Dometic RM7211LSC User manual

Category
Fridge-freezers
Type
User manual

This manual is also suitable for

Dometic RM7211LSC is a gas absorption refrigerator for inland waterways craft. It features an automatic ignition, interior light, and a sealed combustion system. The refrigerator has a 12V DC power supply and a 230V AC mains power supply. It has a capacity of 70 liters and a freezer compartment. The refrigerator can be used to store food and drinks, and can be used to make ice cubes. It has a number of features to make it easy to use, such as a thermostat to regulate the temperature, and a door lock to keep the contents secure.

Dometic RM7211LSC is a gas absorption refrigerator for inland waterways craft. It features an automatic ignition, interior light, and a sealed combustion system. The refrigerator has a 12V DC power supply and a 230V AC mains power supply. It has a capacity of 70 liters and a freezer compartment. The refrigerator can be used to store food and drinks, and can be used to make ice cubes. It has a number of features to make it easy to use, such as a thermostat to regulate the temperature, and a door lock to keep the contents secure.

Type C40 / 110
T.B. 01/2004
MANUAL
ABSORPTION - REFRIGERATOR for INLAND WATERWAYS CRAFT
EN
English
OPERATING INSTRUCTIONS
INSTALLATION INSTRUCTIONS
RM 7211 LSC
RM 7401 LSC
Model number
.............................................
Product number .............................................
Serial number .............................................
Record for future reference:
2
Instructions for storing food in a refrigerator:
No refrigerator of any kind can improve the quality of the food; refrigerators can only maintain the food's quality for a short
duration as from the time of storing it.
Please observe the following particular conditions for storing food in a refrigerator that is built into a vehicle:
- A change in the climatic conditions such as temperature fluctuations
- High temperatures inside the vehicle when it is closed and parked in direct sunlight (temperatures are possible
up to 50°C)
- Use of the refrigerator whilst travelling with the power supply of 12V--DC
- A refrigerator built in behind a window and exposed to direct sunlight
- Storing the goods too soon, i.e. shortly after switching the device on for use
Under these particular conditions the refrigerator cannot guarantee having the temperature needed for food that perishes
quickly.
Foods that perish quickly include: all the products with a stipulated use-by date and a minimum storage temperature of +4°C
or less, especially for meat, poultry, fish, sausage, pre-packed foods.
Instructions
- Pack raw and cooked foods separately (e.g. in containers, aluminium foil, etc.)
- Only remove the outside packaging of single packs if all the necessary data, such as the use-by date, for
example, can also be read on the single packs.
- Do not leave cooled goods outside the refrigerator for too long.
- Place the foods with the next use-by date at the front, accordingly.
- Pack away any left-over food again and eat at the first opportunity.
- Wash your hands before and after touching any food.
- Clean the inside of the refrigerator at regular intervals.
Information :
Please observe the instructions and information regarding the use-by date on the outside packaging of the food.
Please observe the following sections in these instructions: "5.1 Cleaning" and "5.3 Storing food".
Safety instructions
These operating instructions should be kept in a safe place.
If this device is passed on, please include these operating instructions with it.
©
Dometic GmbH - 2004 - Subject to change without notice - Printed in Germany
3
1.0 INTRODUCTION 4
2.0 FOR YOUR SAFETY 4
2.1 Warning and safety notices 4
2.2 Coolant 4
3.0 WARRANTY AND CUSTOMER 5
SERVICE
3.1 Damage in transit 5
4.0 DESCRIPTION OF MODEL 5
5.0 REFRIGERATOR GUIDE 5
5.1 Cleaning 5
5.2 Switching on the refrigerator 6
5.3 Storing food 9
5.4 Making ice cubes 9
5.5 Defrosting 10
5.6 Winter operation 10
5.7 Switching off 10
5.8 Door locking 11
5.9 Interior light 11
5.10 Changing the decor panel 12
5.11 Positioning the storage racks 12
5.12 Changing the doorhang 13
5.13 Troubleshooting 14
5.14 Maintenance 15
5.15 Product liability 15
5.16 Environmental hints 15
5.17 Disposal 15
5.18 Energy-saving tips 15
5.19 Technical data 16
5.20 Declaration of conformity 16
6.0 INSTALLATION GUIDE 17
6.1 Installation 17
6.2 Installation recess 18
6.3 Ventilation and air extraction 19
6.4 Installation of the ventilation 20
and fume system
6.5 Securing the refrigerator 22
6.6 Gas installation 22
6.7 Electrical installation 24
6.8 Wiring diagrams 25
6.9 Supplied equipment 26
TTAABBLLEE OOFF CCOONNTTEENNTTSS
Warning
Attention
Information
Environmental
Advice
4
INTRODUCTION
You have made an excellent choice in selecting the Dometic Absorption Refrigerator.
We are sure that you will be fully satisfied with your new appliance in all respects.
The appliance, which works silently, meets high quality standards and guarantees
the efficient utilisation of resources and energy throughout its entire life cycle, during
manufacture, in use and when being disposed of.
Before you start to use the appliance, please read the installation and operating
instructions carefully.
The refrigerator is designed for installation on inland waterways craft . The appliance
has been certified for this application in accordance with EU Gas Directive
90/396/EEC.
FOR YOUR SAFETY
Warning and Safety Notices
Never use a naked flame to check the appliance for leaks.
Protect children!
When disposing of the refrigerator, remove all refrigerator doors and leave the
storage rack in the refrigerator. This will prevent accidental locking in or suffocation.
If you smell gas:
- close the gas cock of the gas supply and the valve on the cylinder.
- open the windows and leave the room.
- do not switch on anything electrical.
- extinguish naked flames.
Never open the cooling unit; it is under high pressure.
Work on the gas, flue system and electrical components must only be
carried out by qualified service personnel.
It is imperative that the operating pressure should correspond to the data given on
the model plate of the appliance.
Compare the operating pressure data given on the model plate with the data on the
pressure monitor of the liquid gas cylinder.
Liquid gas cylinders may only be changed by qualified personnel.
Covers ensure electrical safety and must only be removed using a tool.
The appliance must not be exposed to rain.
The refrigerator is not suitable for the proper storage of medications.
Coolant
Ammonia is used as a coolant.
This is a natural compound also used in household cleaning agents (1 litre of
Salmiak cleaner contains up to 200g of ammonia - about twice as much as is used in
the refrigerator).
Sodium chromate is used for corrosion protection (1.8% of the solvent).
In the event of leakage (easily identifiable from the unpleasant odour):
switch off the appliance.
air the room thoroughly.
inform the authorised Customer Service department.
11..00
22..00
2.1
2.2
Danger Attention
5
WARRANTY AND CUSTOMER SERVICE
Warranty arrangements are in accordance with EC Directive 44/1999/CE and the
normal conditions applicable for the country concerned. For warranty or other servicing,
please contact your supplying dealer. Any damage due to improper use is not covered
by the warranty. The warranty does not cover any modifications to the appliance or the
use of non-original Dometic parts; the warranty does not apply if the installation and
operating instructions are not adhered to and no liability shall be entertained. Parts can
be ordered from your dealer.
When contacting your dealer, please state the model and product numbers.
You will find these informations on the data plate inside the refrigerator.
Damage in Transit
After removing the packaging, please check whether the refrigerator has been
damaged during transportation.
Any damage sustained in transit must be reported to the transportation company
concerned no later than seven days after delivery of the goods.
DESCRIPTION OF MODEL
REFRIGERATOR GUIDE
Cleaning
Before using the refrigerator, it is advisable to clean the appliance both inside and
out, and repeat this at regular intervals.
Use a soft cloth and lukewarm water with a mild detergent.
Then rinse the appliance with clean water and dry thoroughly.
Remove dust from the refrigerator unit at yearly intervals using a brush or soft cloth.
To avoid deterioration of materials:
Do not use soap or hard, abrasive or soda-based cleaning agents.
Do not allow the door seal to come into contact with oil or grease.
33..00
44..00
55..00
5.1
RM 7401 LSC
e.g.
Refrigerator Mobile /
Mobile Absorber Refrigerator
Last digit 1 = automatic ignition
L with interior light, Sealed Combustion
3.1
6
Switching On the Refrigerator
The refrigerator is silent in operation.
When the appliance is first put into operation, there may be a mild odour which will
disappear after a some hours. Ensure the living area is well ventilated.
The freezer compartment should be cold about one hour after switching on the
refrigerator.
The refrigerator will take several hours to reach its operating temperature.
Before the refrigerator is put into operation at the gas mode or when the leak test
is carried out, the siphon (a) on the rear has to be filled with 20 ml of water. It is
recommended to use the water separator (b) while building in the appliance before
the fume and ventilation system is mounted. Otherwise use the flue pipe (c) for
filling in the water.
Controls
Note :
The refrigerator is equipped to operate mains power, DC or liquid gas.
The desired power option is selected by means of energy selector switch (A).
Energy selector switch (A) has four settings:
O (off), Gas (liquid gas), 230V (AC mains power), 12V (DC) .
5.2
5.2.1
b.
c.
a.
flue outlet
flue pipe
A = energy selection switch
B = gas/electric thermostat AC/DC
C = operating displays (3 LEDs)
A
B
C
AC mains power
12V DC
Gas
OFF
7
Electrical Operation
1. DC 12V
The refrigerator should only be used while the motor is running. Otherwise
the on-board-battery would be discharged within a few hours !
2. Mains Power
This option should only be selected where the supply voltage of the connection
for power supply corresponds to the value specified on the data plate.
Any difference in values may result in damage the appliance.
5.2.2
2. Use rotary switch (B) to regulate the
temperature in the main refrigerator
compartment.
A
1. Set energy selector switch
(A) to 12V .
Operating display C, 12V
lights green.
Appliance is in function.
C
If the operating display fails to light up the device is not in operation.
(For troubleshooting see 5.13)
B
2. Use rotary switch (B) to regulate the
temperature in the main refrigerator
compartment.
A
1. Set energy selector switch
(A) to 230V .
Operating display C, 230V
lights green.
Appliance is in function.
C
If the operating display fails to light up the device is not in operation.
(For troubleshooting see 5.13)
B
8
Gas operation
The refrigerator should only be operated using liquid gas
(only propane [red bottle] ). Do not use ISO-Butane
This appliance has a sealed combustion system.
Operation using gas is prohibited in petrol stations.
1. Open the valve of the gas cylinder
2. Open the gas cock to the gas supply.
The ignition process is activated automatically, accompanied by a ticking sound
approx. 30 sec. Upon successful ignition, the display LED (C) Gas lights yellow.
The refrigerator is in function. Use rotary switch (B) to regulate the temperature in
the main refrigerator compartment.
When using for the first time, and after changing the gas cylinder, the gas pipes
may contain air. By operating the refrigerator and any other gas appliances
(e.g. cookers), air is removed from the gas pipes. The gas will then ignite
without delay.
Gas faults
In the event of a gas fault (e.g. gas cylinder empty),
the operating display (C) flashes yellow.
Remedies :
Set the energy selector switch (A) to position OFF.
1. Is there any gas in the gas bottle?
2. Is the gas bottle valve open?
3. Is the on-board shut-off valve open?
4. Set the main switch (A) to on
The reignition starts again.
If after about 30 seconds the operating display (C) starts flashing red again, the
gas fault has not been cleared (e.g. air in the gas pipe).
5. Briefly switch the refrigerator off and then on again using main switch (A).
To remove air from the gas pipes, repeat this procedure 3-4 times.
If these actions do not help, please call an authorised Dometic Service Centre.
A
3. Set energy selector switch (A) to gas
4. Set rotary switch (B) to MAX position.
C
5.2.3
C
Automatic ignition
9
Temperature setting cooling compartment
As shown, you are able to regulate the temperature of
the cooling compartment, if necessary, by turning rotary
knob (B) .
Making Ice Cubes
Ice cubes are best frozen overnight. At night, the refrigerator has less work to do and
the unit has more reserves.
5.2.4
B
TTIIPP
medium setting
The cooling units performance is influenced by ambient temperatures.
Please select the medium setting for ambient temperatures between +15°C
and +25°C. The unit operates within its optimum performance range.
DOMETIC refrigerators work according to the absorption principle.
Due to physical reasons, an absorption system responds slowly to
changes made on the thermostat controller, or a loss in cooling through
opening the door, or storing food. The devices are subject to the Climatic
Class SN acc. to EN/ISO 7371 in the temperature range of +10°C to +32°C
ambient temperature
5.3
Storing food
5.4
Only use drinking water!
Switch the refrigerator on approx. 12 hours before filling it.
Always store pre-cooled foods in the refrigerator. Make sure that the food is well
cooled when it is bought and also when transporting it. Use insulated cooling bags.
When taking food out of the refrigerator only open the refrigerator door very briefly.
Foods must be packed - best of all in closed containers - and stored separately from
each other.
Allow foods that have been warmed up to cool down before storing.
Store quickly perishable foods directly next to the cooling fins.
The refrigerator must not be exposed to direct sunlight. Please bear in mind that
the temperature inside a closed vehicle increases sharply if exposed to sunlight and
that this can reduce the efficiency of the refrigerator.
The air inside the refrigerator unit MUST be able to circulate freely without any hin-
drance. (see also Section 6.3 "Ventilation and air extraction")
Products that could emit volatile, flammable gases must not be stored in the
refrigerator.
The freezer compartment is suitable for making ice cubes and for short-term storage of
frozen food. It is not suitable as a means of freezing foods.
1. Fill the ice
cube tray with
drinking water.
2. Place the ice cube
tray in the freezer
compartment.
Defrosting
As time goes by, frost builds up on the fins.
When the layer of frost is about 3mm thick, the refrigerator should be defrosted.
1. Switch off the refrigerator, as described in section 5.3 - "Switching off".
2. Remove the ice cube tray and food.
3. Leave the refrigerator door open.
4. After defrosting (freezer compartment and fins free of frost), wipe the
cabinet dry with a cloth.
5. Use a cloth to mop up the water from the freezer compartment.
6. Switch the refrigerator on again.
The layer of ice must never be removed forcibly, nor may defrosting be
accelerated using a heat source.
Note:
Water thawing in the main compartment of the refrigerator runs into an appropriate
container at the back of the refrigerator. From there, the water evaporates.
Winter Operation
Roof mounted flue outlet
Before the appliance is put into operation at the
gas mode the area around the flue outlet has to be
free of ice and snow or leaves. Periodically, check the
flue outlet. A layer of ice should be formed by conden-
sing water (from exhaust fumes).
Switching Off
10
5.5
5.6
5.7
Do not step on
flue outlet !
2. When the refrigerator is shut off for a long
period, leave the door ajar.
RM 7211 LSC
RM 7401 LSC
1. Set energy selector switch (A) to position (OFF).
The appliance is now fully switched off.
3. Secure the door open by means of the door
stop. The door will be slightly ajar. This is
to prevent mould from forming inside
the appliance.
A
Switching off gas operation
If the refrigerator is to be taken out of service for an extended period of
time, the on-board gas cock and the cylinder valve must be closed.
Door Locking
Interior Light
Changing the light bulbs
11
5.8
5.9
RM 7401 LSC
RM 7211 LSC
park-position
closed open
park-position / fixation
closeopen
1. Remove cover.
2. Detach defective light
bulb.
3. Fit new light bulb
4. Clip the cover back in
place.
90°
1.
2.
Note:
For 12V DC :
1 light bulb 12V, 2W
Please contact Dometic Service Centres for
replacement light bulbs.
12
Changing the Decor Panel
Dimensions of the panels in mm:
Model Height Width Thickness
RM 7211 LSC 534+/-1 453,5+1 3,2
RM 7401 LSC 730+1 491,5+1 3,2
Positioning the Storage Rack ( only RM 7401 LSC )
To fit the storage rack, the reverse order applies.
5.10
5.11
Dismantling:
1. Open the door
and loosen the
hinge screw.
2. Take off the door
by moving it upwards.
3. Unscrew the door strip
(3 screws).
4. Remove the decor
plate and insert a new
decor plate.
5. Screw the door
strip back in
position.
6. Put the door
back on.
7. Tighten the
hinge screw.
1. Loosen the front
and back securing
brackets.
2. Move the storage rack to the left and
remove it.
2.
1.
13
Changing the Doorhang5.12
Move the lower hinge
pin to the other side.
8. Screw the hinge
screw back in.
3.
4.
6.
7.
It is not always possible to change the door when the refrigerator is installed.
RM 7211 LSC
RM 7401 LSC
1. Open the door, unscrew the hinge screw .
2. Remove door lock and mount it at the
opposite side.
1. Open the door,
unscrew the hinge
screw and keep it to
hand.
2. Take off the door by
moving it upwards.
5. Attach the door.
14
Troubleshooting
Gas Operation with ISO-Butane
If used with ISO-Butane, the following problems can occur:
no ignition
the flame goes out within 2 to 3 minutes and the re-igniter continues to spark
the flame can be extinguished by products of combustion
Operation with ISO-Butane is not recomended.
5.13
Failure 1 : The refrigerator does not work in gas operation mode.
Possible cause Action you can take
a.) Gas bottle empty.
b.) Is the supply cut-out device open?.
c.) Is the flue outlet blocked ?
d.) Faults during ignition process ?
As the burner chamber is filled with
gas, ignition is not possible.
e.) If the appliance was not in use for a
long time, possibly there is no build-up
of thermal current in the exhaust pipe.
Before calling the authorised Service Department, please check whether:
1. the instructions in the section "Using the refrigerator" have been followed.
2. the refrigerator is not tilted excessiveley.
3. it is possible to operate the refrigerator with an available power source.
Failure 2 : The refrigerator does not work on 12V.
Possible cause Action you can take
a.) On-board fuse defective.
a.) Fit new fuse.
Failure 3 : The refrigerator does not cool sufficiently.
Possible cause Action you can take
a) Inadequate ventilation to the unit.
b) The thermostat setting is too low.
c) There is too much ice on the evaporator.
d) Too much warm food put inside.
a) Check that the flue outlet is not covered.
Check whether the refrigerator was instal-
led properly (Installation Guide).
b) Turn the thermostat to a higher setting.
c) Check that the refrigerator door seals
when shut.
d) Let food cool down first.
a.) Change gas bottle.
b.) Open the cut-out device.
c.) Clear away leaves, snow etc.
d.) Wait several hours to let the gas
vanish. Operate on 12V or 230V to
generate a thermal current.
e.) Switch on 12V mode or 230V mode
for approx. 30 minutes to warm up
the exhaust pipe.
5.13.1
15
Maintenance
Works on gas components and electical installation may only be carried out
by authorised personnel. We recommend to contact your Dometic Service
Centre.
EN 1949 stipulates that the appliance´s gas equipment and its associated fume
system must be inspected after installation and a certificate issued.
Afterwards a qualified technician must inspect according to EN 1949 every two
years and a certificate issued.
It is the users responsibily to arrange for inspections after purchase.
It is recommended that the gas burner be inspected and cleaned as necessary at
least once a year.
We recommend maintenance following an extended shutdown of the appliance.
Product liability
Product liability of Dometic GmbH does not include damages which may arise from
faulty operation, improper alterations or intervention in the equipment, adverse effects
from the environment such as changes in temperature and air humidity, which may
impact the equipment itself or the direct vicinity of the equipment or persons in the
area.
Environmental hints
Refrigerators manufactured by Dometic GmbH are free of CFC/HCFC and HFC.
Ammonia (a natural compound of hydrogen and nitrogen) is used in the cooling unit
as a coolant. The non-ozone-hazardous cyclopentan is used as a propellant in the
manufacture of the PU foam insulation.
Disposal
In order to ensure that the recyclable packaging materials are re-used, these should
be sent to the usual local collection system.
The appliance should be transferred to a suitable waste disposal company that will
ensure re-use of the recyclable components and proper disposal of the rest.
For eco-friendly draining of the coolant from all absorber refrigeration units, a suitable
disposal plant should be used.
Energy-saving tips
At an average ambient temperature of approx. 25°C, it is sufficient to operate the
refrigerator at the middle thermostat setting (for both gas and mains voltage).
Where possible, always store goods that have previously been cooled.
Do not position the refrigerator in direct sunlight.
Constant circulation of air must be supplied to the refrigerator unit.
Defrost regularly.
Open the door only for a short time when removing goods from the refrigerator.
Run the refrigerator for about 12 hours before filling it.
5.15
5.16
5.17
5.18
5.14
16
Technical Data
We reserve the right to make technical changes.
*Average consumption measured at an average ambient temperature of 25°C in pursuance of
ISO Standard.
Declaration
5.19
RM 7211 647x486x534 60 lit. 5 lit. 125 W / 120 W ca. 2,3 KWh / 250 g 22 kg X
RM 7401 853x525x598 97 lit. 10,5 lit. 135 W / 130 W ca. 2,6 KWh / 270 g 31 kg X
Model Dimensions Groos capacity Usable Connection * Consumption Netweight Ignition
H x W x D (mm) incl. freezer capacity of Mains / Battery electricity / gas Flame
depth incl. door compartment freezer in 24 hrs Failure
compartment Device
5.20
17
INSTALLATION GUIDE
On installation of the appliance, the technical and administrative regulations of the
country in which the vessel will first be used must be adhered to. Otherwise the
refrigerator must be installed as described in these instructions.
In Europe, for example, gas appliances, cable laying, installation of gas
cylinders, as well as approval and checking for leaks must comply with
EN 1949 for liquid gas units in vessels.
Installation
The appliance and its fume extraction shall be installed in such a way as to be acces-
sible for servicing at all times and must be capable of easy removal and installation.
The appliance may only be installed by authorised personnel.
Installation and connection of the appliance must comply with the latest
technical regulations, as follows:
Technical regulations, EN 1949
Technical regulations, EN 732
Technical regulations, EN-ISO 10239
Technical regulations, EN 624, ch. 5.5.2 , 6.5.2.2 (leak test at sealed
combustion systems)
The electrical installation must comply with national regulations
( for Europe EN 60335-1, EN 60335-2-24, EN 1648-1 , EN 1648-2).
The gas installation must comply with national regulations.
Local and building control department requirements
The appliance shall be installed in such a way that it is shielded from
excessive heat radiation.
Excessive heat impairs performance and raises the energy consumption of the
refrigerator.
66..00
6.1
Any installation that is not carried out by qualified persons will jeo-
pardize the manufacturers guarantee.
18
Installation Recess
There must be an air-duct at the back of the refrigerator to generate a
sufficient air-flow over the cooling unit to carry away the heat as shown in fig. 1.
The 40mm-feet are necessary to provide fresh air to allow sufficient
ventilation.
The appliance must be installed using the feet provided!
Recess measurements :
Model Hight H (min) Width W Depth T
RM 7211 LSC 650 mm 490 mm 510 mm
RM 7401 LSC 856 mm 529 mm 570 mm
6.2
min. 200
H
T
W
170
43400 (RM 7401)
813 (RM 7401)
607 (RM 7211)
340 (RM 7211)
Fig. 1 Fig. 2
upper ventilation grille
19
Ventilation and Air Extraction
The correct installation is important for correct operation of the appliance to ensure,
there is no build-up of heat at the back of the appliance. The heat must be allowed to
escape into the open air.
In the event of high ambient temperatures, full performance of the cooling unit
can only be achieved by means of adequate ventilation and extraction.
6.3
The illustrations show the air vent when the
refrigerator is installed .
1 = Opening Fresh Air Inlet
2 = Ventilation Grille
3 = Cold air going in
4 = Warm air coming out
Note: The fresh air inlet (1) must have
a clear cross section of at least
200 cm
²
(no ventilation grille).
The ventilation grille (2) must have a
clear cross section of at least
200 cm².
Do not install this way !
4.
2.
3.
1.
Ventilation
20
Installing the Ventilation and Fume System
6.4
1 = Exhaust Pipe
2 = Fresh Air Hose
3 = Sealing Ring
4 = Bottom Part (Flue)
5 = Top Part (Flue)
MOUNTED ON THE
APPLIANCE :
7 = Connection Fume
Extraction
8 = Water Separator /
Fresh Air Inlet
1.
2.
3.
4.
5.
Connections
7.
8.
Bolt (to secure the pipe)
Exhaust Pipe Ü silver / metal ; length : 500 mm supplied; 1500 mm available on special
request ; (approval min. 200 mm , max. 1500 mm)
The flared flange is fixed with a gasket and an union nut at the refrigerator and the
other side is fixed with a gasket and a bolt at the flue outlet.
Ensure that there is enough distance to flamable parts (min. 50mm).
(the exhaust pipe gets hot in use)
Fresh Air Hose Ü black / plastic ; length : 500 mm supplied; 1500 mm available on special
request; (approval min. 200 mm , max. 1500 mm)
The kit contents the following parts ( without the fixing screws ):
Pipe and Hose mounted
{
Union Nut
Gaskets
Hose Clamps
6
1.
2.
6.
6.
3.
92 mm
65 mm
6.
7.
8.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Dometic RM7211LSC User manual

Category
Fridge-freezers
Type
User manual
This manual is also suitable for

Dometic RM7211LSC is a gas absorption refrigerator for inland waterways craft. It features an automatic ignition, interior light, and a sealed combustion system. The refrigerator has a 12V DC power supply and a 230V AC mains power supply. It has a capacity of 70 liters and a freezer compartment. The refrigerator can be used to store food and drinks, and can be used to make ice cubes. It has a number of features to make it easy to use, such as a thermostat to regulate the temperature, and a door lock to keep the contents secure.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI