Walker H17 50" Snowblower User manual

Brand: Walker

Model: H17 50" Snowblower

Category: Snow throwers

Type: User manual

This manual is also suitable for

H12 42" Snowblower

Safety, Assembly, Operating and Maintanence Instructions

H12 compatible with tractor models: MC, MD, MT

H17 compatible with tractor models: MH

Please Read and Save These Instructions

For Safety, Read All Assembly and Opeartion Instructions

Prior to Operating Attachment

H12 Beginning S/N: 21810237

H17 Beginning S/N: 21810546

P/N: 6670-16

H12: 42” Two-Stage Snowblower

H17: 50” Two-Stage Snowblower

Operator’s Manual

Foreword

Thank you. . .for purchasing a Walker Two-Stage Snowblower. Every effort has been made to

provide you with the most reliable machine on the market, and we are sure you will be among our

many satised customers. If for any reason this product does not perform to your expectations,

please contact your local dealer. Every customer is important to us. Your satisfaction is our goal.

Please. . .read this manual thoroughly! Before you operate your machine, please read this entire

manual. Some of the information is crucial for proper operation - it will help protect your investment

and ensure that the machine performs to your satisfaction. Some of the information is important

to your safety, and must be read and understood to help prevent possible injury to the operator

or others. If anything in this manual is confusing or hard to understand, please contact your local

authorized dealer or call our service department, at (970) 221-5614, for clarication before operating

or servicing this machine.

This manual covers the H12, 42 in. Two-Stage Snowblower and the H17, 50 in. Two-Stage

Snowblower.

All shields and guards must be in place for the proper and safe operation of this machine.

Where they are shown removed in this manual, it is for illustration purposes only. Do not operate

this machine unless all shields and guards are in place.

Specications given are based on the latest information available at the time this manual was

produced.

Walker Mfg. Co. is continually striving to improve the design and performance of its products.

We reserve the right to make changes in specications and design without thereby incurring any

obligation relative to previously manufactured products.

Sincerely,

WALKER MANUFACTURING COMPANY

Bob Walker, President

Table of Contents

General Information __________________1

HIGHLIGHTED INFORMATION _______________1

GLOSSARY ______________________________1

IDENTIFYING NUMBER LOCATION ___________1

UNIT DESCRIPTION ________________________1

Specications __________________________2

Component Identication _____________3

Safety Instructions ____________________5

BEFORE OPERATING ______________________5

OPERATING ______________________________6

MAINTENANCE ___________________________8

SAFETY, CONTROL, AND

INSTRUCTION DECALS ____________________9

Assembly Instructions ________________ 11

Installation Instructions ______________13

H10: LOCKING/REMOVING IMPLEMENTS ____13

H19: LOCKING/REMOVING IMPLEMENTS ____14

H19: FLOAT FUNCTION ADJUSTMENT _______15

Operating Instructions _______________17

PREOPERATION CHECKLIST ______________17

SNOWBLOWER CONTROLS _______________18

Chute Rotation Handle ��18

Deector Position Knobs __________________18

Raising/Lowering _______________________18

SNOWBLOWER OPERATION _______________19

Engaging the Snowblower ________________19

RECOMMENDATIONS FOR SNOWBLOWING __19

REMOVING SNOW ________________________20

CLOGGING CHECKLIST ___________________20

REMOVAL AND STORAGE _________________21

H10 and H19 Instructions _________________21

Storing the Snowblower ��21

Maintenance Instructions ____________22

LUBRICATION ___________________________23

Snowblower Gearbox ��23

Snowblower Reduction Chain ��23

Grease Fitting and Oil Point Lubrication ��23

LUBRICATION POINTS DIAGRAM ___________24

REPLACING AND REPAIRING PARTS ________25

Snowblower Cutting Edge ��25

Snowblower Reduction Chain ��25

Snowblower Reduction Sprockets ��26

Replacing Drive Shaft with

Sprocket (P/N I153)��26

Replacing Large Sprocket (P/N I161) ��26

ADJUSTMENTS __________________________27

Snowblower Skid Shoes ��27

Snowblower Reduction Chain Tension ��27

H19 Hitch Lock Tension Adjustment _________28

Parts Diagrams ______________________ 29

H12 SNOWBLOWER DRIVE COMPONENTS ___29

H12 SNOWBLOWER HOUSING

COMPONENTS ___________________________31

H17 SNOWBLOWER DRIVE COMPONENTS ___33

H17 SNOWBLOWER HOUSING

COMPONENTS ___________________________35

MAINTENANCE AND SERVICE

RECORD SHEET _________________________37

Warranty _____________________________40

General Information

HIGHLIGHTED INFORMATION

Walker Manufacturing recommends that any service

requiring special training or tools be performed by

an authorized Walker Mower Dealer. There are sev-

eral general practices to be aware of in the area of

safety. Most accidents associated with the opera-

tion or maintenance of a Walker product are caused

by disregarding basic safety precautions or specic

warnings. Such accidents, in most cases, can be

prevented by being aware of the dangers present.

Information of special importance has been high-

lighted in bold type in this manual. Refer to Safety

Instructions for the meanings of DANGER, WARN-

ING, CAUTION, IMPORTANT, and NOTE.

GLOSSARY

There are many terms that are either unique to

this equipment or that are used as acronyms. The

following terms and their denitions will help while

using this manual.

● FORWARD SPEED CONTROL (FSC) controls

the maximum forward speed of the tractor;

functioning as a cruise control.

● IMPLEMENT refers to the two-stage snow-

blower used with the tractor with an implement hitch

installed.

● LEFT HAND (LH) refers to the left-hand side

of the machine when the operator is seated facing

forward in the tractor seat.

● MACHINE consists of the implement installed

on the tractor, functioning as a single unit.

● POWER TAKE-OFF (PTO) transmits engine

power to run the two-stage snowblower.

● RIGHT HAND (RH) refers to the right-hand side

of the machine when the operator is seated facing

forward in the tractor seat.

● TRACTOR is the prime mover, including the

engine, drivetrain, operator seat, and controls to

operate the machine.

IDENTIFYING NUMBER LOCATION

The two-stage snowblower serial number is afxed

to the RH side of the snowblower head frame. Model

and serial numbers are helpful when obtaining

replacement parts and maintenance assistance.

For ready reference, please record these numbers

in the space provided.

Two-Stage Snowblower Model No.

Two-Stage Snowblower Serial No.

Date of Purchase

Fill In By Purchaser

Serial Number

Two-Stage Snowblower Serial Number Location

(Rear View and RH View)

UNIT DESCRIPTION

The 42 in. (107 cm) two-stage snowblower throws

snow up to 40 ft (12 m). It is raised and lowered

automatically with the lift control switch. The blower

spout is controlled with a simple position control

handle, or the Snowblower Chute Control Kit (P/N

6623-4) for use with model H only. The snowblower

is powered by the tractor PTO through the PTO

shaft, snowblower drive shaft, and gearbox. Tire

chains and a soft cab are available as optional

equipment for Models C, T, and D. Tire chains and

a hard cab are available as optional equipment for

Model H.

Specications

Height Without Chute in. (cm) 20-1/2 (52) 20 (51)

Width in. (cm) 42-1/4 (107) 50 (127)

Length With Female Hitch in. (cm) 30 (76) 30 (76)

Overall Length Installed on Tractor in. (cm)* 97-1/2 (248) 105 (267)

Cutting Height in. (cm) 19 (48) 19 (48)

Weight With Female Hitch lb (kg) 180 (82) 193 (88)

Throwing Distance ft (m) 40 (12) 40 (12)

Lift 12 Volt DC Electric Linear Actuator, Operated by Toggle

Switch Mounted on FSC Lever

Hitch System Patented Quick Hitch System

Type Blower Two-Stage with 12-7/8 in. (33 cm) Diameter Auger and

15-3/4 in. (40 cm) Diameter, 3-Blade Impeller, Clockwise

Rotation

Snowblower PTO Drive Quick Disconnect Splined PTO Shaft with Two (2) High-

Speed U-Joints

Impeller Drive Chain, #40

Driving Sprocket: H40C11

Driven Sprocket: H40B32

Auger Drive Worm Gearbox, 5:1 Ratio, SAE EP 90W Gear Oil

Discharge Angle Adjustment Chute Direction Rotates 228

by Crank Handle, Adjustable

Spout Deector, Adjustable from Operator Seat, Up to 40

ft. (12 m) Discharge Distance

Optional P/N 6623-4 Snowblower Chute Control Kit, avail-

able for Model MH with A33 Hard Cab Installed

Body Construction Frame Thickness: 14 Gauge Steel

Side Thickness: 11 Gauge Steel

Impeller Housing Thickness: 14 Gauge Steel

Depth Guide Two Adjustable, Replaceable Skid Shoes, Adjustable from

1/4 to 3/4 in. (6 to 19 cm)

TWO-STAGE SNOWBLOWER H12 H17

NOTE: The manufacturer reserves the right to make changes in specications shown herein at any time

without notice or obligation.

* H12 with model MT, H17 with model MH

H12

● The following are required for mounting the H12 42 in. Two-Stage Snowblower

- C, T, D Tractors: H10 Implement Mount Hitch

- H Tractors: H19 Implement Mount Hitch

H17

● The following are required for mounting the H17 50 in. Two-Stage Snowblower

- T, D Tractors: H10 Implement Mount Hitch

- H Tractors: H19 Implement Mount Hitch

Component Identication

Two-Stage Snowblower Front View and Right Side View (Not Installed)

Deector

Deector Position

Control Knob

Chute

Hand Guard

Chute Rotation

Handle

Fan

Frame

Auger

Gearbox

Auger

Gearbox Support

Bracket

Component Identication

Two-Stage Snowblower Rear View (Not Installed)

Deector

Deector Position

Control Knob

Snowblower

Housing

Skid Shoe

Female Quick Hitch

PTO Drive Shaft

Skid Shoe

Reduction

Box Cover

Chute Rotation

Handle

Chute

Safety Instructions

Pay particular attention to any information labeled

DANGER, WARNING, CAUTION, IMPORTANT,

and NOTE in this manual.

When you see the Safety Alert Symbol ( ), read,

understand, and follow the instructions. Fail ure to

comply with safety instructions may result in person-

al injury.

The seriousness or degree of importance of each

type of information is dened as follows:

DANGER

An IMMEDIATE hazard that WILL result in

severe personal injury or DEATH, if warn-

ing is ignored and proper safety precau-

tions are not taken.

WARNING

A POTENTIAL hazard that COULD result in

severe personal injury or DEATH, if warn-

ing is ignored and proper safety precau-

tions are not taken.

CAUTION

Possible hazards or unsafe practices that

MAY result in MODERATE personal injury

or property damage, or machine damage, if

warning is ignored and proper safety pre-

cautions are not taken.

IMPORTANT: Identies mechanical information

demanding special attention, since it deals with the

possibility of damaging a part or parts of the ma-

chine.

NOTE: Identies information worthy of special

attention.

Walker Manufacturing cannot predict every potential-

ly dangerous situation. Therefore, items labeled as

such in this manual do not cover all conceivable situ-

ations. Any person using procedures, tools, or control

techniques not recommended by Walker Manufactur-

ing must take full responsibility for safety.

The Walker Rider Lawnmower has been designed

with many safety features to protect the operator

from personal harm or injury. However, it is neces-

sary for the operator to use safe operating proce-

dures at all times. Failure to follow safety instruc-

tions contained in this manual may result in

personal injury or damage to equipment or prop-

erty.

If you have any questions concerning setup, opera-

tion, maintenance, or safety, please contact your

authorized Walker Mower dealer or call Walker

Manufacturing Company at (970) 221-5614.

BEFORE OPERATING

1. Read and understand the contents of this

Operator’s Manual before starting and oper-

ating the machine. Become thoroughly famil-

iar with all machine controls and how to stop the

machine and disengage the controls quickly.

Replacement Operator’s Manuals are available

by sending the Model and Serial Number to:

Walker Manufacturing Company

5925 East Harmony Road

Fort Collins, CO 80528

2. Never allow children to operate rider mower.

Do not allow adults to operate without proper

instruction.

3. Do not allow anyone other than the operator on

the machine.

4. Keep everyone, especially children and pets, a

safe distance away from the area of operation.

Do not operate with bystanders in the area.

5. Do not operate the machine barefoot or wear-

ing sandals, sneakers, tennis shoes, or similar

lightweight footwear. Wear substantial pro-

tective footwear.

6. Snow or leaves can sometimes hide objects

that might clog the snowblower, or otherwise

cause damage. Clear the area of doormats,

sleds, boards, wires and other debris.

Safety Instructions

7. Do not wear loose tting clothing that could get

caught in moving parts. Do not operate this

machine while wearing shorts; always wear

adequate protective clothing, including long

pants. Wearing safety glasses, safety shoes,

and a helmet is advisable and required by some

local ordinances and insurance regulations.

8. Prolonged exposure to loud noise can cause

impairment or loss of hearing. Operator hear-

ing protection is recommended. Wear a

suitable hearing protective device, such as ear-

muffs or earplugs.

9. Keep all protective shields and safety devic-

es in place. If a protective shield, safety de-

vice, or decal is damaged, unusable, or miss-

ing, repair or replace it before operating the

machine.

10. Be sure interlock switches are functioning

correctly, so the engine cannot be started un-

less the Forward Speed Control lever is in the

NEUTRAL-PARK position, the PTO clutch is

in the DISENGAGED position, and the Park-

ing Brake in the ENGAGED position. Also, the

engine should stop if the operator lifts off the

seat with any one or more of these controls in

the operating position: (1) Forward Speed Con-

trol (FSC) out of NEUTRAL-PARK, (2) PTO

Clutch ENGAGED, or (3) Parking Brake DIS-

ENGAGED

11. Handle gasoline with care. Gasoline is highly

ammable and its vapors are explosive:

a. Use an approved fuel container.

b. Never add fuel to a running engine or hot

engine (allow hot engine to cool several

minutes).

c. Keep matches, cigarettes, cigars, pipes,

open ames, or sparks away from the fuel

tank and fuel container.

d. Always ll the fuel tank outdoors using

care. Fill to about one inch from the top of

the tank. Use a funnel or spout to prevent

spilling.

e. Replace the machine fuel cap and contain-

er cap securely and clean up any spilled

fuel before starting the engine.

11. Never attempt to make any adjustments

while the engine is running, except where

specically instructed to do so.

12. The snow or leaves can sometimes hide objects

that might clog the snowblower or debris blower

chute, or otherwise cause damage. Clear the

area of doormats, sleds, boards, wires and oth-

er debris.

13. The electrical system battery contains sulfuric

acid. Avoid any contact with skin, eyes, and

clothing. Keep the battery and acid out of reach

of children.

WARNING

This product can expose you to chemicals

including Di-(2-ethylhexyl) phthalate which

is known to the State of California to cause

cancer, and Di-(2-ethylhexyl) phthalate,

which is known to the State of California

to cause birth defects or other repro-

ductive harm. For more information go to

www.P65Warnings.ca.gov.

OPERATING

NOTE: Refer to your tractor Operator’s Manual for

safety instructions for operating the tractor.

1. Operate the machine only in daylight or in

good articial light with good visibility of areas

being cleaned.

2. Sit on the seat when starting the engine and op-

erating the machine. Keep feet on footrests at

all times when the tractor is moving and/or the

implement is operating.

3. For a beginning operator, learn to steer (ma-

neuver) the tractor with a slow engine speed

before attempting any implement operation.

Be aware that, with the front mounted imple-

ment conguration, the back of the machine

swings to the outside during turns.

Safety Instructions

DANGER

Do not operate around overhanging tree

branches or bushes at the same height as

the operator’s torso and head where inad-

vertent contact may cause injury.

4. Remember, for an emergency stop, the forward

motion of the tractor can always be stopped by

pulling the Forward Speed Control (FSC) into

the NEUTRAL-PARK position.

5. In case the transmission drive belt breaks

during operation, and if the machine is on a

slope, the machine will freewheel down the

slope. To maintain control, immediately (1)

Release the steering levers and simultaneously

(2) Move the FSC to the NEUTRAL-PARK po-

sition. When the machine is stopped or moving

slowly, engage the parking brake.

NOTE: The emergency stop procedure is ex-

actly the same procedure used to normally stop

and park the machine.

6. Disengage the PTO clutch, put the FSC in the

NEUTRAL-PARK position, and engage the

parking brake before starting the engine (an

ignition interlock switch normally prevents start-

ing of the tractor if these controls are in the OP-

ERATING position).

7. Do not operate machine if the operator pres-

ence safety switch system is not working.

Verify proper operation by having the operator

lift off the seat with the engine running and mov-

ing three controls, one at a time; (1) Move the

FSC lever out of the NEUTRAL-PARK position,

(2) Engage the PTO Clutch, and (3) Disengage

the Parking Brake. Moving any of these con-

trols should stop the engine after a 1/2 second

delay.

8. Do not run the engine in a conned area

without adequate ventilation. Exhaust fumes

are hazardous and can be deadly.

9. Do not carry passengers - maximum seating

capacity is one (1) person.

10. Make sure the auger is clear of snow, ice, or

debris before engaging the PTO clutch.

11. Be careful never to throw snow towards people

or cars, and never allow anyone in front of the

implement.

12. Watch out for hazards hidden under snow that

could enter the chute while operating.

13. Avoid sudden starts or stops. Before back-

ing the machine up, look to the rear to be sure

no one is behind the machine. Watch carefully

for trafc when crossing or working near road-

ways.

14. When moving forward, do not suddenly put the

tractor in reverse by rapidly pulling on the steer-

ing levers, especially when going downhill, as

this can lift the tractor tail wheel off the ground

and set up a bucking motion due to operator

overcontrol. If bucking does occur, immediate-

ly stop the bucking action by pulling the For-

ward Speed Control (FSC) lever into the NEU-

TRAL-PARK position.

15. Disengage the PTO clutch when transporting

the machine.

16. Do not operate across the face of slopes. Use

extreme caution when changing direction on

slopes. Do not attempt to operate on steep

slopes. Do not operate the machine on a

slope greater than 15 degrees.

17. Never adjust gauge wheels or skid shoes

with the engine running. Before adjusting

height or servicing, disengage the PTO clutch,

stop the engine, and remove the ignition key.

Wait for all movement to stop before getting off

the seat.

NOTE: The PTO brake should stop drive line

rotation within ve (5) seconds of disengaging

the PTO clutch. If the brake is not functioning

properly, have it repaired by an authorized deal-

er before further operation.

18. Do not operate the snowblower with the blower

spout assembly removed.

19. If snowblower clogs:

a. Disengage the PTO clutch, stop the engine,

and remove the ignition key before leaving

the seat.

b. LOOK to make sure PTO shaft and auger

movement has stopped before trying to un-

clog the snowblower.

Safety Instructions

c. Disconnect the fuel solenoid wire [diesel

engines] or spark plug wire(s) [gasoline en-

gines].

d. DO NOT use hands or feet to unclog the

snowblower - use a stick or similar tool.

20. If the implement strikes a solid object or the

machine begins to vibrate abnormally, imme-

diately disengage the PTO clutch, stop the

engine, and wait for all moving parts to

stop. Disconnect the fuel solenoid wire [diesel

engines] or the spark plug wire(s) [gasoline en-

gines] to prevent accidental starting. Thorough-

ly inspect the implement and repair any damage

before restarting the engine and operating the

machine. Make sure implement components

are in good condition and all bolts are tight.

21. Do not touch the engine or mufer while

the engine is running or immediately after

stopping the engine. These areas may be hot

enough to cause serious burns.

22. When leaving the machine unattended, disen-

gage the PTO clutch, stop the engine, and

remove the ignition key.

MAINTENANCE

NOTE: Refer to your tractor Operator’s Manual for

safety instructions for tractor maintenance.

1. To prevent accidental starting of the engine

when servicing or adjusting the machine, re-

move the key from the ignition switch and dis-

connect the fuel solenoid wire [diesel engines]

or the spark plug wire(s) [gasoline engines].

2. To reduce re hazards, keep the engine free

of grass, leaves, excessive grease, and dirt.

3. Keep all nuts, bolts, and screws tight to ensure

the machine is in a safe, working condition.

4. Perform only maintenance instructions de-

scribed in this manual. Unauthorized main-

tenance operations or machine modications

may result in unsafe operating conditions.

5. If the engine must be running to perform a

maintenance adjustment, keep hands, feet

and clothing away from moving parts. Do

not wear jewelry or loose clothing.

6. Always use the proper engine service man-

ual when working on the engine. Unautho-

rized maintenance operations or modications

to the engine may result in unsafe operating

conditions.

7. Altering the machine in any manner which ad-

versely affects its operation, performance, du-

rability or use will VOID the warranty and may

cause hazardous conditions.

8. Never attempt to disconnect any safety devices

or defeat the purpose of these safety devices.

9. Do not change the engine governor settings or

overspeed the engine. The governor has been

factory-set for maximum-safe engine operating

speed.

10. Use genuine factory replacement parts.

Substitute parts may result in product malfunc-

tion and possible injury to the operator and/or

others.

IMPORTANT: Keep all applicable manuals im-

mediately accessible to anyone who may oper-

ate or service this machine.

Safety Instructions

SAFETY, CONTROL, AND INSTRUCTION DECALS

Safety, Control, and Instruction Decals are installed on the machine;

if any are missing, illegible, or damaged, a replacement should be ordered and installed before

putting the machine into operation. The Decal Part Number is listed below and in the Parts Manual.

Safety Decal: Rotating Driveline

Location: PTO Shield

Location: Snowblower housing

Location: Discharge Chute

Part Number: 7822

DANGER

ROTATING DRIVELINE

KEEP AWAY!

CONTACT CAN CAUSE DEATH

IMPORTANT

When raising tractor body, the PTO shield must be closed or in the down

position and the implement in the lowered position. Open the PTO shield ONLY for connecting

or disconnecting driveline.

– DO NOT OPERATE WITHOUT –

ALL DRIVELINE, TRACTOR AND EQUIPMENT SHIELDS IN PLACE.

DRIVELINES SECURELY ATTACHED AT BOTH ENDS.

DRIVELINE SHIELDS THAT TURN FREELY ON DRIVELINE.

7822

STOP ENGINE BEFORE LUBRICATING

LUBRICATE CHAIN EVERY

4 HOURS WITH CHAIN

SAW CHAIN LUBRICATE

137

Lubrication Decal: Lubricate Chain

Safety Decal: Keep Hands Out

Part Number: 657804 (RAD)

Part Number: 657761 (RAD)

DANGER

TO AVOID SERIOUS INJURY:

KEEP HANDS OUT OF DISCHARGE

CHUTE WHILE ENGINE IS RUNNING.

SHUT OFF ENGINE BEFORE

UNCLOGGING DISCHARGE CHUTE.

133

Safety Decal: Rotating Driveline

Location: PTO Guard

Location: Above Serial Numer Plate

Part Number: 657763 (RAD)

Part Number: 655683 (RAD)

DANGER

ROTATING DRIVELINE

CONTACT CAN CAUSE DEATH.

KEEP PEOPLE AND CLOTHING AWAY.

DO NOT OPERATE WITHOUT:

ALL DRIVELINE, TRACTOR

AND EQUIPMENT SHIELDS

IN PLACE

DRIVELINE SECURELY

ATTACHED AT BOTH ENDS

DRIVELINE SHIELD TURNING

FREELY ON DRIVELINE.

135

IMPORTANT

BEFORE USING:

• OIL LEVEL MUST BE CHECKED

• FILL WITH SAE 80W90. “AGMA 5 EP”

EXTREME PRESSURE OIL OR EQUIVALENT.

• READ INSTRUCTIONS MANUAL.

Safety Instructions

SAFETY, CONTROL, AND INSTRUCTION DECALS

Safety, Control, and Instruction Decals are installed on the machine;

if any are missing, illegible, or damaged, a replacement should be ordered and installed before

putting the machine into operation. The Decal Part Number is listed below and in the Parts Manual.

WARNING

FAILURE TO FOLLOW SAFE OPERATING

PROCEDURES MAY RESULT IN INJURY.

FOR SAFE OPERATION FOLLOW ALL OPERATING

INSTRUCTIONS AND SAFETY PRECAUTIONS IN

OPERATOR’S MANUAL.

EYE PROTECTION MUST BE WORN AT ALL TIMES.

KEEP HANDS, FEET AND CLOTHING AWAY FROM POWER

DRIVEN PART.

STOP ENGINE BEFORE LEAVING OPERATOR POSITION.

WAIT FOR ALL MOVEMENTS TO STOP BEFORE STARTING

TO ADJUST, LUBRICATE, CLEAN OR UNCLOG THE MACHINE.

KEEP THE AREA OF OPERATION CLEAR OF ALL PERSONS

AND ANIMALS.

KEEP ALL GUARDS AND SHIELDS IN PLACE.

NEVER ALLOW PASSENGERS ON THE ATTACHMENT.

NEVER DIRECT DISCHARGE TOWARDS BYSTANDERS,

BUILDING, CARS ETC.

ALWAYS USE A DUST MASK WHEN WORKING IN DUSTY

CONDITIONS.

KEEP PLASTIC AWAY FROM INTENSE HEAT

AND OPEN FLAME.

229

Safety Decal: Safety Procedures

Decal: Walker Decal

Location: Discharge Chute

Location: Snowblower Housing

Part Number: 660988 (RAD)

Part Number: 5800-9

Part Number: 5809-2

134

servicing.

Shut off engine before

clothing away.

Keep hands,feet and

Rotating Auger:

Avoid Injury From

DANGER

Safety Decal: Rotating Auger

Location: Snowblower Housing

Part Number: 657762 (RAD)

Important Decal: Shear Bolts

Location: Inside Housing Behind Auger

Part Number: 2500574 (RAD)

USE SPECIAL AUGER AND

FAN SHEAR BOLTS ONLY.

ONE END DOWN

ONE END UP

SILVER, TWO GROOVES

GOLD, ONE GROOVE

#657295 #667786

TIGHTEN THE SHEAR BOLTS TO

A TORQUE OF 9 FT-LBS (12 N-M).

IMPORTANT

544

Assembly Instructions

1. Remove the rear shaft support from the chute

base lip and discard the existing bolt. Refer to

Install Rotation Worm Assembly to locate the

rear shaft support.

2. Place the plastic anti-friction insert over the

chute base as shown in Install Plastic Insert.

Only one position provides a perfect t.

Rear

Front

Nipple (Facing Up)

Install Plastic Insert

3. Insert the 1-5/16 in. (33 mm) (P/N I184) plastic

bushing into the tube weldment, then insert the

1-11/16 in. (43 mm) (P/N I186) plastic bushing

into the rear shaft support and place over the

shaft on the rotation worm as shown in Install

Rotation Worm Assembly.

4. Install the rotation worm assembly into the tube

weldment with the rear shaft support plate on

the underside of the chute base lip as shown in

Install Rotation Worm Assembly.

Tube Weldment

1-5/16 in. Bushing

1-11/16 in.

Bushing

Rotation Worm

Rear Shaft

Support

Install Rotation Worm Assembly

5. Install the chute over the plastic insert and se-

cure with four retaining plates as shown in In-

stall Chute and Retaining Plates, using two

(2) 1/4-20 x 3/4 in. bolts (F032), lock washers,

and 1/4-20 hex nuts (F381) in each of the four

(4) standard retaining plates. Tighten all bolts to

10 ft-lb (13.6 N•m).

Retaining Plates

Install Chute and Retaining Plates

6. Insert two (2) 5/16 x 1 in. carriage bolts (F169)

through each of the skid shoes from inside the

bend. Place a 3/8 SAE washer (F051), 5/16

split lock washer (F168), and 5/16-18 ESNA Nut

(F020) loosely on each bolt and place the bolt

heads through the round holes in the outer ends

of the bottom angle of the snowblower body as

shown in Install Skid Shoes. Adjust the skid

shoes to allow the required clearance under the

cutting edge. Slide the square shank portion of

the bolt head into the slot and tighten the nuts

securely. Refer to ADJUSTMENTS - Skid

Shoes in Maintenance section.

Snowblower

Housing

Carriage Bolts

Skid Shoe

Install Skid Shoes

Assembly Instructions

7. Install the hand guard on the chute, with the top

section inside the chute and the bottom section

outside the chute base ring. Place two (2) 1/4-

20 x 3/4 in. hex bolts (F032) through the chute

and the hand guard. Secure bolts with a 5/16

SAE washer (F049), and 1/4-20 hex nut (F381).

Position each bolt with the head on the outside

of the chute and the nut on the inside, and

torque bolts to 10 ft-lbs (13.6 N•m).

Hand Guard

Installing Hand Guard on Chute

8. Thoroughly clean the drive shaft yoke and

install a 1/4 x 1/4 x 1-1/2 in. key (F149) in the

drive shaft keyway as shown in Attach PTO

Drive Shaft Yoke to Snowblower Drive Shaft.

Drive Shaft

1/4 x 1/4 x 1-1/2 Key

Set Screw

1/4-20

Keps Nut

1/4 x 2-1/2

Hex Bolt

PTO Drive Shaft Yoke

Attach PTO Drive Shaft Yoke to Snowblower

Drive Shaft

9. Slide the drive shaft yoke over the drive shaft.

10. Secure the yoke to the drive shaft with a 1/4 x

2-1/4 in. hex bolt (F271) and 1/4-20 keps nut

(F004). Tighten the nut and the 3/8-16 x 3/4 set

screw (F318) securely over the key in the yoke.

11. Install one (1) 5/16-18 x 1/2 in. hex bolt on each

side of the PTO guard, and tighten securely.

Guard Mount

Bolt

PTO Guard

Install PTO Guard

Installation Instructions

1. Grease the drive shaft spline sliding surfaces and

slide the PTO coupler (tractor half) onto the shaft

as shown in Install PTO Coupler on Drive Shaft

photo.

Install PTO Coupler on Drive Shaft

2. Retract the spring-loaded quick disconnect ring

on the PTO Coupler and insert the Coupler In-

stallation Tool (provided in Owner’s Packet) as

shown in the photo below.

Coupler

Installation Tool

PTO Coupler

Tube

Retract Spring-Loaded

Quick Disconnect Ring

PTO Coupler Installation Tool

3. Insert the male quick hitch section of the imple-

ment hitch into the female socket of the snow-

blower as shown in Male to Female Hitch Con-

nection photo.

4. Lock the snowblower on the hitch using the

following instructions for either the H10 or H19

hitch:

H10: LOCKING/REMOVING IMPLEMENTS

Female Receiver

Male Hitch

Male to Female Hitch Connection

(H12 Snowblower Implement Shown)

Hitch Connected to Snowblower

All implements must be locked in place on the imple-

ment hitch before beginning any operation.

● Locking: Rotate the hitch lock lever fully for-

ward to the LOCKED position, and secure the

hitch latch with the linch pin as shown in Hitch

Lock Lever in “LOCKED” Position photo.

Linch Pin

Locking Lever

LOCKED

H10 Hitch Lock Lever in “LOCKED” Position

(View From Right Side of Tractor)

Installation Instructions

● Removing: Remove the linch pin from the

latch and move the hitch lock lever backward

to the UNLOCKED position as shown in Hitch

Lock Lever in “UNLOCKED” Position photo.

Locking Lever

UNLOCKED

H10 Hitch Lock Lever in “UNLOCKED” Position

(View From Right Side of Tractor)

H19: LOCKING/REMOVING IMPLEMENTS

● Locking: Rotate the hitch lock lever fully

backward to the LOCKED position, and secure

the lever with the lock pin as shown in Hitch

Lock Lever in “LOCKED” Position photo.

Lock Pin

Locking Lever

LOCKED

H19 Hitch Lock Lever in “LOCKED” Position

(View From Right Side of Tractor)

● Removing: Remove the lock pin, and move

the hitch lock lever forward to the UNLOCKED

position as shown in Hitch Lock Lever in “UN-

LOCKED” Position photo.

Locking Lever

UNLOCKED

H19 Hitch Lock Lever in “UNLOCKED” Position

(View From Right Side of Tractor)

5. Attach the PTO coupler to the tractor PTO shaft.

Remove the installation tool and make sure the

coupler is secured properly to the tractor PTO

shaft, and that the quick disconnect ring is in the

LOCKED position as shown in Quick Discon-

nect Ring in “Locked” Position photo (see

next page). After installation, pull on the PTO

coupler to check for security.

WARNING

The PTO shaft turns at high RPM. If the

coupler is not locked to the shaft at the

tractor end, or if the yoke at the snowblow-

er end is not secured properly, the drive

shaft can y loose with great force, capable

of causing serious injury or death.

IMPORTANT: DO NOT operate tractor with coupler

installation tool installed.

IMPORTANT: To prevent damage to the mower,

make sure the PTO quick disconnect is secure-

ly locked on the tractor, with the locking balls fully

seated in the groove and the ring in the locked posi-

tion (refer to Quick Disconnect Ring in “Locked”

Position). After installation pull on the PTO coupler

to check for security.

Installation Instructions

Coupler Ring in

Released Position

PTO Coupler

U-Joint

PTO Drive

Shaft

Quick Disconnect Ring in “Released” Position

Internal Balls

Locked on Shaft

PTO Drive

Shaft

Coupler Ring in

Locked Position

PTO Coupler

U-Joint

Quick Disconnect Ring in “Locked” Position

H19: FLOAT FUNCTION ADJUSTMENT

● NON-FLOATING: Insert the clevis pin (refer to

Non-Float Setting With Clevis Pin Installed)

through the rear actuator mount and secure with

the bowtie cotter pin. Install the clevis pin to al-

low for downward pressure on the implement.

● FLOATING: Remove the bowtie cotter pin, and

remove the clevis pin from the rear actuator

mount (refer to Float Setting With Clevis Pin

Removed). Removing the clevis pin will allow a

free oating implement.

Actuator Motor

Clevis Pin

Non-Float Setting With Clevis Pin Installed

Actuator Motor

Clevis Pin

Removed

Float Setting With Clevis Pin Removed

6. Attach the parallel bar to the female hitch and

the implement adaptor using the two clevis pins

and spring clips. Adjust the length of the paral-

lel bar by turning either end clockwise to short-

en, or counterclockwise to lengthen as needed

to level the snowblower.

Rear Clevis

Attach

Parallel Bar

Front Clevis

Attach

Attach Parallel Bar

Installation Instructions

7. Insert the chute rotation handle into the rotation

worm. Align the holes and lock in place with a

1/4 x 1 in. socket head cap screw (F036) and

nylon locknut (F005) as shown in Install Chute

Rotation Handle photo.

Rotation Handle

Install Chute Rotation Handle

8. Install the plastic handle grip on the chute rota-

tion handle. Refer to Install Handle Grip photo.

Handle Grip

Install Handle Grip

9. For GHS (Grass Handling System) equipped

Walker tractors, install a blower intake cover

(P/N 5595-2) in the blower intake tube. The

cover “unloads” the blower and seals the intake

to effectively eliminate power loss and noise

when the blower is not being used.

10. Counterweight should be installed on the tail

of the tractor for stability when transporting the

tractor with the snowblower in raised position.

Optional tail weights for the various tractor mod-

els are available from your Walker dealer, or a

sandbag or similar weight may be used.

Blower Intake Cover

GHS Blower Intake Cover

Operating Instructions

PREOPERATION CHECKLIST

Before operating the snowblower for the rst time,

and as a routine before daily operations, it is im-

portant to make sure the machine is properly pre-

pared and ready for operation. The following is a list

of items to be checked. For machines with frequent

operation, some of these items will not need to be

checked every day, but the operator should be

aware of the condition of each.

TRACTOR

CHECK TRACTOR PREOPERATING CHECK-

LIST

Refer to the appropriate Tractor Operator’s

Manual.

CHECK TRACTOR TAILWEIGHT

Make sure sufcient weight has been securely

installed on rear of tractor (approximately 80 lbs.

on most tractor models).

CHECK OPTIONAL TIRE CHAINS

Tire chains should always be used when operat-

ing the machine in icy conditions. If the tractor is

equipped with the optional tire chains, make

sure the chains are in good condition and are

installed properly.

IMPLEMENT HITCH

CHECK LIFT SWITCH OPERATION

Raise and lower the implement hitch to make

sure the lift switch and linear actuator operate

properly.

CHECK HITCH LOCKING LEVER

Inspect the locking mechanism for secure

mounting of snowblower on hitch. Refer to

Hitch Locking Lever in locked position in step

4 of Installation Instructions.

SNOWBLOWER

CHECK SKID SHOE FOR WEAR AND PROP-

ER ADJUSTMENT

See ADJUSTMENTS - Snowblower Skid

Shoes in the Maintenance section of this manu-

al.

ADJUST THE PARALLEL BAR SO THAT THE

SNOWBLOWER RUNS LEVEL.

See step 6 in Installation instructions

CHECK CUTTING EDGE

Make sure the cutting edge is not damaged or

worn beyond limits. Refer to REPLACING AND

REPAIRING PARTS - Snowblower Cutting

Edge in the Maintenance Instructions.

CHECK AUGER AND IMPELLER

● Make sure the auger and impeller are clear

of snow and/or ice.

● Make sure the auger and impeller are free

to rotate.

● Check that the auger ighting and impeller

blades are in good condition and not bent.

CHECK CHUTE AND DEFLECTOR

● Make sure the chute and deector are not

clogged with snow and/or ice.

● Turn the chute rotation handle and rotate

the chute. The chute should rotate freely.

● Loosen the deector position knobs to raise

and lower the deector. The deector

should move freely. Retighten deector po-

sition knobs with the deector in the desired

position.

CHECK GEARBOX OIL LEVEL

Inspect for any sign of an oil leak. Refer to LU-

BRICATION - Snowblower Gearbox in the

Maintenance Instructions of this manual.

CHECK SHEAR BOLTS

Check the three (3) shear bolts, one on each au-

ger section, and one between the fan and gear-

box for proper tightness, approximately 8 lb-ft

(11 N•m).

CHECK REDUCTION CHAIN

Refer to LUBRICATION - Snowblower Reduc-

tion Chain in the Maintenance Instructions.

Refer to ADJUSTMENTS - Snowblower Re-

duction Chain Tension in the Maintenance In-

structions.

Page is loading ...

Walker H17 50" Snowblower User manual

Brand: Walker

Model: H17 50" Snowblower

Category: Snow throwers

Type: User manual

This manual is also suitable for

H12 42" Snowblower

Download PDF

report

Walker H17 50" Snowblower User manual

This manual is also suitable for

Walker H17 50" Snowblower User manual

Related papers

Other documents