PQQW15288ZA DC0906PW0
FX-2/4
Digital Cordless Phone
Model No. KX-TG7150FX
KX-TG7170FX
1 Connections
2 Battery installation/
Battery charge (Initial charge: 7 hours)
Note:
L Use only the included rechargeable batteries.
Quick Guide
(220–240 V, 50 Hz)
To telephone network
Hook
Use only the included AC adaptor
and telephone line cord.
The pictured model is KX-TG7150.
Charge
contact
TG7150FX_7170FX(e)_QG.fm Page 1 Thursday, August 24, 2006 10:48 AM
– 2 –
3 Bone conduction earpiece (KX-TG7170 only)
Note:
L The effectiveness of the bone conduction earpiece will vary by the type and degree of
hearing loss of the user.
4 Symbols used in these operating instructions
Display language
17 display languages are available.
You can select “Deutsch”, “English”, “Türkçe”, “Magyar”, “Polski”, “slovensky”,
“ČeŠtina”, “Hrvatski”, “Slovenscina”, “Eesti”, “LIETUVIŠKAI”, “LatvieŠu”,
“Românã”, “БЪЛГАРСКИ”, “Srpski”, “МАКЕДОНСКИ”, or “Shqiptar”.
1 {ih} i {j/OK}
2 Press {^} or {V} to select “Handset Setup”. i {>}
3 Press {^} or {V} to select “Display Setup”. i {>}
4 Press {^} or {V} to select “Select Language”. i {>}
5 Press {^} or {V} to select the desired language. i {>} i {ih}
Dialling mode (tone/pulse)
1
{j/OK}
2 Press {^} or {V} to select “Base Unit Setup”. i {>}
3 Press {^} or {V} to select “Call Options”. i {>}
4 Press {^} or {V} to select “Dial Mode”. i {>}
5 Press {^} or {V} to select the desired setting. i {>} i {ih}
The handset features a
bone conduction
earpiece that uses
vibrations to create
sound during your
telephone
conversations.
Place the bone conduction
earpiece against your face
(not your ear).
Try different locations to
find which location works
best. Start with the temple
area.
Symbol Meaning
{j/OK} Press {j/OK}.
i Proceed to the next operation.
“” Select the words in quotations shown on the display (e.g., “Handset
Setup”) by pressing {^} or {V}.
Bone conduction
earpiece
TG7150FX_7170FX(e)_QG.fm Page 2 Thursday, August 24, 2006 10:48 AM
– 3 –
Date and time
1
{j/OK}
2 Press {^} or {V} to select “Handset Setup”. i {>}
3 Press {^} or {V} to select “Time Settings”. i {>}
4 Press {^} or {V} to select “Set Date & Time”. i {>}
5 Enter the current day, month, and year.
6 Enter the current hour and minute.
7 {j/OK} i {ih}
5 Accessibility
Caller ID announce
When you receive an outside call which has phone number information, the handset
announces the displayed phone number from the handset speaker.
L To announce outside caller’s phone number, you must first subscribe to Caller ID service.
Consult your service provider/telephone company for details.
List announce
The handset announces phone numbers from the handset speaker while you are viewing the
redial list, caller list, and phonebook.
6 Basic operations
Feature Operation
Making a call Dial the phone number. i {C}/{s}
Answering a call {C}
Hanging up {ih}
Receiver/speaker volume Press {^} or {V} while on a call.
Last number redial {R} i {C}
Making a call with redial list {R} i Press {^} or {V} to select the desired
number. i {C}
Handset phonebook: storing an
entry (name and phone
numbers)
{k} i {j/OK} i “New Entry” i {>} i
Enter the party’s name (16 characters max.). i
{j/OK} i Enter the party’s phone number (24 digits
max.). i {j/OK} i “Save” i {>} i {ih}
L To enter a name, see the character table in the
operating instructions.
Handset phonebook: making a
call
{k} i Press {^} or {V} to display the desired entry.
i {C}
TG7150FX_7170FX(e)_QG.fm Page 3 Thursday, August 24, 2006 10:48 AM
– 4 –
7 Frequently asked questions
Handset ringer volume {j/OK} i “Handset Setup” i {>} i
“Ringer Setup” i {>} i “Ringer Volume”
i {>} i Press {^} or {V} to select the desired
volume. i {>} i {ih}
Changing ringtone
(outside calls)
{j/OK} i “Handset Setup” i {>} i
“Ringer Setup” i {>} i “Ext. Ringtone”
i {>} i Select the desired ringtone. i {>} i
{ih}
Question Cause & solution
What kind of power outlet
should I connect the AC
adaptor to?
L Connect the AC adaptor to a 220–240 V outlet.
Why is w flashing? L The handset is too far from the base unit. Move closer.
L The AC adaptor is not connected. Check the
connections.
L You are using the handset or base unit in an area with
high electrical interference. Place the handset and base
unit away from interference sources, such as antennas
and mobile phones.
L The handset is not registered to the base unit. Register it.
{j/OK} i “Handset Setup” i {>} i
“Registration” i {>} i “Register H.set” i
{>} i Press and hold {x} on the base unit for about 3
seconds, until the registration tone sounds. i Wait until
“Enter Base PIN” is displayed. i Enter the base unit
PIN (default: “0000”). i {j/OK}
Why can I not make calls? L The dialling mode setting is incorrect. Set to “Tone” or
“Pulse” as needed.
Why is the handset display
blank?
L The handset is not turned on. To turn the power on, press
{ih} for about 1 second.
What should I do when the
handset does not turn on?
L Make sure that the batteries are installed correctly.
L Fully charge the batteries.
L Clean the charge contacts and charge again.
How long should I charge new
batteries?
L Charge the batteries for about 7 hours.
Feature Operation
TG7150FX_7170FX(e)_QG.fm Page 4 Thursday, August 24, 2006 10:48 AM
– 5 –
How long is the battery
operating time?
L When you are using fully-charged Ni-MH batteries
(included batteries);
In continuous use: 12 hours max. (KX-TG7150)/ 10 hours
max. (KX-TG7170)
In continuous standby mode: 150 hours max.
– It is normal for batteries not to reach full capacity at the
initial charge. Maximum battery performance is
reached after a few complete cycles of charge/
discharge (use).
– Actual battery performance depends on a combination
of how often the handset is in use and how often it is
not in use (standby).
Can I keep the handset on the
base unit when I am not using
it?
L Even after the handset is fully charged, the handset can
be left on the base unit without any ill effect on the
batteries.
When should I replace the
batteries?
L If the batteries are fully charged until 1 is displayed,
but 3 is displayed after a few calls, replace the
batteries with new ones.
What is a PIN? L The PIN is a 4-digit number that must be entered in order
to change certain base unit settings. The default PIN is
“0000”.
What do I need to do to
display caller information?
L You need to subscribe to Caller ID service. Consult your
service provider/telephone company for details.
L The message “You must first subscribe to
Caller ID.” will be displayed until you receive caller
information after subscribing to Caller ID service.
Question Cause & solution
TG7150FX_7170FX(e)_QG.fm Page 5 Thursday, August 24, 2006 10:48 AM
– 6 –
8 Optional service (Caller ID)
If you subscribe to Caller ID service, you can:
– display caller information
– announce the caller’s phone number (Caller ID announce)
Tom
012345
TG7150FX_7170FX(e)_QG.fm Page 6 Thursday, August 24, 2006 10:48 AM
/