Unpacking your phone
Corded Telephone
1. Where to find it
2. Installation
1. Locating the Base unit
The Base unit should be placed on a level surface, in a position where:
the telephone line cable will reach your telephone line socket or
extension socket.
it is not close to a sink, bath or shower, or anywhere else where
it is not close to other electrical equipment - fridges, washing
machines, microwave ovens, TVs, fluorescent lights, etc.
2.
4. Plug one end of the telephone line cord into the socket in the back
5.
Lift the Handset and check for Dial tone
in the earpiece.
Always use the
telephone line
cord supplied
with your
Other telephone
line cords may
not work.
2. Installation
it might get wet.
Making a
1
Press the SPEAKERPHONE button,
2 Dial the telephone number you wish to call.
3
To end the call,press the SPEAKERPHONE
call
To answer a
call
4. Telephone Operation
In the box you will find:
x Base Unit
x Handset
x Coiled Handset cord
x Telephone line cord
for Base unit
x User manual
Keep the packing
materials in a safe
place in case you later
need to transport
Keep your sales (till)
receipt, which is your
guarantee.
the unit.
3. Desk/W
2. Installation
3. Wall mount installation
BE CAREFUL to check that there are no wires or pipes hidden in the wall.
Hang the base unit on the screws using the wall mount slots.
You may need to remove the telephone from the wall and tighten the screws so
cradle with the
parking hook on the cradle
arranged to fit in the
parking recess
that the cradle is securely fixed and does not wobble
. Place the Handset on the
When the phone rings;
Press the
button to
SPEAKERPHONE
answer call.
PB10
PB10 phone.
1. Number / photo memory button
2. VOL-(volume-)/STORE button
3. Speakerphone( ) button
- This flashes
when the phone is ringing
To Modular
Wall Jack
6. Ringer ON/OFF( )button
Wall mount
To place the PB10 phone on a wall,
on the wall that are
mm
centers as
.
mark two
apart to lay the fixing
points
shown below
speakerphone
volume
During a call;
Adjust the volume of the speakerphone to the
SPEAKERPHONE
volume button located at the
left and right side of the speakerphone button.
Press the SPEAKERPHONE button on the
Base unit.
Ö
The IN USE light indicator will
To end a call
turn OFF.
To adjust the
4. IN USE/RINGER( )-in Use /ringer light
the phone is on a call.
of the base unit, and plug the other end into a modular wall jack.
under the earpiece on the Handset.
high or low volume level using the
Fix two screws (7mm head screws required, not supplied)
approximately 7mm
at the marked locations,
between the wall and the screw head.
leaving
VOL-
VOL+
Listen for a dial tone.
button.
93mm
93
If you have a
Broadband line
If you connect your telephone to
insert a micro-filter between the
otherwise you may get
interference between the telephone and the broadband,
which could cause problems.
a line with a broadband
connection, you will need to
In a home with broadband, every telephone must have a micro-filter connected,
not just the one at the telephone point that your modem is connected to.
If you need more broadband micro-filters, contact your broadband supplier.
telephone and the telephone line,
TELEPHONE
1
- This is on when
for an incoming call.
5. VOL+(volume+)/PAUSE button
6
2
3
4
5
Or Visit Our Website:
WWW.binatonetelecom .com
Connection and conditions for use
You can connect your PB10 phone to a direct exchange line ( DEL)
The ringer equivalence numbers (RENs) of all instruments (phones, fax
machines, etc.) connected to an exchange line must not add up to more
- otherwise, one or more of them may not ring and/or answer calls
The PB10 phone has a REN of 1, and most other telephones have
Contents of this User Guide
UK Ver1.0 28-Mar,2011
Standard
Temperature range Operating 0 ºC to 40 ºC
Storage -20 ºC to 60 ºC
PBX compatibility Timed break recall: 100 ms. Pause length: 3.0
Signalling type: DTMF (dual-tone multifrequency)
6. Technical details
seconds.
also called tone dialling.
than 4
correctly.
- a line connected to a local exchange, with its own phone number; to
an extension socket connected to a DEL; or to an extension on an
approved compatible PBX. Do not connect the
extension to a pay phone.
a REN of 1 unless marked otherwise.
1. Where to find it
2. Installation
3. Wall mount installation
4.
Telephone operation
5.
6.
Pressing buttons on your phone
When the instructions in this user guide tell you simply to ‘press ’ a
button, this means that you should press the button briefly, then
.
press and hold’ buttons for any functions on this
Guarantee and service
Technical details
release it
Inserting a
Press the PAUSE button immediately after
Pause in
For some switchboard systems, an access
the dialling
sequence
Press PAUSE button to insert a pause
1
2
number must be dialled (usually an 8 or 9)
5. Guarantee and service
Press a (0-9,*or # )button to store the
Storing a
Number in
(0-9,* or #)
photo
memories
1
In standby mode, press STORE button.
2
Key in the telephone number you wish to
3
Up to a maximum 24 digits.
Ö
store.
PB10 phone as an
PB10 Telephone
Network connection This equipment is intended to be used in the UK
Operation on other countries’ PSTN termination
.
points cannot be guaranteed
only.
Waste electrical products must not
be disposed of with household waste.
This equipment should be taken to
your local recycling centre for safe
treatment.
EC Declaration of Conformity
We the manufacturer / Importer : Binatone Telecom Plc
1 Apsley Way London
NW2 7HF, United Kingdom.
Declare under our sole responsibility that the following product
Type of equipment:
Corded Phone
Model Name: PB10
Country of Origin:
China
Brand:
Binatone
complies with the essential protection requirements of R&TTE Directive 1999/5/EC on the
approximation of the laws of the Council Directive
/108/EC on the approximation of
the laws of the Member States relating to
electromagnetic compatibility (EMC)
and the
European Community Directive 2006/95/EC relating to
Electrical Safety.
Assessment of compliance of the product with the requirements relating to the essential
requirements according to Article 3 R&TTE was based on Annex III of the Directive
1999/5/EC and the following standard:
EMC:
Electrical Safety:
The product is labelled with the European Approval Marking CE as show. Any Unauthorized
modification of the product voids this Declaration.
Manufacturer / Importer
(signature of authorized person)
London,
Signature: Place & Date: 28th Mar, 2011
EN55022:2006+A1
EN55024:1998 + A1+A2
EN 60950-1:2006+A11:2009
This product is guaranteed against manufacturing defects for
a period of 1 Year.
This does not cover the product where the fault is due to
misuse, abuse, use in contravention of the instructions, or
where the product has been the subject of unauthorised
In the event of a problem with the product within the
guarantee period please return it to your nearest Argos store.
If the item is shown to have had an inherent defect present
at the time of sale,
Your statutory rights remain unaffected.
commercial use.
modifications or alterations, or has been the subject of
the store will provide you with a
replacement.
BTP
the access number to insert a pause of
number can be dialled immediately.
when dialling or storing Long Distance
to get another dial tone and an outside line.
Access Codes.
Press the STORE button .
4
C
Ö
Dial out
Stored
number
1
(0-9,* or #)
photo
memories
about 3 seconds, and the desired
number in the selected memory.
To dial a number stored in photo
memory (0-9,* or #)
Key in the memory location number
The number dials
automatically and
You do not need to ‘
phone.
VOL+
VOL+
PAUSE
PAUSE
VOL-
STORE
VOL-
STORE
Your memory is saved when
Ö
(0-9,* or #)
the IN USE light will turn on.
In standby mode.
In Speakerphone mode.
C
Ö
Key in the memory location number
The number dials
automatically.
(0-9,* or #)
Dial out
Stored
number
1
(0-9,* or #)
photo
memories
from standby
mode
1
Press the SPEAKERPHONE button,
Listen for a dial tone.
2
The IN USE light will turn on.
Ö
from
speakerphone
mode
Telephone Operation continue...
Press and hold the button until you
hear a 'Beep'.
Ö
The ring tone will
To turn
turn OFF.
the ringer
OFF
Ringer light - This flashes only when the
phone is ringing for an incoming call.
Press and hold the button until you
hear two 'Beep'.
Ö
The ring tone will
turn ON.
Ringer light - This flashes with ring tone when
the phone is ringing for an incoming call.
To turn
the ringer
ON
Product Operation Director
________________________________________ .
BINATONE TELECOM PLC
1 Apsley Way London NW2 7HF,United Kingdom.
Tel: +44(0) 20 8955 2700 Fax: +44(0) 20 8344 8877
e-mail: [email protected]
k
________________________________________ .
hear a 'beep'.
Or Visit Our Website:
WWW.binatonetelecom .com
-
1
-
2
Binatone PB10 User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Binatone Acura 3000 User manual
-
Binatone Acura 3000 Call Blocker User manual
-
-
Binatone iDECT V2 Quin User manual
-
Binatone 410 User manual
-
-
-
-
-
Binatone BB3200 User manual