Walker H10, H19 Implement Hitch Mount User manual

Brand: Walker

Model: H10, H19 Implement Hitch Mount

Category: Lawnmowers

Type: User manual

Assembly, Attaching, Removing, Operation and Maintenance

H10 compatible with Models C, D, T

H19 compatible with Model H

Please Read and Save These Instructions

For Safety, Read All Assembly and Operation Instructions

Prior to Operating Attachment

H10 & H19 Implement Hitch Mount

Operator’s Manual

H10 Beginning S/N: 2018-6541

H19 Beginning S/N: 2017-6226

P/N: 6618-10

Foreword

Thank you. . .for purchasing a Walker Implement Hitch Mount. Every effort has been made to provide you with

the most reliable machine on the market, and we are sure you will be among our many satised customers. If for

any reason this product does not perform to your expectations, please contact your local dealer. Every customer is

important to us. Your satisfaction is our goal.

Please. . .read this manual thoroughly! Before you operate your machine, please read this entire manual. Some

of the information is crucial for proper operation - it will help protect your investment and ensure that the machine

performs to your satisfaction. Some of the information is important to your safety, and must be read and understood

to help prevent possible injury to the operator or others. If anything in this manual is confusing or hard to understand,

please contact your local authorized dealer or call our service department, at (970) 221-5614, for clarication before

operating or servicing this machine.

All shields and guards must be in place for the proper and safe operation of this machine. Where they are

shown removed in this manual, it is for illustration purposes only. Do not operate this machine unless all shields

and guards are in place.

Walker Mfg. Co. is continually striving to improve the design and performance of its products. We reserve the right to

make changes in specications and design without thereby incurring any obligation relative to previously manufactured

products.

Sincerely,

WALKER MANUFACTURING

COMPANY

Bob Walker, President

General Information 1

HIGHLIGHTED INFORMATION 1

GLOSSARY 1

IDENTIFYING NUMBER LOCATIONS 1

SERVICING OF LINEAR ACTUATOR 2

UNIT DESCRIPTION 2

Specications 3

H10 3

H19 3

Component Identication 4

Safety Instructions 6

BEFORE OPERATING 6

OPERATING 7

MAINTENANCE 8

SAFETY, CONTROL AND

INSTRUCTION DECALS 10

Assembly Instructions 11

IMPLEMENT HITCH WIRING 11

H10 Implement Hitch Wiring: MC, MD, MT 11

H19 Implement Hitch Wiring - MH Only 13

HITCH INSTALLATION ON TRACTOR 16

Attaching H10 Implement Hitch to

MC, MD, or MT 16

Attaching H19 Implement Hitch to MH 17

Operating Instructions 18

TOGGLE SWITCH 18

H10: LOCKING/REMOVING IMPLEMENTS 18

H19: LOCKING/REMOVING IMPLEMENTS 18

H19: FLOAT FUNCTION ADJUSTMENT 19

REMOVAL AND STORAGE INSTRUCTIONS 19

Removing Hitch 19

End of Season Storage 20

Maintenance Instructions 20

H19 HITCH LOCK TENSION ADJUSTMENT 20

LUBRICATION 22

Parts List/Diagram

H10 25

H19 27

MAINTENANCE AND SERVICE

RECORDS SHEET 29

Warranty 32

Table of Contents

General Information

HIGHLIGHTED INFORMATION

Walker Manufacturing recommends that any service

requiring special training or tools be performed by an

authorized Walker Mower Dealer. There are several

general practices to be aware of in the area of safety.

Most accidents associated with the operation or

maintenance of a Walker Tractor are caused by dis-

regarding basic safety precautions or specic warn-

ings. Such accidents, in most cases, can be pre-

vented by being aware of the dangers present.

Information of special importance has been high-

lighted in bold type in this manual. Refer to Safety

Instructions for the meanings of DANGER, WARN-

ING, CAUTION, IMPORTANT, and NOTE.

GLOSSARY

There are many terms that are either unique to this

equipment or that are used as acronyms. The follow-

ing terms and their denitions will help while using this

manual:

● FORWARD SPEED CONTROL (FSC) controls

the maximum forward speed of the tractor; func-

tioning as a cruise control.

● IMPLEMENT refers to the dozer blade, rotary

broom, two-stage snowblower, or debris blower

used with the tractor with an implement hitch

installed.

● LEFT HAND (LH) refers to the left-hand side of

the tractor when the operator is seated facing

forward in the tractor seat.

● MACHINE consists of the implement installed

on the tractor, functioning as a single unit.

● POWER TAKE-OFF (PTO) transmits engine

power to run the cutter blades and GHS blower.

● RIGHT HAND (RH) refers to the right-hand side

of the tractor when the operator is seated facing

forward in the tractor seat.

● STEERING LEVERS steer the tractor by con-

trolling the two transaxles.

● TRACTOR is the prime mover, including the en-

gine, drivetrain, operator seat, and controls to

operate the mower.

IDENTIFYING NUMBER LOCATIONS

The implement hitch serial number is afxed to the

center of the hitch frame weldment on the H10, and

the left hand side of the main frame weldment on the

H19. Model and serial numbers are helpful when

obtaining replacement parts and maintenance as-

sistance. For ready reference, please record these

numbers in the space provided.

Implement Hitch Model No.

Implement Hitch Serial No.

Date of Purchase

Refer to the Operator’s manual that accompanies the

tractor for the tractor serial number.

Serial Number

H10 Implement Hitch Serial Number Location

(Top View)

Serial Number

H19 Implement Hitch Serial Number Location

(Rear LH View)

General Information

SERVICING OF LINEAR ACTUATOR

Only routine maintenance and general service in-

structions are provided in this manual. For service of

the linear actuator during the limited warranty period,

contact your authorized Walker dealer. Any unau-

thorized work done on the linear actuator during the

warranty period may void the warranty. If you have

any difculty nding an authorized outlet or obtaining

warranty service, please contact our Service Depart-

ment for assistance:

Walker Manufacturing Company

5925 E. Harmony Road

Fort Collins, CO 80528

1-970-221-5614

www.walker.com

UNIT DESCRIPTION

The implement hitch is required to mount imple-

ments on the tractor. The hitch mounts on the trac-

tor in place of the mower deck in less than a minute.

Each implement slides on the male hitch and easily

locks in place. The hitch assembly also includes op-

erator footrests and an electric power lift. The lift

control switch is mounted on the FSC lever for con-

venient operator use, and is powered by the linear

actuator on the implement hitch.

Specications

IMPLEMENT HITCH

MODEL H10 H19

Height in. (cm) 10 (25) 12.75 (32)

Width in. (cm) 33.5 (85) 37 (94)

Length in. (cm) 30 (76) 26 (66)

Overall Length Installed on Tractor in. (cm)* 72.25 (184) 88.5 (225)

Weight lb (kg) 64 (29) 79 (36)

Lift 12 Volt DC Electric Ram Linear Actuator, Operated by Toggle

Switch Mounted on FSC Lever

NOTE: The manufacturer reserves the right to make changes in specications shown herein at any time without

notice or obligation.

* H10 installed on C19i; H19 installed on H27i

Component Identication

H10 Implement Hitch Top View (Not Installed)

Linear Actuator

Electrical Connector

Mount Adjustment Bolt

Jam Nut

Mounting Tube

Footrest

Male Quick

Hitch Latch

PTO Shield

Linchpin

Safety

Chain

Male Hitch Assembly

Footrest

Mounting Tube

Hitch Lock

Lever

Component Identication

H19 Implement Hitch Rear LH View (Not Installed)

Linear Actuator

Electrical Connector

Male Hitch

Assembly

Hitch Lock

Lever

Attach Point

for H12/H17

Snowblower

Installation

Lock Pin

Chassis Support

Strap

Nerf Bar

Mounting Tube

Hitch Latch

Linkage

Footrest

PTO Shield

Footrest

Nerf Bar

Chassis Support

Strap

Mounting Tube

Safety Instructions

Pay particular attention to any information labeled

DANGER, WARNING, CAUTION, IMPORTANT, and

NOTE in this manual.

When you see the Safety Alert Symbol ( ), read,

understand, and follow the instructions. Fail ure to

comply with safety instructions may result in personal

injury.

The seriousness or degree of importance of each type

of information is dened as follows:

DANGER

An IMMEDIATE hazard that WILL result in se-

vere personal injury or DEATH, if warning is

ignored and proper safety precautions are

not taken.

WARNING

A POTENTIAL hazard that COULD result in

severe personal injury or DEATH, if warning

is ignored and proper safety precautions are

not taken.

CAUTION

Possible hazards or unsafe practices that

MAY result in MODERATE personal injury or

property damage, or machine damage, if

warning is ignored and proper safety pre-

cautions are not taken.

IMPORTANT: Identies mechanical information

demanding special attention, since it deals with the

possibility of damaging a part or parts of the machine.

NOTE: Identies information worthy of special

attention.

Walker Manufacturing cannot predict every potentially

dangerous situation. Therefore, items labeled as such

in this manual do not cover all conceivable situations.

Any person using procedures, tools, or control tech-

niques not recommended by Walker Manufacturing

must take full responsibility for safety.

The Walker Rider Lawnmower has been designed

with many safety features to protect the operator from

personal harm or injury. However, it is necessary for

the operator to use safe operating procedures at all

times. Failure to follow safety instructions con-

tained in this manual may result in personal injury

or damage to equipment or property.

If you have any questions concerning setup, opera-

tion, maintenance, or safety, please contact your au-

thorized Walker Mower dealer or call Walker Manu-

facturing Company at (970) 221-5614.

BEFORE OPERATING

1. Read and understand the contents of this Op-

erator’s Manual before starting and operating

the machine. Become thoroughly familiar with all

machine controls and how to stop the machine

and disengage the controls quickly. Replacement

Operator’s Manuals are available by sending the

Model and Serial Number to:

Walker Manufacturing Company

5925 East Harmony Road

Fort Collins, CO 80528

2. Never allow children to operate rider mower.

Do not allow adults to operate without proper in-

struction.

3. Do not allow anyone other than the operator on

the machine.

4. Keep everyone, especially children and pets, a

safe distance away from the area of operation.

Do not mow with bystanders in the area.

5. Do not operate the machine barefoot or wearing

sandals, sneakers, tennis shoes, or similar light-

weight footwear. Wear substantial protective

footwear.

6. Do not wear loose tting clothing that could get

caught in moving parts. Do not operate this ma-

chine while wearing shorts; always wear ade-

quate protective clothing, including long pants.

Wearing safety glasses, safety shoes, and a hel-

met is advisable and required by some local ordi-

nances and insurance regulations.

Safety Instructions

7. Prolonged exposure to loud noise can cause im-

pairment or loss of hearing. Operator hearing

protection is recommended. Wear a suitable

hearing protective device, such as earmuffs or

earplugs.

8. Keep all protective shields and safety devic-

es in place. If a protective shield, safety device,

or decal is damaged, unusable, or missing, re-

pair or replace it before operating the machine.

9. Be sure interlock switches are functioning

correctly, so the engine cannot be started un-

less the Forward Speed Control lever is in the

NEUTRAL-PARK position, and the PTO clutch

is in the DISENGAGED position. Also, the en-

gine should stop if the operator lifts off the seat

with either the Forward Speed Control (FSC)

out of the NEUTRAL-PARK position or the PTO

clutch in the ENGAGED position.

10. Handle gasoline with care. Gasoline is highly

ammable and its vapors are explosive:

a. Use an approved fuel container.

b. Never add fuel to a running engine or hot

engine (allow hot engine to cool several

minutes).

c. Keep matches, cigarettes, cigars, pipes,

open ames, or sparks away from the fuel

tank and fuel container.

d. Always ll the fuel tank outdoors using care.

Fill to about one inch from the top of the tank.

Use a funnel or spout to prevent spilling.

e. Replace the machine fuel cap and container

cap securely and clean up any spilled fuel

before starting the engine.

11. Never attempt to make any adjustments while

the engine is running, except where specical-

ly instructed to do so.

12. The snow or leaves can sometimes hide objects

that might clog the snowblower or debris blower

chute, or otherwise cause damage. Clear the

area of doormats, sleds, boards, wires and other

debris.

13. The electrical system battery contains sulfuric

acid. Avoid any contact with skin, eyes, and

clothing. Keep the battery and acid out of reach

of children.

WARNING

This product can expose you to

chemicals including Phenylethane which is

known to the State of California to

cause cancer, and N-Methyl-2-Pyrrolidone,

which is known to the State of California

to cause birth defects or other reproductive

harm. For more information go to www.

P65Warnings.ca.gov.

OPERATING

NOTE: Refer to your tractor Operator’s Manual for

safety instructions for operating the tractor.

1. Operate the machine only in daylight or in

good articial light with good visibility of areas

being cleaned.

2. Sit on the seat when starting the engine and op-

erating the machine. Keep feet on footrests at

all times when the tractor is moving and/or the

implement is operating.

3. For a beginning operator, learn to steer (ma-

neuver) the tractor with a slow engine speed

before attempting any implement operation.

Be aware that, with the front mounted implement

conguration, the back of the machine swings to

the outside during turns.

DANGER

Do not operate around overhanging tree

branches or bushes at the same height as

the operator’s torso and head where inad-

vertent contact may cause injury.

4. Remember, for an emergency stop, the forward

motion of the tractor can always be stopped by

pulling the Forward Speed Control (FSC) into the

NEUTRAL-PARK position.

Safety Instructions

5. In case the transmission drive belt breaks during

operation, and if the machine is on a slope, the

machine will freewheel down the slope. To

maintain control, immediately (1) Release the

steering levers and simultaneously (2) Move the

FSC to the NEUTRAL-PARK position. When

the machine is stopped or moving slowly, en-

gage the parking brake.

NOTE: The emergency stop procedure is exact-

ly the same procedure used to normally stop and

park the machine.

6. Disengage the PTO clutch and put the FSC in

the NEUTRAL-PARK position before starting

the engine (an ignition interlock switch normally

prevents starting of the tractor if these controls

are in the OPERATING position).

7. Do not operate the machine if the operator

presence safety switch system is not work-

ing. Verify proper operation by having the oper-

ator lift off the seat with the engine running and

moving two controls, one at a time; (1) Move the

FSC lever out of the NEUTRAL-PARK position,

and (2) Engage the PTO Clutch. Moving either

control should stop the engine immediately.

8. Do not run the engine in a conned area

without adequate ventilation. Exhaust fumes

are hazardous and can be deadly.

9. Do not carry passengers - maximum seating

capacity is one (1) person.

10. Avoid sudden starts or stops. Before backing

the machine up, look to the rear to be sure no

one is behind the machine. Watch carefully for

trafc when crossing or working near roadways.

11. When moving forward, do not suddenly put the

tractor in reverse by rapidly pulling on the steer-

ing levers, especially when going downhill, as

this can lift the tractor tail wheel off the ground

and set up a bucking motion due to operator

overcontrol. If bucking does occur, immediate-

ly stop the bucking action by pulling the For-

ward Speed Control (FSC) lever into the NEU-

TRAL-PARK position.

12. Disengage the PTO clutch when transporting

the machine.

13. Do not operate across the face of slopes. Use

extreme caution when changing direction on

slopes. Do not attempt to operate on steep

slopes.

14. Never adjust gauge wheels or skid shoes with

the engine running. Before adjusting height or

servicing, disengage the PTO clutch, stop the

engine, and remove the ignition key. Wait for

all movement to stop before getting off the seat.

NOTE: The PTO brake should stop drive line

rotation within ve (5) seconds of disengaging

the PTO clutch. If the brake is not function-

ing properly, have it repaired by an authorized

dealer immediately.

15. If the implement strikes a solid object or the ma-

chine begins to vibrate abnormally, immediately

disengage the PTO clutch, stop the engine,

and wait for all moving parts to stop. Dis-

connect the fuel solenoid wire [diesel engines]

or the spark plug wire(s) [gasoline engines] to

prevent accidental starting. Thoroughly inspect

the implement and repair any damage before re-

starting the engine and operating the machine.

Make sure implement components are in good

condition and all bolts are tight.

16. Do not touch the engine or mufer while the

engine is running or immediately after stopping

the engine. These areas may be hot enough to

cause serious burns.

17. When leaving the machine unattended, disen-

gage the PTO clutch, stop the engine, and re-

move the ignition key.

MAINTENANCE

NOTE: Refer to your tractor Operator’s Manual for

safety instructions for tractor maintenance.

1. To prevent accidental starting of the engine

when servicing or adjusting the machine, re-

move the key from the ignition switch and dis-

connect the fuel solenoid wire [diesel engines]

or the spark plug wire(s) [gasoline engines].

2. To reduce re hazards, keep the engine free of

grass, leaves, excessive grease, and dirt.

3. Keep all nuts, bolts, and screws tight to ensure

the machine is in a safe, working condition.

4. Perform only maintenance instructions de-

scribed in this manual. Unauthorized mainte-

nance operations or machine modications may

result in unsafe operating conditions.

5. If the engine must be running to perform a main-

tenance adjustment, keep hands, feet and

clothing away from moving parts. Do not

wear jewelry or loose clothing.

Safety Instructions

6. Always use proper engine service manuals

when working on the engine. Unauthorized

maintenance operations or modications to the

engine may result in unsafe operating conditions.

7. Altering the machine in any manner which ad-

versely affects its operation, performance, dura-

bility or use will VOID the warranty and may

cause hazardous conditions.

8. Never attempt to disconnect any safety devices

or defeat the purpose of these safety devices.

9. Do not change the engine governor settings or

overspeed the engine. The governor has been

factory-set for maximum-safe engine operating

speed.

10. Use genuine factory replacement parts. Sub-

stitute parts may result in product malfunction

and possible injury to the operator and/or others.

IMPORTANT: Keep all applicable manuals im-

mediately accessible to anyone who may op-

erate or service this machine.

Safety Instructions

SAFETY, CONTROL, AND INSTRUCTION DECALS

Safety, Control, and Instruction Decals are installed on the machine;

if any are missing, illegible, or damaged, a replacement should be ordered and installed before

putting the machine into operation. The Decal Part Number is listed below and in the Parts Manual.

DANGER

ROTATING DRIVELINE

KEEP AWAY!

CONTACT CAN CAUSE DEATH

IMPORTANT

When raising tractor body, the PTO shield must be closed or in the down

position and the implement in the lowered position. Open the PTO shield ONLY for connecting

or disconnecting driveline.

– DO NOT OPERATE WITHOUT –

ALL DRIVELINE, TRACTOR AND EQUIPMENT SHIELDS IN PLACE.

DRIVELINES SECURELY ATTACHED AT BOTH ENDS.

DRIVELINE SHIELDS THAT TURN FREELY ON DRIVELINE.

7822

Safety Decal: Rotating Driveline

Location: PTO Shield

Part Number: 7822

ADJUST TENSION ON LOCKING ARM AFTER

INITIAL 15 MIN. OF USE IF NECESSARY

TENSION ADJUSTMENT CLEVIS

LOCKING PIN

SEE OWNERS MANUAL FOR ADDITIONAL

ADJUSTMENT/INSTALLION INFORMATION

6621-13

Adjustment Decal: Locking Mechanism

H19 ONLY

Location: PTO Shield

Part Number: 6621-13

INSTALLATION INSTRUCTIONS

• INSERT SUBFRAME INTO ATTACHEMENT COMPLETELY.

• LOCK IN PLACE BY MOVING LEVER FORWARD TO “LOCK”

POSITION AND SECURE WITH LINCH PIN.

• IF EQUIPEED WITH P.T. O. DRIVELINE, CONNECT TO

TRACTOR P.T. O. AND LOCK IN PLACE.

• IF EQUIPPED WITH LIFT ASSIST SPRINGS, LIFT THE

ATTACHEMENT AND ATTACH SPRINGS.

UNLOCK

LOCK

113

Adjustment Decal: Locking Mechanism

H10 ONLY

Location: Male Hitch

Part Number: I393

RAISE

IMPLEMENT

HITCH

LOWER

6632

Operation Decal: Toggle Switch

Location: Forward Speed Control

Part Number: 6632

IMPORTANT

WHEN INSTALLING IMPLEMENT ADAPTOR

ADJUST BOLT HEAD TO CONTACT CROSS MEMBER

OF TRACTOR FRAME-SECURE WITH LOCKNUT

6618

Adjustment Decal: 3/4 in. Bolt - H10 ONLY

Location: Frame, H10 Implement Hitch

Part Number: 6618

Assembly Instructions

IMPLEMENT HITCH WIRING

Before installing the implement hitch on the tractor,

the lift control switch and wiring are installed using

the following steps:

H10 Implement Hitch Wiring: MC, MD, MT

1. Attach the toggle switch mounting bracket to the

FSC lever using two (2) 10-24 x 1/2” bolts and

Keps nuts as shown in Attach Toggle Switch

and Secure Wire Harness (H10) illustration.

2. Install the toggle switch on the mounting brack-

et, placing the switch terminals toward the front

of the mower.

3. If a hole is not present in the location shown in

Drilling Hole for Cable Clamp, drill a 3/16 in.

hole in the right front body to attach the cable

clamp. Measure 1-3/4 in. from the edge of the

body, and 7/8 in. down from the top of the body

as shown in Drilling Hole for Cable Clamp.

7/8”

1-3/4”

Drilling Hole for Cable Clamp

4. Connect the wiring harness to the switch and

route the harness as shown in Attach Toggle

Switch and Secure Wire Harness (H10)

illustration. Attach the wiring harness to the

tractor body using the two wiring clamps, two 10-

24 x 3/8” bolts and Keps nuts as shown. Also,

attach the ground wire (green) ring terminal to

the inside of the body using the lower cable

clamp mounting bolt.

NOTE: Grind the paint away under the ground

wire ring terminal to ensure a good ground

connection.

5. Connect the harness red wire to the load side of

the circuit breaker mounted on the bracket be-

hind the battery as shown in Connect Power

Wire to Circuit Breaker photo.

Power Wire

(Red)

Circuit Breaker

(Load Side)

Connect Power Wire to Circuit Breaker

(MT25i Shown)

6. Install P/N 6632 Toggle Switch Decal as shown

in FSC Lever with Lift Control Switch photo.

Toggle Switch

Decal P/N 6632

FSC Lever with Lift Control Switch

Assembly Instructions

HARNESS RUNS ON

OUTSIDE OF BODY

REUSE

P/N 6632 DECAL

ATTACH POWER WIRE (RED) TO

TERMINAL ON CIRCUIT BREAKER

ATTACH GREEN GROUND WIRE

INSIDE BODY TO HARNESS CLAMP BOLT

TWO (2) CLAMPS

SECURE HARNESS

NOTE: Applies to Models C, D, and T ONLY.

Attach Toggle Switch and Secure Wire Harness (H10)

Assembly Instructions

H19 Implement Hitch Wiring - MH Only

1. Attach the toggle switch mounting bracket to the

FSC lever using two (2) 10-24 x 1/2” bolts and

Keps nuts as shown in Attach Toggle Switch

illustration.

ATTACH RED POWER WIRE TO PURPLE WIRE

ON LOAD SIDE OF CIRCUIT BREAKER

ATTACH GREEN GROUND WIRE

INSIDE BODY TO HARNESS CLAMP BOLT

HARNESS RUNS ON INSIDE OF BODY

Attach Toggle Switch

2. Install the toggle switch on the mounting bracket,

placing the switch terminals toward the back of

the mower.

3. Connect the wiring harness to the switch and

route the harness through the FSC slot ahead

of the FSC lever as shown in Wire Harness

Routing (H19) photo. Route harness along front

of chassis under the steering levers and through

the hole in the rubber debris guard as shown

in the Wire Harness Through Debris Guard

photo.

NOTE: It may be necessary to push the wires

out of the harness plug to feed the wire harness

through the hole in the debris guard.

Feed Wire Harness

Through FSC Slot

Wire Harness Routing (H19)

Feed Wire Harness

through Debris Guard

Wire Harness Through Debris Guard

4. Secure the harness using a cable clamp as

shown in Install Wire Harness and Toggle

Switch (H19) illustration. Attach the ground wire

ring terminal using the same bolt as the cable

clamp as shown in Wire Harness Ground Wire

Installation photo.

Install Ground Wire

on Cable Clamp

Cable Clamp

Wire Harness

Wire Harness Ground Wire Installation

NOTE: Grind the paint away under the cable

clamp to ensure a good ground connection.

5. Using the supplied splice tap, connect the red

wire on the harness to the purple wire running

between the ignition switch and the 20 amp cir-

cuit breaker.

6. Install P/N 6632 Toggle Switch Decal as shown in

Install Wire Harness and Toggle Switch (H19)

illustration.

Assembly Instructions

Install Wire Harness and Toggle Switch (H19)

NOTE: Applies to Model H ONLY.

RUN HARNESS THROUGH

HOLE IN DEBIS GUARD

ATTACH RED POWER WIRE TO PURPLE WIRE

ON LOAD SIDE OF CIRCUIT BREAKER

P/N 6632 Decal

ATTACH GREEN GROUND WIRE

INSIDE BODY TO HARNESS CLAMP BOLT

HARNESS RUNS ON INSIDE OF BODY

Implement Hitch Wiring Schematic

Actuator Switch

Purple

Model H

Tractors

(Chassis GND)

Green

Red

Wire Harness

Assembly

Model C, D, and T

Tractors

Red

Actuator

30 AMP

CIRCUIT

BREAKER

20 AMP

CIRCUIT BREAKER

Implement Hitch Wiring Schematic

Installation Instructions

HITCH INSTALLATION ON TRACTOR

Attaching H10 Implement Hitch to MC, MD, or MT

1. Remove the mower deck from the tractor, if nec-

essary. Refer to the appropriate Tractor Opera-

tor’s Manual.

2. Lightly grease both support arms on the tractor.

Refer to Install Hitch Pins photo for location of

the support arms.

3. Engage the hitch mounting tube sockets on the

support arms. Lift the hitch so the support arms

are level, and slide the implement hitch complete-

ly onto the support arms.

4. Install a hitch pin through the hole on the end of

each support arm to lock the hitch in place as

shown in Install Hitch Pins to Secure Imple-

ment Hitch photo. Two hitch pins are included in

the Owner’s Packet of materials.

Install Hitch Pins

Install Hitch Pins to Secure Implement Hitch

IMPORTANT: If the tractor body needs to be

raised, the PTO shield must be in the closed or

down position and the implement must be in the

lowered position. The only time the PTO shield

should be open or raised is when connecting or

disconnecting the PTO driveline for the rotary

broom, snowblower, or debris blower.

PTO Shield

in CLOSED

Position

Hitch Pins Lock Hitch

on Support Arms

PTO Shield in CLOSED Position

5. Loosen the 3/4-10 jam nut on the back end of the

implement hitch. Adjust the 3/4-10 x 2” hex bolt

until it contacts the cross-member of the tractor

frame. Securely tighten the 3/4-10 jam nut to pre-

vent the bolt from moving.

3/4-10

Jam Nut

3/4-10 x 2”

Hex Bolt

Actuator

(Ref)

Implement Hitch Jam Nut Adjustment

IMPORTANT: This adjustment will need to be

made only once if the same tractor and hitch are

used together. If the hitch will be used on more

than one tractor, this adjustment will be required

every time the hitch is mounted on a different

tractor.

6. After the hitch is installed, complete the wiring by

connecting the wiring harness to the actuator mo-

tor of the implement hitch.

7. Raise and lower the hitch a few times to check

the operation and make sure it moves smoothly.

If the hitch is not working with the switch, make

sure the wiring harness ends are connected prop-

erly and securely. Refer to the Implement Hitch

Wiring Diagram illustration.

(continued on next page)

Installation Instructions

● Move the implement lift switch backward to

raise the implement hitch to the UP position.

● Move the implement lift switch forward to

lower the implement hitch to the DOWN

position.

IMPORTANT: When the hitch reaches the full

raised or lowered position, the power ram clutch

will make a ratcheting sound. Release the toggle

switch as soon as this sound is heard. DO NOT

operate the ram with the clutch ratcheting for

an extended time as this will cause extra wear on

the clutch mechanism.

Attaching H19 Implement Hitch to MH

1. Remove the mower deck from the tractor, if nec-

essary. Refer to the appropriate Tractor Opera-

tor’s Manual.

2. Lightly grease both support arms on the tractor.

Refer to Implement Hitch Installed on Support

Arms for location of the support arms.

3. Engage the hitch mounting tube sockets on the

support arms. Slide the implement hitch com-

pletely onto the support arms.

4. Install a linch pin through the hole on the end of

each support arm to lock the hitch in place as

shown in Implement Hitch Installed on Support

Arms.

5. Using two (2) 3/8-16 ESNA nuts, install the chas-

sis support straps as shown in Implement Hitch

Installed on Support Arms photo.

6. After the hitch is installed, complete the wiring by

connecting the wiring harness to the actuator mo-

tor of the implement hitch.

7. Raise and lower the hitch a few times to check the

operation and make sure it moves smoothly. If the

hitch is not working with the swtich, make sure the

wiring harness ends are connected properly and

securely. Refer to the Implement Hitch Wiring

Diagram illustration.

8. Move the implement lift switch backward to raise

the implement hitch to the UP position.

9. Move the implement lift switch forward to lower

the implement hitch to the DOWN position.

IMPORTANT: When the hitch reaches the full

raised or lowered position, the power ram clutch

will make a ratcheting sound. Release the toggle

switch as soon as this sound is heard. DO NOT

operate the ram with the clutch ratcheting for

an extended time as this will cause extra wear on

the clutch mechanism.

Chassis Support

Strap

Pin slides into

existing hole in

chassis

Support Arm

Linch Pin

Implement Hitch Installed on Support Arms

Page is loading ...

Walker H10, H19 Implement Hitch Mount User manual

Brand: Walker

Model: H10, H19 Implement Hitch Mount

Category: Lawnmowers

Type: User manual

Download PDF

report

Walker H10, H19 Implement Hitch Mount User manual

Walker H10, H19 Implement Hitch Mount User manual

Related papers

Other documents