Teltone M-395-D-01 User manual

Brand: Teltone

Model: M-395-D-01

Type: User manual

This manual is also suitable for

Substation Line Sharing Switch

(SLSS)

M-395 and M-396

Product Manual

40-400-00031, Rev. A

Note

This manual covers Models M-395-A-02, M-396-A-02, M-395-B-01, M-396-B-01, M-395-D-01,

M-396-D-01, M-395-E-01, and M-396-E-01.

Trademarks

Teltone is a registered trademark of Teltone Corporation.

Windows is a registered trademark of Microsoft Corporation.

Other company and product names may be trademarks or

registered trademarks of their respective owners.

Teltone Corporation

Bothell, Washington 98021 USA

Customer Service: 425-951-3388

Technical Support: 425-951-3390

Fax: 425-487-2288

Email: [email protected]

Website: www.teltone.com

Contents

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i

About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Revision Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Conventions Used In This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Chapter 1: Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Where To Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Table 1 LED Indicators on the SLSS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Chapter 2: Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Figure 1 Typical SLSS Application. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Chapter 3: Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Are You Ready? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installing the SLSS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Figure 2 Installing the Central Office Telephone Line . . . . . . . . . . . . . . . . . . 5

Figure 3 Substation Line Sharing Switch (SLSS) . . . . . . . . . . . . . . . . . . . . . . . 6

Figure 4 SLSS Wiring Example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Install Polling Controller (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Setup Standalone Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Chapter 4: Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Programming Tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Setup for Remote Programming with a Polling Controller . . . . . . . . . . . . . 12

Example: Remote Programming with Polling Controller . . . . . . . . . . . . . . 13

Setup for Local Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Example: Local Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Setup SLSS Standalone Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Example: Standalone Local Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Access Standalone Remote Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Example: Standalone Remote Programming . . . . . . . . . . . . . . . . . . . . . . . . . 17

Teltone ® is a registered trademark of Teltone Corporation.

Reference Manual Contents

40-400-00031, Rev. A Page i

Example: Standalone Call with Post Call Routing. . . . . . . . . . . . . . . . . . . . . 18

Example: Standalone Call with Post Answer Transfer . . . . . . . . . . . . . . . . . 18

Table 2 SLSS Programming Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Changing Transfer Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Table 3 Routing Codes and Transfer Codes for SLSS Ports . . . . . . . . . . . . . 23

Chapter 5: Polling Controller and SLSS Operation/Features . . . . . . . . . . . . . . . . . . . . . . 25

Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Figure 5 Polling Controller and SLSS Operation. . . . . . . . . . . . . . . . . . . . . . 25

Typical Call Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Operational Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Polling Controller and SLSS Feature Operation . . . . . . . . . . . . . . . . . . . . . . 30

Table 4 Auxiliary Relay Secure Mode Commands

and Speed Mode Transfer Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Chapter 6: Standalone SLSS Operation and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Figure 6 Standalone SLSS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Example: Standalone SLSS Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Example: Alternative Standalone Call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Standalone Operational Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Standalone Feature Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Table 4 Auxiliary Relay Secure Mode Commands

and Speed Mode Transfer Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Chapter 7: Daisy-chain Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Figure 7 Daisy-chain SLSS Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Daisy-chain Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Programming for Daisy-chained SLSS Units . . . . . . . . . . . . . . . . . . . . . . . . . 48

Table 5 Routing Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Daisy-chain Remote Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Table 6 Remote Programming Daisy-chained SLSS Units. . . . . . . . . . . . . . 50

Appendix 1: About the SLSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Appendix 2: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

On-site Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Incoming Line Polarity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Substation Line Sharing Switch

Page ii

Routing Delays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Fax Routing Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Modem Lock Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Appendix 3: Warranty and Return. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Warranty Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Return Procedures

(U.S. Customers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Return Procedures

(Canadian Customers). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Appendix 4: Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Appendix 5: Ordering Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Appendix 6: Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Appendix 7: Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Reference Manual Contents

40-400-00031, Rev. A Page iii

U.S. FCC COMPLIANCE INFORMATION

FCC Part 68 (AHHUSA-75367-KX-T) Notice: To comply with FCC Part 68 regulations, the following requirements must be met:

1. If the telephone company requests information on the equipment connected to their lines, please tell them:

a. the telephone number the equipment is connected to;

b. this equipment operates on standard RJ-11 phone jacks;

c. the FCC registrationnumber;

d. the ringer equivalence number (REN 0.5 B). The REN shows how many devices, such as phones, modems, etc. can beconnected to your

line. In most areas, there cannot be more than five devices (i.e., a REN of five) on a phone line. If the REN is exceeded, thenyour phone may

not ring properly.

Note: Items C and D above are found on the label on Teltone equipment connected to your telephone line.

2. These devices must not be installed on coin-operated telephone lines or party lines.

3. Repair work on this device should be done by Teltone Corporation.

4. If any trouble isexperiencedwiththisequipment, thetelephonecompany may requestthatthecustomerdisconnect theregistered equipment fromthe

telephonelinetodetermineif theregistered equipment ismalfunctioningandif theregistered equipmentis malfunctioning,theuse ofsuchequipmentshall

be discontinued until the problem has been corrected.

Part 15 Class A Notice (M-395-A, B, D, E, M-396-A, B, D, E and M-390-A): This equipment has been tested and found to comply with the limits for a

ClassA digitaldevice, pursuant toPart 15 ofthe FCCRules. Theselimitsare designed toprovidereasonable protectionagainst harmfulinterferencewhen

the equipment isoperatedinacommercialenvironment. Thisequipment generates, uses,andcanradiateradiofrequency energy and, if notinstalledand

used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference, in whichcase the userwill be required to correct the interference at his ownexpense.

CANADIAN DOC COMPLIANCE

Notice: TheCanadian Department of Communicationslabel identifies certified equipment. This certificationmeans that the equipment meets certain

telecommunications network protective,operational, and safety requirements. The Department does not guarantee the equipment will operate to the

user’s satisfaction.

Before installing this equipment, usersshould ensure that it is permissible to connect it to the facilities of the local telecommunications company. The

equipment mustalso be installed using an acceptable method of connection. In some cases, the company’s inside wiring associated with a single line

individual service may be extended by means of a certified connector assembly (telephoneextension cord). The customer should be aware that

compliance withthe above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be made by the following authorized Canadian maintenance facility:

Can-am Telecommunications Associates Inc.

1845 Sandstone Manor, Unit 11

Pickering, Ontario, CANADA L1W 3X9

Phone: (905) 837-7700 Fax: (905) 839-3150

Any repairs or alterationsmade by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to

request theuser to disconnect the equipment.

Users should ensure for their own protection that the electricalground connections of the power utility, telephone lines, and internal metallic water pipe

system, if present, are connected together. This precaution may be particularly important in rural areas.

Caution: Usersshould not attempt to make suchconnectionsthemselves, butshould contact the appropriate electricinspection authority, or

electrician, as appropriate.

The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to beconnected to a telephone loop which is used

by the device, to prevent overloading. The termination ona loop may consist of any combination of devices subject only to the requirement that the

total of the Load Numbers of all the devices does not exceed 100. The Load Number assigned to the components of theTeltone Polling System

(M-390-A Polling Controller and M-395-A , B, D,and M-396-A , B, D SLSS) is LN 40, it is also located on theequipment label.

DOC COMPLIANCE NOTICE: TheM-395-A , B, D, andM-396-A, B, D SLSS do not exceed the Class A limits forradio noise emissions fordigital

apparatus as setout in the Radio Interference Regulations of the Canadian Department of Communications.

DOC AVIS DE CONFORMATION: Le présent apparel numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils

numériques de la class A prescritesdans le Règlement sur le brouillage radioélectriques addict par le minister des Communications du Canada.

Substation Line Sharing Switch

Page iv

About This Manual

This manual describes how to install, program, and operate the Teltone

M-395-A, B, D, and E four-port models and the M-396-A, B, D, and E eight-port

models of the Substation Line Sharing Switch (SLSS).

Conventions Used In This Manual

Underlined terms in the text are defined in Appendix 5.

Each step is accompanied by a check box:

Check the box when you finish the step.

Some steps include an example which look like this:

❑ This is an example step: follow this instruction to complete the example.

Where steps are optional, they are labeled: (Optional). Where you are to choose

between two or more options, they are separated by: -or-

This product is intended for the installations under the exclusive control of

electric utilities for the purpose of communication, or metering; or for the

generation, control, transformation, transmission, and distribution of electric

energy located in buildings used exclusively by utilities for such purposes or

located outdoors on property owned or leased by the utility or on public

highways, streets, roads, etc., or outdoors by established rights on private

property.

Reference Manual About This Manual

40-400-00031, Rev. A Page v

Substation Line Sharing Switch

Page vi

Chapter 1: Getting Started

Where To Start

Select one of the three configurations below to start. Read all instructions and the

examples in the text thoroughly before you begin.

SLSS and Polling Controller Configuration

• See Chapter 5 for a detailed description of operation before continuing.

• Follow the Are You Ready?, Installing the SLSS and Installing the Polling

Controller instructions in Chapter 3. When you finish, the system is ready

to route calls using the factory defaults.

• (Optional.) To use new transfer codes, follow the Changing Transfer Codes

steps in Chapter 3. Then, program the Polling Controller to send the new

codes to the SLSS by following the steps in Setup Polling Controller for

Programming in the Polling Controller Reference Manual.)

• (Optional.) If you choose to program the SLSS, you can do so remotely or

locally. See Setup for Remote Programming or Setup for Local Programming in

Chapter 4.

Standalone SLSS Configuration

• See Chapter 6 for a detailed description of Standalone operation before

continuing.

• If you will use the SLSS in standalone mode, without a Polling Controller,

follow the Are You Ready?, Installing the SLSS and Setup Standalone

Operation instructions in Chapter 3. When you finish, the SLSS is ready to

route calls.

• If you will be using a Polling Controller with the SLSS, please see the

optional instructions for installing a Polling Controller in Chapter 3. You

will also need the Reference Manual (40-400-00013) which comes with the

Polling Controller.

Daisy-chain SLSS Configuration

• This option is intended for experienced users. See Chapter 7 for a detailed

description of Daisy-chain operation before continuing.

• Both Standalone SLSS units and those working with a Polling Controller

can be daisy-chained. Follow the instructions for SLSS and Polling

Controller and/or Standalone SLSS. Please see the additional

programming information in Chapter 7.

Reference Manual Chapter 1: Getting Started

40-400-00031, Rev. A Page 1

Line Requirements

The SLSS works with

loop start telephone circuits and devices, not with ground

start. (Most telephone circuits and devices are loop start.) Please check with your

telephone company if you are uncertain about your telephone circuit.

Alarm LED

The red LED on the SLSS front panel lights during an alarm condition, such as

watchdog failure, checksum failure, or port timeout. As soon as the problem is

solved,thealarmLEDturnsoff.(Theinternalalarmrelay,whichisnormallyopen,

is wired to A1 andA2 ontherearpanel. Itwill close duringalarm conditions,and

the Alarm LED will turn on. As soon as the condition clears, the Alarm LED will

turn off and the relay will open.)

Compatibility

Any device that can be connected to a standard loop start telephone line,

including telephones, modems, and fax machines, is compatible with the SLSS.

The Call Waiting and Caller ID features offered by some telephone systems do

not work with the SLSS.

LED Indicators

Lights (LEDs) on the front of the SLSS tell you the status of the unit and ports.

Forexample,theLEDblinksquicklywhenacallisringingaport.Uniqueblinking

patterns indicate different functions, as shown in Table 1.

Table 1 LED Indicators on the SLSS

LED Operation Status LED

Port Status

LEDs

Slow blink, full to half

brightness

Idle, working properly —

Fast blink, full to half brightness Incoming call is ringing SLSS Ringing port

Slow blink, on/off In use: SLSS is off-hook toward line Timeout alarm

Steady on

Power present, but unit not functioning

properly

Port in use

(off-hook)

Off No power Idle

Power

In case of power loss, the SLSS will maintain a directpathbetween the Telco Line

Port and Port 1.

Auxiliary Relay

The relay is only available on models M-395/396-B, D,& E. The relay can be

opened, closed, or pulsed when its functionality is enabled. It may be used to

reset or to cycle power to a modem or other microprocessor-controlled device.

Substation Line Sharing Switch

Page 2

Chapter 2: Overview

The Teltone

SLSS has been designed to consolidate telephone lines at electrical

utility substations. It enables utilities having only one telephone line or those

using multiple telephone lines for data transfers to save costs through line

sharing. The SLSS also increases line efficiency by allowing devices, such as

telephones, modems connected to fault locating relays, meters, etc., and fax

machines to share a phone line in a substation. It can work with a Teltone Polling

Controllerasasystem(U.S.Patent No. 5,241,587)oritcanoperateasa standalone

unit to give you a flexible, cost-effective way to eliminate extra substation

telephone lines and route calls.

Figure 1illustratesa typicalapplication, inwhicha singletelephoneline isshared

by four devices.ThePolling Controller isadded to your existing hardware at the

data retrieval location.

The SLSS offers many benefits, some of which include its ability to:

• Share a single substation telephone line between up to eight devices.

• Eliminate expensive telephone line installation and monthly charges for

briefly used modem lines.

• Ensure correct call routing by using a Polling Controller.

• Enhance worker safety by giving priority to telephone users.

• Hide substation modems from unauthorized access.

• Obtain high reliability and availability with a unit providing C37.90 SWC

protection to attached devices and powered from 42-150 VDC batteries

(“A” and “B” models only) or 90-150VAC (“D” model only) or 90-220VAC

(“E” model only).

Figure 1 Typical SLSS Application

Reference Manual Chapter 2: Overview

40-400-00031, Rev. A Page 3

Chapter 3: Installation

Are You Ready?

Check that you have:

❑ Received an SLSS model M-395-A,B, D, E, M-396-A, B, D, or E. (The model

number is printed on the back of the unit.) Models ending in “-B , -D, or

-E” have the Auxiliary Relay.

❑ Received an Installation Kit which includes: two mounting brackets, two

tie cables, four pan-head slotted screws, four #12 flat washers, four #12

washer locks, four #12 wood screws, and four pan-head screws.

❑ Filled out and returned the Product Registration card.

❑ Collected enough standard modular telephone cords to connect the add-on

devices like modems, fax machines, meters, etc. to the SLSS. (The cords are

available as an ordering option.)

Installing the SLSS

Follow the appropriate steps below to wall-mount or mount the SLSS in a

standard 19" equipment rack. The brackets included in the installation kit are

used to mount the SLSS to a wall or to center- or front-mount the SLSS in an

equipment rack.

❑ To mount the SLSS on a wall, remove and discard the lower two center

screws on the SLSS side panels. Connect the short side of the mounting

brackets to the SLSS using the pan-head (round) screws provided. Then,

attach the mounting brackets to the wall with the supplied wood screws.

-or-

❑ To center-mount the SLSS in Equipment Rack, locate the center-most

screw holes and remove the two screws on the SLSS side panels and

discard. Use the pan-head (round) screws in the installation kit to attach

the brackets. Insert the SLSS into the rack and secure it with the provided

screws.

-or-

CAUTION:

(1) Never install telephone wiring during a lightning storm.

(2) Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

(3) Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected

at the network interface.

(4) Use caution when installing or modifying telephone lines.

Substation Line Sharing Switch

Page 4

❑ To front-mount the SLSS in Equipment Rack, remove the screws below

the threaded insert closest to the front of SLSS. Use the screws provided in

the installation kit to attach the the mounting bracket to the two vertical

holes closest to the SLSS front panel. Install the SLSS in the equipment

rack and secure it with the supplied screws.

❑ Locate the incoming Central Office telephone (CO) and plug it into the CO

Line jack on the back of the SLSS. (The incoming line comes from the

telephone RJ-11/wall jack.)

❑ Verify that the polarity of the incoming telephone line is correct. For more

detail, see Appendix 2: Troubleshooting.

❑ Connect the protective grounding to the screw above this symbol on the

barrier strip on the back of the SLSS. The SLSS must be grounded to operate

properly.

❑ Connect the SLSS to the incoming line in front of any other devices: all

devices that will be used with the SLSS must plug into it.

❑ If there are multiple CO lines, check the telephone numbers assigned to

each line to determine which connects to the SLSS.

❑ Plug a touchtone (DTMF) telephone into Port 1.

❑ Connect other devices (modems attached to fault recorders, meters, etc.) to

any of the other ports with standard telephone cords.

Figure 2 Installing the Central Office Telephone Line

Reference Manual Chapter 3: Installation

40-400-00031, Rev. A Page 5

ALARM

AUX

PORTS

STATUS

Substation Line Sharing Switch

2.37"

12.00"

11.80"

ALARM AUXPORTS

12345678

STATUS

Substation Line Sharing Switch

CAUTION:

FOR CONTINUED PROTECTION

AGAINST RISK OF FIRE,

REPLACE ONLY WITH SAME

TYPE AND RATING OF FUSE.

1.5AMP,

SLO-BLO,

3AG, 250V

LOAD NUMBER: XX

Bothell, WA U.S.A.

Made in U.S.A.

MODEL NO.:

UNIT NO.:

PART NO.:

MFG DATE:

WARR DATE:

THIS DEVICE COMPLIES WITH PART 15

OF THE FCC RULES. OPERATION IS

SUBJECT TO THE FOLLOWING TWO

CONDITIONS: (1) THIS DEVICE MAY NOT

CAUSE HARMFUL INTERFERENCE, AND

(2) THIS DEVICE MUST ACCEPT ANY

INTERFERENCE RECEIVED, INCLUDING

INTERFERENCE THAT MAY CAUSE

UNDESIRED OPERATION.

COMPLIES WITH PART 68, FCC RULES

FCC REG NO.: XXXXXX-XXXXX-XX-X

RINGER EQUIVALENCE: X.XB

PORT

C.O.

LINE

PORT

A1 R1

ALARMS AUX42-150 VDC

FUSE

A2 R2+

PATENT PENDING

PATEN 5,241,587

SLSS Front Panel

SLSS Rear Panel

Figure 3 Substation Line Sharing Switch (M-396-B-01)

Substation Line Sharing Switch

Page 6

❑ (Optional) Connect alarm monitoring equipment to the internal dry

contact alarm relay terminating at the barrier strip screws labeled A1 and

A2.

❑ For the “A” and “B” models, connect the power (42 - 150 VDC) leads to the

positive (+) and negative (-) screws on the barrier strip on the back of the

SLSS.

❑ For the “D” model, connect the power (90-150 VAC)) leads to the Line (L)

and Neutral (N) screws on the barrier strip on the back of the SLSS.

❑ For the “E” model, connect the power (90-220 VAC)) leads to the Line (L)

and Neutral (N) screws on the barrier strip on the back of the SLSS.

❑ Provide power to the SLSS and check that all LEDs light momentarily. The

Status LED will blink indicating the SLSS is idle. If power is lost to the SLSS,

a direct path between the C.O. Line port and Port 1 is maintained.)

❑ Run the wiring for the terminal block to the left of the unit, through the tie

block. Secure the wires using the “zip” ties.

❑ Replace the yellow terminal block cover.

❑ Run the CO Line and all port cabling to the right, through the tie block.

Secure the wires using the “zip” ties.

Route the wiring as shown to prevent noise on the telephone line.

PORT

C.O.

LINE

PORT

A1 R1

ALARMS AUX42-150 VDC

FUSE

A2 R2+

SLSS Rear Panel

Figure 4 SLSS Wiring Example

Reference Manual Chapter 3: Installation

40-400-00031, Rev. A Page 7

Install Polling Controller (optional)

If you are using the SLSS with the Polling Controller, follow these steps. These

instructions are repeated in the Polling Controller Reference Manual,

40-400-00013.ThesestepsrequireapersonatboththePollingControllerandSLSS

locations.

❑ Plug the incoming Central Office telephone line into the Telco Line port on

the back panel of the Polling Controller. (The incoming line comes from the

telephone RJ-11/wall jack.)

❑ Connect another standard modular telephone cord from the modem to the

Modem port on the back of the Polling Controller. (The cords are available

as an ordering option.)

❑ Connect a standard RS-232 cable from the modem to the computer (PC,

mainframe, or workstation) used to control polling.

❑ Connect the PS-24DC-01 power transformer cord to the jack labeled: Class

2 Input Power Pack, on the rear of the Polling Controller. Plug the power

transformer into a 120 VAC outlet.

❑ If you are using multiple Polling Controllers, see the Installing Multiple

Units in Carrier instructions in the Polling Controller Reference Manual

(40-400-00013).

❑ The power LED on the back panel should be flashing. If not, check that the

power is securely connected. (If the LED does not light, check the power

connection and fuse. If the LED is on bright, but does not flash, see the

Troubleshooting instructions in the appendix.)

❑ Place a call to the telephone connected to Port 1 on the SLSS. The call

should be answered by the SLSS on the first ring and the Port 1 telephone

should ring after four seconds. Answer the phone, then hang up.

❑ The system is ready to go to work. To call one of the ports on the SLSS, dial

the SLSS telephone number and add a routing code to the end.

❑ Test that calls are routed properly by plugging a device into Port 3 on the

SLSS, then call the SLSS and enter the routing code for Port 3. Check that

Port 3 rings and that the LED flashes on and off.

❑ Forexample:CallPort3ontheSLSSbydialing1-206-555-1212∗03fromaphone

plugged into the Polling Controller.

❑ Routing codes ∗01-∗08 sends calls to Ports 1-8 as follows: ∗01 routes calls to

Port 1, ∗02 to Port 2, and ∗03 to Port 3, etc.

❑ (Optional.) If you will not be using the default settings, see Programming

Tips in Chapter 4. To program the Polling Controller, refer to the Polling

Controller Reference Manual (40-400-00013).

Substation Line Sharing Switch

Page 8

Setup Standalone Operation

Follow the steps below to setup the SLSS to work without a Polling Controller.

Note:

Remember that if the SLSS will ever work with a Polling Controller,

the Polling Controller must be re-programmed with transfer codes which

match those of the SLSS.

❑ Disconnect the incoming CO line from the SLSS.

❑ Connect a DTMF telephone to Port 2 of the SLSS.

❑ Pick up the phone and enter # # within 15 seconds.

❑ When you hear the three-beep confirmation tone, enter ∗00#∗02# to

activate the Standalone defaults. Listen for the three-beep confirmation.

❑ Hang up the telephone and reconnect the incoming CO line to the SLSS.

❑ The power LED on the front panel should be flashing. If it is not, check that

the power is securely connected. (If the LED does not light, check the

power connection and fuse. If the LED is on bright, but does not flash, call

Technical Support.)

❑ Call the telephone connected to Port 1. The call should be answered by the

SLSS on the first ring and the Port 1 telephone should ring after four

seconds.

❑ Answer the phone, then hang up.

❑ Now you can call a port on the SLSS by adding the Standalone transfer

codes to the end of the SLSS phone number. (Standalone transfer codes

11-88 access Ports 1-8 as follows: 11 accesses Port 1, 22 accesses Port 2, and

33 accesses Port 3, etc.) See Chapter 4: Changing Transfer Codes to program

new codes.

❑ For example, to call Port 2, dial the SLSS number. Enter 22 after the first ring

(within 4 seconds).

-or-

❑ If you will not be using the Standalone Defaults, review the Programming

Tips in Chapter 4 and follow the Standalone SLSS Programming, also in

Chapter 4.

❑ (Optional) To call through a modem, remember to give the receiving

modem time to answer by adding pause time (,,,,) between the SLSS

telephone number and the transfer code.

If the modem does not answer properly, add or remove commas. If the call

defaults to Port 1, the pause is too long and you should remove one or

more commas. When adding or removing commas, do so one at a time.

Reference Manual Chapter 3: Installation

40-400-00031, Rev. A Page 9

The number of commas you will add depends on the time required for the

network to process your call and for the SLSS to answer the call.

❑ For example, to send a call to Port 3, dial: 1-206-555-1212,,,,33

Note:

The guesswork involved in determining the correct number of pauses

is why many users decide to use the Teltone Polling Controller.

❑ (Optional.) Continue to Chapter 4: Programming to review the Programming

Tips before following the Setup for Local, Remote or Standalone

Programming instructions.

Substation Line Sharing Switch

Page 10

Chapter 4: Programming

Programming Tips

You can adjust or program many of features in the SLSS. All of the options and

commands are listed in Table 2, later in this chapter. The SLSS is programmed

using a touchtone telephone, either locally, without disconnecting the CO Line,

or remotely from the Polling Controller.

Passwords

Always enter # after entering a password. If an invalid password is entered, you

will not hear three beeps and should hang up and wait for 30 seconds before

trying again. If three consecutive invalid attempts are made, the SLSS will lock out all

further access for 1 hour. (M-395-B, D, E models only: If secure relay access is

enabled, the SLSS will allow 5 consecutive invalid attempts.)

Note:

The password used to access the Auxiliary Relay must be different from

this password.

Remote Programming

Remote Programming must be enabled through Local Programming before you

can access the SLSS remotely. When you have finished programming remotely,

exit by hanging up the telephone. You cannot disable the Remote Programming

feature while in Remote Programming.

ConfirmationTone

When a command has been entered successfully, you will hear a three-beep

confirmation tone after entering the last #.

ErrorTone

When a command has been entered incorrectly, you will hear a single-beep error

tone after entering the last #.

Enable/Disable

With functions that are either enabled or disabled, such as fax routing, an entry

of 0 in the data field disables a feature; 1 enables it.

Cancel Command

To cancel the entirecommand, enter ∗in a command field. To cancel a command,

back to, but excluding the #, enter ∗ in a data field. To abort the entire command,

enter ∗∗ in a data field. If no data is entered in a field, that field is either cleared

or set to zero.

Reference Manual Chapter 4: Programming

40-400-00031, Rev. A Page 11

Transfer Codes

When assigning transfer codes for remote programming or for ports (commands

∗07#n#x# and ∗12#y#n#x#), follow these rules:

• Transfer codes must have the same number of digits, be no more than four digits

long, be unique (i.e., all codes must be different), and can use any of the 16 DTMF

digits.

• If you do not use the defaults, all codes must be programmed in both the

SLSS and Polling Controller.

Entering Programming Commands

You can enter the commands in any order. If you will not use a particular feature,

skip to the next and continue programming.

Threebeeps tellyou thattheSLSS received thecommand.One longtone tellsyou

that the command was incorrect and must be entered again. If you make a

mistake, simply re-enter the command correctly.

To enter a command, replace “n,” “x,” and “y” with the desired values.

❑ For example, to change the number of rings before disconnect from 12 to 10,

enter

∗01#10#.

❑ For example, to change the password to 1234, enter ∗03#1234#1234#.

❑ For example, to change the Port 2 transfer code to 8802, enter *12#2#4#8802#

Setup for Remote Programming with a Polling Controller

Note:

Programming may be interrupted if you have enabled Total or

Emergency Priority. If one of these priority modes is enabled, Port 1 will be

able to interrupt programming.

The SLSS will exit programming mode and disconnect if 60 seconds elapse

without entry of any digits.

The factory default for Remote Programming is enabled. If you have disabled

Remote Programming, it must be enabled before you can program.

You can access the SLSS for programming from the Polling Controller using a

special transfer code. You must enter a password after entering the Remote

Programming Transfer Code. The transfer code instructs the SLSS to answer

without ringing any of the device ports. Proceed as follows:

❑ Disconnect the Polling Controller from the host modem.

❑ Plug a DTMF telephone into the Modem port on the Polling Controller.

Substation Line Sharing Switch

Page 12

Page is loading ...

Teltone M-395-D-01 User manual

Brand: Teltone

Model: M-395-D-01

Type: User manual

This manual is also suitable for

Download PDF

report

Teltone M-395-D-01 User manual

This manual is also suitable for

Teltone M-395-D-01 User manual

Related papers

Other documents