Swing-N-Slide Playsets NE 4405 Operating instructions

Brand: Swing-N-Slide Playsets

Model: NE 4405

Type: Operating instructions

This manual is also suitable for

NE 4405-T

Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545

Visit our web site at: www.swing-n-slide.com/timberbilt or call us at 1-800-888-1232

TURBO TUBE

SLIDE

with Turbo Tower Kit

ASSEMBLY INSTRUCTIONS FOR ADDING THIS KIT

TO THE TIMBER•BILT

™

PINNACLE

™

INSTRUCCIONES DE ENSAMBLE PARA ADHERIR ESTE EQUIPO AL

TIMBER•BILT

™

PINNACLE

™

INSTRUCTIONS D’ASSEMBLAGE POUR AJOUTER CET ENSEMBLE À

L'UNITÉ PINNACLE

DE TIMBER•BILT

TB 1404

IMPORTANT! This product is intended for single family residential use only

and not intended for use in any public setting. Placement in

any public setting constitutes a misuse of this product.

REQUIRED SAFETY INSTALLATION INSTRUCTIONS

ANCHORING INFORMATION According to ASTM requirements, all rope ends must be anchored to the ground. If soil

conditions permit stakes to be pulled out easily, cementing into ground is necessary. In addition, Swing•N•Slide recommends

that all units be anchored to the ground. For quick and easy staking, purchase Swing•N•Slide NE 4521 Anchor-It Ground

Anchors.

• When anchoring the unit to the ground using wooden stakes, use 2" x 4" x 18" (45mm x 95mm x 457mm) pressure-

treated stakes. Pound stakes into ground at least 12" (305mm) at all inside corners of the posts (including A-frame legs and

climbing unit posts). Attach with four (4) 16D galvanized nails per stake into each 4" x 4" (95mm x 95mm) post.

• When anchoring a climbing rope with wooden stakes, anchor the rope end. Use a 2" x 4" x 18" (45mm x 95mm x

457mm) pressure-treated stake. Drill a 1-1/4" (32mm) or 1-1/8" (29mm) hole through the stake approximately 1-1/2" (38mm)

from the top of the stake. Cement stake into ground, leaving only the hole exposed. Insert rope end through hole in stake and

tie a knot in the rope to secure.

• Once the unit is completely assembled and before children are allowed to play on it, proper shock-absorbing

surfacing material must be installed. This may be accomplished by using loose-fill materials at a suf ficient depth. The

Consumer Product Safety Commission “Handbook for Public Playground Safety” lists the following materials and required

depths that are sufficient for home/residential application. For fall height protection up to 9 ft. (2.742m) [recommended for

Swing•N•Slide kits]:

CRITICAL HEIGHTS OF TESTED MATERIALS

MATERIAL UNCOMPRESSED DEPTH COMPRESSED DEPTH

6 inch 9 inch 12 inch 9 inch

Wood Chips* 7 feet 10 feet 11 feet 10 feet

Double Shredded Bark Mulch 6 feet 10 feet 11 feet 7 feet

Engineered Wood Fibers** 6 feet 7 feet >12 feet 6 feet

Fine Sand 5 feet 5 feet 9 feet 5 feet

Coarse Sand 5 feet 5 feet 6 feet 4 feet

Fine Gravel 6 feet 7 feet 10 feet 6 feet

Medium Gravel 5 feet 5 feet 6 feet 5 feet

Shredded Tires*** 10-12 feet N/A N/A N/A

* This product was referred to as Wood Mulch in previous versions of the Handbook for Playground Safety . The term Wood Chips more accurately describes

the product.

** This product was referred to as Uniform W ood Chips in previous versions of the Handbook for Playground Safety . In the playground industry, the product is

more commonly known as Engineered Wood Fibers.

*** This data is from tests conducted by independent testing laboratories on a 6 inch depth of uncompressed shredded tire samples produced by four

manufacturers. The tests reported critical heights which varied from 10 feet to greater than 12 feet. It is recommended that persons seeking t o install

shredded tires as a protective surface request test data from the supplier showing the critical height of the material when it was tested in accordance

with ASTM F 1292.

When properly installed, shock absorbing material will completely cover the horizontal baseboards on climbing units. This

protective surfacing must extend a minimum of 6 ft. (1.828m) in all directions from the perimeter of the equipment or from the

outermost edges of any component. For example, a slide extending beyond the platform must have protective surfacing at least

6 ft. (1.828mm) out from both sides as well as the end. For swings, with a 7' pivot point, the protective surface must extend at

least 14 ft. out from both the back and front of the swing when the swing is in its rest position.

INSTALLATION:

1. Read instructions completely prior to beginning assembly.

2. Do not deviate from these plans or alter design.

3. Be sure all hardware is tightened securely and flush to the intended member . Any caps provided which go over exposed

bolts must be fastened securely.

4. Upon final assembly, bolt ends shall not protrude beyond the nuts more than the diameter of the bolt when the nuts are

tightened to a torque between 20 & 25 lbf.in. (2.3 & 2.8 N.m). Remove any sharp edges with a metal file.

5. Place the equipment on level ground, not less than six feet (1.8 meters) from any structure or obstruction such as a

fence, garage, house, overhanging branches, laundry lines or electrical wires.

6. Do not install home playground equipment over concrete, asphalt, packed earth or any other hard surface. A fall onto a

hard surface can result in serious injury to the equipment user .

7. Verify that suspended ropes and chains (except those used for swings) are secured at both ends so that they cannot be

looped back on themselves.

8. To prevent serious injury, children must not be allowed in the area during assembly and they must not be allowed to use

the equipment until it is properly installed.

9. Save this plan for future reference.

The Sun: Slides should not have a southern exposure unless they are shaded from mid-day and afternoon sun. Unshaded

slides facing south can get hot and cause discomfort to bare skin. Northern exposures or shaded areas are definitely best.

OPERATION:

1. On-site adult supervision must be provided for children of all ages.

2. Be sure to teach children the following before allowing them to use the equipment:

A. Do not walk close to, in front of, behind or between moving items.

B. Do not twist swing or any other accessory chains or ropes or loop them over the beam as this will reduce the

strength of the chain or rope.

C. Do not swing empty seats or other accessories.

D. Sit in the center of the swing seat and other accessories with full weight on seat.

E. Do not use equipment in a manner other than intended.

F. Do not get off equipment while it is in motion.

G. Do not climb on the equipment when it is wet.

H. Do not attach items to the playground equipment that are not specifically designed for use with Swing-N-Slide

equipment, such as, but not limited to, jump ropes, clothesline, pet leashes, cables and chain as they may cause a

strangulation hazard.

3. Only one child per planned occupant seat should be allowed on this set at one time. Individual accessory weight

limitations may vary, see packaging for details.

4. Dress children appropriately for play. Avoid clothing with draw strings and loose fitting clothes which could become

entangled or snagged on equipment.

Safety First

PARENTS: Before building a backyard play area please take the time to read all

instructions completely and caution your children accordingly. Observing the following

statements and warnings reduces the likelihood of serious or fatal injuries.

When building this kit, at least two people are required for lifting and holding beams, frames or other heavy

assemblies in position before bolting or nailing. Special precautions must be taken when handling treated wood.

Contact your local supplier for specific information.

SAFETY - Wear safety glasses to protect your eyes from flying wood chips when cutting or drilling. Use a dust mask.

Blunt nail points to prevent wood from splitting. To prevent splinters, sand the corners, edges, and all the points of the

wood by wrapping a piece of 80 grit sandpaper around a block of wood and sanding.

CAUTION

SAFETY INSTRUCTIONS

Please read all of the Safety and Maintenance information on pages 2-4. Read through the remainder of this plan and familiarize

yourself with the lumber component guide, parts & hardware guide, installation directions and illustrations of this unit. Iden tify all

the components and check them off on the lumber, parts and hardware guides.

This plan is written and illustrated to provide you with the easiest method of assembly . If you experience problems during

assembly or are missing any components, please contact us at 1-800-888-1232, Monday through Friday , 8:00 a.m. - 5:00 p.m.

Central Time.

It is recommended that a shock absorbing material

should extend a minimum of 6 feet in all directions from

the perimeter of stationary equipment such as climbers

and slides. However, because children may deliberately

jump from a moving swing, the shock absorbing

material should extend in the front and rear of a swing

a minimum distance of 2 times the height of the pivot

point measured from a point directly beneath the pivot

on the supporting structure.

Example: For swings with a 7' pivot point, protective

surface must extend at least 14' out from

both the back and front of the swing when

the swing is in its rest position.

WARNING: Lawn swings are designed for use by children two years of age and older . Use by children under the age of two

can result in entrapment between the seats and back areas. NEVER place children in a rearward facing position or with legs

between seat and backrest because the child's body may pass through the opening causing entrapment of the child's head.

Maintenance:

1. Check all nuts and bolts twice monthly during the usage season for tightness and tighten as required. It is particularly

important that this procedure be followed at the beginning of each season.

2. Remove plastic swing seats and other plastic accessories and take indoors, or do not use when the temperature drops

below 0° F.

3. Oil all metallic moving parts monthly during usage period.

4. Check all hardware and equipment for sharp edges twice monthly during usage season and replace them as necessary . It is

especially important to do this at the beginning of each new season.

5. Check swing seats and protective sleeves for cracks. Cracks in the seat or sleeves are signs of deterioration. If these

conditions exist replace swing seat immediately. Call 1-800-888-1232 for more information about replacement.

6. Check chains, ropes and cables monthly during the usage season for signs of deterioration, severe rusting or excessive

wear (especially near the top swing hanger or at the seat connection). If these conditions exist replace af fected accessory

immediately. Call 1-800-888-1232 for more information about replacement.

7. Use a water seal on your gym set to protect the wood and prevent cracking and warping.

8. Sand rusted areas on tubular members and repaint using a nonlead-based paint meeting the requirements of

Title 16 CFR part 1303.

Disposal:

1. When the activity center is to be taken out of service, remove all play components and disassemble Dispose in such a way

that no unreasonable hazards will exist at the time the activity center will be disposed of. Dispose of following local dispos al

requirements.

SAFETY INSTRUCTIONS

(continued)

MINIMUM USE ZONE

BEFORE YOU BEGIN

14'

Page is loading ...

TOOLS REQUIRED

HERRAMIENTAS REQUERIDAS OUTILS REQUIS

(24) wood loc washers

(24) arandelas de traba de madera

(24) rondelles d’accrochage à griffes

(26) 5/16" Flat Washers

(26) arandelas planas de 5/16"

(26) rondelles plates de 5/16 po

(2) 1-1/2" lag bolts

(2) pernos de retraso de 1-1/2"

(2) tire-fonds de 1 1/2po

(24) 5" carriage bolts

(24) pernos de carro de 5"

(24) boulons de carrosserie de 5 po

(4) 7" carriage bolts

(4) pernos de carro de 7"

(4) boulons de carrosserie de 7 po

(24) loc nuts

(24) tuercas

(24) écrous de blocage

(274) 3" screws

(274) tornillos de 3"

(274) vis de 3 po

(105) 2" screws

(105) tornillos de 2"

(105) vis de 2 po

The hardware below is shown at actual size.

Las partes de abajo muestran el tamaño actual.

Les pièces de fixation sont illustrées en grandeur réelle.

KIT COMPONENTS

COMPONENTES DEL JUEGO

COMPOSANTS DE L’ENSEMBLE

1 Plan

(2) Ground Anchor Straps

(2) Tiras para anclar al suelo

(2) Attaches de pièce d’ancrage au sol

Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545

Visit our web site at: www.swing-n-slide.com/timberbilt or call us at 1-800-888-1232

TURBO TUBE

SLIDE

with Turbo Tower Kit

ASSEMBLY INSTRUCTIONS FOR ADDING THIS KIT

TO THE TIMBER•BILT

™

PINNACLE

™

INSTRUCCIONES DE ENSAMBLE PARA ADHERIR ESTE EQUIPO AL

TIMBER•BILT

™

PINNACLE

™

INSTRUCTIONS D’ASSEMBLAGE POUR AJOUTER CET ENSEMBLE À

L'UNITÉ PINNACLE

DE TIMBER•BILT

TB 1404

COMPONENT GUIDE FOR THE TURBO TUBE SLIDE

IS ON PAGES 26 & 27

A DE COMPONENTES PARA EL TUBO TURBO

RESBALADERA ESTA EN LAS PÁGINA S 26 Y 27

LE GUIDE DES COMPOSANTS DE LA GLISSOIRE

TURBO TUBE SE TROUVE AUX PAGES 26 ET 27.

(2) Anchor-It

™

Ground Anchors

(2) Anchor-It

™

Anclas de suelo

(2) Anchor-It

™

Pièces d’ancrage au sol

Power Drill, Circular Saw, Hammer, Socket Wrench, 1/2" Socket, Square, Tape Measure, Safety Glasses, Step

Ladder, 5/16" Drill Bit, 1-1/8" Spade Bit, #2 Phillips Head Bit

Taladro Eléctrico, Cerrucho Circular Eléctrico, Martillo, Llave Rachet, Dado de 1/2" Regla, Metro, Anteojos de

Seguridad, Escalera, Broca de 5/16", Broca de Espada 1-1/8", Desarmador Phillips #2.

Perceuse électrique, scie circulaire, marteau, clé à cliquet, douille de 1/2 po, équerre, ruban à mesurer , lunettes de

protection, escabeau, foret de 5/16 po, foret à trois pointes de 1 1/8 po, embout Phillips nº 2

Materials required

5 2" x 4" x 8'

1 2" x 4" x 10'

8 2" x 6" x 8'

2 2" x 6" x 10'

5 5/4" x 6" x 8' or

1" x 6" x 8'

3 5/4" x 6" x 10' or

1" x 6" x 10'

1 4" x 4" x 8'

2 4" x 4" x 10'

Pièces de bois requises

5 2po x 4po x 8pi

1 2po x 4po x 10pi

8 2po x 6po x 8pi

2 2po x 6po x 10pi

5 5/4po x 6po x 8pi or

1po x 6po x 8pi

3 5/4po x 6po x 10pi or

1po x 6po x 10pi

1 4po x 4po x 8pi

2 4po x 4po x 10pi

MATERIALS REQUIRED

MATERIALES REQUERIDAS

PIÈCES DE BOIS REQUISES

Materials requeridas

5 2" x 4" x 8'

1 2" x 4" x 10'

8 2" x 6" x 8'

2 2" x 6" x 10'

5 5/4" x 6" x 8' or

1" x 6" x 8'

3 5/4" x 6" x 10' or

1" x 6" x 10'

1 4" x 4" x 8'

2 4" x 4" x 10'

CUTTING GUIDE

GUÍA DE CORTAR

GUIDE DE COUPE

45-1/2" 45-1/2"

(1) 2" x 4" x 8'

40-1/4" 27" 27"

(1) 2" x 4" x 8'

47" 47"

(1) 2" x 4" x 8'

37-1/4" 37-1/4" 17"

(1) 2" x 4" x 8'

20" 20" 20" 9-1/4" 9-1/4" 7"

(1) 2" x 4" x 8' (slide brace)

37-1/4" 30-1/4" 27-1/4" 17"

(1) 2" x 4" x 10'

Page is loading ...

ASSEMBLY INSTRUCTIONS

PINNACLE PREPARATION

NOTE: Before beginning construction of

the Turbo Tower, several boards and rails

and rails must be cut or removed from

the Pinnacle.

1. Remove the top 2" x 4" board from the

front of the unit as indicated by removing

the screws at each joint.

2. Cut the 2" x 4" rail flush to the existing

upright as indicated. Remove the cut

board from the front of the unit as

indicated by removing the screws.

3. Remove the entire rail section of deck two

by removing the screws at the rail/post

joints.

4. Cut the 2" x 6" bottom support flush with

the existing 4" x 4" post as indicated.

Remove the carriage bolts and screws

from both pieces. NOTE: The section of

the bottom rail which is not shaded will be

re-used. Do not discard this section of

lumber.

5. Remove the carriage bolts and screws at

each end of the bottom 2" x 6" s as

indicated and remove.

6. Collect all lumber and hardware removed

and safely discard.

FIGURE 1

SAVE THIS PIECE OF LUMBER

GUARDE ESTE PEDAZO DE MADERA

CONSERVER CETTE PIÈCE DE BOIS

Page is loading ...

TOWER INSTALLATION

1. Reposition the bottom 2" x 6" x 38-1/4"

base board previously removed to the

back of the 4" x 4" posts. Counterbore

the front of the posts using a 1-1/8"

spade bit approximately 1/2" deep and

re-attach the board using two 5"

carriage bolts, wood loc washers,

washers and loc nuts.

2. Assemble the tower step as indicated in

Fig. 2A below using two 3" screws per

joint. Position the step assembly in the

opening as shown and attach to the unit

using two 3" screws on each side, both

top and bottom.

3. Attach the 2" x 6" x 91-1/2" and 2" x 6"

x 45-1/2" boards to the base of the unit

using four 3" screws per joint (two if

attaching to a 2" x 4" upright).

4. Using the existing bolt holes as a guide,

drill 3/8" holes through the previously

attached 2" x 6" base boards. Secure

each joint using a 5" carriage bolt, wood

loc washer, washer and loc nut.

5. Drill an additional hole through the

center upright and 2" x 6" base board

as indicated. Counterbore the 4" x 4"

approximately 1/2" deep at the hole

location. Secure the joint using a 5"

carriage bolt, wood loc washer, washer

and loc nut.

6. Attach the 2" x 6" x 40-1/4" base board

to the ends of the existing base boards

using two 3" screws per joint.

2" x 4" x 27-1/4"

2" x 4" x 17"

FIGURE 2

FIGURE 2A

ASSEMBLY INSTRUCTIONS

2" x 6" x 40-1/4"

2" x 6" x 38-1/4"

(existing board)

2" x 6" x 91-1/2"

2" x 6" x 45-1/2"

12" to top

12" en la base

de arriba

12 po de la

partie supérieure

Page is loading ...

TOWER INSTALLATION (cont.)

7. Attach two 2" x 6" x 37-1/4" and one

2" x 6" x 32-3/4" spacer boards to the

unit as indicated in Fig. 3 using four 3"

screws per joint.

8. Attach the 2" x 6" x 90" and 2" x 6" x

45-1/2" boards to the top of the unit

using four 3" screws per joint.

9. Position two 4" x 4" posts to the

assembly as indicated. Attach at the

top and bottom using four 3" screws

per joint.

10. Attach 2" x 6" x 40-1/4" to the top of

the posts using four 3" screws per

joint.

11. Using the existing bolt holes as a

guide, drill 3/8" holes through the

previously attached 2" x 6" x 90" top

board. Secure each joint using a

5" carriage bolt, wood loc washer,

washer and loc nut.

12. Drill 3/8" holes through the remaining

2" x 6" and 4" x 4" joints as indicated.

Counterbore the 4" x 4" approximately

1/2" deep at the hole locations. Secure

each joint using a 5" carriage bolt,

wood loc washer, washer and loc nut.

FIGURE 3

ASSEMBLY INSTRUCTIONS

2" x 6" x 45-1/2"

2" x 6" x 40-1/4"

4" x 4" x 120"

2" x 6" x 33-3/4"

(2) 2" x 6" x 37-1/4"

2" x 6" x 90"

Page is loading ...

DECK INSTALLATION

1. Attach two 2" x 6" x 45-1/2" deck

supports to the unit as indicated in

Fig. 4 using four 3" screws per joint.

NOTE: The tops of these boards

should be approximately 82-1/2" from

the ground and should be level.

2. Drill 3/8" holes through the 2" x 6"

and 4" x 4" joints of the deck supports

as indicated. Counterbore the

4" x 4" approximately 1/2" deep at

each hole location. Secure each joint

using a 5" carriage bolt, wood loc

washer, washer and loc nut.

3. Place 2" x 6" x 27-1/4" spacer board

between the deck supports and attach

using two 3" screws per joint. NOTE:

Do not allow screws to split the

surface of the 2" x 6" x 27-1/4" spacer .

If this occurs, back out screw and

reposition.

4. Place the 2" x 4" x 30-1/4" deck board

between the 4" x 4" posts as shown in

Fig. 5. Attach to the deck support

using two 3" screws per joint.

5. Place the 2" x 4" x 40-1/4" on the

supports as indicated in Fig. 5.

NOTE: The 2" x 4" x 40-1/4" deck

board should be tight against the

corresponding 4" x 4" posts and

should extend approximately 1-1/2"

past the edge of each post. Attach

using two 3" screws per joint.

6. Evenly space six 2" x 6" x 40-1/4"

boards between the previously

attached deck boards. NOTE: The

2" x 6" x 40-1/4" deck boards should

extend approximately 1-1/2" past the

edge of each post. Attach using two 3"

screws per joint.

ASSEMBLY INSTRUCTIONS

2" x 6" x 45-1/2"

2" x 6" x 27-1/4"

2" x 6" x 40-1/4"

(6 total)

2" x 4" x 30-1/4"

2" x 4" x 40-1/4"

FIGURE 4

FIGURE 5

82-1/2" to ground

82-1/2" a la tierra

82 1/2 po jusqu’au sol

Page is loading ...

TOP RAIL INSTALLATION

1. Drill a 3/8" hole through the 4" x 4" x

36" boards (2 are required)

approximately 8" from the top and

bottom of each board. Counterbore

each hole 1/2" deep.

2. Position each 4" x 4" flush with the top

of the deck and existing posts as

indicated in Fig. 6. Mark the hole

locations on the posts and drill 3/8"

holes through the 4" x 4" posts at the

marked locations.

3. Align the holes of the 4" x 4" x 36"

boards and the posts and secure

using two 7" carriage bolts, wood loc

washers, washers and loc nuts per

board.

4. Attach a 2" x 4" x 45-1/2" bottom rail

support to each side of the deck using

four 3" screws per joint. The rail

supports should rest on existing deck

boards.

5. Evenly space five 5/4" x 6" x 36" rail

uprights in each opening as shown in

Fig. 7. Attach the uprights to the

supports using two 2" screws at the

top and bottom of each board.

6. Attach a 2" x 6" x 37-1/4" board to the

front of the tower using four 3" screws

per joint. NOTE: The top of the 2" x 6"

x 37-1/4" should be flush with the top

of the deck.

7. Attach a 2" x 4" x 37-1/4" directly

below the previously attached board

using four 3" screws per joint.

ASSEMBLY INSTRUCTIONS

FIGURE 6

FIGURE 7

2" x 4" x 45-1/2"

4" x 4" x 36"

5/4" x 6" x 36"

2" x 6" x 37-1/4"

2" x 4" x 37-1/4"

4" x 4" x 36"

Page is loading ...

BOTTOM RAIL INSTALLATION

1. Attach a 2" x 4" x 37-1/4" rail support

to the front of the tower using four 3"

screws per joint. NOTE: The top of the

rail support should be approximately

30" from the bottom of the unit.

2. Attach two 2" x 4" x 47" rail supports

to the sides of the tower as shown in

Fig. 8 using four 3" screws per joint.

3. Evenly space five 5/4" x 6" x 30" rail

uprights in each side opening as

shown in Fig. 8. Attach the uprights to

the supports using two 2" screws at

the top and bottom of each board.

4. Evenly space four 5/4" x 6" x 30" rail

uprights in front of the tower as shown

in Fig. 8. Attach the uprights to the

supports using two 2" screws at the

top and bottom of each board.

FINAL TOWER ASSEMBLY

1. Attach a 2" x 4" x 37-1/4" directly

beneath the existing 2" x 6" using four

3" screws per joint.

2. Attach the two remaining 2" x 4" x 27"

and two 2" x 6" x 27" boards as

shown using four evenly spaced 3"

screws.

ASSEMBLY INSTRUCTIONS

FIGURE 8

FIGURE 9

2" x 4" x 37-1/4"

2" x 4" x 47"

2" x 6" x 27"

2" x 4" x 27"

5/4" x 6" x 30"

2" x 4" x 37-1/4"

2" x 6" x 27"

30"

Page is loading ...

FIGURE 1

FIGURE 2

FIGURE 3

Entrance Section - 14 bolts

Sección de Entrada - 14 pernos

Section d’entrée - 14 boulons

flanged lip

labio levantado

bord relevé

flat lip

labio plano

bord plat

Exit Section - 13 bolts

Sección de salida-13 pernos

Section de sortie - 13 boulons

90° Section (2 are required) - 13 bolts each

Sección 90° (se requieren 2) - 13 pernos cada una

Section à 90° (2 requises) - 13 boulons chacune

loc nut

tuerca

écrou de blocage

washer arandela rondelle

3/4" bolt

3/4" perno

boulon de 3/4 po

ENTRANCE SECTION, 90° SECTION (2)

AND EXIT SECTION

NOTES:

• At least two individuals are needed to

assemble the Turbo Tube Slide.

• To aid in aligning holes when assembling

sections, insert a screwdriver through adjacent

holes to maintain hole alignment.

1. Identify each slide section as either (1), (2),

(3), (4), (5), or (6) as marked on the lip of each

piece.

2. Assemble entrance section using pieces (1) &

(2), two 90° sections using pieces (3) & (4),

and the exit section using pieces (3) & (5).

Join sections using a 3/4" hex head bolt, two

flat washers, and a loc nut at each hole

junction (FIGURES 1, 2 & 3). NOTE: Fasten

each loc nut finger tight until the entire slide is

assembled. Each time you join parts be sure

each flanged lip is mating with a flat lip.

ASSEMBLY INSTRUCTIONS

Page is loading ...

FIGURE 4

MOUNTING PANEL

1. Position the mounting panel as indicated in Fig. 4

(The stamped "T" should be at the top). The

panel should be centered horizontally and the

bottom of the opening should be approximately 1"

below the deck surface.

NOTE: The holes identified with arrows (Fig.4)

should be clear of any wood surface.

2. Hold the panel in position and mark all hole

locations. Remove panel.

3. Drill a 3/8" hole through the top support at the

locations indicated in Fig.5 (two holes are

required).

4. Drill pilot holes at the remaining hole locations

using a 1/8" drill bit.

NOTE: The pilot holes at each corner hole

location should be approximately 2" deep. The

remaining pilot holes should only be 1" deep.

5. Align the mounting panel to the previously

assembled entrance section (see Fig. 7, page

32). Attach the mounting panel to the entrance

section at the hole locations indicated in Fig. 4

using one 1" bolt, two washers and one loc nut

per hole as indicated in Figure 6.

NOTE: Hand tighten the loc nuts only.

FIGURE 5

FIGURE 6

1" from top of deck

1" de la parte de arriba de la cubierta

1 po du haut de la plate-forme

ASSEMBLY INSTRUCTIONS

loc nut

tuerca

écrou de

blocage

washer

arandela

rondelle

washer

arandela

rondelle

1" bolt

1" perno

boulon de 1 po

Page is loading ...

TUBE ASSEMBLY

1. Position the 90° section to the entrance section

so the seams line up. Rotate the section two

holes to the right (clockwise) and realign with the

holes of the entrance section (see FIGURE 7).

2. Insert a 3/4" bolt through a washer, through the

holes of slide sections, a second washer and

secure with a loc nut.

NOTE: Insert first bolt and continue in a

clockwise rotation. Do not skip holes. Hand

tighten the loc nuts only at this time.

3. Position the 90° section to the previously attached

section so the seams line up. Rotate the section

two holes to the left (counterclockwise) and

realign with the holes of the entrance section (see

FIGURE 8).

4. Insert a 3/4" bolt through a washer, through the

slide sections, a second washer and secure with

a loc nut. NOTE: Hand tighten the loc nuts only at

this time.

FIG.URE 7

FIGURE 8

Rotate seam

two holes to

the right

(clockwise)

Girar el

dobladillo de

los agujeros a

la derecha

Tourner le joint

de deux trous

vers la droite

(sens des

aiguilles d'une

montre)

Rotate seam two

holes to the left

(counterclockwise)

Girar el dobladillo

de los agujeros a la

izquierda

Tourner de deux

trous vers la

gauche (sens

contraire à celui

des aiguilles

d'une montre)

ASSEMBLY INSTRUCTIONS

Page is loading ...

TUBE ASSEMBLY (CONT.)

5. Position the exit section to the previously

attached sections so the seams line up.

Rotate the section two holes to the left

(counterclockwise) and realign with the

holes of the entrance section (see

FIGURE 9).

6. Insert a 3/4" bolt through a washer,

through the slide sections, a second

washer and secure with a loc nut.

NOTE: Hand tighten the loc nuts only at

this time.

7. Position the slide base to the slide

assembly as indicated in FIGURE 10.

8. Insert a 3/4" bolt through a washer,

through the slide sections, a second

washer and secure with a loc nut.

9. Tighten all of the bolts of the slide

sections securely at this time.

NOTE: Do not tighten the bolts of the

mounting plate at this time.

FIGURE. 9

FIGURE 10

Rotate seam two

holes to the left

(counterclockwise)

Girar el dobladillo

de los agujeros a la

izquierda

Tourner de deux

trous vers la

gauche (sens

contraire à celui

des aiguilles

d'une montre)

dimple

marke

encoche

dimple

marke

encoche

hole

perfore

trou

ASSEMBLY INSTRUCTIONS

Page is loading ...

MOUNTING SLIDE

1. The help of at least one other individual

will be required for mounting the slide.

2. Insert the 2-3/4" bolts through a washer,

through previously drilled 3/8" holes in the

upper rail of the unit (see FIGURE 11).

3. Carefully lift the slide assembly to the

opening of the unit. Place the mounting

panel/slide assembly on the 2-3/4" bolts

previously inserted (see FIGURE 11).

Place washers and loc nuts on the bolts

and hand tighten.

4. Adjust the mounting panel/slide assembly

until the holes of the mounting panel align

with the previously drilled pilot holes.

5. Attach the top corners of the mounting

panel/slide assembly first using a 2-1/2"

lag bolt and washer . Secure the

remainder of the panel/slide assembly to

the unit using 1-1/2" lag bolts and

washers at each open hole location (8 are

required).

6. Tighten the 2-3/4" bolts securely.

7. Attach the bottom corners of the mounting

panel/slide assembly using a 2-1/2" lag

bolt and washer.

SLIDE BASE

1. Remove approximately 3" of grade

directly beneath the base of the slide.

FIGURE 11

FIGURE 12

2-3/4" bolt

2-3/4" perno

boulon de 2-3/4 po

washer

arandela

rondelle

washer

arandela

rondelle

washer

arandela

rondelle

washer

arandela

rondelle

washer

arandela

rondelle

loc nut

tuerca

écrou de

blocage

loc nut

tuerca

écrou

de blocage

2-3/4" bolt

2-3/4" perno

boulon de 2-3/4 po

2-1/2" lag bolt

pernos de retraso de 2-1/2"

tire-fond de 2 1/2 po

1-1/2" lag bolt

pernos de retraso de 1-1/2"

tire-fond de 1 1/2 po

ASSEMBLY INSTRUCTIONS

Page is loading ...

SUPPORT AND BRACKET ASSEMBLY

1. Position the slide bracket between the slide and

activity center (FIGURE 13). Remove

appropriate bolts from the slide (the fourth and

fifth bolts as indicated), Attach bracket to the

underside of the seam using the previously

removed hardware (FIGURE 13).

2. If necessary, move slide towards the activity

center until the slide bracket makes contact with

the unit. Using holes in the bracket (indicated by

arrows in FIGURE 13) as a guide, mark and

drill 1/8" pilot holes (1" deep). NOTE: You may

need to temporarily remove the slide bracket to

drill the pilot holes.

3. Re-attach bracket (if necessary) and secure it to

the unit using two 1-1/2" lag bolts .

4. Assemble the support base as shown in

FIGURE 14. NOTE: Use four 2" screws to

fasten the 2' x 4' x 9-1/4" boards and 3" screws

for remainder of assembly.

5. Attach the support bracket to the support base

using two 1-1/2" lag bolts (FIGURE 15).

NOTE: Pre-drill 1/8" pilot holes.

6. Place the support beneath the slide base and

determine its final position. NOTE: Slide

support should fit tightly beneath the slide to

assure proper support. Remove corresponding

nut and bolt, attach support to the slide as

indicated in FIGURE 16. Re-attach hardware.

7. Level grade at the bottom of the slide.

FIGURE 13

FIGURE 14

slide bracket

braqueta del resbaladero

support de glissoire

1-1/2" bolt

1-1/2" perno

boulon de 1-1/2 po

exit section

sección de salida

section de sortie

2" x 4" x 9-1/4"

2" x 4" x 7"

2" x 4" x 20"

2" screws

tornillos de 2"

vis de 2 po

3" screws

tornillos de 3"

vis de 3 po

washer

arandela

rondelle

loc nuts

tuercas

écrous de

blocage

2" x 4" x 9-1/4"

FIGURE 16

ASSEMBLY INSTRUCTIONS

FIGURE15

1-1/2" lag bolts

pernos de retraso

de 1-1/2"

tire-fonds de 1 1/2po

support bracket

braqueta de soporte

ferrure de support

Page is loading ...

Impresso en EE.UU.

Imprimé aux États-Unis

FINAL ASSEMBLY

1. Ground Anchors are provided with this kit and must be installed at each corner of the Turbo Tower.

2. Screw a ground anchor into the ground near each 4" x 4" corner post of the tower until only the triangular head

remains (see FIGURES 17 and 18).

3. Insert a strap through the head of the anchor. Align holes of strap as illustrated and attach to the unit using one

1-1/2" lag bolt and washer per anchor.

ENSAMBLAJE FINAL

1. Anclas de tierra se proveen con este equipo y deben ser instaladas en cada esquina de la torre de turbo

2. Atornillar un ancla detierra a 4"X 4" en el poste de la esquina hasta que sólo quede la cabeza triangular .

3. Insertar una cuerda por el ancla. Alinear los agujeros como se ilustra y adhiera a la unidad usando un perno de

atrás de 1-1/2" y una arandela por ancla.

ASSEMBLAGE FINAL

1. Des pièces d’ancrage sont fournies avec cette unité et elles doivent être installées dans chacun des

coins de la tour Turbo (Turbo Tower).

2. Visser une pièce d’ancrage dans le sol près de chacun des montants de 4 po x 4 po de l’unité en ne laissant

dépasser que la tête triangulaire (voir les FIGURES 17 et 18).

3. Insérer une attache dans la tête triangulaire de la pièce d’ancrage. Aligner les orifices des attaches comme le

montre l’illustration et fixer chaque attache à l’unité en utilisant un tire-fond de 1 1/2 po et une rondelle par

pièce d’ancrage.

FIGURE 17

FIGURE 18

Swing-N-Slide Playsets NE 4405 Operating instructions

Swing-N-Slide Playsets NE 4405 Operating instructions

This manual is also suitable for

Swing-N-Slide Playsets NE 4405 Operating instructions

in other languages

Related papers

Other documents