Bunker Hill Security Item 99938 Owner's manual

Brand: Bunker Hill Security

Model: Item 99938

Type: Owner's manual

This manual is also suitable for

INSTRUCTIONS AND PRECAUTIONS

Distributed exclusively by Harbor Freight Tools

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

SAVE THESE INSTRUCTIONS. READ ALL

PRECAUTIONS AND INSTRUCTIONS.

2008 by Harbor Freight Tools

herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this document may not be drawn proportionally. Due to continuing improvements, actual product

may differ slightly from the product described herein. Tools required for assembly and service may not be included.

For technical questions or replacement parts, please call 1-800-444-3353.

SPECIFICATIONS

Light Dome 6 LED, Bright White

Sensor Detector Range/Angle 16 ft. / 100 Deg.

UNPACKING

When unpacking, make sure that the item

is intact and undamaged. If any parts are missing

or broken, please call Harbor Freight Tools at the

number shown on the cover of this document as

soon as possible.

IMPORTANT SAFETY

INFORMATION

Assembly Precautions

Mount only according to these instructions. 1.

Improper mounting can create hazards.

Wear ANSI-approved safety goggles.2.

Keep assembly area clean and well lit.3.

Keep bystanders out of the area during 4.

mounting.

Do not mount when tired or when under the 5.

inuence of drugs or medication.

Use Precautions

This product is not a toy. Do not allow chil-1.

dren to play with this item.

Use for intended purpose(s) only.2.

Inspect before use; do not use if parts are 3.

loose or damaged.

Maintain product labels and nameplates. 4.

These carry important safety information.

If unreadable or missing, contact Harbor

Freight Tools for a replacement. Assembly

Instructions

LED MOTION

DETECTOR

LIGHT

99938

SKU 99938 For technical questions, please call 1-800-444-3353. Page 2

Read the ENTIRE IMPORTANT

SAFETY INFORMATION section at the

beginning of this document including

all text under subheadings therein

before set up or use of this product.

Mounting

This Motion Detector can be mounted on a 1.

drywall or solid surface.

The weight of the batteries may not permit 2.

mounting at an angle.

The Motion Detector is designed to operate 3.

when placed in a dark area or room.

Inspect the area where the Motion Detector 4.

is to be mounted for hidden wiring or piping.

Using the Mounting Bracket (2) (see Fig. 1) 5.

as a template, drill two 1/8" mounting holes.

Insert the two supplied plastic Wall Anchors a.

(5) into the holes if mounting onto drywall.

Place the mounting bracket against the 6.

mounting surface aligning the holes.

Insert each screw through the holes in the 7.

mounting bracket, and screw all the way into

the Wall Anchors (5) or solid stud surface.

The Mounting Bracket should now be se-8.

curely mounted on the surface. Pull rmly to

be sure bracket is secure.

Operation

Turn Motion Detector over and slide the battery 1.

compartment cover downward (see Fig. 2.)

Install the four 1.5V AA batteries. (Supplied.)2.

The proper polarity is shown in the battery a.

compartment.

Replace the battery compartment cover.3.

The Motion Detector mounting clips can now 4.

slide into the Mounting Bracket (2) clips.

The top of the Motion Detector has a three 5.

position switch:

The left position turns the six LEDs manu-a.

ally on, and stays on.

The center position turns the LEDs off, and b.

stays off.

The right position enables the “Auto” feature. c.

Any movement within the specied area d.

turns the six LED lights on for one minute.

To replace batteries or change switch posi-6.

tion, slide Detector upward and out from the

mounting bracket.

PARTS LIST

Part Description Qty.

1 Motion Detector 1

2 Mounting Bracket 1

3 AA Alkaline Batteries, 1.5V (Supplied) 4

4 Screws: 1-3/4"L x 1/8" Dia. (Not Shown) 2

5 Wall Anchors: 1-3/16"L x 3/16" ID (Not Shown) 2

Record Serial Number Here:

Note: If product has no serial number, record

month and year of purchase instead.

Note: Some parts are listed and shown for illustra-

tion purposes only, and are not available

individually as replacement parts.

PLEASE READ THE FOLLOWING

CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS

PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM

IN THIS DOCUMENT AS A REFERENCE TOOL ONLY.

NEITHER THE MANUFACTURER OR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY

KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED

TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT

HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF

THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR

DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS

AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN

BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT

BY THE BUYER. THE BUYER ASSUMES ALL RISK AND

LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE

ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO,

OR ARISING OUT OF HIS OR HER INSTALLATION OF

REPLACEMENT PARTS THERETO.

Fig. 1

Mounting

Bracket

Clips

Fig. 2

Back of Detector

Bunker Hill Security Item 99938 Owner's manual

Brand: Bunker Hill Security

Model: Item 99938

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Bunker Hill Security Item 99938 Owner's manual

This manual is also suitable for

Bunker Hill Security Item 99938 Owner's manual

Related papers

Other documents