freezer compartment if your hands are damp/

wet, as this could cause skin abrasions or

frost/freezer burns.

• Avoid prolonged exposure of the appliance to

direct sunlight.

• Bulb lamps (if foreseen) used in this appli-

ance are special purpose lamps selected for

household appliances use only. They are not

suitable for household room illumination.

Daily Use

• Do not put hot pot on the plastic parts in the

appliance.

• Do not store flammable gas and liquid in the

appliance, because they may explode.

• Do not place food products directly against

the air outlet on the rear wall. (If the appliance

is Frost Free)

• Frozen food must not be re-frozen once it has

been thawed out.

• Store pre-packed frozen food in accordance

with the frozen food manufacturer's instruc-

tions.

• Appliance's manufacturers storage recom-

mendations should be strictly adhered to. Re-

fer to relevant instructions.

• Do not place carbonated or fizzy drinks in the

freezer compartment as it creates pressure

on the container, which may cause it to ex-

plode, resulting in damage to the appliance.

• Ice lollies can cause frost burns if consumed

straight from the appliance.

Care and cleaning

• Before maintenance, switch off the appliance

and disconnect the mains plug from the

mains socket.

• Do not clean the appliance with metal ob-

jects.

• Do not use sharp objects to remove frost

from the appliance. Use a plastic scraper.

• Regularly examine the drain in the refrigerator

for defrosted water. If necessary, clean the

drain. If the drain is blocked, water will collect

in the bottom of the appliance.

Installation

Important! For electrical connection carefully

follow the instructions given in specific

paragraphs.

• Unpack the appliance and check if there are

damages on it. Do not connect the appliance

if it is damaged. Report possible damages

immediately to the place you bought it. In that

case retain packing.

• It is advisable to wait at least four hours be-

fore connecting the appliance to allow the oil

to flow back in the compressor.

• Adequate air circulation should be around the

appliance, lacking this leads to overheating.

To achieve sufficient ventilation follow the in-

structions relevant to installation.

www.zanussi.com

• Wherever possible the back of the product

should be against a wall to avoid touching or

catching warm parts (compressor, condens-

er) to prevent possible burn.

• The appliance must not be located close to

radiators or cookers.

• Make sure that the mains plug is accessible

after the installation of the appliance.

• Connect to potable water supply only (If a

water connection is foreseen).

Service

• Any electrical work required to do the servic-

ing of the appliance should be carried out by

a qualified electrician or competent person.

• This product must be serviced by an author-

ized Service Centre, and only genuine spare

parts must be used.

Environment Protection

This appliance does not contain gasses

which could damage the ozone layer, in ei-

ther its refrigerant circuit or insulation materials.

The appliance shall not be discarded together

with the urban refuse and rubbish. The insula-

tion foam contains flammable gases: the appli-

ance shall be disposed according to the appli-

cable regulations to obtain from your local au-

thorities. Avoid damaging the cooling unit, espe-

cially at the rear near the heat exchanger. The

materials used on this appliance marked by the

symbol

are recyclable.

Control panel

Freezer Control panel

1 2 3 5 6 7 8 94

1. Pilot light

2. ON/OFF switch

3. Temperature regulator (warmest)

4. Temperature indicator

5. Temperature regulator (coldest)

6. Alarm light

7. Alarm reset switch

8. Action Freeze light

9. Action Freeze switch

Important!

When the doors are closed the freezer control

panel is ON.

Switching on

Insert the plug into the wall socket.

Press the ON/OFF switch .

The Pilot Light will light up.

Switching off

The freezer is shut off by pressing the ON/OFF

switch until the Pilot light and the Temperature

indicator switched off.

Temperature regulation

The temperature can be adjusted between

-15°C and -24°C.

By pressing the Temperature regulators , the

current temperature setting flashes on the Tem-

perature indicator. It is possible to modify the

setting temperature only with flashed indicator.

To set a warmer temperature, press warmest

Temperature regulator . To set a colder temper-

ature, press coldest Temperature regulator. The

Temperature indicator displays the newly selec-

ted temperature for a few seconds and then

shows again the inside compartment tempera-

ture.

The newly selected-temperature must be

reached after 24 hours.

www.zanussi.com

Caution! During the stability period by the

first starting the temperature displayed can

not correspond to the setting temperature.

Temperature indicator

During normal functioning the Temperature indi-

cator shows the temperature inside the freezer.

Important! Difference between the

temperature displayed and temperature setting

is normal. Especially when:

• a new setting has recently been selected.

• the door has been left open for a long time.

• warm food has been placed in the compart-

ment.

Excessive temperature alarm

In the event of an abnormal temperature rise in-

side the freezer (e.g. power cut) Alarm light will

start to flash and a buzzer will sound.

After the temperature has returned to normal,

the Alarm light will continue to flash, although

the buzzer has stopped.

When the Alarm reset switch is pressed, the

warmest temperature reached in the compart-

ment flashes on the Temperature indicator .

If the power has been off for a long time, frozen

food should be consumed as quickly as possi-

ble, or cooked and then re-frozen.

Action Freeze function

You can activate the Action Freeze function by

pressing the Action Freeze switch.

The Action Freeze light will light up.

When this function is on, SP is shown on the

dispay .

Important! This function stops automatically

after 52 hours.

It is possible to deactivate the function at any

time by pressing Action Freeze switch. The Ac-

tion Freeze light will switch off.

Fridge Control panel

1 2 3 5 6 74

1. Pilot light

2. ON/OFF switch

3. Temperature regulator (warmest)

4. Temperature indicator

5. Temperature regulator (coldest)

6. Action Cool light

7. Action Cool switch

Switching on

Insert the plug into the wall socket.

Press the ON/OFF switch .

The Pilot Light will light up.

Switching off

The fridge is shut off by pressing the ON/OFF

switch until the Pilot light and the Temperature

indicator switched off.

Temperature regulation

The temperature can be adjusted between

+2°C and +8°C.

By pressing the Temperature regulators, the

current temperature setting flashes on the Tem-

perature indicator. It is possible to modify the

setting temperature only with flashed indicator.

To set a warmer temperature, press warmest

Temperature regulator. To set a colder tempera-

ture, press coldest Temperature regulator. The

Temperature indicator displays the newly selec-

ted temperature for a few seconds and then

shows again the inside compartment tempera-

ture.

The newly selected-temperature must be

reached after 24 hours.

www.zanussi.com

Caution! During the stability period by the

first starting the temperature displayed can

not correspond to the setting temperature.

During this time it is possible that the

temperature displayed is lower than the setting

temperature.

Temperature indicator

During normal functioning the Temperature indi-

cator shows the temperature inside the fridge.

Important! Difference between the

temperature displayed and temperature setting

is normal. Especially when:

• a new setting has recently been selected.

• the door has been left open for a long time.

• warm food has been placed in the compart-

ment.

Action Cool function

The maximum performance is obtained by set-

ting the Action Coolfunction. It’s recommended

when loading large quantities of food.

You can activate the Action Cool function by

pressing the Action Cool switch.

The Action Cool light will light up.

Important! The internal temperature goes

down to +2°C.

After about 6 hours the Action Cool function

switches off automatically.

First use

Cleaning the interior

Before using the appliance for the first time,

wash the interior and all internal accessories

with lukewarm water and some neutral soap so

as to remove the typical smell of a brand-new

product, then dry thoroughly.

Important! Do not use detergents or abrasive

powders, as these will damage the finish.

Daily use

Freezing fresh food

The freezer compartment is suitable for freezing

fresh food and storing frozen and deep-frozen

food for a long time.

Place the fresh food to be frozen in the left

compartments, and, once frozen, moved to the

storage baskets.

The maximum amount of food that can be frozen

in 24 hours is specified on the rating plate, a

label located on the inside of the appliance.

The freezing process lasts 24 hours: during this

period do not add other food to be frozen.

www.zanussi.com

Important! When use the Auto Freeze

function:

about 6

hours before

Introducing small quantities of fresh

food (about 5 kg)

about 24

hours before

Introducing the maximum quantity of

food (see rating plate)

not needed Introducing frozen food

not needed Introducing small quantities of fresh

food daily 2 kg maximum

Storage of frozen food

When first starting-up or after a period out of

use, before putting the products in the compart-

ment let the appliance run at least 2 hours on

the higher setting.

Important! In the event of accidental

defrosting, for example due to a power failure, if

the power has been off for longer that the value

shown in the technical characteristics chart

under "rising time", the defrosted food must be

consumed quickly or cooked immediately and

then re-frozen (after cooling).

Ice-cube production

This appliance is equipped with one or more

trays for the production of ice-cubes. Fill these

trays with water, then put them in the freezer

compartment.

Important! Do not use metallic instruments to

remove the trays from the freezer.

Thawing

Deep-frozen or frozen food, prior to being used,

can be thawed in the refrigerator compartment

or at room temperature, depending on the time

available for this operation.

Small pieces may even be cooked still frozen,

directly from the freezer: in this case, cooking

will take longer.

Movable shelves

The walls of the re-

frigerator are equip-

ped with a series of

runners so that the

shelves can be posi-

tioned as desired.

Fridge Doors

For proper opening and closing, it is advisable

to act on both doors simultaneously (as shown

in the figure).

Helpful hints and tips

Hints for fresh food refrigeration

To obtain the best performance:

• do not store warm food or evaporating liquids

in the refrigerator

• do cover or wrap the food, particularly if it has

a strong flavour

• position food so that air can circulate freely

around it

Hints for refrigeration

Useful hints:

Meat (all types) : wrap in polythene bags and

place on the glass shelf above the vegetable

drawer.

www.zanussi.com

For safety, store in this way only one or two

days at the most.

Cooked foods, cold dishes, etc..: these should

be covered and may be placed on any shelf.

Fruit and vegetables: these should be thorough-

ly cleaned and placed in the special drawer(s)

provided.

Butter and cheese: these should be placed in

special airtight containers or wrapped in alumi-

nium foil or polythene bags to exclude as much

air as possible.

Milk bottles: these should have a cap and

should be stored in the bottle rack on the door.

Bananas, potatoes, onions and garlic, if not

packed, must not be kept in the refrigerator.

Hints for freezing

To help you make the most of the freezing proc-

ess, here are some important hints:

• the maximum quantity of food which can be

frozen in 24 hrs. is shown on the rating plate;

• the freezing process takes 24 hours. No fur-

ther food to be frozen should be added dur-

ing this period;

• only freeze top quality, fresh and thoroughly

cleaned, foodstuffs;

• prepare food in small portions to enable it to

be rapidly and completely frozen and to make

it possible subsequently to thaw only the

quantity required;

• wrap up the food in aluminium foil or poly-

thene and make sure that the packages are

airtight;

• do not allow fresh, unfrozen food to touch

food which is already frozen, thus avoiding a

rise in temperature of the latter;

• lean foods store better and longer than fatty

ones; salt reduces the storage life of food;

• water ices, if consumed immediately after re-

moval from the freezer compartment, can

possibly cause the skin to be freeze burnt;

• it is advisable to show the freezing in date on

each individual pack to enable you to keep

tab of the storage time.

Hints for storage of frozen food

To obtain the best performance from this appli-

ance, you should:

• make sure that the commercially frozen food-

stuffs were adequately stored by the retailer;

• be sure that frozen foodstuffs are transferred

from the foodstore to the freezer in the short-

est possible time;

• not open the door frequently or leave it open

longer than absolutely necessary.

• Once defrosted, food deteriorates rapidly and

cannot be refrozen.

• Do not exceed the storage period indicated

by the food manufacturer.

Care and cleaning

Caution! Unplug the appliance before

carrying out any maintenance operation.

This appliance contains hydrocarbons in its

cooling unit; maintenance and recharging

must therefore only be carried out by authorized

technicians.

Periodic cleaning

The equipment has to be cleaned regularly:

• clean the inside and accessories with luke-

warm water and some neutral soap.

• regularly check the door seals and wipe clean

to ensure they are clean and free from debris.

• rinse and dry thoroughly.

Important! Do not pull, move or damage any

pipes and/or cables inside the cabinet.

Never use detergents, abrasive powders, highly

perfumed cleaning products or wax polishes to

clean the interior as this will damage the surface

and leave a strong odour.

Clean the condenser (black grill) and the com-

pressor at the back of the appliance with a

www.zanussi.com

brush. This operation will improve the perform-

ance of the appliance and save electricity con-

sumption.

Important! Take care of not to damage the

cooling system.

Many proprietary kitchen surface cleaners con-

tain chemicals that can attack/damage the plas-

tics used in this appliance. For this reason it is

recommended that the outer casing of this ap-

pliance is only cleaned with warm water with a

little washing-up liquid added.

After cleaning, reconnect the equipment to the

mains supply.

Defrosting the refrigerator

Frost is automatically eliminated from the evapo-

rator of the refrigerator compartment every time

the motor compressor stops, during normal use.

The defrost water drains out through a drain

hole into a special container at the back of the

appliance, over the motor compressor, where it

evaporates.

It is important to peri-

odically clean the de-

frost water drain hole

in the middle of the

refrigerator compart-

ment channel to pre-

vent the water over-

flowing and dripping

onto the food inside.

Defrosting of the freezer

The freezer compartment of this model, on the

other hand, is a "no frost" type. This means that

there is no buildup of frost when it is in opera-

tion, neither on the internal walls nor on the

foods.

The absence of frost is due to the continuous

circulation of cold air inside the compartment,

driven by an automatically controlled fan.

Periods of non-operation

When the appliance is not in use for long peri-

ods, take the following precautions:

• disconnect the appliance from electrici-

ty supply

• remove all food

• defrost (if foreseen) and clean the appliance

and all accessories

• leave the door/doors ajar to prevent unpleas-

ant smells.

If the cabinet will be kept on, ask somebody to

check it once in a while to prevent the food in-

side from spoiling in case of a power failure.

What to do if…

Warning! Before troubleshooting,

disconnect the mains plug from the mains

socket.

Only a qualified electrician or competent person

must do the troubleshooting that is not in this

manual.

Important! There are some sounds during

normal use (compressor, refrigerant circulation).

Problem Possible cause Solution

The appliance does not op-

erate. The lamp does not

operate.

The appliance is switched off. Switch on the appliance.

www.zanussi.com

Problem Possible cause Solution

The mains plug is not connected to

the mains socket correctly.

Connect the mains plug to the mains

socket correctly.

The appliance has no power. There

is no voltage in the mains socket.

Connect a different electrical appli-

ance to the mains socket.

Contact a qualified electrician.

The Alarm light flashes. The temperature in the freezer is too

high.

Refer to "Excessive Temperature

Alarm"

The lamp does not work. The lamp is in stand-by. Close and open the door.

The lamp is defective. Refer to "Replacing the lamp".

The compressor operates

continually.

The temperature is not set correctly. Set a higher temperature.

The door is not closed correctly. Refer to "Closing the door".

The door has been opened too fre-

quently.

Do not keep the door open longer

than necessary.

The product temperature is too

high.

Let the product temperature de-

crease to room temperature before

storage.

The room temperature is too high. Decrease the room temperature.

Water flows on the rear

plate of the refrigerator.

During the automatic defrosting

process, frost defrosts on the rear

plate.

This is correct.

Water flows into the refrig-

erator.

The water outlet is clogged. Clean the water outlet.

Products prevent that water flows

into the water collector.

Make sure that products do not touch

the rear plate.

Water flows on the ground. The melting water outlet does not

flow in the evaporative tray above

the compressor.

Attach the melting water outlet to the

evaporative tray.

The temperature in the ap-

pliance is too low.

The temperature regulator is not set

correctly.

Set a higher temperature.

The temperature in the ap-

pliance is too high.

Many products are stored at the

same time.

Store less products at the same time.

The temperature in the re-

frigerator is too high.

There is no cold air circulation in the

appliance.

Make sure that there is cold air circu-

lation in the appliance.

The temperature in the

freezer is too high.

Products are too near to each other. Store products so that there is cold

air circulation.

Replacing the lamp

1. Disconnect the mains plug from the mains

socket.

www.zanussi.com

2. Remove the

lamp cover

(refer to the il-

lustration).

3. Replace the

used lamp

with a new

lamp of the

same power

and specifically designed for household ap-

pliances. (the maximum power is shown on

the lamp cover).

4. Connect the mains plug to the mains sock-

et.

5. Open the door. Make sure that the lamp

comes on.

Closing the door

1. Clean the door gaskets.

2. If necessary, adjust the door. Refer to "In-

stallation".

3. If necessary, replace the defective door

gaskets. Contact the Service Center.

Technical data

Dimension of the recess

Height 1900 mm

Width 860 mm

Depth 550 mm

Rising Time 14 h

Voltage 230-240 V

Frequency 50 Hz

The technical information are situated in the rat-

ing plate on the internal left side of the appli-

ance and in the energy label.

Installation

Positioning

Install this appliance at a location where the am-

bient temperature corresponds to the climate

class indicated on the rating plate of the appli-

ance:

Climate

class

Ambient temperature

SN +10°C to + 32°C

N +16°C to + 32°C

ST +16°C to + 38°C

T +16°C to + 43°C

Electrical connection

Before plugging in, ensure that the voltage and

frequency shown on the rating plate correspond

to your domestic power supply.

The appliance must be earthed. The power sup-

ply cable plug is provided with a contact for this

purpose. If the domestic power supply socket is

not earthed, connect the appliance to a sepa-

rate earth in compliance with current regula-

tions, consulting a qualified electrician.

The manufacturer declines all responsibility if

the above safety precautions are not observed.

This appliance complies with the E.E.C. Direc-

tives.

www.zanussi.com

Height adjustment

820

870

The height of the ap-

pliance is adjustable

from 820 to 870 mm

to fine up with exist-

ing kitchen units.

820

870

Before installing the

appliance between

units, adjust the

height of the feet and

rear wheels.

The wheels are facto-

ry set for a height of

820 mm.

To align the appliance

to a height of 870

mm, raise it by adjust-

ing the feet with a

spanner, then remove

the wheels and refit

them in the lowest

position.

Fitting the side panels

17,5

1015

539

260*

541

280

820

• Fit the brackets on-

to the panels in the

positions shown in

the diagram. The

dimension of 260*

mm is allowed for

fitting a 100 mm

plinth below the

panel. For different

plinth sizes, in-

crease the dimen-

sion of 260* mm

accordingly.

1. Rear edge

2. Front edge

3. Right hand side

panel

• Apply spacers to

the hinges before

installing the appli-

ance into the cabi-

net . See picture.

www.zanussi.com

• Rest the panels

against the appli-

ance.

• Fit the rear brack-

ets, taking into ac-

count the thickness

of the panels (maxi-

mum width of unit

900 mm).

• For a correct align-

ment make sure

that the distance

between the appli-

ance and the cabi-

net is of 45 mm.

• Secure the panels

at the front.

• Fix the squares

(contained in the

bag) to the lower

part of the door

(references already

provided).

• If necessary, door

opening agle max

90° can be ob-

tained by introduc-

ing the pivots sup-

plied separately.

See picture.

Fitting the door panels

• Open a door a re-

move the bracket

cover.

Undo the nuts with

washers and re-

move the bracket

from the door.

101325

1013

444MIN.

447MAX.

444MIN.

447MAX.

193193193193

3MIN

214

• Drill the small

doors as shown in

the figure.

1. Top right-hand

front panel

2. Top left-hand

front panel

3. Bottom right-

hand front panel

4. Bottom left-hand

front panel

• Fix the bracket to

the door with the

screws contained

in the bag.

• Refit the bracket on

the adjustment

screws and screw

the nuts with wash-

ers without tighten-

ing them down.

www.zanussi.com

• Close the door and

check that the

small door is posi-

tioned at the re-

quired height, op-

erating the adjust-

ment screws if nec-

essary.

• Use the same

screws for vertical

alignment of the

small doors.

• If necessary, carry

our horizontal align-

ment by shifting the

small doors.

• After aligning the

doors, tighten the

nuts of the brack-

ets and the screws

of the small brack-

et.

• Fix the bracket lo-

cated under the

door to the panel

with the two plastic

washers contained

in the box of acces-

sories.

• Then refit the

bracket cover.

Building the appliance in

• Fit the appliance

into the recess.

• Rotate the bracket

of 180° in order to

obtain the right po-

sition (2). The posi-

tion (1) is on the

delivery.

• Fix it to the wall

with the appropri-

ate bracket.

• The top of the ap-

pliance must be

kept clear to allow

better air circula-

tion.

If a wall unit is fitted

above the appli-

ance, there must

be a gap of 50 mm

between this unit

and the wall and it

must be at least 50

mm below the ceil-

ing.

Fitting the plinth

Alignment height of 820 mm

www.zanussi.com

820

870

170

220

140

190

100

900

• If using a 140 to

170 mm plinth,

make a cut-out as

shown.

140

190

• If using a plinth

higher than 100

mm but less than

140 mm, cut the

height compensa-

tion strip supplied

with the appliance

to the required

depth and fit it be-

tween the plinth

and the ventilation

grille, pressing it in-

to position below

this grille.

• If using a 100 mm

plinth, fit the com-

plete height com-

pensation strip.

Alignment height of 870 mm

100

150

100

• If using a 190 to

220 mm plinth,

make a shown.

• If using a plinth

higher than 150

mm but less than

190 mm, cut the

height compensa-

tion strip supplied

with the appliance

to the required

depth and fit it be-

tween the plinth

and the ventilation

grille.

• If using a 150 mm

plinth, fit the com-

plete height com-

pensation strip.

• If the appliance is

installed at the end

of a row of units,

insert foot E to hold

the plinth in place.

Environmental concerns

The symbol on the product or on its

packaging indicates that this product may not

be treated as household waste. Instead it

should be taken to the appropriate collection

point for the recycling of electrical and

electronic equipment. By ensuring this product

is disposed of correctly, you will help prevent

potential negative consequences for the

environment and human health, which could

otherwise be caused by inappropriate waste

handling of this product. For more detailed

information about recycling of this product,

please contact your local council, your

household waste disposal service or the shop

where you purchased the product.

www.zanussi.com

Sisukord

Ohutusjuhised _ _ _ _ _ _ _ _ _ _ _ _ _ _ 16

Juhtpaneel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 18

Esimene kasutamine _ _ _ _ _ _ _ _ _ _ _ 20

Igapäevane kasutamine _ _ _ _ _ _ _ _ _ 20

Vihjeid ja näpunäiteid _ _ _ _ _ _ _ _ _ _ _ 21

Puhastus ja hooldus _ _ _ _ _ _ _ _ _ _ _ 22

Mida teha, kui... _ _ _ _ _ _ _ _ _ _ _ _ _ _ 23

Tehnilised andmed _ _ _ _ _ _ _ _ _ _ _ _ 25

Paigaldamine _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 25

Keskkonnainfo _ _ _ _ _ _ _ _ _ _ _ _ _ _ 29

Jäetakse õigus teha muutusi.

Ohutusjuhised

Teie turvalisuse huvides ning tagamaks õiget

kasutamist lugege kasutusjuhend, sh näpu-

näited ja hoiatused, hoolikalt läbi, enne kui

paigaldate masina ja kasutate seda esimest

korda. Et vältida asjatuid vigu ja õnnetusi, on

tähtis tagada, et kõik seadet kasutavad inime-

sed tunneksid põhjalikult selle käitamist ja

ohutusseadiseid. Hoidke need juhised alles ja

veenduge, et need oleksid alati seadmega

kaasas, kui selle asukohta muudetakse või

seadme müümise korral, nii et kõik kasutajad

oleksid kogu seadme kasutusaja jooksul selle

kasutamisest ja ohutusest põhjalikult infor-

meeritud.

Elu ja materiaalse vara turvalisuse huvides tu-

leb kinni pidada selles kasutusjuhendis too-

dud ettevaatusabinõudest, sest mittejärgimi-

sest tingitud kahjustuste eest tootja ei vastuta.

Laste ja riskirühma kuuluvate inimeste

turvalisus

• See seade ei ole ette nähtud kasutamiseks

isikute (sh laste) poolt, kelle füüsilised, sen-

soorsed või vaimsed võimed või kogemuse

ja teadmiste puudus seda ei võimalda, v.a.

juhul, kui nende üle teostab järelvalvet või

neid juhendab seadme kasutamisel isik,

kes nende turvalisuse eest vastutab.

Laste puhul tuleb jälgida, et nad seadmega

mängima ei hakkaks.

• Hoidke kogu pakend lastele kättesaamatus

kohas. Lämbumisoht.

• Seadme utiliseerimisel tõmmake pistik pe-

sast välja, lõigake toitekaabel läbi (võimali-

kult seadme lähedalt) ja võtke ära uks, et

mängivad lapsed ei saaks elektrilööki ega

sulgeks end kappi.

• Juhul kui käesolev magnetiseeritud ukseti-

henditega versioon vahetab välja vanema

vedrulukustussüsteemiga seadme, siis en-

ne vana seadme äraviskamist veenduge, et

lukustusmehhanismi poleks võimalik enam

kasutada. Vastasel juhul võib seade muutu-

da lapse jaoks surmalõksuks.

Üldine ohutus

Hoiatus

Hoidke ventilatsiooniavad vabad nii eraldiseis-

va kui ka sisseehitatud seadme puhul.

• Seade on mõeldud toiduainete ja/või jooki-

de selles juhises kirjeldatud viisil koduseks

säilitamiseks.

– personalile mõeldud köökides kauplus-

tes, kontorites ja mujal;

– puhkemajades, hotellides, motellides ja

muudes majutuskohtades;

– hommikusöögiga ööbimiskohtades;

– toitlustust ja sarnast teenust pakkuvates

ettevõtetes.

• Ärge kasutage sulatamise kiirendamiseks

mehaanilisi seadmeid või muid kunstlikke

vahendeid.

• Ärge kasutage külmikus muid elektrisead-

meid (näiteks jäätisevalmistajaid), kui tootja

ei ole vastavat sobivust otseselt kinnitanud.

• Vältige jahutusaine süsteemi kahjustamist.

• Külmiku jahutussüsteemis olev jahutusaine

isobutaan (R600a) on üsna keskkonnaohu-

tu, kuid siiski tuleohtlik looduslik gaas.

Seadme transpordi ja paigaldamise ajal tu-

leb vältida jahutusaine süsteemi kompo-

nentide kahjustamist.

www.zanussi.com

Kui jahutusaine süsteem peaks viga saa-

ma:

– vältige tuleallikate lähedust,

– õhutage põhjalikult ruumi, milles seade

paikneb.

• Seadme parameetrite muutmine või selle

mis tahes viisil modifitseerimine on ohtlik.

Toitejuhtme kahjustamine võib põhjustada

lühiühenduse, tulekahju ja/või elektrilöögi.

Hoiatus Elektriliste komponentide (toite-

juhe, pistik, kompressor) asendustööd tu-

leb ohu vältimiseks tellida kvalifitseeritud teh-

nikult või teenusepakkujalt.

1. Toitejuhtme pikendamine on keelatud.

2. Veenduge, et toitepistik ei ole seadme

tagakülje poolt muljutud ega kahjusta-

tud. Muljutud või kahjustatud toitepistik

võib üle kuumeneda ja põhjustada tule-

kahju.

3. Tagage juurdepääs seadme toitepisti-

kule.

4. Ärge eemaldage pistikut juhtmest tõm-

bamise teel.

5. Kui toitepesa logiseb, siis ärge toitepis-

tikut sisestage. Elektrilöögi- või tuleoht!

6. Seadet ei tohi kasutada ilma siseval-

gusti katteta (kui see on ette nähtud).

• See seade on raske. Seda liigutades olge

ettevaatlik.

• Ärge eemaldage ega puudutage sügavkül-

mas olevaid esemeid, kui teie käed on niis-

ked/märjad, kuna see võib põhjustada na-

hamarrastusi või külmahaavandeid.

• Vältige seadme pikemaajalist kokkupuudet

otsese päikesevalgusega.

• Selles seadmes kasutatavad lambid (kui

need on ette nähtud) on mõeldud kasutami-

seks üksnes kodumasinates. Need ei sobi

ruumide valgustamiseks.

Igapäevane kasutamine

• Ärge asetage tuliseid nõusid seadme plast-

massist osadele.

• Ärge hoidke seadmes kergestisüttivat gaasi

või vedelikku, sest need võivad plahvatada.

• Ärge paigutage toiduaineid vastu tagasei-

nas asuvat õhu väljalaskeava. (Kui on tege-

mist härmatisevaba seadmega)

• Külmutatud toituaineid ei tohi pärast sulata-

mist uuesti külmutada.

• Säilitage eelpakendatud sügavkülmutatud

toitu vastavalt toidu tootja juhistele.

• Rangelt tuleb järgida seadme tootja pool-

seid hoiustamisnõuandeid. Vaadake vasta-

vaid juhiseid.

• Ärge paigaldage külmikusse gaseeritud joo-

ke, kuna see tekitab anumas rõhju, mis

võib põhjustada plahvatuse, mis omakorda

kahjustab seadet.

• Seadmega tehtud jää võib otse seadmest

söömisel külmapõletust tekitada.

Hooldus ja puhastamine

• Enne hooldust lülitage seade välja ja ee-

maldage toitepistik seinakontaktist.

• Ärge puhastage masinat metallist esemete-

ga.

• Ärge kasutage seadmest härmatise eemal-

damiseks teravaid esemeid. Kasutage

plastmassist kaabitsat.

• Kontrollige regulaarselt külmutuskapi sula-

misvee äravoolu. Vajadusel puhastage ära-

vooluava. Kui see on ummistunud, koguneb

vesi seadme põhja.

Paigaldamine

Tähtis Elektriühenduse puhul jälgige hoolikalt

vastavas alalõigus toodud juhiseid.

• Pakkige seade lahti ja kontrollige kahjustus-

te osas. Ärge ühendage seadet, kui see on

viga saanud. Teatage võimalikest kahjus-

tustest koheselt toote müüjale. Sel juhul jät-

ke pakend alles.

• On soovitatav enne seadme taasühenda-

mist oodata vähemalt kolm tundi, et õli

saaks kompressorisse tagasi voolata.

• Seadme ümber peab olema küllaldane õhu-

ringlus, selle puudumine toob kaasa üle-

kuumenemise. Et tagada küllaldane venti-

latsioon, järgige paigaldamisjuhiseid.

• Kus võimalik, peaks seadme tagakülg ole-

ma vastu seina, et vältida soojade osade

www.zanussi.com

(kompressor, kondensaator) puudutamist ja

võimalikke põletusi.

• Seade ei tohi asuda radiaatorite või pliitide

lähedal.

• Pärast seadme paigaldamist veenduge, et

toitepistikule oleks olemas juurdepääs.

• Ühendage ainult joogiveevarustusega (kui

veeühendus on ette nähtud).

Teenindus

• Kõik masina hoolduseks vajalikud elektri-

tööd peab teostama kvalifitseeritud elektrik

või kompetentne isik.

• Käesolev toode tuleb teenindusse viia voli-

tatud teeninduskeskussesse ja kasutada to-

hib ainult originaal varuosi.

Keskkonnakaitse

Käesolev seade ei sisalda osoonikihti

kahjustada võivaid gaase ei selle külmu-

tussüsteemis ega isolatsioonimaterjalides.

Seadet ei tohi likvideerida koos muu olmeprü-

giga. Isolatsioonivaht sisaldab kergestisütti-

vaid gaase: seade tuleb utiliseerida vastavalt

kohaldatavatele määrustele, mille saate oma

kohalikust omavalitsusest. Vältige jahutus-

seadme kahjustamist, eriti taga soojusvaheti

läheduses. Selles seadmes kasutatud mater-

jalid, millel on sümbol

, on korduvkasutata-

vad.

Juhtpaneel

Sügavkülmiku juhtpaneel

1 2 3 5 6 7 8 94

1. Märgutuli

2. SISSE/VÄLJA-lüliti

3. Temperatuuriregulaator (kõige soojem)

4. Temperatuuri indikaator

5. Temperatuuriregulaator (kõige külmem)

6. Hoiatustuli

7. Hoiatussignaali lähtestuslüliti

8. Funktsiooni Action Freeze tuli

9. Funktsiooni Action Freeze lüliti

Tähtis

Kui uksed on kinni, on sügavkülmiku juhtpa-

neel SISSE lülitatud.

Sisselülitamine

Sisestage toitepistik pistikupessa.

Vajutage SISSE/VÄLJA-lülitit.

Märgutuli süttib põlema.

Väljalülitamine

Sügavkülmiku väljalülitamiseks vajutage SIS-

SE/VÄLJA-lülitit, kuni märgutuli ja tempera-

tuuri indikaator kustuvad.

Temperatuuri reguleerimine

Temperatuuri saab reguleerida vahemikus

-15°C kuni -24°C.

Temperaturiregulaatorite vajutamisel hakkab

temperatuuri indikaatoril vilkuma olemasoleva

temperatuuri näit. Temperatuuri on võimalik

reguleerida ainult indikaatori vilkumise ajal.

Temperatuuri tõstmiseks vajutage tempera-

tuuriregulaatori plussnuppu. Temperatuuri

alandamiseks vajutage temperatuuriregulaa-

tori miinusnuppu. Temperatuuri indikaator ku-

vab mõneks sekundiks uue määratud tempe-

ratuuri ning näitab seejärel taas sügavkülmiku

sisetemperatuuri.

Uue määratud temperatuurini jõudmiseks ku-

lub 24 tundi.

www.zanussi.com

Ettevaatust Temperatuuri

stabiliseerumisaja jooksul pärast

sügavkülmiku esmast käivitamist ei vasta

kuvatav temperatuur valitud temperatuurile.

Temperatuuri indikaator

Tavarežiimis töötamisel näitab seade sügav-

külmiku sisetemperatuuri.

Tähtis Erinevuse olemasolu kuvatava

temperatuuri ja tegeliku temperatuuri vahel on

normaalne. Eriti siis, kui:

• hiljuti on valitud uus seade,

• uks on pikka aega lahti olnud,

• seadmesse on pandud sooja toitu.

Liiga kõrge temperatuuri signaal

Kui temperatuur sügavkülmikus liialt kõrgele

tõuseb (nt pärast voolukatkestust), hakkab

märgutuli vilkuma ja sisse lülitub helisignaal.

Normaalse temperatuuri taastumisel helisig-

naal vaikib, kuid märgutule vilkumine jätkub.

Pärast märgutule lähtestusnupu vajutamist

hakkab näidikul vilkuma kõige kõrgema vahe-

peal mõõdetud temperatuuri näit.

Pärast pikemat voolukatkestust tuleb külmuta-

tud toit võimalikult kiiresti ära tarvitada või siis

läbi küpsetada ja uuesti külmutada.

Funktsioon Action Freeze

Funktsiooni Action Freeze sisselülitamiseks

vajutage nuppu Action Freeze.

Funktsiooni Action Freeze tuli süttib.

Funktsiooni sisselülitamisel kuvatakse näidi-

kule SP .

Tähtis Funktsioon lülitub ligikaudu 52 tunni

pärast automaatselt välja.

Funktsiooni saab igal ajal välja lülitada, vaju-

tades nuppu Action Freeze. Funktsiooni Ac-

tion Freeze tuli kustub.

Külmiku juhtpaneel

1 2 3 5 6 74

1. Märgutuli

2. SISSE/VÄLJA-lüliti

3. Temperatuuriregulaator (kõige soojem)

4. Temperatuuri indikaator

5. Temperatuuriregulaator (kõige külmem)

6. Action Cool-tuli

7. Action Cool-lüliti

Sisselülitamine

Sisestage toitepistik pistikupessa.

Vajutage SISSE/VÄLJA-lülitit.

Märgutuli süttib põlema.

Väljalülitamine

Külmiku väljalülitamiseks vajutage SISSE/

VÄLJA-nuppu, kuni märgutuli ja temperatuuri

indikaator kustuvad.

Temperatuuri reguleerimine

Temperatuuri saab reguleerida vahemikus

+2°C kuni +8°C.

Temperaturiregulaatorite vajutamisel hakkab

temperatuuri indikaatoril vilkuma olemasoleva

temperatuuri näit. Temperatuuri on võimalik

reguleerida ainult indikaatori vilkumise ajal.

Temperatuuri tõstmiseks vajutage tempera-

tuuriregulaatori plussnuppu. Temperatuuri

alandamiseks vajutage temperatuuriregulaa-

tori miinusnuppu. Temperatuuri indikaator ku-

vab mõneks sekundiks uue määratud tempe-

ratuuri ning näitab seejärel taas külmiku sise-

temperatuuri.

Uue määratud temperatuurini jõudmiseks ku-

lub 24 tundi.

www.zanussi.com

Ettevaatust Temperatuuri

stabiliseerumisaja jooksul pärast külmiku

esmast käivitamist ei vasta kuvatav

temperatuur valitud temperatuurile. Sel ajal

võib näidatav temperatuur olla madalam, kui

määratud temperatuur.

Temperatuuri indikaator

Tavarežiimis töötamisel näitab seade külmiku

sisetemperatuuri.

Tähtis Erinevuse olemasolu kuvatava

temperatuuri ja tegeliku temperatuuri vahel on

normaalne. Eriti siis, kui:

• hiljuti on valitud uus seade,

• uks on pikka aega lahti olnud,

• seadmesse on pandud sooja toitu.

Funktsioon Action Cool

Maksimaalne jõudlus saavutatakse funktsioo-

ni Action Cool abil. See funktsioon on mõel-

dud juhuks, kui külmikusse pannakse korraga

palju toitu.

Funktsiooni Action Cool sisselülitamiseks va-

jutage nuppu Action Cool.

Funktsiooni Action Cool tuli süttib.

Tähtis Sisetemperatuur langeb +2°C-ni.

Umbes 6 tunni möödudes lülitub funktsioon

Action Cool automaatselt välja.

Esimene kasutamine

Sisemuse puhastamine

Enne seadme esmakordset kasutamist, peske

seadme sisemus ja kõik lisatarvikud leige vee

ja neutraalse seebiga eemaldamaks uutele

toodetele omast lõhna ja kuivatage seade

hoolikalt.

Tähtis Ärge kasutage pesuvahendeid ja abra-

siivseid pulbreid, kuna need kahjustavad sise-

pindu.

Igapäevane kasutamine

Värske toidu külmutamine

Sügavkülmiku-osa sobib värske toidu külmu-

tamiseks ning külmutatud ja sügavkülmutatud

toidu pikaajaliseks säilitamiseks.

Pange värske külmutatav toit vasakule poole

ja kui toit on külmunud, tõstke see ümber säi-

lituskorvidesse.

24 tunni jooksul külmutatava toidu maksimaal-

ne kogus on määratletud andmesildil, mis

asub seadme siseküljel.

Külmutusprotsess kestab 24 tundi: selle aja

jooksul ärge muid toiduaineid külmutamiseks

lisage.

www.zanussi.com

Page is loading ...

Zanussi ZBB47460DA User manual

Brand: Zanussi

Model: ZBB47460DA

Category: Fridges

Type: User manual

Download PDF

report

in other languages

русский: Zanussi ZBB47460DA Руководство пользователя
eesti: Zanussi ZBB47460DA Kasutusjuhend

Zanussi ZBB47460DA User manual

Zanussi ZBB47460DA User manual

in other languages

Related papers

Other documents