Page 1
INSTRUCTION MANUAL
3LT Interior Pendant
The Home Depot SKU 843-803 (UPC6940500304373)
Page 2
Thank you for purchasing this Commercial Electric interior pendant. This
product has been manufactured with the highest standards of safety and quality.
FEATURES:
1. Three-light interior pendant in rustic iron finish with antique ivory glass.
2. Includes 96-inch wire and 72-inch chain for open entry-way and cathedral
ceiling installations.
3. This fixture has been engineered to safely use three 60 watt medium base
incandescent light bulbs (do not exceed 60 watts each) (not included).
4. For energy savings, this fixture has been engineered to safely use three
standard base compact fluorescent light bulbs (for equivalent light output,
do not exceed 15 watts each) (not included).
QUESTIONS, PROBLEMS, MISSING PARTS:
Before returning to your local The Home Depot, please call our Customer
Service Team at 1-877-527-0313or visit www.homedepot.com. Please
reference your SKU 843-803 or UPC 6940500304373.
Page 3
CAUTION:
1. Before starting installation of this fixture or removal of a previous fixture,
disconnect the power by turning off the circuit breaker or by removing the
fuse at the fuse box.
2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY
ELECTRICAL QUESTIONS.
3. If you have any non-electrical questions about this fixture, please contact
our Customer Service Team at 1-877-527-0313 or visit
www.homedepot.com. Please reference your SKU 843-803 or UPC
6940500304373.
4. Keep your receipt and these Instructions for Proof of Purchase.
TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION
(not included):
3 Light Bulbs Safety Goggles Ladder Gloves Wire Strippers
(60 watt maximum)
(or CFL equivalent)
Flathead Screwdriver Phillips Screwdriver Electrical Tape Wire Cutters Pliers
Page 4
PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):
1ea Canopy (#1) 1ea Screw Collar Loop (#2) 6 feet Chain (#3) 1ea Ring (#4) 1ea Loop (#5)
3ea Lock Nuts (#7) 3ea Screws (#8) 1ea Hex Nut (#14) 1ea Nipple B (#15) 1ea Steel Washer (#16)
3ea Curve Arms (#9)
1ea Plastic Washer (#17) 3ea Lock Nuts (#18) 1ea Shade (#19) 3ea Screws (#20)
1ea Fixture Frame (#22)
1ea Washer (#21) 1ea Bottom Cover (#23) 1ea Finial (#24)
ASSEMBLY INSTRUCTIONS:
1. Carefully unpack the fixture. Lay out all parts on a clean surface.
2. Screw the Loop (#5) onto Nipple A (#6). Use pliers and a screwdriver to twist open the link (cover
the chain with cloth to prevent damage to the link finish) at the end of the Chain (#3) not attached to
the Screw Collar Loop (#2). To avoid damage to the link, only open the link enough to hook it onto
the Loop (#5). Hook the open link to the Loop (#5) and then close the link.
3. Weave the fixture wires up through the Loop (#5), through the Chain (#3), through the Ring (#4),
through the Screw Collar Loop (#2), through the Canopy (#1), and through the Nipple (#31 on Page
7) on the Mounting Strap (#30 on Page 7). Screw the Nipple (#31) into the Screw Collar Loop (#2).
4. Place the Screw (#8) on the top of the Curve Arm (#9) into the hole located on the Cup, and secure
the Curve Arm (#9) by screwing the Lock Nut (#7) onto the Screw (#8). Repeat for the other two
Curve Arms (#9).
5. Unscrew the Finial (#24) from Nipple B (#15). Screw Nipple B (#15) into the Bracket (#13).
Tighten the Hex Nut (#14) against the
Bracket (#13) to secure the Nipple B (#15).
6. Place the Steel Washer (#16), the Plastic Washer (#17), the Shade (#19), the Washer (#21), the
Fixture Frame (#22) and the Bottom Cover (#23) around Nipple B (#15). Secure them by screwing
the Finial (#24) onto Nipple B (#15).
7. Place the hole located on the bottom of the Curve Arm (#9) onto the Screw (#20) on the Fixture
Frame (#22), and secure the Curve Arm (#9) by screwing the Lock Nut (#18) onto the Screw (#20).
Repeat for the other two Curve Arms (#9).
8. Install three 60 watt medium base incandescent light Bulbs (#12) (not included) or three equivalent
standard base compact fluorescent light bulbs (not included) in the Sockets (#11) in the fixture.
Page is loading ...
Page 6
PARTS INCLUDED FOR INSTALLATION (parts are not to scale):
3ea Wire Connectors (#27) 1ea Ground Screw (#28) 1ea Hex Nut (#29)
1ea Mounting Strap (#30) 1ea Nipple (#31) 2ea Outlet Box Screws (#32)
INSTALLATION INSTRUCTIONS:
1. Screw the Nipple (#31) a half-inch into the Mounting Strap (#30). Tighten the Hex Nut (#29)
against the Mounting Strap (#30) to secure the Nipple (#31). Attach the Mounting Strap (#30) to
the Outlet Box (#26) using the two Outlet Box Screws (#32). [Make sure the longer end of the
Nipple (#31) is facing outside when the Mounting Strap (#30) is attached to the Outlet Box (#26).]
2. Adjust the Chain (#3) to required height by using pliers and a screwdriver to twist open (cover
the chain with cloth to prevent damage to the link finish) the link of Chain (#3) attached to the
Loop (#5), lifting the fixture and attaching to a link closer to the ceiling. To avoid damage to the
link, only open the link enough to hook it onto another link. The fixture can be raised and
lowered in this manner until the desired height is achieved. Next, use pliers to twist open (cover
the chain with cloth to prevent damage to the link finish) the first unused link of Chain (#3).
Remove and save the excess chain. Pull the excess fixture wires through the Nipple (#31) into the
Outlet Box (#26). Wires may be left at full length or shortened as determined by space in the
Outlet Box (#26) to make the wire connections.
3. Wrap the ground wire from the fixture around the Ground Screw (#28) on the Mounting Strap
(#30), and then connect the ground wire from the fixture to the ground wire from the Outlet Box
(#26). Connect the wire without writing on it (with raised ribs) from the fixture to the white wire
(neutral wire) from the Outlet Box (#26). Connect the wire with writing on it from the fixture to the
black wire (live wire) from the Outlet Box (#26). Cover the three connections using the three Wire
Connectors (#27). Wrap the three wire connections with electrical tape for a more secure
connection. Position the wires back inside the Outlet Box (#26). Note: If you have electrical
questions, consult your local electrical code for approved grounding methods.
4. Place the Canopy (#1) over the Nipple (#31) all the way to the ceiling. Tighten the Ring (#4) onto
the Screw Collar Loop (#2) until the Canopy (#1) is held firmly against the ceiling.
5. Installation is complete. Turn on the power at the circuit breaker or fuse box. Turn the light switch
on to activate the fixture.
Page is loading ...
Page 8
TROUBLESHOOTING:
PRODUCT MAINTENANCE:
1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean
water, never a solvent) to wipe the glass and surface of the fixture.
2. To clean the inside of the fixture, first disconnect power to the fixture by turning off the
circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly
dampened clean cloth (use clean water, never a solvent) to wipe the inside glass and interior
surface of the fixture.
3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry soft
cloth to dust or wipe carefully.
LIMITED WARRANTY
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period
of five (5) years from date of purchase. This warranty applies only to the original consumer purchaser and only to
products used in normal use and service. If this product is found to be defective, the manufacturer’s only
obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s discretion,
provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations,
neglect or mishandling. This warranty shall not apply to any product that is found to have been improperly
installed, set-up, or used in any way not in accordance with the instructions supplied with the product. This
warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration,
or faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not
apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal
wear and tear. The manufacturer does not warrant and specially disclaims any warranty, whether express or
implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer
specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage,
including but not limited to any labor / expense costs involved in the replacement or repair of said product.
Problem Possible Cause Corrective Action
1. Light bulb is burned out. 1. Replace light bulb.
2. Power is off. 2. Make sure power supply
is on.
3. Faulty wire connection. 3. Check wiring.
Light Bulb will not
illuminate.
4. Faulty switch. 4. Test or replace switch.
Fuse blows or circuit breaker
trips when light bulb is
illuminated.
Crossed wires or power wire
is grounding out.
Check wire connections.
Page 9
MANUAL DE INSTRUCCIONES
Pendiente para Interiores 3LM
The Home Depot SKU 843-803 (UPC 6940500304373)
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
